Miele DA 6290 D Ext
Contents
1. 1 floating bracket to give a choice of position for the exhaust cut out in the ceiling not required for U models 1 hose clip for securing the exhaust ducting to the exhaust stub not required for U models 25 Connection for air extraction Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room The cooker hood should be installed according to local building regulations Seek approval from the building inspector where necessary Only use smooth pipes or flexible hoses made from non flammable materials for the extraction ducting When using an external motor make sure that the exhaust ducting is sufficiently rigid The external motor can cause an underpressure which can result in the exhaust ducting distorting To achieve the greatest possible air extraction with the lowest noise level please note the following To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 150 mm If flat ducting is being used the cross sectional area must not be smaller than the cross sectional area of the exhaust connection All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight as possible 26 Only u2. quw The air is drawn in and cleaned by the grease filters and directed outside The cooker hood is fitted with a non return flap which is closed when the cooker hood is switched off No exchange of room air and outside air can take place When the cooker hood is switched on the non return flap opens for the cooking vapours to be blown directly outside 12 air recirculation U models only qw The air is drawn in and cleaned first by the grease filters and then by a charcoal filter The cleaned air is then recirculated back into the kitchen through grilles in the top of the cooker hood tower Before using the cooker hood in recirculation mode ensure that the charcoal filter is in place See Cleaning and care an external motor EXT models only RR EXT models are designed to be connected to an external motor located outside the room The external motor is connected to the cooker hood by means of a control cable and is operated by the controls on the cooker hood Miele home Con ctivity dai2385 This cooker hood is communication enabled Communication module XKM 2000 DA available as an optional extra enables the operation of the cooker hood to be automatically controlled by the operating status of a Miele electric hob with onset controls For communication to take place the hob must be fitted with the appropriate communication modu
3. Intensive setting For short periods of cooking food with intensive vapours and a strong aroma e g when searing meat you may wish to select level IS the Intensive setting 14 Automatic switch off of the Intensive setting You can set the Intensive setting so that it always only runs for 10 minutes before reverting automatically to level 3 m To set this option both the fan and the hob lighting must be switched off m Press the Run on control 5 415 for approx 10 seconds until the 1 lights up m Then press in turn the Hob lighting control C the symbol and the Hob lighting control amp again If Automatic switch off is not activated 1 and IS will flash m Press the control to activate Auto matic switch off The indicator lamps for fan power levels 1 and IS will now light up constantly Press the control to deactivate the Automatic switch off function m Confirm the selection by pressing the Run on control 5 415 If you do not confirm within 4 minutes the cooker hood will automatically revert to the original setting Operation Run on option 5415 It is advisable to run the fan for a few minutes after cooking has finished to neutralise any lingering odours in the air whether you are using air extraction or recirculation mode The fan can be set to switch off automatically after 5 or 15 minutes m After cooking has finished press the Run on control 5 415 whilst the
4. the data plate correspond with the on site electricity supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt gt The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P For safety reasons this appliance may only be used when it has been fully installed P Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults P Installation maintenance and repairs may only be carried out by a Miele authorised person in strict accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Ensure that current i
5. back into the room when the cooker hood and the heater are in operation simultaneously an underpressure in the room of 0 04 mbar 4 pa is the maximum permissible dai1477 Ventilation can be maintained by air inlets which cannot be blocked in windows doors and outside wall vents One of the following technical measures may be necessary to ensure safe operation f the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently A window contact switch kit is available from good builders merchants Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room when it is or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa switched on The Miele DSM 400 control module offers the possibility of combining other A ventilation brick alone is not generally sufficient to ensure safe ventilati
6. coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60335 28 Operation with Control module DSM 400 The Miele DSM 400 control module can be used to combine the cooker hood with other components It enables the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch not supplied to the appliance Once connnected the cooker hood can only be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The indicator lamp for the On Off touch control on the cooker hood will flash The cooker hood lighting is not affected by this EXT models can also be connected to a window conta
