Strong SRT 7100 TV set-top boxe
Contents
1. respectively 0 9 to change the settings Once all settings are made press GREEN to save or EXIT to quit without saving Editing an existing satellite Use A Y to highlight the satellite you wish to edit Press BLUE to go to the Satellite Edit screen To edit the name of the satellite use to highlight the name and press A keyboard will pop up Use to navigate and OK to input the chosen character Once finished press GREEN to save the changes or EXIT to quit without saving To edit the position of the satellite use to move the highlight to Position and use the 0 9 buttons to input the new position To change the location use to highlight Location and use lt P to change the location Possible settings are East and West Once all settings are made press GREEN to save or EXIT to quit without saving Adding a satellite To add a satellite make sure the highlight is not in the transponders list press 4 in case of doubt and press YELLOW The procedure for adding a satellite is the same as for editing a satellite 7 2 Setup Use the Setup menu to configure the system settings of your receiver The following sub menus are available Language Output Options Time Setting Parental Control and OSD Display Choose the desired submenu with and press OK to advance 7 2 1 Language Here you can set the preferred Display Audio and Subtitle languages and Country setting Use A V to highlight the setting you wish2. LNB Power QPSK 8 PSK DVB S QPSK 1 45 Ms s 10 30 Ms s Auto 1 2 2 3 3 4 5 6 7 8 in DVB S mode 1 2 2 3 3 4 3 5 4 5 5 6 8 9 9 10 in DVB S2 mode 2 3 3 5 3 4 5 6 8 9 9 10 in DVB S2 8PSK mode MPEG 2 MP ML MP HL 4 264 Max 90 Mbit s 4 3 16 9 Pan amp Scan Letterbox Combined 25 Hz for PAL 30 Hz for NTSC 576p 720p 1080i 1 Layer 1 amp 2 MPEG 4 264 Downmix Mono L R Stereo AC 3 20 Hz 20 kHz lt 2 dB 60 Hz 18 kHz lt 0 5 dB 32 44 1 48 kHz 1xF Type IEC169 24 Female 950 2150 MHz 75 Ohm unbalanced 75 to 25 dBm 13 18 V DC 5 Max 0 5 A max overload protected DiSEqC Versions System amp Memory CPU Flash Memory System Memory 1 0 1 1 1 2 GOTO X Tone Burst STi7111 8 MBytes 256 MBytes STRONG DIGITAL TV www strong tv 19 STRONG PART 1 English DIGITAL TV Connectors SAT IN SAT OUT TV SCART RGB CVBS Audio L R Output with volume control HDMI V A Output Type A Version 1 0 HDCP 1 1 RCA Output Audio L R amp Video Output S PDIF Out Coaxial Optical IR Extender input USB 2 0 Type A Connector General Data Input Voltage Range Power Consumption Power consumption in stand by Operating Temperature Storage Temperature Operating Humidity Range Size W x H x D in mm Weight 100 240 V AC 50 60 Hz max 20 W typ 7 1 W without external device 0 8
3. Use this function to set your own personal PIN code Highlight Change PIN Code with A W and press OK to advance A banner with three fields pops up Enter your old PIN at PIN Code Default PIN 0000 Enter your new PIN at Enter New and again at Reconfirm A successful change of PIN is confirmed by an on screen message Use EXIT to go back to the previous menu Once all settings are made press EXIT to leave the Parental Control menu A confirmation banner will be shown Press OK to save your settings or EXIT to discard 7 2 5 OSD Display This menu allows you to set the OSD On Screen Display functionality of your receiver according to your wishes Use V to highlight the setting you wish to change and lt P or 0 9 to change the value of the highlighted setting Press OK for a list with all available options for the chosen setting Banner Show When set to On the info banner displaying channel name channel number and Now Next information will be shown every time you change channels To disable the banner set this item to Off Banner time sec defines the time after which the OSD banners time out Possible settings are 1 10 seconds Transparency Defines how transparent the On Screen Display and banners are Possible settings are 096 2596 5096 and 10096 Once all settings are made press EXIT to leave the OSD Display menu A confirmation banner will be shown Press OK to save your settings or EXIT to discard For d
4. 0000 Deleting editing or moving one channel only Use V to select the desired satellite and TV R to toggle between TV and radio channels Use P to move the highlight to the channel list on the right of the screen Select the channel you wish to move or edit with AV To mark the selected channel for deletion press RED Press RED again to unmark the channel Press OK to lock the selected channel One more press on OK will unlock the channel again To move a channel to another position on the channel list press YELLOW Now use the keys to select a new location for the chosen channel Press OK to confirm the move To rename a channel press BLUE A banner showing a keyboard will now be displayed Use AW lt P to navigate and OK to input the chosen character Once finished press GREEN to save the changes or EXIT to quit without saving 7 3 2 Favourite Your new receiver allows you to store channels in up to 8 favourite lists Due to the large number of channels available on satellite nowadays this can be a very useful function Use TV R to toggle between TV and radio channels Select the channel you wish to add to a group with A Now select the group you wish to add the channel to with FAV Press the FAV button multiple times to move through all available favourite groups The following groups are available News Movie Music Sport Education Life Child and Leisure Press OK to place the highlighted channel in the selected favourite
