Metra 95-5820 mounting kit
Contents
1. KA I Mais 95 5820 DASH DISASSEMBLY FORD F 150 2009 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the 1 9 32 screw exposed Figure A 3 Remove the rubber pad at the top of the radio trim panel then remove the 2 9 32 screws exposed Figure B 4 Unclip and pull the side panels con taining the a c vents away from the radio trim panel Note It is not nec essary to remove the panels com pletely Figure C 5 Unclip and remove the radio trim panel Figure D Continued on page 2 gt I Mais 95 5820 DASH DISASSEMBLY FORD F 150 2009 6 Unclip and remove the hazard airbag switch assembly from the factory radio trim panel Figure E 7 Unclip and remove the cigarette lighter socket from the radio trim panel Figure F 8 Remove 4 Torx screws securing the factory climate control to the radio trim panel Figure G 9 Remove 4 9 32 screws to remove the factory radio Continue to final preparation FACTORY RADIO TRIM PANEL REAR VIEW K MESA 95 5820 KIT PREPARATION FORD F 150 2009 1 Clip the hazard airbag switch assembly into the radio housing in the same location as the factory radio trim panel Figure A 2 Clip the cigarette lighter socket into the radio housing in the same loca ti2. INSTALLATION INSTRUCTIONS FOR PART 95 5820 APPLICATIONS FORD F 150 an KIT FEATURES e Double DIN Radio Provision e Stacked ISO Mount Units Provision KIT COMPONENTS e A Double DIN Radio Housing B Double DIN Radio Housing Brackets e C Radio Housing Trim Panel D 6 U Style Panel Clips D ANAAANANARAR WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e Please see www metraonline com for specific interface harness _ Antenna Adapter co 40 CR10 Chrysler antenna adapter 02 up TOOLS REQUIRED e Cutting Tool Phillips Screwdriver SocketWrench Torx Driver e Panel Removal Tool G 1 800 221 0932 www metraonline com COPYRIGHT 2009 METRA ELECTRONICS CORPORATION E marr TABLE OF CONTENTS Dash Disassembly FORD F 150 2009 wcccccccncnncncnensnnnnnsnnnnnnnns 12 Kit Preparation FORD F 150 2009 wcuuuncuuunnnuunnnuuunnnuunenunatnase Kit Assembly Double DIN Radio Provision Stacked ISO Mount Units Provision 4 FINAL ASSEMONT pi risirrrririra rir inari rennir ninrin eed Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow
3. on as the factory radio trim panel Figure B 3 Secure the climate control into the radio housing using the factory hardware in the same location as the factory radio trim panel Figure C 4 Attach the 6 U style panel clips to the radio housing in the same location as the factory radio trim panel Figure D Continue to kit assembly KIT REPLACEMENT RADIO TRIM PANEL REAR VIEW KIT REPLACEMENT RADIO TRIM PANEL REAR VIEW a Mel s 95 5820 KIT ASSEMBLY h NO DOUBLE DIN RADIO PROVISION OR STACKED ISO MOUNT UNIT S PROVISION Note Refer also to the instructions included with the aftermarket radio Slide the appropriate side bracket over the mounting legs of the Double DIN trim plate aligning the holes in the trim plate and the bracket and rotate inward Note The notch in the housing should be on top Figure A Slide the Double DIN or stacked ISO mount units into the bracket radio housing assembly and secure the Double DIN or stacked ISO mount units to the assembly using the screws supplied with the Double DIN or stacked ISO mount units Figure B Cut and remove half of the top 2 mounting legs with the brackets attached Figure C Continue to final assembly CUT HERE TOP LEG ONLY SS US UT CUT HERE TOP LEG_ONLY pa QG A 95 5820 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wi
4. ring harness in the dash Metra recommends using the proper mating adapter and making the connections as shown Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly using the 95 5820 radio housing in place of the factory radio trim panel FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short Circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may no
5. t be present on all leads due to manufacturer s specifications 5 95 5620 INSTRUCTIONS G 1 800 221 0932 www metraonline com REV 05 07 09 COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST95 5820
Download Pdf Manuals
Related Search