Miele DA 5000 D
Contents
1. Ventilation can be maintained by air inlets which must not be blocked in windows doors and outside wall vents or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa A ventilation brick alone is not generally sufficient to ensure safe ventilation AM The overall ventilation condition of the dwelling must be taken into account If in doubt the advice of a competent builder or for gas a qualified gas fitter Corgi registered in the UK must be sought One of the following technical measures may be necessary to ensure safe operation If the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently A window contact switch kit is available from good builders merchants Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room when it is switched on The Miele DSM 400 control module offers the possibility of combining other components with the cooker hood see2. Changing a fluorescent tube m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that it is switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the fuse from the fused spur connection unit is withdrawn or it is switched off at the mains fuse box To avoid damaging the glass cover or the hob below make sure you hold the glass cover securely at all times when handling it m Push the glass cover back slightly then angle it down at the front to remove Use a lever to help you if required dai2211 m Twist the fluorescent tube approx 180 and remove it m Replace it with a new fluorescent tube of the same specification 14 W colour 830 m To fit it follow the instructions for removal in reverse 21 Appliance dimensions 1 Cut out for feeding through the exhaust ducting and the mains cable Floating bracket 200 mm The floating bracket means that the hood can also be installed where the exhaust cut out in the ceiling is not centrally positioned over the hob There is amax margin of 40 mm in any direction 22 Safety distance between hob and cooker hood The minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows unless a greater distance is specified b
3. Fan performance according to EN 61591 Extraction power with extraction system 200 mm Level as ok dncon casks reines 350 m h Levelll 600 m h Level Ill 850 m3 h Level IV Intensive Setting 1 300 m h Unrestricted 1 450 m3 h 30 31 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk Internet www miele hk India Miele Appliances India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele
4. The re usable metal grease filters in the appliance remove solid particles grease dust etc from the kitchen vapours preventing soiling of the cooker hood The grease filters should be cleaned regularly at least every 3 4 weeks to avoid a build up of fat but always clean immediately if the 8 sensor lights up An oversaturated filter is a fire hazard To remove the grease filters the canopy needs to be open m Touch the O sensor to switch the fan on The fan will start running at power level 2 and the canopy will open m Touch the 2 sensor for approx 5 seconds until the fan switches off The canopy will remain open 18 To avoid damaging the filters or the hob below make sure you hold the filters securely at all times when handling them dai2197 m Holding the grease filter by the handle push upwards out of the lower groove hinge it forwards and lift it down and out Cleaning the grease filters by hand m Clean the filters with a soft nylon brush in a mild solution of hot water and a little washing up liquid Do not use neat washing up liquid Do not use cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaning agents oven sprays Cleaning and care Cleaning the grease filters in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright
5. Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a qualified builder gas fitter Corgi registered in the UK or electrician must be sought Warning and Safety instructions Correct use gt Never use an open flame beneath the cooker hood To avoid the danger of fire do not flamb or grill over an open flame under the cooker hood When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard B gt When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat PD Always switch the cooker hood on when a cooking zone is in use otherwise condensation may collect in the hood which could cause corrosion gt When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire P Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the ap
6. and wash on a 65 C programme ensuring the spray arm is not obstructed If a Miele dishwasher is being used select the Sensor wash programme m Use a mild dishwasher detergent Depending on the cleaning agent used cleaning the filters in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filters in any way m After cleaning leave the filters to dry on an absorbent surface before replacing them m When removing the filters for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire dai2206 m When the cooker hood is operating grease residues are deposited in the grooves on either side of the canopy Clean these grooves and the grease filter holders every time the grease filters are removed m Replace the grease filters m Then touch any of the 1 to 4 sensors The fan will then switch back on Resetting the grease filter operating hours counter After cleaning the operating hours counter needs to be reset m Touch the sensor to switch the fan on m Touch the 8 sensor for approx 3 seconds until only the 1 sensor is flashing The 8 sensor light will go out If the grease filters are cleaned before the operating hours counter has reached its maximum m touch the 8 sensor for approx 6 seconds until only the 1 sensor is flashing Cleanin