5. 2 System Setup Here you can set the Country Aspect Ratio Conversion Mode and Subtitle Language Use AW to move the highlight and lt P to change settings To see a list of all possible settings for the highlighted option press OK Once all settings are made move the highlight to NEXT and press OK to continue 4 3 Satellite Selection Use V to highlight the satellite your dish is aimed at and press OK to confirm If your dish is aimed at Astra 1C TF select ASTRA 19 2 The SCAN MODE screen will appear If your dish is aimed at HOT BIRD select HOTBIRD 13E The SCAN MODE screen will appear If your dish is aimed at another satellite select OTHER You will be guided to the Satellite Settings menu Refer to chapter 7 1 1 for instructions Note If Germany is chosen as country and ASTRA 19 2E as satellite German pre installed channels are available An extra screen will then be displayed giving a choice between Preinstalled amp Scan and Satellite Scanning Choose Preinstalled at Scan to install the German pre installed channels and continue with the Setup Wizard as described from point 4 4 or choose Satellite Scanning to continue without pre installed channels 4 4 Scan Mode Use A V to highlight the desired option and press OK to confirm All Will scan all available channels on the chosen satellite Free Will scan FTA Free To Air channels only 4 5 Signal Adjust This screen allows you to fine tune the alignment of you
6. 6 5 Subtitles Some channels support a choice of different DVB subtitle languages Press SUB in viewing mode to display a list of available subtitle languages 6 6 Changing the video format To change the video format while watching TV simply press the V F key in viewing mode A list with available HDMI resolutions will pop up Select the desired resolution using AV It is also possible to change the Aspect Ratio or Conversion Mode from the Video Format banner Use the lt buttons to select the option of choice and use V to change to the setting Once all settings are made press OK to apply 6 7 EPG Electronic Programme Guide The Electronic Programme Guide is a very useful function that allows you to watch programme schedules and information on screen and to mark programs for recording Use AW to select the desired channel and to move the highlight to the program list In the program list use V to select or scroll through programs Use OK to display detailed information about the selected program Use RED to display program information for the next day and GREEN to get back one day Simply press YELLOW to get back to today s information Note Availability of EPG data depends on broadcast 8 www strong tv PART 1 English STRONG DIGITAL TV Booking a program from EPG Select a program as described above Once the desired program is selected press BLUE This will lead you to the timer menu All details are alread
7. BLUE Follow the directions on screen This function requires a correctly formatted USB storage device to be connected to the receiver Software upgrade The software files should be placed in the root directory of the device Connect the USB device to the receiver and enter USB update An attention banner will now be displayed Press OK to start the update WARNING NEVER power off the receiver or remove the USB device during the software update process Doing so might cause irreparable damage to your receiver and will void your warranty 7 4 3 OTA The OTA Over the Air function allows you to search for software updates available on satellite Please ask your local Strong dealer or visit our website for according information In the OTA menu make all necessary settings Satellite Frequency Polarisation and Symbolrate and press GREEN to start the update process WARNING NEVER power off the receiver or pull the mains plug during the software upgrade process Doing so might cause irreparable damage to your receiver and will void your warranty 7 4 4 Factory Reset A factory reset will restore your receiver to the factory default settings To reset the receiver you have to enter your PIN code Default PIN 0000 After the reset the receiver will start up in the Setup Wizard WARNING A factory reset will permanently delete all your personal settings timers and stored channels Please consider this before you perform a fact
8. It consists of the following sub menus Installation Setup Channel Advanced and Games Use to select sub menu and A V to choose an option Press OK to advance to the chosen submenu Press MENU in viewing mode to display the Main Menu 7 1 Installation The installation menu allows you to change satellite settings and to search for channels It consists of the following sub menus Satellite Settings Auto Scan Manual Scan and Satellite Edit Choose the desired sub menu with and press OK to advance 7 1 1 Satellite Settings Use this menu to change the settings for a given satellite and to configure the parameters for the used antenna Use A V to highlight Satellite and lt P to set the satellite you wish to change the settings for To see list with all available satellites press OK when the highlight is on Satellite Use A to highlight www strong tv 9 STRONG PART 1 English DIGITAL TV Transponder and gt to set the desired transponder Signal bars indicating signal quality and strength can be found on the bottom of the screen These bars show the signal conditions for the chosen satellite and transponder You can now adjust the following settings LNB type LO Frequency LNB power Band 22 kHz Switch Type Switch Input Dish Mode and Dish Position Once all settings are made press EXIT to get to the previous menu or use AY to highlight To and lt P to select Auto Scan or Manual Scan to advance to
