Chief PAC511
Contents
1. Grounding lug location Figure 4 Installing Accessories Accessories can be mounted directly to the PAC511 by using the mounting screws provided and the mounting holes integrated into the box To mount an accessory 1 Identify area within accessory box where accessory is to be mounted 2 Align the mounting holes in accessory with mounting holes in box 3 Secure accessory to box using Phillips screwdriver and as many 1 8 18 x 3 4 mounting screws E as required See Figure 5 NOTE The top and bottom slots in the side flanges of PAC51 1 are designed to fall at the center of the studs on 16 centers When installing a mount over the top of PAC511 align mounting holes in mount with top and bottom slots in side flanges and secure using hardware specified in the Installation Instructions provided with the mount 4 Use the wire tie clips as necessary for cable management See Figure 5 PAC511 Installation Instructions E 8 provided Figure 5 511 Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8807 002008 Rev00 2009 Milestone AV Technologies a Duchossois Grou2. INSTALLATION INSTRUCTIONS IN WALL ACCESSORY BOX c CHIEF PAC511 Our Mounts Your Vision 511 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damag
3. cings NOTE This In Wall Cabinet System is for use with ITE or Audio Video equipment only Installation Instructions PAC511 DIMENSIONS 87 B A 3 43 1 O t 6 4 rol f M eas 28 4 e 559 406 4 965 112 S 2 2 20 16 00 362 1 54 8 14 26 2 16 0 94 7 66 7 3 73 2 63 DETAIL A ne E SCALE 1 1 i 466 7 304 8 438 2 J 18 38 12 00 22 2 i 50 88 ge f 428 6 393 7 16 88 15 50 ates ang 38 1 E 428 6 1 50 16 88 46 8 DETAIL B 159 ba al 1 84 SCALE 1 1 e 82 6 MEASUREMENTS MILLIMETERS Er 3 25 INCHES LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations C Phil
4. e to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided CAUTION This equipment must be installed and assembled by qualified service personnel in accordance with local building codes WARNING Failure to provide adequate structural strength for this accessory can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this accessory is attached can support the combined weight of the box and all equipment not to exceed 10 Ibs 4 5 kg IMPORTANT SUITABLE FOR USE IN OTHER ENVIRONMENTAL AIR SPACE IN ACCORDANCE WITH SECTION 300 22 C OF THE NATIONAL ELECTRICAL CODE NOTE The equipment shall be installed and assembled by qualified service personnel NOTE Knockouts are provided for ease of installation Any unused knockouts that have been punched are to be closed up with a metal plug NOTE The maximum specified ambient temperature of the cabinet system is 40 120 F 4 49 C NOTE Spacings Minimum spacings between the Accessories and components and the housing for Information Technology Communication Equipment shall be maintained for safe operation of the equipment when installed in accordance with the National Electric Code ANSI NFPA 70 1999 Refer to communication equipment manufacturer s specifications for minimum spa
5. ld be installed by qualified personnel PAC 511 Site Preparation Locate and Prepare Mounting Site 1 Identify a suitable wall location for the accessory IMPORTANT The PAC 511 is designed for in wall installation between two wood or steel studs 16 on center Inadequate space will remain on each side between studs for electrical wires cables plumbing ductwork or insulation Locate accordingly WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL WIRES OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before cutting drilling or installing fasteners WARNING EXPLOSION AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of gas water waste or any other plumbing before cutting drilling or installing fasteners 2 Using a stud sensor locate and mark studs 3 Center and level housing between marked studs 4 Using housing as a template draw pencil line completely around housing NOTE Housing is designed to fit between and directly against two adjacent wall studs 5 Using a measuring tool measure the marked area and compare to the dimensions below If measurements match continue to Step 6 If not adjust markings to match dimensions below See Figure 1 6 Cut drywall on outside edge of line and remo
6. lips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Perforar Drill Hole Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou 2 O O Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale 511 Installation Instructions TOOLS REQUIRED FOR INSTALLATION UM p B 22222 x 4 included r Grounding screw and washer installed at factory See Figure 4 on page 6 ng J 2 2 9 10 j exam i GY Earthing symbol IEC 60418 No 5019 affixed adjacent to grounding terminal A 1 PAC 511 e 2 7 E 8 ei 1 8 18 x 3 4 F 4 M7 x 40mm Installation Instructions PAC511 INSTALLATION The PAC 511 is intended for use in installations where an existing finished drywalled wall is present and includes flanged edges to cover the cutout in wall WARNING IMPROPER INSTALLATION CAN RESULT DEATH OR SERIOUS PERSONAL INJURY This accessory shou
7. p Company www chiefmfg com 07 09 USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA AI fp zs 27 AN AS P 486 755 8996 9226 RY 86 755 8996 9217 gt OK 12 C Asia Pacific
8. ve 511 z 14 1 2 368mm Figure 1 15 314 400mm Accessory Box Installation 1 Insert PAC511 A into opening See Figure 2 Figure 2 511 Installation Instructions WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL WIRES OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before cutting drilling or installing fasteners 2 Secure accessory box to studs by WOOD STUD 1 Drill four 3 16 dia pilot holes in studs at mounting holes See Figure 3 2 Install four M7 x 40mm Allen head connector screws F into pilot holes using an M4 Allen head drill bit D See Figure 3 STEEL STUD 1 four 3 16 dia pilot holes in studs at mounting holes See Figure 3 2 Install four 1 4 countersunk finishing washers and four 1 4 x 2 Phillips flat head self drilling screws G into pilot holes See Figure 3 re E Only x4 eo 2 Stud Only Figure 3 DANGER IMPROPER WIRING CAN LEAD DEATH OR SEVERE PERSONAL INJURY Grounding must be installed by qualified personnel using a UL Recognized No 12AWG Green and Yellow grounding wire connected to grounding lug on mount Typical
Download Pdf Manuals
Related Search