7. edge feature lighting You can change the colour of the glass edge lighting to any colour you like The lighting is pre set to be white m Switch on the glass edge feature lighting m By repeatealy pressing the Colour change control you can scroll through the six pre set standard colour settings as follows CD White 2 Green Red Blue 8 Rapid colour change The colour of the lighting changes continuously The colours rotate once every minute Initially the Colour change symbol flashes rapidly Slow colour change As with but the colours rotate once every 15 minutes Initially the Colour change symbol flashes slowly 16 You have the option of saving one favourite colour to memory To select the colour m Select the rapid or slow colour change colour setting oder The colours start to rotate m When the colour required appears press and hold the Colour change control until the glass edge feature lighting flashes three times This colour is then saved in an additional colour setting m t can be selected at any time until you decide to save a different colour in the same way m To switch it off press the glass edge feature lighting button The lighting will switch off after a slight hesitation When the glass edge lighting is next switched on the most recently selected colour setting CD to 2 will come on again Safety switch off Should the cooker hoo
8. fan is still running Press once The fan will switch off after 5 minutes 5 amp lights up Press twice The fan will switch off after 15 minutes 415 lights up If you press the Run on control 5 415 again the fan remains on 5 415 goes out To switch the fan off D m Press the On Off control D to switch the fan off The D symbol goes out Hob lighting To switch the hob lighting on The hob lighting can be switched on and off independently of the fan m Press the Hob lighting control briefly The symbol lights up The hob lighting will switch on at maximum brightness To dim the hob lighting The brightness of the hob lighting can be adjusted m With the hob lighting switched on press and hold the Hob lighting control XX The brightness will gradually dim until you release the control m lo increase the brightness press and hold in the Hob lighting control X again to the level required then release it If you keep your finger on the Hob lighting control X the lighting will continue to change between bright and dim To switch the hob lighting off m Touch the Hob lighting control briefly The 9 symbol goes out Operation Glass edge feature lighting m Press the control for the glass edge feature lighting to switch it on This can be switched on and off independently from the fan or the hob lighting To change the colour of the glass
9. h IS Intensive setting 700 m h Recirculation power for DA 6290 D U with charcoal filter WS nenne 150 m h Level Z cssc rr Res 260 m h Level3 0 sess 400 m h IS Intensive setting 500 m h Optional accessory for recirculation mode Miele charcoal filter DKF 12 1 For EXT models the connected load and extraction power will depend on the type of external motor fitted Length of connection cable to external MOLO s oet snis Boe ante 1 4m 32 33 34 35 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E
10. lamps will go out If you do not confirm within 4 minutes the cooker hood will automatically revert to the original setting 18 Reading the filter operating hours counter To check the percentage of time set already used m Press the On Off control to switch the fan on m Press and hold the Operating hours counter control Once to read the Grease filter operating hours The Grease filter symbol amp lights up Twice to read the Charcoal filter operating hours The Charcoal filter symbol lights up One or more of the power level indicators will flash The number of power level indicators flashing shows the percentage of the operating time which has already been used up 1 25 1and2 50 1to3 75 1tolS 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Cleaning and care A range of Miele branded cleaning and conditioning products is available to order from Miele see back page for details or via the internet at www miele shop com Before any cleaning or maintenance work is carried out disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or itis switched off at the wall socket and the plug is withdrawn or the fuse from the fused spur connection unit is withdrawn or the mains fuse is disconnected or the screw out fuse i
11. Miele Operating and installation instructions Cooker hood DA 6290 D DA 6290 D U DA 6290 D EXT To avoid the risk of accidents en GB SG or damage to this appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 740 590 Contents Caring for the environment 0 0 000000 cee ee 3 Warning and safety instructions 0 0 0 0 eee 4 Guide to the machine 0 0 0 00 ls i liess 10 Modes of operation liiiisisiiie eiie 12 Miele home i e ades 1 ka raa a Rex d eus de cs 13 GON ENVIY area een E 13 Operation bre n Reese Disks 14 To switch the fan on D 1 eee eee 14 To select a power level Fee caed aru ai eg a ilis lesse 14 INTENSIVE seting a5 4 d eco ape Dao efe cz de t RE a hee 14 R ri ori option b a5 neck e reed eek 15 slojeuilo nilao po EE 15 Glass edge feature lighting 7 0 e 16 To change the colour of the glass edge feature lighting Yr 0 16 Operating hours counters 8 eee eee 17 Cleaning and care 0 00 0 teas 19 IHOUSIFIQi a Ta ed ee y eed reae eed bor Dea der aq are PETRO obe 19 Grease Tels x sex dose wok cd dog ale ed cea heals Pate RR Bodo and e ed rapa BEES Ss 20 Resetting the Grease filter operating hours counter 0005 21 Charcoal TIGE setas choc Dae nul bc TU e CR an keller 22 Resetting the Charcoal filter operating hours c
