Energy Sistem Linnker 5000
Contents
1. DC Input Button 2 1 Assemble and disassemble the ear hook with the Headset 1 To assemble the ear hook with the Headset push the toggle of the ear phone into the pin hole of the ear hook To disassemble the ear hook with the Headset just turn and pull out the toggle of the ear phone from the pin hole of the ear hook Please refer to Fig 1 2 Fit the ear hook with your right or left ear Please refer to Fig 2 Fig3 Fig4 and Fig 5 Push Pull and Turn Fit the Left Ear ew S552 Fig 1 Fig 2 Fig 3 Fig 4 Fig 5 2 Charging the battery 1 The Plug the travel charger into the AC outlet and then connect the charger into the DC input of the headset The red indicator of the headset will light on When the battery is full the red MONS indicator will be off Disconnect the adaptor from the headset When the battery is new it is not fully charged It takes nearly 4 hours to fully charge the battery Afterwards it will take nearly 2 hours to fully charge the battery 2 If there is a USB charging cable included optional you can charge the headset with the USB charging cable Please plug one end of USB charging cable to USB slot of your Fig 6 computer another end to DC input of the headset The following is the same with the travel charger Please refer to Fig 6 3 Turning the headset on or off 1 Press the Button 1 for nearly 3 seconds You will hear two beep sou2. or ending calls When the headset is paired with your phone and when there is an incoming call you will hear a musical ring Then press the Button 1 to answer the call When there is a call in session you can press the Button 1 to end the call Note Because of the different design of some mobile phones a disconnection may automatically happen even when the headset 1s powered on In this case the headset will not ring if there is an incoming call Press Button 1 for 1 second to re connect the headset with the mobile phone for an incoming call Please refer to Fig 10 Re connect Fig 10 6 Making calls 1 Voice dialing Press the Button 1 After hearing a beep sound say the name of the person you recorded on your phone The availability of this function depends on the design of the mobile phone you use Please refer to the manual of your mobile phone for the voice dialing function 2 Dial the phone number on you mobile phone as you normally do The sound will be transmitted to the headset automatically 7 Changing the volume of the Headset 1 Press the Button 2 to increase the listening volume of the headset 2 Press the Button 3 to decrease the listening volume of the headset 3 You can also adjust the volume from your mobile phone Please refer to the manual of your mobile phone 8 Redialing the call After ending the call you can press the Button 2 to redial the
3. call you just ended The availability of this function depends on the design of the mobile phone you use Please refer to the manual of your mobile phone 9 Mute function You may have to keep a call on line while talking to others Push the Button 2 and the Button 3 at the same time for one second You will hear continuous beep sounds Now the headset is in Mute function mode To disable the Mute function press the Button 2 and the Button 3 at the same time once again 10 Rejecting a call When there is a call in session you can press the Button 1 for three seconds to reject a call Function of Buttons Button 1 Turning on or turning off the headset Pairing Answering or Ending a call Voice Dialing Rejecting a call Button 2 Volume up Redial Button 3 Volume down Button 2 Button3 Mute function Trouble Shooting 1 The red indicator flashes It indicates that headset is in low battery Charge the battery until the red indicator is turned off 2 If no connection between the headset and your phone Make sure that the bluetooth headset fully charged Repeat the step 3 to complete the pairing process Make sure that the headset is within 10 meters of your phone and that there are no obstructions such as walls or other electronic device between the headset and your phone If the steps above do not solve the problem please refer to the manual of your mobile phone for more informatio
4. n Note This headset is complied with Bluetooth Specification 1 2 However the interoperability of this headset and other devices is not guaranteed because of the compatibility Product Care 1 Avoid humidity liquid or moisture as this device is not water proof 2 Avoid high and low temperature especially in a car 3 Please do not dissemble the headset 4 Please do not use chemical cleaning solvent or strong detergent to clean the headset And avoid sharp object 5 Please do not change or modify the headset Any change or modification will void the warranty of the product 6 Do not dispose the headset into a fire This may result in an explosion 7 Use only the attached charger when you charge the headset Safety instructions 1 Check local laws about the use of mobile phone and headset while driving For your own Safety please focus on the road while using the headset 2 Please turn off the headset according to the sign of the specified areas that requires an electric device to be switch off These areas include the hospital aircraft and blasting area or potentially explosive atmosphere 3 Do not store the headset in the air bag deployment area This may result in an injury when the air bag deploys 4 Do not dissemble the charger It may expose you to the danger of electric shock Caution and Warranty Read the following information before using this device Users are not permitted to change or modify this device Any unap
5. nds and the blue indicator will begin to flash The headset is now powered on 2 When the power is on press the Button 1 for 3 seconds You will hear two beep sounds and the red indicator will flash Now the headset is turned off Please refer to Fig 7 and Fig 8 Fig 7 Fig 8 4 Pairing the headset 1 The headset must be powered off before you begin to initiate the pairing Press the Button 1 till the blue and red indicators begin to flash alternatively The headset is now in pairing mode 2 Initiate the pairing process of your bluetooth mobile phone Please refer to the manual of your mobile phone 3 When asked the PIN code please enter 0000 to successfully complete the pairing process 4 When the pairing process is successfully completed the blue indicator will flash The headset is now in standby mode 5 After the headset is successfully paired with your mobile aa phone In some case you will still have to connect the headset 4 Pairing with your mobile phone Please refer to the mobile phone manual Please refer to Fig 9 Fig 9 Note 1 If the headset is not in pairing mode your mobile phone can not find the headset Please set the headset into pairing mode before you start to pair the headset with your phone 2 If no pairing is possible over a period of time Aprox minute the pairing process will be stopped You have to repeat STEP 4 to successfully complete the pairing 5 Answering
6. proved change or modification by the user on this device will void the user s authority to use this device The manufacturer and dealer of this device are not responsible for any accident caused by the improper use or dissemble of this device This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation
Download Pdf Manuals
Related Search