Metra 99-7869 mounting kit
Contents
1. B Lc ee re OE a HONDA ODYSSEY 2005 2010 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Unclip and remove climate control panel below radio Figure A E Dee 3 Remove 3 Phillips 7 MM screws securing the radio to remove Figure B Menas 99 7869 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET 1 Attach 2 Panel Clips to Radio Housing rear connectors Figure A 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down Figure B 3 Slide the aftermarket radio into the cage and secure Figure C 4 Snap the pocket into the housing Figure D i ey en Zc EEE ee eg ISO MOUNT RADIO PROVISION WITH POCKET 1 Attach 2 Panel Clips to Radio Housing rear connectors Figure A 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit Figure B 3 Slide the head unit into the radio Opening until the side clips engage Figure C 4 Snap the Trim plate into the Radio Housing Figure C 5 Snap the Pocket into the Housing Figure D f Mens 99 7869 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION 1 Attach 2 Panel Clips to Radio Housing rear connectors Figure A 2 Cut and remove the center bar from the 99 7869 radio housing Figure B 3 Snap the Double DIN brackets to the inside edge of the 99 7869 radio housing Figure C 4 Slide the Double DIN2. radio into the bracket trim plate assembly and secure the radio to the assembly using the screws supplied with the radio Figure D 5 Snap the Double DIN trim plate into the radio housing Figure D i P M O EEL ee C STACKED ISO MOUNT UNITS PROVISION 1 Attach 2 Panel Clips to Radio Housing rear connectors Figure A 2 Cut and remove the center bar from the 99 7869 radio housing Figure B 3 Snap the Double DIN brackets to the inside edge of the 99 7869 radio housing Figure C 4 Slide the Stacked ISO units into the bracket trim plate assembly and secure the units to the assembly using the screws supplied with the radio Figure D 5 Snap the Double DIN trim plate into the radio housing Figure D Mena 99 869 KIT ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown Metra recomends using the proper mating adapter and making the connections as shown Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate an
3. INSTALLATION INSTRUCTIONS FOR PART 99 7869 APPLICATIONS Honda Odyssey 2005 2010 99 7669 KIT FEATURES e DIN Radio Provision with Pocket e ISO Mount Radio Provision with Pocket e Double DIN Radio provision e Stacked ISO Mount Units Provision KIT COMPONENTS A Radio Housing B ISO Brackets C Trim Plate D Double DIN Trim Plate E Double DIN Brackets e F Pocket e G Panel Clips 2 Panel Clips supplied user asembly onto rear of Radio Housing required WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 1721 Honda Acura harness 1998 up e 70 1722 Honda harness 2006 up e 40 HD10 Honda antenna adapter 2005 up Phillips Screwdriver Small Flat Blade Screwdriver Socket Wrench PS ONS N G 1 800 221 0932 m www metraonline com COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION war TABLE OF CONTENTS Dash Disassembly Honda Odyssey 2005 2010 vcccccuuuuueccceueenneneeaae 1 Kit Assembly Din Radio Provision with Pocket ccccucucucucuceueueanae 2 ISO Mount Radio Provision with Pocket 0 ccccuccucnueas 3 Double Din Radio Provision uuccccucucusncnccucueanauaes 4 Stacked SO Mount Units Provision ucucauccucusnucuneues 5 Final Assembly ccsavct seas tivetsrss eietieonea eas 6 RNCWE EDGE sar POWER ne Sethi p e Kaa i ee cies mabe phocianigg momo dean bigE F Lagi Gig Hee ra e O ead A R rnr Intact omitir irpo maria betr esr
4. d individually tape off ends of any unused wires to prevent electrical short circuit A Strip wire ends back 1 2 B Twist ends together C Solder D Tape METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black lllumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When Black a wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications G 1 800 221 0932 m www metraonline com REV 04 21 10 COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION INST99 7869
Download Pdf Manuals
Related Search