12. amp as grease particles from your fingers will adhere to the surface and damage it Please follow the manufacturer s instructions dai2328 dai2329 m o access the halogen lamp push the lamp cover gently upwards The cover will open and can be pulled down m Pull the old halogen lamp out of the connection socket and replace it with a new one 20 W G 4 cap m Push the cover back up and make sure it clicks into place 23 Appliance dimensions 1 Cut out for feeding through the exhaust ducting the mains cable and with EXT models the connection cable to the external motor In recirculation mode only the mains cable is required Exhaust connection 150 mm not needed for recirculation mode The exhaust connection in the ceiling plate is not fixed in the middle which means that the hood can also be installed where the exhaust cut out in the ceiling is not centrally positioned over the hob There is a max margin of 30 mm in any direction 24 Safety distance between hob and cooker hood When planning the installation height of your cooker hood the minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows unless a greater distance is specified by the manufacturer of your cooking appliance 550 mm above electric hobs and cookers 650 mm above an open grill or deep fat fryer 650 mm above gas hobs and c
13. and m Clean the filters with a soft nylon brush in a mild solution of hot water and a little washing up liquid Do not use neat washing up liquid Do not use cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaners oven sprays Cleaning the grease filters in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright and wash using a 65 C programme ensuring the spray arm is not obstructed m f a Miele dishwasher is being used select the Sensor wash programme m Use a mild dishwasher detergent Depending on the cleaning agent used cleaning the filters in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filters in any way m After cleaning leave the filters to dry on an absorbent surface before replacing them m When removing the filters for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire m Replace the grease filters making sure that the locking clips are facing down towards the hob dait619 m f a grease filter is inadvertently replaced upside down insert a small screwdriver blade into the slit to disengage the clip Resetting the Grease filter operating hours counter After cleaning the operating hours counter ne
14. ches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes MSE m amp 3 P Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode with or without an external motor fitted the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion e U dai1474 Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn
15. ct switch Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connection This enables a further appliance to be controlled by the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional diameter If a sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be switched off when the cooker hood is in operation See also Warning and Safety instructions 29 Operation with Control module DSM 400 Connection to a light switch The control module can be used to switch on the cooker hood lighting and also to dim it via a light switch in the house The glass edge feature lighting cannot be switched on and off in t
16. d be left on the fan will switch off automatically after 10 hours The lighting will remain on Pressing the On Off control D will switch the fan back on again Operation Operating hours counters The number of hours the appliance has been in operation is stored in memory When the Grease filter symbol lights up the Operating hours counter is signalling that the grease filters need to be cleaned On U models the Charcoal filter symbol will also light up when the charcoal filter needs to be replaced Further information about cleaning and changing the filters and resetting the Operating hours counter can be found under Cleaning and care Altering the Grease filter operating hours counter You can set the operating hours counter for the grease filter to suit the type of cooking you do Select a short time if you roast or fry a lot If you use very little fat for cooking select a longer time If you only cook occasionally we recommend that you still select a short time because grease which has built up gradually over a long period of time will harden on the filter and make cleaning more difficult The grease filter operating hours counter is set at the factory for 30 hours This can be lengthened or shortened You can choose 20 30 40 or 50 hours m Press the On Off control to switch the fan off m Press the Run on control 5 2 15 and the Operating hours counter B a
17. d to collect and evaporate any condensate which may occur Condensate traps are available for 125 mm or 150 mm ducting When installing a condensate trap ensure that it is positioned vertically and if possible directly above the exhaust connection The arrow on the housing indicates the direction of air flow 27 Electrical connection NAI electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the Uk Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The connection data is given on the data plate See After Sales Service Ensure that this data matches the household mains supply If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are
18. eds to be reset m Whilst the fan is switched on press the Operating hours control for approx 3 seconds until only the 1 is flashing The Grease filter symbol B goes out If you want to clean the grease filters before the operating hours counter has reached its maximum Press the Operating hours control for approx 6 seconds until only the 1 is flashing 21 Cleaning and care Charcoal filter U models only If the cooker hood is connected for recirculation a charcoal filter must be inserted in addition to the grease filters This is designed to absorb cooking odours It is fitted in the canopy above the grease filters New charcoal filters can be purchased from your Miele dealer from the Miele Spare Parts Department or via the internet at www miele shop com See back cover for contact details and Technical data for the model number of the filter m Before fitting or replacing a charcoal filter the grease filters must first be taken out see previous section for instructions on how to do this m ake the charcoal filter out of its packaging m insert the charcoal filter into the canopy m Replace the grease filters 22 When fitting for the first time m Set the operating hours counter to suit your requirements see Operation Always replace the charcoal filter im mediately if the Charcoal filter symbol lights up or itis no