7. fan off CD m Touch the O sensor to switch the fan off The canopy will close m f the canopy needs to be kept open after it has been switched off e g for cleaning touch the current fan level sensor for approx 5 seconds whilst the fan is running until the fan switches off The canopy will remain open To switch the fan on again touch any of the fan level sensors 14 Hob lighting amp The hob lighting can be switched on and off independently of the fan To switch the hob lighting on m Touch the sensor briefly The lighting will switch on at maximum brightness To dim the hob lighting The brightness of the lighting can be adjusted m With the lighting switched on touch and hold the sensor The brightness will gradually dim until you release the sensor m To increase the brightness touch the sensor again to the level required then release it If you keep your finger on the sensor the light will continually change between bright and dim To switch the hob lighting off m Touch the sensor briefly Operation Feature lighting The feature lighting can be switched on and off by touching the 2 sensor Safety cut out Should the cooker hood be left on the fan will switch off automatically after 10 hours The lighting will remain on m Touching the sensor will switch the fan back on again Operating hours counter 8 The number of hours the appliance has be
8. ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa iele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 4209 CE M Nr 07 087 760 06
9. not supplied to the appliance Once connnected the cooker hood can only be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The O sensor on the cooker hood will flash The cooker hood lighting is not affected by this Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connection This enables a further appliance to be controlled by the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional diameter Ifa sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be switched off when the cooker hood is in
10. work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work PD Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used gt During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or it is switched off at the wall socket and the plug withdrawn or the fuse from the fused spur connection unit is withdrawn Warning and Safety instructions gt Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating gt gt This appliance may only be used in mobile installations such as ships caravans aircraft etc if a risk assessment of the installation has been carried out by a suitably qualified engineer gt gt In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by coc
11. Miele Operating and installation instructions Cooker hood DA 5000 D To avoid the risk of accidents en GB IRL ZA or damage to this appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 087 760 Contents Caringfortheenvironment 3 Warning and Safety instructions 4 Guide to the appliance 10 Mode of operation 12 Operation AA cw denn Meh eda ele whan adel we beh do aeedee ac 13 To switch the fan On IA IIIA WI EEPE 13 To select a power level 13 Run On Option 52615 s24 lt ceaae ewe entaa ae cake w RSA oa x 14 Toswitch the fan off AA t 42 506682 a0 eee cr desde Rd owbeo cates as 14 Hoblighting ened peo ba eck do YSN AG LS Ses Od dak wee EA 14 Feature lIGHUAG c03vveds dente teee ee hage Perea dad ap tad bo pads baa wie 15 SAE CUOU IA mae ate nation ae wis tae hed ede denon ee nelle te 15 Operating hours counter B 15 Sensor control audibletones 16 Cleaning and care 17 HOUSING 40 4 natn race aa a AE OS eR Re ee ea 17 Grease filters 18 Resetting
12. data matches the household mains supply If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60335 26 Operation with Control module DSM 400 The Miele DSM 400 control module can be used to combine the cooker hood with other components It enables the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch
13. en in operation is stored in memory The operating hours counter tells you when the grease filters need to be cleaned After 30 hours of operation or another time if the operating hours counter has been altered the 8 sensor will light up The grease filters must then be cleaned Afterwards the operating hours counter will need to be reset see Cleaning and care Reading the grease filter operating hours counter To check the percentage of time set already used m Touch the sensor to switch the fan on m Touch and hold the 8 sensor One or more of the 1 to 4 sensors will flash The number of flashing sensors indicates the percentage of the operating time which has already been used up Sensor 1 25 Sensors 1 and 2 50 Sensors 1 to 3 75 Sensors 1 to 4 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Operation Altering the grease filter operating hours counter You can set the operating hours counter to suit the type of cooking you do The operating hours counter is set at the factory for 30 hours Select a shorter time of 20 hours if you fry a lot If you only cook occasionally we still recommend 20 hours because grease which has built up gradually over a long period of time will harden on the grease filters and make cleaning more difficult If you use very little fat for co
