Metra 99-7875 mounting kit
Contents
1. White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 7 ze EEE NOTES Soon EN Y META 99 7875 99 7875T SS NOTES 99 7875 7875T INSTRUCTIONS A 1 800 221 0932 mu www metraonline com REV 04 21 10 COPYRIGHT 2008 2010 METRA ELECTRONICS CORPORATION INST99 78752. INSTALLATION INSTRUCTIONS FOR PART 99 7875 99 7875T APPLICATIONS Honda Accord 2008 2010 For Non Navigation models with Dual Zone Climate controls Honda Accord Crosstour 2010 99 7875 99 7875T KIT FEATURES J e Painted To Match Factory Dash 99 7875 Charcoal 99 7875T Taupe e DIN Radio Provision with Pocket e ISO Mount Radio Provision with Pocket e Double DIN Radio Provision e Stacked ISO Mount Units Provision e A Radio Housing B ISO Brackets C ISO Trim Plate e D Double DIN Brackets e E Double DIN Trim Plate e F Pocket WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 1729 Honda harness 2008 up e 70 1730 Honda amp interface harness 2008 up Antenna Adapter e 40 HD10 Honda antenna adapter 2005 up TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver e Cutting Tool SAS A 1 800 221 0932 www metraonline com COPYRIGHT 2008 2010 METRA ELECTRONICS CORPORATION LE 99 7875 99 7875T TABLE OF CONTENTS Dash Disassembly Honda Accord 2008 2010 Crosstour 2010 For Non Navigation models with Dual Zone Climate controls 5 7222080008888 A Kit Preparation Kit Assembly DIN Mount Radio Provision with Pocket 4 ISO Mount Radio Provision with Pocket 5 Double DIN Stacked ISO Mount Units Provision 6 PR AONE ica iii AS Note Refer also to the instructions
3. N brackets to the inside edge of the Radio Housing Figure B 3 Slide the Double DIN or stacked ISO mount units into the bracket radio housing assembly and secure the unit s to the assembly using the screws supplied with the unit s Figure C 4 Snap the Double DIN trim plate onto the front of the Housing Radio assem bly Figure C Continue to final assembly Meld 99 7875 99 7875T FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front
4. Phillips screws securing the climate controls to the factory radio assembly and remove the con trols from the assembly Retain the screws and climate controls for re use during kit preparation 12 Remove 4 Phillips screws securing the a c vents to the factory radio assembly and remove the a c vent from the assembly Retain the screws and a c vents for re use dur ing kit preparation 13 Unclip and remove the hazard switch passenger air bag light assembly Retain the hazard switch passenger air bag light assembly for re use during kit prepa ration 14 Remove 4 Phillips screws securing trim panel at the bottom edge of the factory radio assembly and remove the trim panel Retain the screws and trim panel for re use during kit preparation 15 Remove 9 clips from the back of the factory radio assembly Retain the clips for re use during kit prepara tion Continue to kit preparation Y META 99 7875 99 7875T KIT PREPARATION HONDA ACCORD 2008 10 CROSSTOUR 2010 1 Snap the hazard switch passenger air bag light assembly into the radio housing from front Figure A 2 Secure the a c vents into the radio housing using the factory hardware from rear Figure B 3 Secure the climate controls into the radio housing using the factory hard ware from rear Figure C 4 Secure the trim panel onto the radio housing using the factory hardware Figure D 5 Attach the clips to th
5. e back of the radio housing Figure E Continue to kit assembly Om CRETE EN A g eg Z m f Melia 99 7875 99 7875T KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the Radio Housing and secure by bending the o h gt LL u 3 _ B o a 2 5 S D amp 2 T S oO E DIN cage until it snaps into place 2 Slide the aftermarket radio into the Figure B 3 Snap the pocket into the radio housing Figure C Continue to final assembly MEN 99 7875 7875T KIT ASSEMBLY N ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio Mount the ISO Brackets to the radio using the screws supplied with the radio Figure A Slide the radio into the Radio Housing until it snaps into place Figure B Snap the Trim Plate onto the front of the Radio Housing Figure C Snap the Pocket into the Radio Housing Figure C Continue to final assembly ET Y META 99 7875 99 7875T KIT ASSEMBLY eV DOUBLE DIN STACKED ISO MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Cut and remove the center bar from the Radio Housing Figure A 2 Snap the Double DI
6. included with the aftermarket radio KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow ER LEZ 99 7875 99 7875T DASH DISASSEMBLY HONDA ACCORD 2008 10 CROSSTOUR 2010 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Unclip and remove the trim panel from above the glove box at the right side of the factory radio Figure A 3 Unclip and remove the trim panel at the left side of the factory radio Figure B 4 Remove the 2 Phillips screws from the left and right side of the of the factory radio Figure C 5 Unclip and remove the top of the cen ter console including the cup holders Figure D 6 Remove 2 Phillips screws at the bot tom edge of the pocket assembly Figure E 7 Remove 2 Phillips screws facing up inside of the pocket below the factory radio Figure F 8 Unclip and remove the pocket assem bly Figure G Continue on page 2 E 99 7875 99 7875T DASH DISASSEMBLY HONDA ACCORD 2008 10 CROSSTOUR 2010 9 Remove 2 Phillips screws facing up on the bottom of the factory radio Figure H 10 Unclip the factory radio assembly Unplug and remove the radio assem bly Figure I 11 Remove 6
Download Pdf Manuals
Related Search