19. for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Warning and safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the safety installation use and maintenance of the appliance Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application P This appliance is not designed for commercial use It is intended for use in domestic households and for use in similar working and residential environments such as Shops Offices and showrooms and by residents in establishments such as Hostels and guesthouses P It must only be used as a domestic appliance to extract vapours and remove odours from cooking Any other usage is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect o
20. his way Installation The control module is fitted in the tower after the cover plate has been unscrewed from the ceiling The control module is supplied with its own detailed operating and installation instructions 30 After Sales Service In the event of a fault which you cannot correct yourself or if the appliance is under guarantee please contact Your Miele Dealer Chartered Agent or The Miele Service Department see back cover for address When contacting your Dealer or Miele please quote the model and serial number of your appliance These are shown on the data plate which is visible when the grease filter is removed For G B Please note that telephone calls may be monitored and recorded for training purposes N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions 31 Technical data Total connected load 300 W Fan motor 2 20204 200 W Hob lighting 4x 20W Glass edge feature lighting 2 x 10 W VON AG Ss cus t eot e ee ee AC 230 V Freguerney xs exe ren 50 Hz FUSTAN xau io es 5A Weight DA 6290 D xax ab S 33 kg DA 6290DU 34 kg DA 6290 DEXT 31 kg Fan performance according to EN 61591 Extraction power for DA 6290 D with 150 mm ducting Levell ise 200 m h Level D css sd renes 320 m h EL eva 480 m
21. ion may collect in the hood which could cause corrosion P When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire P Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation P The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care P The cooker hood can get very hot during cooking due to heat rising from the hob Do not touch the housing or the grease filters until the cooker hood has cooled down P Do not use a steam cleaner to clean this appliance Steam could reach the electrical components and cause a short circuit Warning and safety instructions Correct installation P Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob gt The minimum safety distances between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions section of this booklet must be maintained unless the hob manufacturer states that a greater safety distance is required If more than one cooking appliance is fitted beneath the cooker hood and they have different mini
22. le 2 The hob transmits information about its operating status to the cooker hood via the household power supply Powerline When the hob is switched on the cooker hood lights and the fan also comes on During cooking the cooker hood automatically sets its power level according to the number of cooking zones in operation and their power levels After switching the hob off the fan and the hob lighting will switch off automatically after a period of time For detailed information about this function please read the separate instruction booklet supplied with the XKM 2000 DA communication module The communication module is fitted to the cooker hood in the area of the motor and is connected to the controls of the cooker hood This module must be installed by a Miele service technician or suitably qualified electrician Operation To switch the fan on D m Press the On Off control D The fan will come on at power level 2 The symbol and the 2 light up If the cooker hood has been connected to a window contact switch via the Miele DSM 400 control moduleDSM 400 then the fan cannot be switched on if the window is shut The D symbol flashes To select a power level 4 m To select a lower power level press the symbol or to select a higher power level press the symbol Depending on the intensity of the cooking vapours levels 1 to 3 are usually sufficient for normal cooking
23. longer effective in absorbing kitchen odours It should however be replaced at least every 6 months Used charcoal filters can be disposed of with the normal household waste Resetting the Charcoal filter operating hours counter After changing the charcoal filter the Operating hours counter needs to be reset m To do this with the fan switched on press the operating hours control once Then press it again and hold for approx 3 seconds until only the 1 is flashing The Charcoal filter symbol will go out If you want to change the charcoal filter before the operating hours counter has reached its maximum Press the operating hours control once Then press it again and hold for approx 6 seconds until only the 1 is flashing Cleaning and care Changing a halogen lamp m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that it is switched off at the isolator or it is switched off at the wall socket and the plug is withdrawn or the fuse from the fused spur connection unit is withdrawn or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off Let them cool down before you change them Do not touch the surface directly when changing a l