14. for other purposes seek professional advice Accessories gt Only use genuine Miele spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Guide to the appliance AA os a m 1 2 3 4 Guide to the appliance Cover plate 2 Tower Canopy The canopy opens as soon as the fan is switched on Feature lighting Controls The symbols act as touch controls To select a function touch the relevant symbol An audible tone sounds briefly to confirm selection Hob lighting Grease filters 9 Touch control for the feature lighting Touch control for hob lighting This control switches the lighting on and off and is also a dimmer switch 49 Touch control for switching the fan on and off Touch controls to select the fan power level 42 Touch control for the run on option The fan can be set to switch off automatically after either 5 or 15 minutes 49 Touch control for the grease filters The touch control lights up when the grease filters need to be cleaned The touch control is used to reset the operating hours counter every time the grease filters are cleaned see Cleaning and care It ca
15. g and care Changing a halogen lamp To change the lamps the canopy needs to be open m Touch the O sensor The fan will start running at power level 2 and the canopy will open m Touch the 2 sensor for approx 5 seconds until the fan switches off The canopy will remain open m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that it is switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the fuse from the fused spur connection unit is withdrawn or it is switched off at the mains fuse box m Remove the grease filters Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off danger of burning Wait until the lamps have cooled down before changing them 20 dai2207 m Press the lighting unit down slightly through the hole above the lamp as shown m Turn the halogen lamp anti clockwise out of its socket m Replace it with a new halogen lamp specification GU GZ 10 230 V 50 W Screw the lamp into the socket and push it upwards We recommend only using lamps of the same specification and also made by the same manufacturer as the ones being replaced m Replace the grease filters m Reconnect the cooker hood to the mains supply The canopy will close Cleaning and care
16. he appliance to the mains supply make sure that the voltage and frequency details given on the data plate correspond with the on site electricity supply see After Sales Service If they do not correspond the appliance could suffer damage Consult a qualified electrician if in any doubt gt The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P gt For safety reasons this appliance may only be used when it has been fully installed B Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults gt Installation maintenance and repairs may only be carried out by a Miele authorised person in accordance with current national and local safety regulations Repairs and other
17. kroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes ai j7 J PIS I JSS gt Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion dai1474 Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and Safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously an underpressure of 0 04 mbar 4 pa is the maximum permissible in the room dai1477
18. l packaging materials safely as soon as possible Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person Warning and Safety instructions This appliance complies with all relevant local and national safety reguirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the safety installation use and maintenance of the appliance Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application P gt This appliance is intended for domestic use only Any other usage is at the owner s risk and could be dangerous The manufacturer can
19. leaning instructions m All external surfaces and controls can be cleaned using an E cloth available from the Miele Spare Parts Department or via the Internet on www miele shop com depending on country or with warm water and a little washing up liquid applied with a well wrung out soft sponge or cloth Only use a damp cloth as water could get into the appliance and cause damage m Wipe the surfaces dry using a soft cloth Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents These will damage the surface material Important for appliances with stainless steel surfaces m Stainless steel surfaces can be cleaned using the Miele E Cloth or with a suitable non abrasive proprietary cleaning agent following the manufacturer s instructions on the packaging m To help prevent re soiling a proprietary conditioning agent for stainless steel available from the Miele Spare Parts Department or via the internet on www miele shop com can also be used Important for appliances with glass surfaces m Glass surfaces can be cleaned using a proprietary non abrasive cleaning agent designed specifically for use on glass Do not use sharp metal tools oven sprays Cleaning and care Grease filters