9. STRONG Digital High Definition Satellite Receiver SRT 7100 DIGITAL TV Picture similar STRONG User Manual www strong tv RONG SS Fig 1 Fig 2 Oooo CACAD oooo 59006 0000W 6 GDie STRONG IGTALTV Fig 3 Fig 4 Fig 6 TELEVISION SCART OFI AC 190 240V 50 60 20W lodel SRT 7100 Digital High Definition Satellite Receiver Supplied by STRONG amp Co Japan COAXIAL SIPDIF TELEVISION OFF CAUTION 100 240V 50 80Hz Max 20W A Model SRT 7100 Digital High Definition Satellite Receiver TV SCART Homi Supplied by STRONG amp Co Japan SIPDIF iSEqC Switch A OFF CAUTION AC 100 240V 50 60 Max 20W COAXIAL Model SRT 7100 Digital High Definition Satellite Receiver SIPDIF Supplied by STRONG amp Co Japan PART 1 English STRONG DIGITAL TV TABLE OF CONTENTS 1 0 INTRODUCTION 1 1 Safety Instructions 1 2 Storage 1 3 Equipment Set up 1 4 Accessories 1 5 Usage of external USB devices 2 0 YOUR RECEIVER 2 1 DEFAULT PIN CODE 0000 2 2 Front Panel 2 3 Rear Panel 2 4 Remote Control Unit 3 0 CONNECTIONS 3 1 Basic connection using a Scart cable 3 2 Basic connection using an HDMI cable 3 3 C
10. consult a professional installer to set up your equipment Otherwise please follow the instructions below Refer to the user manual of your TV and your antenna Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver The following symbols will serve as follow WARNING Indicates warning information Tips Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Bold Character Move to Represents a menu item within a window Italic Character 1 4 Accessories m User s Manual 1 Remote control unit m IR Extender m 2x Batteries AAA type Note The batteries should not be recharged disassembled electrically short circuited be mixed or used with other types of batteries 1 5 Usage of external USB devices It is recommended to use USB 2 0 storage devices If your device is not compatible to USB 2 0 specifications recording playback and other multimedia functions of the receiver would not work properly STRONG cannot guarantee compatibility to all types of USB storage devices It is advised not to store important information on USB storage devices used with the receiver Always make backups of data on your USB storage device before using it with this receiver STRONG will not take responsibility for any l
11. receiver due to high voltage currents and possible electrical hazards and your warranty will be void Refer all maintenance or servicing to suitably qualified personnel m When you are connecting cables be sure that the receiver is disconnected from the mains supply voltage Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment m It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver m If the receiver does not operate normally even after strictly following the instructions in this user manual it is recommended to consult your dealer 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children For transporting the receiver from one place to another or if you are returning it under warranty conditions make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 2 www strong tv PART 1 English STRONG DIGITAL TV 1 3 Equipment Set up We recommend you
12. to change and lt P to change the value of the highlighted setting Press OK for a list with all available options for the chosen setting Display This setting affects the menu language of your receiver All menu s and messages will be displayed in this language Audio is the preferred audio language The receiver will automatically switch audio to the preferred language whenever available Subtitle Whenever available subtitles will be displayed in the selected language Country Here you can set your country of residence www strong tv n STRONG PART 1 English DIGITAL TV Once all settings are made press EXIT to leave the Language menu A confirmation banner will be shown Press OK to save your settings or EXIT to discard 7 2 2 Output Options This is the menu to configure the audio and video outputs of your receiver Use V to highlight the setting you wish to change and lt P to change the value of the highlighted setting Press OK for a list with all available options for the chosen setting TV Standard Set the standard corresponding to your TV set Available options are Auto NTSC PAL and SECAM Aspect Ratio Use this option to set the aspect ratio of your TV set Available options are 4 3 and 16 9 Conversion mode Use this option to set the preferred way of converting 16 9 broadcasts to 4 3 TV format You can choose between the following options Letter box the full 16 9 picture will be displayed on
13. your 4 3 TV set with black bars above and below the picture Pan and scan The centre of the 16 9 picture will be displayed full screen on your 4 3 TV and Combined Combination of Letter box and Pan and scan SCART Mode Select RGB for the best picture quality or CVBS in case your TV doesn t support RGB Digital Audio Defines the format available on the S PDIF output of your receiver When set to PCM the digital output will always output PCM stereo regardless of the broadcasted audio format The Auto setting will pass all incoming digital audio through the digital output Use this option if you have your receiver connected to a digital surround amplifier The digital output can be switched off by setting Digital Audio to Off Video Format This setting is only active when the receiver is connected to the TV set via HDMI It allows you to set the preferred HDMI screen resolution Available options depend from your TV set Once all settings are made press EXIT to leave the Output Options menu A confirmation banner will be shown Press OK to save your settings or EXIT to discard 7 2 3 Time Setting This menu allows you to set the way the receiver collects and adjusts the time You can also adjust the Auto Power Down function here Use A V to highlight the setting you wish to change and lt P or 0 9 to change the value of the highlighted setting Press OK for a list with all available options for the chosen setting Time Display Defines wh