24. mail customercare miele in Internet www miele in Germany Miele amp Cie KG Carl Miele StraBe 29 33332 Gutersloh Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 2810 ce M Nr 07 740 590 03
25. mum safety distances to the cooker hood select the greater distance P Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves P All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants gt The appliance must not be connected to a chimney or vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice Accessories P Only use genuine Miele original spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Guide to the machine 1 10 T 12ss sAss e e v a 2 D Guide to the machine Cover plate 2 Tower Canopy 4 Recirculation grille U models only 8 Controls Glass edge feature lighting Hob lighting Cha
26. on NThe overall ventilation condition of the dwelling must be taken into account If in any doubt the advice of a competent builder or for gas a qualified gas fitter registered with an official gas safety body in accordance with national safety regulations GasSafe in the UK must be sought components with the cooker hood see Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a competent builder or for gas a qualified gas fitter GasSafe registered in the UK must be sought If the hood is being operated in recirculation mode the above restrictions do not apply Warning and safety instructions Correct use P Never use an open flame beneath the cooker hood To avoid the danger of fire do not flamb or grill over an open flame When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard P When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat P Always switch the cooker hood on when a cooking zone is in use otherwise condensat
27. ookers If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance a minimum safety distance of 760 mm must be maintained between the burner and the lower edge of the cooker hood See Warning and Safety instructions for further information When deciding on the safety distance between the hob and cooker hood please note that a distance of 650 mm above electric cookers hobs may be preferable to give more working space under the hood Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safety instructions at the beginning of this booklet This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on oxygen from the same room to avoid the danger of toxic fumes building up Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Assembly parts mm gt 0 0 ID 4 screws 8 x 60 mm with 4 washers and 4 plugs S 10 to secure the cover plate to the ceiling The screws and plugs are for use in concrete ceilings only For other types of construction alternative suitable fixings will be required Make sure the ceiling is strong enough to bear the weight of the cooker hood 2 screws M4 x 8mm for securing the tower c 4 spacers to use in the event of an uneven ceiling
28. ounter 005 22 Changing a halogen lamp 0 000 cece catia iien eh 23 Appliance dimensions 0 0002 liess 24 Installation o oce oe Ro aoa RR Oe SRL DOR des s 25 Installation instructions x wisi sat haere eg vie xa etx Space E A UO Rd Edd 25 ASSEMDIY DIE ceto pe ua etat ber cett daret BAe Sl a et iur ehe 25 Connection for air extraction llli ll liess 26 Condensate taD usi 20 44 ong ok Rege e ERE a ee eee Je epe dues 27 lu CP ea E Are Armani E ee 27 Electrical connection 00 002 28 Operation with Control module DSM 400 0 0004 29 Connection to a window contact switch iiis 29 Potential free connection liie 29 Connection to a light switch liiis 30 After Sales Service lilii ili eae 31 Technical data 0 0000 lees 32 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential
29. out causing minor marks to the surface material This can become particularly noticeable with darker colours and if there is halogen lighting in the kitchen Cleaning and care Important for the controls The controls may suffer discolouration or damage if soiling is left on them for too long Remove soiling straight away Observe the General notes on cleaning earlier in this section Do not use stainless steel cleaning agents on the controls Important for the glass edging m The glass edging can be cleaned using a proprietary non abrasive cleaning agent designed specifically for use on glass Do not use sharp metal tools oven sprays 20 Grease filters The re usable metal grease filters in the appliance remove solid particles grease dust etc from the kitchen vapours preventing soiling of the cooker hood The grease filters should be cleaned regularly at least every 3 4 weeks to avoid a built up of grease but always clean immediately if the Grease filter operating hours control lights up An oversaturated filter is a fire hazard dai2544 m To take out the grease filters release the locking clip on the filters lower the filters 45 unhook them at the back and remove them To avoid damaging the filters or the hob below make sure you hold the filters securely at all times when handling them Cleaning and care Cleaning the grease filters by h
30. r improper use or operation of the appliance P This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety Safety with children P This appliance is only intended for use by adults who have read these instructions It is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen P Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse P Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Warning and safety instructions Technical safety P Before installation check the cooker hood for visible signs of damage Under no circumstances should you install or use a damaged appliance It could be dangerous P Before connecting the appliance to the mains supply make sure that the voltage and frequency details given on
