Home

Panasonic BL-C101CE

image

Contents

1. 2 Turn the mounting screw to attach the camera 3 Adjust the angle then fasten the position lock Stand tripod mounting hole Era oF CS ee R Flexible stand 7 Tripod Mount Do not use a tripod screw with a thread of 6 mm 1 4 inch or more This may damage the stand tripod mounting hole The camera cannot be mounted depending on the shape of the camera platform Stand tripod mes mounting hole jk B AUY A Tripod Th customer provided y U Ceiling Wall Mount 1 Secure the safety wire to the camera using screw B included and washer S included Make sure you attach the safety wire when mounting the camera to prevent the camera from falling Safety wire aS Washer S Te Screw B 2 Connect a LAN cable to the camera Insert the LAN cable until it clicks into to place 3 Mount the flexible stand firmly to the ceiling or wall with screw A included Do not drive the screws into a soft material Drive the screws into a secure area of the wall such as a wall stud otherwise the camera may fall and be damaged Use screws that are suited for the type of material the camera is mounted to Allow sufficient space between the ceiling or wall and the flexible stand to turn the position lock Make sure the flexible stand is firmly mounted on a wall or ceiling stud 25 mm 1 inch and greater etc When there is no stud apply a board on the other side of the ceiling or
2. D FACTORY DEFAULT A Indicator D FACTORY DEFAULT B Lens RESET button B Lens RESET button C Microphone E Serial number label C Microphone E WIRELESS WIRED F eee Mounting A D G a 4 ole po G External INPUT Ep i ele G Serial number label i ee ERIN el e H Ara pog Mounting ole EF External I O interface B _ J DC IN jack K Hook for AC adaptor cord See 1 1 Understanding the Camera Indicator in the Troubleshooting Guide on the CD ROM for indicator meaning Connections Connect the camera to your router and to the power outlet as described below e Before proceeding confirm that your PC is connected to your router and can access the Internet Also confirm that your router s UPnP feature is enabled Most routers have UPnP turned off by default Refer to the operating instructions included with your router or to the Panasonic Network Camera website http panasonic net pcc support netwkcam for more information BL C101 e Use a LAN cable that is no more than 30 m 98 feet 5 inches long to connect the camera and the power transfer unit Connect the LAN cable to the camera and the power transfer 4 3 Connect the AC adaptor to the power unit transfer unit and plug the AC adaptor into the power outlet e Confirm that the indicator turns green after about 1 minute If it does LAN cable Cat 5 straight cable To the power 4 outlet not turn green see 1 2 Camera A For BL
3. Indicator Issues in the C101CE Troubleshooting Guide on the CD Power transfer unit BL C101E ROM 5 use an AC cord 4 Connect the LAN cable to the AC adaptor router and the power transfer unit i LAN cable e When you operate the camera the power outlet should be near the camera and easily accessible e Use only specified Panasonic AC adaptor Order No PQLV206Y for BL C101A PQLV216CE1Z for BL C101CE BL C101E e The camera may become warm This is normal BL C121 Confirm that the WIRELESS WIRED switch on the side of the camera is set to WIRED Connect the LAN cable to the camera and the router WIRELESS WIRED switch Connect the AC adaptor cord to the DC IN jack 00O OO Plug the AC adaptor into the power outlet e Confirm that the indicator turns green after about 1 minute If it does not turn green see 1 2 Camera Indicator Issues in N Guide on the CD Router To the power outlet wng aeo lt N For BL 32 a LANGABIE Eon Cat 5 straight cable When you operate the camera the power AC cord outlet should be near the camera and easily accessible e Use only specified Panasonic AC adaptor Order No PQLV206Y for BL C121A PC AC adaptor PQLV216CE1Z for BL C121CE BL C121E The camera may become warm This is normal After the camera
4. an external device used in the camera circuit All wiring should be performed by a using the output buttons in the camera s operation bar for example qualified electrician Incorrect wiring could damage the camera and turning a light on or off cause a fatal electric shock e This terminal s behavior can be changed see 7 4 Controlling the e External devices connected to the camera s output terminals cannot our cco BL C121 Only in the Operating Instructions be controlled in the event of a network error or failure Keep this in BL C121 e This terminal is an open collector circuit The maximum drawing ming When conniecing daar loek neal omining devicas OT Oihar only current is the same as terminal 4 Do not exceed the voltage of devices that may be dangerous if they cannot be controlled BL terminal 4 C121 only DC power output terminal 4 e DC 8 V 10 V Maximum load is 100 mA Note e If excessive force is used when disconnecting wires with pointed objects from the external I O interface terminals may become damaged or the interface may be pushed inside the camera body and become unusable For BL C121 Notes About Wireless Communication The radio wave range may decrease depending on the surrounding environment or existence of obstacles If obstacles such as the following are placed between a camera and a router radio waves will weaken Therefore even if the distance between the camera and router is short the frame rate may dec