14. 3 W without external device 0 40 C 10 70 C 25 75 RH non condensing 230 x 165 x 44 0 79 kg 20 www strong tv 15 Apr 2010 19 18
15. Auto Scan or Manual Scan A confirmation banner will now be displayed Press OK to confirm the made changes or EXIT to discard 7 1 2 Auto Scan Use this menu to perform an automatic channel search on one or more satellites On the left of the screen a list with satellites is displayed Use V to highlight the satellite s you wish to scan and press OK to mark the highlighted satellite Press OK again to unmark a marked satellite Note you can mark multiple satellites Auto Scan will search all marked satellites for available channels Now select the desired scanning options on the right ofthe screen Use A V to highlight and OK to set an option Scan Mode All scan all channels Free scan Free To Air channels only Scrambled scan scrambled channels only Service Type All scan TV and Radio channels TV scan TV channels only Radio scan radio channels only Network Search Disabled no network search Enabled network search will be performed Once all settings are made press the GREEN button on the remote control to start the scan or EXIT to quit without scanning All newly found channels will be stored at the end of the channel list Tip Network Search If Disabled is selected the receiver will search only for channels available from the preset transponder list of the selected satellite If it is set to Enabled the receiver will perform an additional search for channels from the NIT table NIT Network Identific
16. DiSEqC 1 0 switch to the SAT IN connector on your receiver C Refer to section 3 1 or 3 2 for TV and mains connections 3 4 Connecting and using the IR extender The included IR extender allows you to place the receiver out of sight e g in a closed cabinet while still being able to control it Plug the IR extender into the IR connector on the back of the receiver Locate the extender on a position giving it direct sight to the remote control Once a suitable location is found remove the protecting foil from the adhesive tape on the back of the extender and fix it by slightly pressing it down on the surface it should be placed on www strong tv 5 STRONG PART 1 English DIGITAL TV 4 0 STARTING UP FOR THE FIRST TIME Ensure that your satellite signal is of good quality and that all connections are sound In case of difficulties or questions please ask you local dealer for assistance It is recommended to follow the Setup Wizard step by step It will guide you through the basic installation and channel searching process You can enjoy digital HD broadcasts within just a few minutes 4 1 Language selection After turning on the power for the first time the language selection menu will appear Choose your language with and confirm with OK A welcome screen will now be displayed Once you are ready press OK to start the wizard During any stage of the Setup Wizard you can press EXIT to get back to the previous screen 4
17. ation Table Use this option to receive new launched channels from the selected satellite 7 1 3 Manual Scan Use this menu to scan a single transponder only The following can be set Satellite Transponder Frequency Polarisation Symbolrate Scan Mode Service Type and Network search Use AW to move the highlight to the chosen setting and lt P to change its value Once all settings set correct press the GREEN button to start scanning or EXIT to quit All newly found channels will be stored at the end of the channel list 10 www strong tv PART 1 English STRONG DIGITAL TV Note Press YELLOW in the Manual Scan menu to make settings for a PID search Scan mode Service type and Network search will then be replaced by settings for Video PID Audio PID and PCR PID For information on PID values please visit websites like www lyngsat com or www kingofsat net 7 1 4 Satellite Edit Here you can edit transponder data or add a new satellite On the left of the screen a list with all available satellites is displayed The right of the screen displays a list will all available transponders for the highlighted satellite Adding or editing a transponder Use A V to highlight the desired satellite Press to move the highlight to the transponder list Press YELLOW to add a transponder or use AY to highlight the transponder to be edited and then press BLUE to enter the edit screen Use V to navigate in the edit screen and use
18. en the front panel display will show the clock Possible settings are Off and Stand by only Use GMT On the receiver will use broadcast time Use the Time Zone setting to define the deviation from GMT time Summer Time can be set to On or Off Use GMT Off Allows you to enter the time settings manually Use the 0 9 buttons to set the current time in the Local Time option Use A V to move the highlight to Local Date and press OK A calendar will be displayed Use A gt to select the actual date and press GREEN to confirm 12 www strong tv PART 1 English STRONG DIGITAL TV Auto power down Auto Power Down is a new power saving feature that helps you with reducing power consumption It will switch off the receiver when no command is given for at least the set time Possible settings are 1 6 hours with one hour steps and Disabled Once all settings are made press EXIT to leave the Time Setting menu A confirmation banner will be shown Press OK to save your settings or EXIT to discard 7 2 4 Parental Control In this menu you can enable or disable the menu lock function and change the PIN code Use A V to highlight the setting you wish to change and lt P 0 9 to change the value of the highlighted setting Menu Lock If Menu Lock is set to Enabled items in the Main Menu are only accessible after entering the PIN Default PIN 0000 When set to Disabled all menu items are freely accessible Change PIN Code
