Supermicro AOC-STGN-I2S
Contents
1. lt value gt For 2 6 kernels the insmod command can be used if the full path to the driver module is specified For example insmod lib modules lt KERNEL VERSION gt kernel drivers net ixgbe ixgbe ko In addition when using 2 6 based kernels make sure that older ixgbe drivers are removed from the kernel before loading the new module To do this use rmmod ixgbe modprobe ixgbe Assign an IP address to the interface by entering the following where x is the interface number ifconfig ethx lt IP_address gt netmask lt netmask gt Verify that the interface works Enter the following where lt P_address gt is the IP address for another machine on the same subnet as the interface that is being tested ping lt IP_address gt 3 3 AOC STGN i2S Add on Card User s Manual Notes 3 4 Disclaimer The products sold by Supermicro are not intended for and will not be used in life support systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicr2. 1 0 Release Date February 2 2010 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Portions of this document Intel Corporation Copyright 2009 by Super Micro Computer Inc All rights reserved Printed in the United States of America Introduction Overview This manual is written for system integrators PC technicians and knowledgeable PC users who intend to integrate Supermicro s AOC STGN i2S add on card Product Features The AOC STGN i2S offers the following features Intel 82599ES 10 GbE Controller e Low profile standard form factor e PCI E x8 Gen 2 5 GT s e Intel QuickData Technology DMA engine that enhances data acceleration and lowers CPU usage e Direct Cache Access DCA to avoid cache misses Tx Rx IP SCTP TCP and UDP checksum offloading capabilities IPv4 IPv6 e Supports Virtualization features such as VMDq Next generation VMDq 64 queues per port and PC SIG SR IOV implementation Preboot Execution Environment PXE support e Simple Network Management Protocol SNMP and Remote Network Monitoring RMON statistic counters iSCSI boot Intel PROSet Utility for Windows Device Manager e ROHS compliant 6 6 Supported Operating Systems The AOC STGN i2S supports the following Operating Systems OS Windows 2008 2003 2000 Linux e VMW
3. Connectors and Pin Definitions Number Description 1 LAN Connector Ports 2 LAN Port LEDs 3 Intel 82599ES 2 1 AOC STGN i2S Add on Card User s Manual LAN Ports LAN ports allow the Add on card to connect a maximum of two network cables SFP connectors Each LAN port provides up to 10 gigabits per second connection speed and require SFP DAC twin axial cables up to 10 meters The ports are designated Port 1 and Port 2 LAN Port LEDs Each LAN port has two corresponding dual color LED s which indicate activity ACT and connection speed LNK See Section 2 2 for further details 2 2 LED Indicators Figure 2 2 LED Indicators Port 1 Port 2 LNK LED LNK LED Port 1 Q Q Port 1 Port 2 ACT LED ACT LED Figure 2 2 displays LED indicators on the AOC STGN i2S add on card These dual color LEDs are described below in Table 2 2 Table 2 2 LAN Port LED Colors LED Color Definition Green 10 Gb link speed LNK Yellow 1 Gb link speed ACT Blinking Green Activity 2 2 Chapter 3 Installation 3 1 Before Installation Before installation do the following 1 Power down the system 2 Remove the power cord from the wall socket 3 Use industry standard anti static equipment such as gloves or wrist strap and or an environment that prevents accidental electrostatic discharge 4 Familiarize yourself with the server motherboard and or chassis documentation 5 Conf
4. SUPERMICRO AOC STGN i2S Add on Card User s Manual Revison 1 0 AOC STGN i2S Add on Card User s Manual The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by t
5. are ESX Server Required Cables The AOC STGN i2S requires the following cables e SFP direct attached twin axial cabling up to 10 meters Dual LC Fiber optic connections SR up to 300 meters AOC STGN i2S Add on Card User s Manual An Important Note to Users All images and layouts shown in this user s guide are based upon the latest PCB Revision available at the time of publishing The card you have received may or may not look exactly the same as the graphics shown in this manual Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carton and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online at http Awww supermicro com support rma Whenever possible repack the add on card in the original Supermicro box using the original packaging materials If these are no longer available be sure to pack the add on card in an anti static bag and inside the box Make sure that there is enough packaging material surrounding the add on card so that it does not become damag
6. ed during shipping This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems Contacting SuperMicro Headquarters Address Tel Fax Email Web Site Europe Address Tel Fax Email 9 Asia Pacific Address Tel Fax Web Site Technical Support Email Tel Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A 1 408 503 8000 1 408 503 8008 marketing supermicro com General Information support supermicro com Technical Support www supermicro com Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands 31 0 73 6400390 31 0 73 6416525 sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C 886 2 8226 3990 886 2 8226 3991 www supermicro com tw support supermicro com tw 886 2 8228 1366 ext 132 or 139 AOC STGN i2S Add on Card User s Manual Notes Table of Contents Chapter 1 Safety Guidelinee 1 1 1 1 ESD Safety Guidelines nereeenn
