Sanyo LNS-M02
Contents
1. Turn the projector on and operate Lens shift Zoom and Focus fully to check the Light Block Plates If Light Block Plate interferes with those operations check the Light Block Plate is set properly BE SURE TO CHECK FOR SAFETY After installing or replacing the lens be sure to check the following for safety 1 Check the lens is securely fixed 2 Check no part is missing and no mounting part is loose Some parts are not used for installation or replacement Keep these parts for later use Note Figures in this manual may differ from the actual product 52. any questions contact the dealers LIST OF CONTENTS Following parts are included in the packing e LENS 1 pc e LENS CAP Front and rear Each 1 pc e SCREW DRIVER 1 pc e INSTALLATION MANUAL 1 pc Z BE SURE TO CHECK FOR SAFETY After installing or replacing the lens be sure to check the following for safety 1 Check the lens is securely fixed 2 Check no part is missing or no mounting part is loose Some parts are not used for installation or replacement Keep these parts for later use Note Figures in this manual may be differ from the actual product aq E LENS REPLACEMENT AND INSTALLATION PROCEDURE Turn off the projector press the Main On Off This projector can use three 3 different types Switch to Off and unplug the AC power cord of Light Block Plates use the Light Block Plate from the AC outlet that corresponds to the appropriate optional lens Turn the Lens Mount Cover counterclockwise NOTE l and take it off by pulling forward See Fig 1 e Make sure the shape of the Light Block Plate is correct e Make sure the mark UP DOWN and FRONT BACK on Light Block Plates are correct and set them properly e Use the following Light Block Plate Light Block Plate Type FK2A 610 337 0064 S Lens Mount Cover Remove 2 Screws A and loosen 2 Screws B NOTE Slide the Top Cover forward to take off e The Light Block Plate FK2A is separated to the See Fig 2 upper and lower plates UP tad l
3. LCD PROJECTOR LENS MODEL NO LNS S04 LNS M02 LENS REPLACEMENT AND INSTALLATION PROCEDURES NOTES ON REPLACEMENT AND INSTALLATION The procedures and the needed pars for lens installation depend on the type of cabinet Before installing or replacing the lens make sure the type of cabinet and be sure to refer to the Installations corresponding with your projector When installing or replacing the lens make sure the Lens Model No matches with your projector Refer to the catalog or contact your sales dealer for the proper Lens Model No TYPE OF THE CABINET AND INSTALLATION PROCEDURES Refer to the Installation procedure corresponding to your projector and install the lens correctly See the chart below X For use the other models other than above cabinet contact your sales dealer Printed in Japan 1AA6P1P5925 IFTT Notes on Lens Installation and Replacement Lens installation and replacement should be performed by the qualified service personnel It should be followed by this procedure precisely Before attempt to replace the lens confirm the model number both the LCD projector and the lens and use the proper lens The lens cover is on the lens for protection Be sure to remove the lens cover before installation When installing or removing the lens be careful not to stain scratch or damage the lens When shipping the projector with the lens remove the lens before shipping the projector If you have
4. leftmost edge of the Seal on the projector and then turn the Lens Mount Cover clockwise and When the lens is attached to the projector and images adjust the position of the raised dot to the one of are being projected onto the screen the peripheral the projector See Fig 12 focus may be out of focus in some localized areas If this happens insert the one of three sizes of spacers in between the Lens Attachment and the lens to adjust the focus Inserting the Spacer corrects the distance on the Lens Adjustment and improves the diagonal focus NOTE f not mounted properly the Lens Mount Cover may fall causing hazards of injuly jane The corrected distance is determined by the thickness of the used spacers As a guide the distance is adjust Dot on the cabinet ed by approximately 30 mm for each 0 1 mm thickness 2 2 of the spacers S p _ __ Dot on the lens There are three types of spacers supplyed with the mount cover projector and there are four of each spacer type Use these spacers to correct the distance as required Spacer 1 Correction distance MARAJ Color Clear 30 mm for 60 inch pro Thickness 0 1 mm jection Spacer 2 Correction distance Color Black 60 mm for 60 inch pro Thickness 0 2 mm jection Spacer 3 Correction distance EREA Color Cream 90 mm for 60 inch pro Thickness 0 3 mm jection Screen 60 inch projection Lens Mount Cover c Fig 12
5. lyed with the projector There are two different types of Safety Clamps depending on the lens of the projector Please use Safety Clamp of the SC A type for this lens 1 Remove the screw holding the lens See Fig 9 1 2 Insert the removed screw to the Safety Clamp 3 Place the Safety Clamp in the location of the removed screw Make sure that the Safety Clamp is mounted to hold the Lens Lock Lever in the lock position Check the placement of the Safety Clamp See Fig 9 2 Safety Clamp SC A Part No 610 322 3742 Safety Clamp Lens Lock Lever Fig 9 1 Safety Clamp Attached Figure Safety Clamp SC A Part No 610 322 3742 Lens Lock Lever Fig 9 2 Install the Upper Light Block Plate into the guide of Lower Light Block Plate See Fig 10 Note e When installing the Upper Light Block Plate the Lower Light Block Plate should be lifted upward with your hand e Hang the ditch on Lower Light Block Plate to the Upper Light Block Plate e Make sure the mark UP DOWN and FRONT BACK on Light Block Plate is correct and set them properly Lower Plate Upper Plate NU pe Fig 10 Replace and fix the Top Cover with two 2 Screws A and 2 screws B See Fig 11 Top Cover A Fit the raised dot of the Lens Mount Cover to the FOCUS CORRECTION
6. t Upper Plate Top Cover Insert the lower Light Block Plate See Fig 4 Fig 2 Remove the Cover Plate by lifting upwards See Fig 3 Cover Plate t Remove the safety lens cap on the rear of the lens mounting side Insert the Lens Attachment and secure with the four 4 screws supplied See Fig 5 Connect the Lens Motor Lead to the socket on the top loght of the Lens Attachment See Fig 6 Screw Driver od Fig 5 Lens Attach nent supplied with the optional lens supplyed wi h the projector Part No 610 275 6029 Grasp release lock the Lens Lock Lever and turn it fully upward See Fig 7 Install the Lens into the projector Grasp the Lens Lock Lever and turn the Lever fully downward until lever is Locked clicked position properly See Fig 8 After installing the lens make sure the lens is not loose and properly installed LENS LOCK RELEASE Grasp unlock Lens Lock Lever and pull upward Lens Attachment 01 POA LNA 01 Part No 610 303 8742 Lens Attachment LENS LOCK Lens Motor Lead Grasp unlock Lens Lock Lever and fully pull down ward until it is locked clicked To ensure that the lens is securely fixed to the projector when mounting be sure to attach the Safety Clamp supp
Download Pdf Manuals
Related Search