19. et a timed recording Channel Press OK to display the channel list and use A to select the channel that the receiver should use for the timed action Duration Use the 0 9 buttons to digit the duration of the timer Once all settings are made press EXIT to leave the menu A confirmation banner will be shown Press OK to save the timer or EXIT to discard Deleting a timer In order to delete a set timer select it with V and press RED A confirmation banner will now be shown Press OK to delete or EXIT to cancel Note In case one timer is in conflict with another or ifthe set time has already passed the receiver will display a warning and asks you how to solve the conflict 7 4 Advanced This sub menu gives you access to advanced functions such as updating and factory reset The following options are available System Info USB Update OTA and Factory Reset 7 4 1 System Info Displays valuable information about the software and hardware version of your receiver and our web address www strong tv customer support agent might ask for the information given in this screen Press EXIT to leave the System Info screen 7 4 2 USB Update This function allows you to perform a system upgrade from an USB device You can also use it to export your channel list to a connected USB device 16 www strong tv PART 1 English STRONG DIGITAL TV Exporting channel data To export all channel data enter USB Update and press
20. etailed information about the Info banner please refer to chapter 6 2 Info Banner 7 3 Channel Within this menu you can manage channels and configure favourites play files from a connected USB storage device and to set timers The Channel menu consists of the following sub menus Sort and Edit Favourite File Explorer and Timer Choose the desired sub menu with A and press OK to advance www strong tv 13 STRONG PART 1 English DIGITAL TV 7 3 1 Sort and Edit Use this menu to manage channels in the channel list Set the satellite you wish to manage channels on in the left column Select All Sat to display the channel list with channels from all installed satellites Sorting a channel list Use V to select the desired satellite and TV R to toggle between TV and radio channels Press YELLOW to display the Sort in Order banner Use to select the sorting method of your choice and OK to confirm Un locking or deleting all channels in the current list Use A V to select the desired satellite and TV R to toggle between TV and radio channels To delete all channels in the chosen list press RED All channels in the chosen list will be marked for deletion Press GREEN to confirm this action To lock all channels in the chosen list press OK All channels in the chosen list will be marked as locked Press GREEN to confirm this action Locked channels can only be accessed after entering the correct PIN code Default PIN
21. evice STRONG will not take any responsibility for damaged or lost data on the USB device Please make a backup copy of important data on your USB device before using it with your receiver Playback of previously recorded programs All recorded programs will be placed in the DVR folder on your USB device Open this folder as described above and select the desired recording Press OK to start playback The following functions are available during playback Press 1 to pause the playback Press Il again to resume playback Use and for fast forward or fast rewind playback Press EXIT or to get back to the File Explorer Viewing photos Your receiver allows you to watch a slide show with all photo s available in the chosen folder To use the slide show choose a folder with photo files Press YELLOW to open the slide show settings window Here you can adjust the Transition mode and Duration To disable the slideshow mode set Duration to Disabled Once all settings are made press GREEN to save and exit the Slideshow settings banner Select the desired Photo file and press OK to view Press EXIT to get back to the File Explorer Listening to MP3 music Select the desired MP3 file and press OK to start playback During playback the following functions are available 4 starts playback of the next MP3 starts playback of the previous MP3 a stops playback shuffle All files in the directory will be played back in random order g
22. group To remove a channel from a group use A V gt to highlight the desired channel in the group and press OK Once all settings are made press EXIT to leave the menu A confirmation banner will be shown Press OK to save your settings or EXIT to discard Note Removing a channel from a favourite group doesn t remove the channel from the channel list 7 3 3 File Explorer The File Explorer can be used for the playback of previously recorded programs to show photos or for playing MP3 music files 14 www strong tv PART 1 English STRONG DIGITAL TV When the File Explorer is opened the name of your connected USB device will be shown on the right side of the window Press OK or P to access the USB device The content of the device will now be displayed Only files suitable for playback on your receiver will be displayed Use A V to select a file or folder Press OK to start playback or to open the selected folder To get back to the previous folder use EXIT or 4 Alternatively you can also select the folder marked with two points and press OK To format the connected USB device press the YELLOW button when in the root folder of the connected device Please note that the format function will only work on Hard Disk Drives Before disconnecting your USB device please press the GREEN button to Safely remove USB device WARNING The Format function will delete all records data and information from your USB d