7. enenenn 1 1 1 2 General Safety Guideline nenen 1 1 1 3 An Important Note to Users eesnssenenenenenennnennnnenenennn 1 1 Chapter 2 Connectors Jumpers and Indicators 2 4 2 1 Front Connectors and Pin Definitione 2 1 LAN FR Fi ss Xesi A A 2 2 LAN Port LEDS ad 2 2 2 2 LED Indicators an r a e a a e ERa a 2 2 Chapter 3 Installation 3 1 3 1 Before Installation kin binn lel kak lan e 3 1 3 2 Hardware Installation oococnconcccncnooocoonconnoononnnonconnornnonnonnninos 3 1 3 3 Windows 2003 2000 Installation 3 1 3 4 LINUX Instalati ienis Au k ya kadan kn asad daka i egs 3 2 Build a Binary RPM Package occccoocccnonccononccononcnononcnnoncnnonano cnn non nnnnarnncnnns 3 2 Manually Build the Driver E E kk kek kk kk Ke KS 3 2 AOC STGN i2S Add on Card User s Manual Notes vi Chapter 1 Safety Guidelines To avoid personal injury and property damage carefully follow all the safety steps listed below when accessing your system or handling the components 1 1 ESD Safety Guidelines Electric Static Discharge ESD can damage electronic components To prevent damage to your system it is important to handle it very carefully The following measures are generally sufficient
8. he laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate for further details WARNING HANDLING OF LEAD SOLDER MATERIALS USED IN THIS A PRODUCT MAY EXPOSE YOU TO LEAD A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM Manual Revison
9. ion To install the driver to a Linux system do the following Build a Binary RPM Package 1 Run rpmbuild tb lt filename tar gz gt 2 Replace lt filename tar gz gt with the specific filename of the driver NOTE For the build to work properly the currently running kernel MUST match f the version and configuration of the installed kernel sources If you have just recompiled the kernel reboot the system now Manually Build the Driver 1 Move the base driver tar file to the directory of your choice For example home username ixgbe or usr local src ixgbe 2 Untar unzip archive tar zxf ixgbe x x x tar gz 3 Change to the driver src directory cd ixgbe x x x src 4 Compile the driver module make install The binary will be installed as lib modules KERNEL_VERSION kernel drivers net ixgbe ixgbe k o The install locations listed above are the default locations They might not be correct for certain Linux distributions For more information see the distrib txt file included in the driver tar 3 2 Chapter 3 Installation NOTE IXGBE_NO_LRO is a compile time flag The user can enable it at compile time to remove support for LRO from the driver The flag is used by 5 adding CFLAGS_EXTRA DIXGBE_NO_LRO to the make file when it s being compiled make CFLAGS_EXTRA DIXGBE_NO_LRO install Load the module For kernel 2 6 x use the modprobe command modprobe ixgbe lt parameter gt
10. irm that your operating system includes the latest updates and hotfixes 3 2 Hardware Installation To install the add on card do the following 1 Remove the server cover and if necessary set aside any screws for later use 2 Remove the add on card slot cover If the case requires a screw place the screw aside for later use 3 Position the add on card in the slot directly over the connector and gently push down on both sides of the card until it slides into the PCI connector 4 Secure the add on card to the chassis If required use the screw that you previously removed 5 Attach any necessary external cables to the add on card 6 Replace the chassis cover 7 Plug the power cord into the wall socket and power up the system 3 3 Windows 2003 2000 Installation Use the following instructions to install the drivers to a supported Windows Operating Systems The controller comes with a driver on the CD ROM CDR NIC 1 Run the CDR NIC If you do not have a product CD ROM then download drivers from the Supermicro Support Website and transfer them to your system 2 The SUPERMICRO window appears Click on the computer icon next to the product model 3 1 AOC STGN i2S Add on Card User s Manual NOTE If the FOUND New HARDWARE WIZARD screen is displayed on your r4 system click CANCEL 3 Click on NSTALL DRIVERS AND SOFTWARE 4 Follow the prompts to complete the installation 3 4 Linux Installat
11. o harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale AOC STGN i2S Add on Card User s Manual
12. to protect your equipment from ESD Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing a component from the antistatic bag e Handle the add on card by its edges only do not touch its components peripheral chips memory modules or gold contacts e When handling chips or modules avoid touching their pins Put the card and peripherals back into their antistatic bags when not in use 1 2 General Safety Guidelines Always disconnect power cables before installing or removing any components from the computer Disconnect the power cable before installing or removing any cables from the system Make sure that the add on card is securely and properly installed on the motherboard to prevent damage to the system due to power shortage 1 3 An Important Note to Users All images and layouts shown in this user s guide are based upon the latest PCB Revision available at the time of publishing The card you have received may or may not look exactly the same as the graphics shown in this manual 1 1 AOC STGN i2S Add on Card User s Manual Notes 1 2 Chapter 2 Connectors Jumpers and Indicators 2 1 Front Connectors and Pin Definitions Connectors are used to attach the add on card to the system s mainboard Figure 2 1 AOC STGN i2S Add on Card Front Connectors and Jumpers Table 2 1 lists the add on card s front connectors Table 2 1 Front
Download Pdf Manuals
Related Search