5. s indicator turns green you may set up the camera Continue by following the procedure described in the included Setup Guide e Ifthe indicator does not turn green see 1 2 Camera Indicator Issues in the Troubleshooting Guide on the included CD ROM Connecting External I O interface The camera s external I O interface allows you to connect a device such as a sensor or motion detector that can be used to trigger the camera s image buffering and transferring features see Section 2 Using Triggers to Buffer and Transfer Images in the Operating Instructions on the CD ROM as well as the detection notification sound feature see Section 1 2 7 Detection Notification Sound in the Operating Instructions on the CD ROM BL C101 Circuit Diagram Example External INPUT interface ee BL C121 only BL C121 DC 8 V 10 V Caution e The external I O interface is not capable of connecting directly to devices that require large amounts of current In some cases a Terminal Description custom interface circuit customer provided may have to be used 1 GND terminal Serious damage to the camera may result if a device that exceeds IN External sensor input The camera can be triggered by either an open its electrical capability is connected to the external I O interface circuit or a GND short circuit e Low voltage current circuits and high voltage current circuits are External device control output Allows you to control
6. Panasonic l n sta l l ati O n G u ide Please read this document before using the product and save this document for future reference Panasonic Network Camera Website N etwo rk C amera Indoor Use Only http panasonic net pcc products netwkcam Model No B L C 1 0 1 Wired Type B L C 1 2 1 Wireless Wired Type This manual is written for both the BL C101 Wired Type and BL C121 Wireless Wired Type Available features and operations vary slightly depending on the model You can confirm the model no of your camera by checking the model no printed on the front of the camera Model number suffixes A CE and E are omitted from the following model numbers shown in this document unless necessary BL C101A BL C101CE BL C101E BL C121A BL C121CE BL C121E Please read the included Important Information before proceeding Complete Operating Instructions and all other documentation can be found on the included CD ROM This document Installation Guide explains how to physically connect the camera to the power supply and network as well how to mount or place the camera for regular use e The Setup Guide describes how to set up the camera so that it can be accessed using a PC e Refer to the Operating Instructions on the CD ROM for details regarding the camera s features e Refer to the Troubleshooting Guide on the CD ROM if you have any problems configuring or using the camera Abbreviations
7. UPnP is the abbreviation for Universal Plug and Play The Network Camera is referred to as the camera in this document The Setup CD ROM is referred to as the CD ROM in this document Installation Procedure Overview The following is an overview of the steps required to install and setup the camera All steps are explained in this document unless otherwise noted Preparation gt Camera Diagram Connections Setup Mounting Confirm that you have all the Make sure you know the names Connecting the camera to your Setting up the camera Mounting or placing the camera items required for installation of the camera s physical network and to the power outlet described in the included Setup features Guide This involves configuring the camera so that it can be accessed from a PC Preparation 1 Confirm the following items are included in the camera s packaging Main Unit 1 pc Screw A BL C101 6 pcs BL C121 Washer S 1 pc The appearance of your 4 pcs Order No XWG26D12VW camera depends on which PPP Order No XTB4 20AFJ Used when securing the safety model you have purchased PPP Used for wall mounting the camera wire to the camera BL C101 BL C121 AC Adaptor 1 pc Screw B 1 pc Washer L 1 pc Order No PQLV206Y Order No XTB26 10GFJ Order No XWG4F16VW Cord Length About 3 m L Used for securing the safety wire to Used when securing the safety 9 feet 10 inches the camera wire to the wa