23. hts reserved 04 2010 I 1 10826 029 928 www strong tv 1 STRONG PART 1 English DIGITAL TV 1 0 INTRODUCTION 1 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER In a closed or poorly ventilated cabinet directly on top of or under any other equipment on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES m To direct sunlight or any other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects such as loudspeakers transformers etc Do not use a damaged power cord It may cause a fire or an electrical shock Do not touch a power cord with wet hands It may cause an electric shock m When the receiver is not used for a long period of time you should unplug the power cord from the wall socket Do not use alcohol or ammonia based liquids to clean the receiver If you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside SAFETY PRECAUTIONS Never open the receiver cover It is dangerous to touch the inside of the
24. lect the first letter of the desired channel and OK to confirm All channels beginning with the chosen letter will now be displayed www strong tv 7 STRONG PART 1 English DIGITAL TV The following keys are available in the Channel list and viewing mode TV R Toggles between TV and radio channels SAT changes the satellite FAV to switch to one of the available favourite lists 6 1 3 Using the keys P or A will switch to a higher channel P or V will switch a lower channel 6 2 Info Banner At any time during viewing mode you can press the INFO button to get info about the current channel and program Press INFO twice to see technical details about the current channel Program information is displayed when available Availability depends from broadcast 6 3 Selection of audio language Some channels support a choice of different audio formats and or languages To select another audio stream press AUDIO in viewing mode A list with available audio streams will now be displayed Use AY to select the desired stream and confirm with OK 6 4 Teletext Your receiver includes a fully featured Teletext To access Teletext press the BLUE button in viewing mode and use the 0 9 buttons to input the number of the page you wish to see The coloured buttons of the remote control allow you to jump to selected pages directly as indicated on the bottom of the teletext screen Press EXIT to go back to viewing mode
25. mes the current broadcast 20 YELLOW SUB Displays a list of available subtitling for the current channel 21 BLUE TEXT Displays the teletext browser 22 M Freezes resumes the playback of recordings or music files 23 4 Jumps to the previous track during MP3 playback 24 Jumps to the next track during MP playback 25 e Starts recording of the current broadcast 26 Starts playback of the selected file in File Explorer 27 Fast forward 28 Fast rewind 29 M Stop 3 0 CONNECTIONS 3 1 Basic connection using a Scart cable Fig 4 A Connect the LNB of your satellite dish to the SAT IN connector of your receiver using a good quality coax cable and suitable F connector plugs B Connect one end of a good quality Scart cable to the TV SCART connector on your receiver and the other end to the SCART input of your TV Plug the power cord to a suitable wall outlet 3 2 Basic connection using an HDMI cable Fig 5 A Connect the LNB of your satellite dish to the SAT IN connector of your receiver using a good quality coax cable and suitable F connector plugs B Connect one end of a good quality HDMI cable to the HDMI output on your receiver and the other end to the HDMI input of your TV C Plug the power cord to a suitable wall outlet 3 3 Connecting multiple fixed dishes using a DiSEqC 1 0 switch Fig 6 A Connect the LNB s of your fixed dishes to the inputs of a DiSEqC 1 0 switch B Connect the output or to receiver connector of the
26. ng direction of the dish The remote control The batteries of the remote control does not work exhausted The receiver can t receive the signal are not inserted wrongly inserted or Check the antenna cable replace the cable or connect the cable to the receiver tightly Set the values of tuner parameters correctly in menu Installation Satellite Settings Check the signal strength with a spectrum analyzer and adjust your dish correctly Check whether the batteries are inserted correctly or exhausted if so replace the batteries in the remote control The USB storage device Wrong formatted Format USB device by receiver in is not working properly menu Channel gt File Explorer The external USB Power consumption is too high Connect an extra power supply HDD does not start adapter to your USB HDD device Auto Power Down function is activated and reached the adjusted time default 3h The receiver switches to STBY automatically In the menu Setup Time Setting you can adjust the Auto Power Down time or disable it 18 www strong tv PART 1 English 9 0 SPECIFICATIONS Demodulator Demodulation Input Symbol Rate DVB S2 8PSK QPSK FEC Decoder Video Decoder Profile Level Input Rate Aspect Ratio Frame Rate Video Resolution Audio Decoder Audio Decoding Audio Mode Frequency Response Sampling Rate Tuner Connector Input Frequency Rage RF Impedance Signal Level
