Metra 99-3306 mounting kit
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 99 3306 APPLICATIONS Chevrolet Aveo sedan 2007 2010 Pontiac G3 2007 2009 99 3306 KIT FEATURES e DIN Mount Radio Provision with Pocket e ISO Mount Radio Provision with Pocket e Double DIN Mount Radio Provision e Stacked ISO Units Provision KIT COMPONENTS A Radio Housing B ISO Brackets C ISO Trim Plate D Double DIN Brackets e E Double DIN Trim Plate F Pocket WIRING AND ANTENNA CONNECTIONS Sold Separately Wiring Harness e 70 2105 GM harness 2006 up e 70 8405 GM Suzuki Daewoo harness 1999 up Antenna Adapter e 40 CR10 CHRYSLER GM antenna adapter 2002 up TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver Socket Set A 1 800 221 0932 m www metraonline com COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION oo 99208 TABLE OF CONTENTS Dash Disassembly Chevrolet Aveo 2007 2010 uucuuucuuucuuanuaags PEER Pontiac G3 2007 2009 ocacccccncnncnncaneannaes TITTY Kit Assembly DIN Mount Radio Provision with Pocket cccsccuuccnusssnnsld SO Mount Radio Provision with Pock t 00cscsccusuuersusnned Double DIN Radio Provision ceuuneuuccuneeuesunsanes4 Stacked ISO Units Provision waccccuucccuccceecneseunesaeneea FINAL ASSOMDN s rerrrrsisinissrrrnid riren Seas deere neers O Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE I2. S POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow PS Oze 99 3306 DASH DISASSEMBLY CHEVROLET AVEO 2007 2010 PONTIAC G3 2007 2009 Di h ive b A E to prevent an accilntal shot OCS G circuit 2 Unclip and remove trim panel around radio Figure A 3 Remove 4 9 32 screws securing the radio Unplug and remove radio Figure B Continue to kit assembly f mens 99 3306 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking outward Figure A 2 Slide the aftermarket radio into the DIN cage until it snaps into place Figure B 3 Snap the pocket into the radio housing Figure C Continue to final assembly x f Mera 99 3306 KIT ASSEMBLY NO ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio Mount the ISO Brackets to the radio using the screws supplied with the radio Figure A Slide the radio into the radio opening until it snaps into place Figure B Snap the ISO Trim Plate onto the front of the Radio Hou
3. cations A 1 800 221 0932 www metraonline com REV 04 21 10 COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION INST99 3306 6
4. ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front 08 Gray Black COUN setae earenaaetoeents Black Left Front White Power Antenna Blue Left Front aaa White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear uan Violet Black Illumination 08 Orange Left Rear uiuia Green Dimmer uaa Orange White Left Rear auaa Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifi
5. sing Figure B Snap the pocket into the radio hous ing Figure C Continue to final assembly RIGHT SIDE CLIP f mes 99 3306 KIT ASSEMBLY DOUBLE DIN MOUNT RADIO PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Cut and remove the center bar from the radio housing Figure A 2 Snap the Double DIN brackets to the inside edge of the radio housing Figure B 3 Slide the Double DIN radio into the bracket radio housing assembly and secure the radio to the assembly using the screws supplied with the radio Figure C 4 Snap the Double DIN trim plate onto the front of the housing radio assem bly Figure C Continue to final assembly 99 3306 KIT ASSEMBLY STACKED ISO UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Cut and remove the center bar from the radio housing Figure A 2 Snap the Double DIN brackets to the inside edge of the radio housing Figure B 3 Slide the stacked ISO units into the bracket radio housing assembly and secure the units to the assembly using the screws supplied with the units Figure C 4 Snap the Double DIN trim plate onto the front of the housing radio assem bly Figure D Continue to final assembly Oe Ra FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist
Download Pdf Manuals
Related Search