8. ll BL C101A BL C121A Flexible Stand 1 pc Order No PNKL1008Z Used to attach the camera to the wall Order No PQLV216CE1Z Safety Wire 1 pc Cord Length About 3 m Order No PQME10080Z 9 feet 10 inches Used to secure the camera when wall BL C101CE BL C101E BL mounting it C121CE BL C121E AC Cord 1pc for BL Important Information 1 pc Setup CD ROM 1 pc C101CE BL C101E BL Installation Guide Order No PQQX15704MCD C121CE BL C121E this document 1 pc Contains the Setup Program Order No PFJA02A006Z Setup Guide 1 pc needed to configure the camera Cord Length About 1 8 m as well as the camera s 5 feet 11 inches documentation BL C101CE BL C121CE See the included Important Information for a description of each document Order No PSJA1106Z BL C101 Only Cord Length About 1 8 m 5 feet 11 inches a Power Transfer Unit 1 pc BL C101E BL C121E 4 Order No PNWP3C160A gt Used to power the camera 2 You will need the following additional items to install and configure the camera aPC see the system requirements in the Important Information document For BL C101 2 LAN cables CAT 5 straight cable For BL C121 a LAN cable CAT 5 straight cable a router Panasonic Communications Co Ltd 2008 PNQX1566YA KK0908CM1108 Camera Diagrams BL C101 BL C121 Front View Rear View Front View Rear View A Indicator
9. rease or images may not be displayed e A metallic door or shutter e A wall with an insulation material that contains aluminum foil A wall made of tin A wall made of concrete stone or brick e Fireproof glass e Several walls separated by open space e A steel shelf In the example below wireless communication between the camera and the wireless router is impaired due to steel doors or reinforced concrete walls between the camera and the wireless router Wireless antenna is built in the camera Position the camera away from obstacles such as steel doors or reinforced concrete walls Mounting the Camera The camera illustrations in this document depict the BL C121 Caution Do not drive the screws into a soft material Drive the screws into a secure area of the wall such as a wall stud otherwise the camera may fall and be damaged e Make sure you attach the safety wire when mounting the camera to prevent the camera from falling e Use screws that are appropriate for the material of the wall e The included screws are for use with wooden walls only e The camera is intended for indoor use only and should not be mounted outdoors To ensure that camera images are displayed properly do not mount the camera on an incline Mount the camera so that it is perpendicular to the floor Do not mount the camera upside down Flexible Stand Mount 1 Loosen the position lock located on the rear side of the flexible stand
10. rs for 4 mm 3 16 inch diameter screws for mounting 1 Place the flexible stand on the ceiling or wall where you plan to mount the flexible stand and mark the points where you are going to make holes 2 Make holes with an electric drill Insert anchors customer provided into the holes and use a hammer to make them flush with the wall e Mortar ceilings or walls break easily when drilling Be careful of pieces of mortar which may become loose and fall Drill for concrete in case of tile use a drill for tile Of 3 Mount the flexible stand using the screws For BL C101 Only Connecting to the power transfer unit 8 Connect a LAN cable to the power transfer unit and to the switching hub router etc The power transfer unit can be fixed in place with 2 pieces from screw A included 4 mm x 20 mm 3 16 inch x 13 16 inch LAN Cable 9 Connecta LAN cable from the camera to the power transfer unit 10 Connect the AC adaptor to the power transfer unit and plug the other end into the power outlet The camera will activate To the power outlet For BL C101CE BL C101E use an AC cord Hook for AC adaptor
11. wall to make sure the camera does not drop m Ceiling m Wall DSS Wy At least 25 mm CZA 1 inch i an Allow sufficient space At least 25 mm 1 inch re between the ceiling y te and the flexible stand oy Screw A 3 pcs J Allow sufficient space ee lt between the wall and da Screw A the flexible stand 3 pes 4 Loosen the position lock located on the rear side of the flexible stand and turn the mounting screw to attach the camera m Ceiling m Wall Stand tripod mounting hole Position lock Mounting screw Stand tripod mounting hole Position lock Mounting screw Indicator 5 Adjust the camera position and tighten the position lock m Ceiling m Wall Position lock 6 Connect all necessary cables AC adaptor LAN etc to the camera dress the cables neatly and secure with tape customer provided m Ceiling m Wall Tape customer provided 7 Secure the safety wire to the ceiling or wall using screw A included and washer L included e Leave some slack in the safety wire as shown e Make sure the safety wire is firmly mounted on a wall or ceiling stud 25 mm 1 inch and greater etc When there is no stud apply a board on the other side of the ceiling or wall to make sure the camera does not drop m Ceiling m Wall c gt Washer L amp ScrewA esis wire e a Soe Washer L When mounting on a mortar or concrete surface Prepare ancho

Download Pdf Manuals

image

Related Search

Related Contents

GOTO GOTO GOTO GOTO GOTO GOTO  取扱説明書  beauty face  電動ワイヤーアッパー  Philips 21" REAL Flat Stereo TV w/ Crystal Clear  Franck LAURENT  KX - KK - i-TES  Manual sun2go.indd  user manual  13" 4A String Trimmer Manual (English)  

Copyright © All rights reserved.
Failed to retrieve file