27. onnecting multiple fixed dishes using a DiSEqC 1 0 switch 3 4 Connecting and using the IR extender 4 0 STARTING UP FOR THE FIRST TIME 4 1 Language selection 4 2 System Setup 4 3 Satellite Selection 4 4 Scan Mode 4 5 Signal Adjust 4 6 Channel Setup 5 0 QUICK GUIDE TO USING YOUR RECEIVER 6 0 OPERATION 6 1 Changing channels 6 2 Info Banner 6 3 Selection of audio language 6 4 Teletext 6 5 Subtitles 6 6 Changing the video format 6 7 EPG Electronic Programme Guide 6 8 Instant Recording 6 9 Timeshift 7 0 MAIN MENU 000000 00 00 00 4000000 ARA 0 UO UJ C9 C9 C9 NO NO NJ 7 1 Installation 9 7 2 Setup 11 7 3 Channel 13 7 4 Advanced 16 7 5 Games 17 8 0 TROUBLESHOOTING 17 9 0 SPECIFICATIONS 19 STRONG declares that this item complies with the basic requirements and other relevant regulations of Ld 01 80 501 49 91 em directives CE 2004 108 EEC and 73 23EEC RoHS 2002 95 2 0 42 Min max fror Subject to alterations In consequence of continuous research and development technical specifications x is design and appearance of products may change ASTRA is a registered trade mark of SES ASTRA LE 0820 400 150 Eutelsat and HOT BIRD are registered trademarks of Eutelsat Communications all other product names O 0 12 Min from Austrian wired line trademarks or registered trademarks of their respective owners ve STRONG 2010 All rig
28. ory reset 7 5 Games Your receiver is equipped with 4 games To play a game select one of the four available games Sudoku Tetris Snake or Box and press OK to enter the game Please follow the directions on screen 8 0 TROUBLESHOOTING There may be various reasons for abnormal operation of the receiver Please check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact your local Serviceline or STRONG dealer Alternatively you can send a support mail via our website www strong tv NEVER open or disassemble your receiver This may cause a dangerous situation and will void the warranty www strong tv 17 STRONG PART 1 English DIGITAL TV The display on front panel does not light up The power cord is not plugged in Receiver switched to STBY and the display function is switched OFF Wrong connection or setting of the Audio Video output of the receiver to TV No picture or sound Check that the power cord is plugged in to the wall outlet Make sure power switch on rear panel is in ON position Check if receiver is in STBY and the setting within the menu Setup gt Time Setting gt Time Display is set to OFF Connect the Audio Video output of the receiver to TV correctly and check the adjusted settings in the menu Setup gt Output Options Press the MUTE button PTUS No picture Incorrect values of some tuner parameters Wro
29. oss of information or circumstances caused by loss of information Please ensure that either the USB device is already formatted to FAT FAT32 or format the USB device via your receiver refer to chapter 7 3 3 File Explorer for details 2 0 YOUR RECEIVER 2 1 DEFAULT PIN CODE 0000 2 2 Front Panel Fig 1 1 Standby ON switch turns the receiver ON or to Standby 2 USB connector connect your USB device stick HDD etc to this port 3 4digit LED display displays channel number or time depending on settings www strong tv 3 STRONG PART 1 English DIGITAL TV 2 3 Rear Panel Js SAT IN SAT OUT IR AUDIO L R S PDIF VIDEO RCA TV SCART HDMI Power switch 0 Power cord 2 4 Remote Control Unit 10 12 13 14 15 16 EA 18 e 0 9 SAT TV R MENU EXIT AY 4 OK FAV EPG V V INFO AUDIO P P RED RCL Fig 2 To connect to the LNB of your satellite dish for reception of satellite broadcast signal To loop through the satellite signal to a second receiver To connect the IR extender To connect to the audio input of your HIFI or television To connect to a digital or home cinema audio amplifier To connect to the RCA video input of your TV or VCR using an RCA cable To connect to TV using a SCART cable To connect to the HDMI input of your TV using a good quality HDMI cable To switch the mains power ON or OFF The receiver req
30. r dish antenna for optimum reception Use lt P to select the switch input the dish is connected to If the LNB of your dish is directly connected to the receiver choose Switch Input 1 The bars on the bottom of the screen indicate the current signal strength and quality A red bar indicates a bad signal Green bars indicate a good signal Yellow bars indicate that the signal condition is nearly acceptable Adjust your dish for maximum possible signal quality and strength Once the signal cannot be improved anymore fix the dish on this position and press OK to continue 6 www strong tv PART 1 English STRONG DIGITAL TV 4 6 Channel Setup Your receiver will now perform an automatic channel search Once the process is finished all found channels will be stored and the receiver will switch to the first found channel You are now ready to enjoy your new receiver Note If no channels were found during the automatic channel scan the receiver will display the Satellite Settings menu Please refer to chapter 7 1 1 for instructions 5 0 QUICK GUIDE TO USING YOUR RECEIVER We at STRONG understand that you can t wait to enjoy your new HD receiver The following quick guide will make you familiar with the basic operation of this device We do however advice you to read the full manual to get the best performance from your STRONG HD receiver To turn your receiver ON or to Standby use the button on the remote control or