20. lue the ducting must be directed in the flow direction of the flue Important If the exhaust ducting is to run through rooms ceiling space etc where there may be great variations in temperature between the different areas the problem of condensation will need to be addressed The exhaust ducting will need to be suitably insulated Connection for air extraction For exhaust ducting with a diameter of 200 mm the following accessories are required S lt L Exhaust grille DFG 200 for mounting on the external wall Flashing Roof ducting DDF 200 for mounting on a sloping tiled roof Exhaust hose DAS 200 Reducing collar for the exhaust stub if using exhaust ducting with a 150 mm diameter 25 Electrical connection JAI electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the Uk Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The connection data is given on the data plate See After Sales Service Ensure that this
21. n also be used to check and alter the operating hours counter For information about using the appliance see Operation Mode of operation The cooker hood works with air extraction The air is drawn in and cleaned by the grease filters and directed outside The cooker hood is fitted with a non return flap which is closed when the cooker hood is switched off No exchange of room and outside air can take place When the cooker hood is switched on the non return flap opens for the cooking vapours to be blown directly outside 12 Operation To switch the fan on m Touch the sensor dai2205 The fan runs at power level 2 The and 2 sensors light up The canopy will open If the cooker hood has been connected to a window contact switch via the Miele DSM 400 control module then the fan cannot be switched on if the window is shut The sensor will flash To select a power level Depending on the intensity of the cooking vapours levels 1 to 3 are usually sufficient for normal cooking m Select the level you require by touching the 1 2 or 3 sensors Intensive setting m For short periods of cooking food with intensive vapours and a strong aroma e g when searing meat you may wish to select level 4 the Intensive Setting Automatic switch off of the Intensive setting You can set the Intensive setting so that it always only runs for 10 minute
22. not be held liable for damage resulting from incorrect or improper use or operation gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been given instruction concerning its use by a person responsible for their safety Safety with children gt gt This appliance is only intended for use by adults who have read these instructions gt gt This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen B Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse PD Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Technical safety gt Before installation check the cooker hood for visible signs of damage Under no circumstances should you use a damaged appliance A damaged appliance is dangerous Warning and Safety instructions gt gt Before connecting t
23. oking select a longer time To alter the operating time m Touch the sensor to switch the fan off m Touch the 52415 and 8 sensors at the same time The 8 and one of the 1 to 4 sensors will flash The 1 to 4 sensors indicate the time which has been set Sensor 1 20 hours Sensor 2 30 hours Sensor 3 40 hours Sensor 4 50 hours 16 m Touch the 1 sensor to select a shorter time and the 4 sensor to select a longer time until the time required has been set m Confirm your selection by touching the 8 sensor All the lamps will go out If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Sensor control audible tones When selecting a function with the sensors an audible tone will sound briefly to confirm The audible tone can be deactivated m Touch the O sensor to switch the fan off m Touch the 4 and 8 sensors at the same time for approx 5 seconds until an audible tone sounds briefly The audible tone is now switched off for all functions m To reactivate the audible tone repeat the above process After the cooker hood has been disconnected from the mains electricity supply or after a power cut the audible tone is activated regardless of the last setting Cleaning and care Housing General notes The surfaces are susceptible to scratches and abrasions Please observe the following c
24. operation See also Warning and Safety instructions 27 Operation with Control module DSM 400 Connection to a light switch The control module can be used to switch on the hob lighting on the cooker hood and also to dim it depending on model via a light switch in the house The feature lighting cannot be operated via the control module Installation The control module is fitted in the tower after the cover plate has been unscrewed from the ceiling The control module is supplied with its own detailed operating and installation instructions 28 After Sales Service In the event of a fault which you cannot correct yourself or if the appliance is under guarantee please contact Your Miele Dealer or The Miele Customer Contact Centre see back cover for address When contacting your Dealer or the Contact Centre please quote the model and serial number of your appliance These are shown on the data plate ocated at the top of the canopy dai2298 Please note that telephone calls may be monitored and recorded for training purposes 29 Technical data Total connected load 632 W Fanmotor 500 W Canopy mechanism 4W Hob lighting 2x50 W Feature lighting 2x14W WAA 2 2 2 teats ceed Gada 230 V FICQUCNCY 22 esarutsnoan nego 50 Hz Fuse rating UK 13A Weighs assats aia p Lnn KAA 60 kg
