Home
Metra 95-7424 mounting kit
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 95 7424 APPLICATIONS Nissan Titan 2008 11 QS4 42e4 KIT FEATURES e Double DIN Radio Provision e Stacked ISO Mount Units Provision e Painted Silver To Match Factory Dash KIT COMPONENTS ey A Double DIN Radio Housing B Double DIN Trim Plate C Double DIN Brackets D Trim Panel o E Two Sided Tape Not Shown Harness amp Antenna Connections sold separatel e 70 7550 Nissan Harness 95 up TOOLS REQUIRED Torx T 10 Driver Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver eS NS A 1 800 221 0932 www metraonline com COPYRIGHT 2010 METRA ELECTRONICS CORPORATION me 95 7424 TABLE OF CONTENTS Dash Disassembly Nissan Titan 2008 11 wa ccu ne 1 Kit Assembly Double DIN Radio Provision ss sssossomunmuus 3 Stacked ISO Mount Units Provision 4 Fig AS SON a en dau nieces NANEN 5 Note Refer also to the instructions included with the aftermarket radio i I Marrs 95 7424 DASH DISASSEMBLY NISSAN Titan 2008 11 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Unclip the entire dash panel including the radio and climate controls Unplug and remove the panel Figure A 3 Remove 4 Phillips screws securing the radio chassis Unplug and remove the chassis Figure B 4 Remove 4 T 10 Torx screws securing the cli
2. mate controls to the dash panel and remove the controls from the panel Retain the screws and climate controls for re use during kit prepara tion Figure C 5 Remove 2 T10 Torx screws securing the passenger air bag status light assembly to the dash panel and remove the light from the panel Retain the screws and light for re use during kit preparation Figure C NOTE The small round Airbag sticker also needs to be removed from the fac tory panel and placed onto the 95 7424 radio housing panel A round piece of double sided tape is provided in case the factory sticker is not strong enough Figure C Continue to kit preparation ie 25 7424 KIT PREPARATON NISSAN Titan 2006 11 A 1 Attach the climate controls to the Trim Panel using the factory hardware removed during the dash disassem bly Figure A 2 Attach the passenger air bag status light assembly to the Trim Panel using the factory hardware removed during the dash disassembly Figure B Also apply to air bag button the small round airbag sticker previously removed in Step 5 dash disassembly Figure B Continue to kit assembly Mers 95 7424 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Snap the Double DIN brackets to the inside edge of the Double DIN radio housing Figure A 2 Slide the Double DIN radio into the Double DIN bracket radio housing as
3. sembly and secure the radio to the assembly using the screws supplied with the radio Figure B 3 Snap the Double DIN trim plate onto the housing radio assembly Figure B Continue to final assembly Mers 95 7424 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Snap the Double DIN brackets to the inside edge of the Double DIN radio housing Figure A 2 Slide the stacked ISO mount units into the Double DIN bracket radio housing assembly and secure the units to the assembly using the screws supplied with the units Figure B 3 Snap the Double DIN trim plate onto the housing radio assembly Figure B Continue to final assembly Ore 5 7424 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble in reverse order of disassembly using the 95 7424 Trim Panel in place of the factory radio trim panel FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head
4. unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 5 95 7424 INSTRUCTIONS ee E 1 800 221 0932 www metraonline com REV 11 18 10 COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST95 7424
Download Pdf Manuals
Related Search
Related Contents
P 622 - Qlima LA FLEUR DE VIE - Nathalie Chiaureli Un travail ré-éducatif ano-rectal de l`enfant de moins de cinq ans Adept MV Controller User`s Guide Doro Congress 150 Tripp Lite DisplayPort to HDMI Converter Video Adapter, 1920x1200/1080p (M/F) Sikadur 301 Copyright © All rights reserved.
Failed to retrieve file