31. rcoal filter Special accessory for recirculation mode U models only Grease filters On Off touch control for glass edge feature lighting Touch control for the hob lighting This control can be used to switch the hob lighting on and off and is also a dimmer switch 42 On Off touch control for the fan 4 Touch controls to select the fan power level Touch control for the run on function This control activates the run on option The fan can be set to switch off automatically after either 5 or 15 minutes amp 9 Operating hours control The grease filter symbol amp for the operating hours control lights up when the grease filters need to be cleaned The charcoal filter symbol lights up when the charcoal filter used in recirculation mode needs to be replaced For this to happen the operating hours counter needs to be activated before the appliance is used for the first time U models only The control is used to reset the appropriate operating hours counter each time the grease filter is cleaned or the charcoal filter has been changed see Cleaning and care It can also be used to check and alter the operating hours counter Colour change touch control This control is used to change the colour ofthe glass edge lighting For information about using the appliance see Operation Modes of operation The cooker hood works with air extraction excluding U models
32. s not supplied to the appliance until after maintenance or repair work has been carried out P Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or itis switched off at the wall socket and the plug withdrawn or the fuse from the fused spur connection until is withdrawn Warning and safety instructions P Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P For appliances with an external fan motor fitted EXT models the connection of the two units must be made using the connection cable and the plug connectors These models may only be combined with a Miele external motor P This appliance may only be used in mobile installations if a risk assessment of the installation has been carried out by a suitably qualified engineer P In areas which may be subject to infestation by cockroa
33. s removed in countries where this is applicable Housing General The surfaces and controls are susceptible to scratches and abrasions Please observe the following cleaning instructions m All external surfaces and controls can be cleaned using a Miele E Cloth or with warm water and a little washing up liquid applied with a well wrung out soft sponge or cloth Do not use too much water when cleaning the controls Water could penetrate into the electronics and cause damage m Wipe the surfaces dry using a soft cloth Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents These will damage the surface material Important for appliances with stainless steel housing This information does not apply to the controls Stainless steel surfaces can be cleaned using the Miele E Cloth or with a suitable non abrasive proprietary cleaning agent for stainless steel following the manufacturer s instructions on the packaging To help prevent re soiling a proprietary conditioning agent for stainless steel can also be used Follow the manufacturer s instructions on the packaging Important for appliances with lacquered housing Special order finish It is very difficult to clean this type of surface with
34. se wide radius bends The exhaust ducting should not be kinked or compressed Ensure that all connections are strong and airtight Where ducting is horizontal it must be laid to slope away at at least 1 cm per metre This is to ensure that condensate cannot drain back into the cooker hood If the exhaust air is to be ducted into the open air the installation of a telescopic wall vent or roof vent is recommended dai2538 If the exhaust air is to be ducted into a vent flue the ducting must be directed in the flow direction of the flue Connection for air extraction Important Cooker hoods designed for use with an external motor EXT models have an If the exhaust ducting is to run through integrated condensate trap rooms ceiling space etc where there may be great variations in temperature between the different areas the Silencer problem of condensation will need to optional accessory for EXT be addressed The exhaust ducting will need to be suitably insulated Condensate trap optional accessory dai2003 To achieve even further reductions in noise levels a special silencer can be fitted in the ducting system It can be sited at any suitable position in the ducting system between the cooker hood and the external motor dai1585 In addition to insulating the exhaust ducting we recommend that a suitable condensate trap is also installe
35. t the same time The Grease filter symbol and one of the fan levels flash Power level indicators 1 to IS show the time set 1 20 hours 2 30 hours 3 40 hours IS 50 hours m Press the symbol to select a shorter operating time or the symbol to select a longer operating time m Confirm the selection by pressing the operating hours control All the lamps will go out If you do not confirm within 4 minutes the cooker hood will automatically revert to the original setting Operation Activating and altering the Charcoal filter operating hours counter U models only The charcoal filter is needed for recirculation mode On delivery the Operating hours counter for the charcoal filter is deactivated Before using the cooker hood for the first time after inserting the charcoal filter set the charcoal filter operating hours counter to suit the type of cooking you do as follows m Press the On Off control to switch the fan off m Press the symbol and the Operating hours control at the same time The Charcoal filter symbol and one of the fan levels flash Power level indicators 1 to IS show the time set 1 120 hours 2 180 hours 3 240 hours IS Deactivated m Press the symbol to select a shorter operating time or the symbol to select a longer operating time m Confirm the selection by pressing the operating hours control All the indicator
Download Pdf Manuals
Related Search