25. pliance and hindering its smooth operation P gt The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care P Do not use a steam cleaner to clean this appliance Pressurised steam could reach the electrical components and cause a short circuit Correct installation gt Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob gt gt The minimum safety distances between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions section of this booklet must be maintained unless the hob manufacturer states that a greater safety distance is required If more than one appliance is fitted beneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance Warning and Safety instructions gt gt Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves gt All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants gt The appliance must not be connected to a chimney or vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used
26. s before reverting automatically to level 3 m To set this option both the fan and the hob lighting must be switched off m Touch the 53415 sensor for approx 10 seconds until the 1 sensor lights up m Touch in turn the sensor the 1 sensor and the sensor again The sensors for fan power levels 1 and 4 will flash if the automatic switch off for the Intensive setting is not activated m Touch the 4 sensor to activate auto matic switch off The 1 and 4 sensors will now light up constantly Touch the 1 sensor to deactivate the automatic switch off function m Touch the 53415 sensor to confirm your selection If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Operation Run on option 53415 It is advisable to leave the fan running for a few minutes after cooking has finished to neutralise any lingering odours in the air The fan can be set to switch off automatically after either 5 or 15 minutes m After cooking has finished press the run on option control 5 amp 15 whilst the fan is still running Press once The fan will switch off after 5 minutes the 5 lights up Press twice The fan will switch off after 15 minutes the 15 lights up To switch off the run on option touch the run on option sensor again The appliance will then not switch off automatically To switch the
27. the grease filter operating hours counter 19 Changing a halogen lamp 0 000s cece ETATE nina 20 Changing a fluorescent tube weavings eeu i baka daw ee yae babe Gee eae 21 Appliancedimensions 22 Safety distance between hob and cooker hood 22 Installation 22 eee 23 Installation instruCtiONS 23 Assembly PANS scauae cgi ieet ae endw reri veda noad ee RE Rea dine 23 Connection for air extraction 24 Electrical connection 26 Operation with Control module DSM 400 27 Connection to a window contact Switch 27 Potential free connection s y 4 24400240 Calan AE 27 Connection tora light Switeh t nese eee a ees eee ees eee eee 08 28 After Sales Service 29 Technical data 30 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle al
28. ust ducting to the floating bracket 23 Connection for air extraction Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room The cooker hood should be installed according to local and national building regulations Seek approval from the building inspector where necessary All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight as possible To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 200 mm If exhaust ducting with a diameter of less than 200 mm or if flat ducting is used the noise level of the cooker hood will increase and extraction will be less efficient Only reduce the diameter of the ducting if absolutely necessary e g where narrower ducting has already been installed Only use wide radius bends Tight bends reduce the air throughput of the cooker hood Only use smooth pipes or flexible hoses made from non flammable materials for extraction connection 24 When ducting is horizontal it must be laid to slope away at at least 1 cm per metre to ensure no condensate drains into the appliance dai04060 HEHEHEHE lf the exhaust air is to be ducted into a vent f
29. y the manufacturer of your cooking appliance 550mm above electric hobs and cookers 650 mm above an open grill or deep fat fryer 650 mm above gas hobs and cookers If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance a minimum safety distance of 760 mm must be maintained between the burner and the lower edge of the cooker hood See Warning and Safety instructions for further information Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safety instructions at the beginning of this booklet This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on oxygen from the same room to avoid the danger of toxic fumes building up Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Assembly parts Cm 0 CSS 8 screws 8 x 60 mm with 8 washers and 8 S 10 plugs to secure the cover plates to the ceiling The screws and plugs are for use in concrete ceilings only For other types of construction alternative suitable fixings will be required Make sure the ceiling is strong enough to bear the weight of the cooker hood 2 screws M4 x 8 mm for securing the tower oa 8 spacers to use in the event of an uneven ceiling 1 hose clip for securing the exha
Download Pdf Manuals
Related Search