Scosche FD1428B mounting kit
Contents
1. FD23 1998 Up Ford 2003 Up Ford LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly wire harness codes and information pertaining to installation of this kit FD1428B in 2001 06 Select Ford Lincoln Mercury vehicles Scosche Industries Inc cannot be held responsible for discrepancies inconsistencies that may occur due to the automobile manufacturing changes or options or damage that may occur in the automobile during the installation of components while using this booklet If you have any further questions call our toll free technical help line at 1 800 621 3695x3 2010 SCOSCHE INDUSTRIES INC SI 7 10 FD1428B 3000516 FACTORY STEREO REMOVAL 2003 06 FORD EXPEDITION 2002 05 FORD EXPLORER 4 DR 2002 05 LINCOLN AVIATOR 2002 05 MERCURY MOUNTAINEER 1 Use panel removal tool to pry out stereo trim bezel and disconnect 2 Extract two 2 9 32 screws located below the stereo disconnect and remove PI a 2001 04 FORD MUSTANG 1 Use panel removal tool to pry out gear shift bezel 2 Use panel removal tool to pry out radio trim bezel 2 Extract two 2 9 32 screws located below the stereo disconnect and remove 2003 06 LINCOLN NAVIGATOR 1 Open the center console door and remove 1 push pin type fastener from power window switch panel Unsnap unplug and remove panel Extract 2 7mm hex screws from back of gear shift cup holder panel uns2. SCOSCTCHE IN DASH INSTALLATION KIT FOR 2001 06 SELECT FORD LINCOLN MERCURY VEHICLES FD1428B 1525 REAR 5950L LEFT BRACKET MOUNTING SUPPORT FORD BRACKET 2003 06 EXPEDITION 2002 05 EXPLORER 4 DR 2001 04 MUSTANG LINCOLN 2002 05 AVIATOR 2003 06 NAVIGATOR MERCURY 2002 05 MOUNTAINEER 5950 RIGHT MOUNTING BRACKET 5949 KIT PANEL INTRODUCTION PRELIMINARY This premium installation kit is for 2001 06 Select Ford Lincoln Mercury vehicles Included are all the parts you need to mount your car stereo or CD player into your vehicle s dash Refer to the individual instruction in this manual to remove your vehicle s factory radio and assemble the kit CAUTION DISCONNECT YOUR VEHICLE S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE WE RECOMMEND THE USE OF A VOLT OHM METER OVER A TEST LIGHT TO CHECK WIRING A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE S COMPUTER AND OR DIAGNOSTIC SYSTEMS AVOID ALL FACTORY AIRBAG WIRING AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH NOTES e See your vehicle s instructions for any special tools your installation might require e Read all instructions accompanying your car stereo for proper wiring and mounting instructions FACTORY WIRING CODES For Factory Wiring Codes go to Www scosche cars com CAR STEREO CONNECTORS PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO FACTORY WIRING HARNESS FD16
3. nap and lift panel out of the way Extract 2 7mm hex screws from below ashtray Use a panel removal tool to carefully unsnap and remove the entire radio A C control center dash bezel unplug and remove Extract 2 7mm hex screws from below stereo unplug and remove stereo MOUNTING THE STEREO amp Gr on DBL DIN ISO MOUNT 1 Snap the 5950L R brackets to the 5949 kit panel 2 Align position and bolt the DOUBLE DIN head unit to the 5950 brackets Use hardware supplied with stereo to secure the mounting brackets Note If hardware is not supplied with aftermarket stereo use hardware from factory stereo 1525 REAR BRACKET SUPPORT NOTE REAR SUPPORTING THE STEREO ADDS Z DOUBLE DIN TO THE INSTALLATION S STEREO STRUCTURAL INTEGRITY 5950L LEFT MOUNTING BRACKET 5949 KIT PANEL 5950 RIGHT MOUNTING BRACKET
Download Pdf Manuals
Related Search