31. t gt repeat Press once for single track repeat or twice to repeat all files To exit the file explorer Use EXIT to get back to the Root directory of your USB device Press EXIT once more to leave the File Explorer Note Please consider that File Explorer needs a correctly formatted USB device in order to work with your receiver www strong tv 15 STRONG PART 1 English DIGITAL TV Playback of MP3 music will continue as long as the File Explorer is active This allows you to listen to MP3 music while watching photos Tip The File Explorer will only show files when a correctly formatted USB device is connected to the receiver 7 3 4 Timer Timers can be used to schedule recordings or to switch to a certain channel at a desired moment It will help you not to miss your favourite events Use A V to select one ofthe eight available timers Press OK to advance The Edit Timer screen will now be displayed Use to switch between settings and lt P or 0 9 to adjust the value of a setting Cycle Choose between Once Everyday or Weekly Date With Cycle set to Once press OK to display the calendar Use A to pick the date for the recording and confirm with OK With Cycle set to Weekly Use lt P to select the day of the week at which the timer will start Time Use the 0 9 buttons to enter the time at which the timer will start Action Use lt P to choose between Play or Record Select Record to s
32. the button on the left side of the front panel Choose the desired channel with the Y buttons or the P P buttons Alternatively you can digit the channel number with the 0 9 buttons on the remote control Or press OK in viewing mode to display the channel list The volume can be adjusted with the V V buttons or the lt P buttons 6 0 OPERATION In viewing mode several features are available to make watching TV a true pleasure This paragraph describes these features Please also read chapter 7 0 to get familiar with the menu of your new receiver 6 1 Changing channels Your new receiver is equipped with three ways to change channels m via direct access a via the channel list and m via the P P keys 6 1 1 Direct access To gain direct access to a certain channel simply input its number with the 0 9 key s on the remote control Channel numbers can be up to four digits long Entering a number with less than four digits is possible Just wait a few seconds and your receiver will switch to the selected channel 6 1 2 Channel list Press OK in viewing mode to display the Channel List Use A V in the Channel List to highlight your channel of choice and press OK once to select the highlighted channel Press OK again to leave the Channel List The Channel List is equipped with a filter function to make finding your favourite channels easier While in the Channel List press RED An alphabet banner will now be displayed Use A V to se
33. uires a mains voltage of 100 240V AC 50 60Hz auto selecting Please check the local power conditions before connecting the receiver to the mains supply Fig 3 Turns the receiver ON Standby Mutes the audio output of the receiver Channel number and numeric value input Satellite selection in normal viewing and channel mode Toggles between TV and Radio mode Displays the menu in viewing mode or to go back one step in the menu Go back one step in the menu cancellation of current process exit from main menu to viewing mode Switches to the next previous channel in viewing mode or moving the highlight up down in the menu Increasing decreasing of the volume level in viewing mode or changing values of settings in the menu Viewing mode Displays the channel list Menu activation of the highlighted item Toggles between available favourite groups and all channels list Displays the EPG Electronic Program Guide Increasing decreasing of the volume level Viewing mode Press once to display channel number name and now next info Press twice to display frequency signal strength information Displays the audio selection menu with selections for available languages and audio modes Toggles between available HDMI screen resolutions Switches to next previous channel in viewing mode Toggles between the current channel and the previous channel in viewing mode www strong tv PART 1 English STRONG DIGITAL TV 19 GREEN PAUSE Freezes resu
34. y filled in for you Make a choice between Play or Record action and save the timer Please refer to section 7 3 4 for details 6 8 Instant Recording Your new receiver allows you to make an instant recording of the program you are watching Simply press to start the recording To enter the duration for the recording press again Use the 0 9 keys to input the desired recording time During the recording a banner showing the elapsed recording time will be shown on the upper right of your TV screen To stop the recording press Please connect an USB storage device with sufficient free space before you start a recording For recording HD broadcast a high speed device is needed 6 9 Timeshift The Timeshift function allows you to pause live broadcasts and resume normal watching without missing anything Press II to freeze the current broadcast Press II again to start time shifted playback To stop Timeshift press Note The Timeshift will only work correctly when a fast USB storage device such as an USB2 0 HDD is connected to the receiver Distorted picture and or audio during Timeshift indicate a low USB device speed STRONG cannot guarantee for USB devices used Especially when Timeshift is activated at channels with high data rate High quality SD HD STRONG cannot guarantee an accurate Playback of the Timeshift file 7 0 MAIN MENU All important settings and features of your receiver can be operated from the Main Menu
Download Pdf Manuals
Related Search