Caliber MCD 785
Contents
1. Screen Type TFT Liquid Crystal Display active matrix Resolution 960 W x 324 H DVD CD SECTION Compatible Disc Format Signal to Noise Ratio Dynamic Range Frequency Response VIDEO SECTION Color System Video Output Video Input AUDIO SECTION Line out level Line out Impedance AUXILIARY INPUT SECTION Input Maximum Voltage Input Impedance GENERAL Fuse Operating Temperature Unit Mounting Angle See Disc Note for more details description gt 90 dB gt 90 dB 20Hz to 20Khz 3dB NTSC PAL Composite 1 0 Vp p 0 2 75 ohm Composite 1 0 Vp p 0 2 75 ohm 2 Volt 200 ohm 1200 mV 4 7k ohm 15 Mini ATM Type 09C to 50 C lt 30 BER Usile TECHNOLOG TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your nearest service dealer Symptom Cae Solon _ No power Disc cannot be loaded or ejected The operation keys do not work The radio does not work The radio station automatic selection does not work The car ignition is not on If the power supply is properly connected to the car accessory terminal switch the ignition key to ACC The fuse is blown Replace the fuse Presence of CD disc inside Remove the disc in the player then the player put a new one Inserting the disc in reverse Insert the compact disc with the direction label facing upward C2. User has 5 seconds to use the encoder volume knob to adjust the desired Treble center frequency to 0 2 12 5K Hz I 5KHz or 17 5KHz BALANCE User has 5 seconds to use the encoder volume knob to adjust the Balance between the right and left speakers from R12 full right to 112 full left represents an equal balance between the right and left speakers FADER User has 5 seconds to use encoder volume knob to adjust the Fader between the front and rear speakers from R12 full rear to F12 full front C00 represents an equal balance between the front and rear speakers TUNER OPERATION 19 BAND BUTTON BAND Press BAND to change between FM bands and AM MW bands 20 amp 21 TUNING UP DOWN BUTTON 1 MANUAL TUNING Press the Up Tuning P9 or Down Tuning M button for more than 3 seconds to move the radio frequency number up or down by one step AUTO SEEK TUNING Press the Up Tuning PPI or Down Tuning M button for less than 3 seconds to move to next station automatically 12 17 PRESET STATIONS BUTTONS Six numbered preset buttons store and recall stations for each band I I AUTOMATICALLY STORE PRESET SCAN AS PS Automatically select 6 strong stations and store them in the current band Select a band if needed Press AS PS button for more than three seconds The new stations replace stations already stored in that band PRESET SCAN Scan stations stored in the current band Select band if needed
3. Press AS PS button for less than 3 seconds The unit will pause for ten seconds at each preset station Press AS PS button again to stop scanning when the desired station is reached STEREO The unit will automatically pick up a stereo signal when available When in stereo mode the ST icon appears in the display When no stereo signal is available the unit will automatically revert to mono operation and no icon will be displayed RDS OPERATION RDS FUNCTIONS The unit is equipped with the following RDS function AF Alternative Frequencies CT Clock Time EON Enchanced other Network Program identifications PS Program service name PTY Program Type REG Regional Change TA Traffic Announcement TP Traffic program I AF FUNCTION By pressing AF button lt 3 seconds to select AF ON OFF AF icon will light up on the LCD Under AF mode if the tuned in station signal is getting weak the unit will automatically switches to a different frequency on the same network with stronger signal Ly Factory Default setting is AF ON 2 TA FUNCTION By pressing T button 3 seconds to switch on TA standby mode The TA icon will light up on the LCD In the stand by mode when a traffic announcement broadcast starts the traffic announcement broadcast will be received as top priority regardless of the function mode When a traffic announcement starts TRAFFIC INFO will show on the LCD
4. Time Title Chapter 2 Press the UP DOWN direction buttons to select the type of search time search or Chapter track title search Select Time to jump to a spot on the disc and enter the time in units of hours minutes and seconds hh mm ss ZIBER Select Title Chapter to jump to the beginning of a specific chapter within a specified title DVD only and enter the title and chapter numbers with the number pad and LEFT RIGHT direction buttons as follows Track Select Track to jump to the beginning of a specific track within a non DVD disc and enter the track number with the number pad as follows 33 ZOOM BUTTON Press ZOOM during normal slow or still playback 2 Pressing the ZOOM button repeatedly increases the magnification level Three magnification levels are supported On each press of ZOOM the OSD will flash the following 23 3 Pressing the direction buttons causes the zoom point to shift allowing the zoomed image to be panned Some discs may not respond to the zoom feature 2 Zooming does not work on subtitles or menu screens included on DVDs 3 The magnification level and number of available levels vary depending on the TV TYPE selection in the Setup Menu 37 TITLE Press TITLE to invoke Title Menu DVD only dependent on authoring of disc 2 Press direction buttons to highlight selected Title Menu entry 3 Press OK or PLAY to select the highlighted entry If th
5. amp Remote control is defaulted to control the FRONT source s function operation When DUAL ZONE is turned ON the Mode button is used to change between the Front Source amp Rear Source Press the mode button repeatedly to change between Front and Rear The LCD will display the Rear Source mode for 10 seconds User has 10 seconds to make the desired operation on the Rear Source s function on the Front Panel or Remote The LCD will automatically switch back to the Front Source after 10 seconds And the Front Panel and Remote now is resumed to operate for Front Source s function again THE DEFAULT SETTING WHEN DUAL ZONE IS When DUAL ZONE is turned on the audio output will be muted for about second The default source mode for Front ZONE is Tuner amp for Rear ZONE is DVD The default Volume level is 12 for both Front amp Rear ZONE audio output or the Volume Level set as VOL PGM Level set in the Menu The LCD display is defaulted to display the Front Mode When Dual Zone is ON the audio functions Bass Treble Middle Balance Fader Sub woofer iX bass will not be available THE DEFAULT SETTING WHEN DUAL ZONE IS IN OFF MODE The default audio output reverts to what the user selected for the FRONT Zone source when DUAL ZONE IS OFF For example When the DUAL Zone is ON user has selected DVD for Front ZONE amp Tuner for Rear ZONE Once DUAL ZONE is turned OFF Audio Output f
6. press the TA button can cancelled the broadcast reception while a traffic announcement broadcast is being received The unit will go back to the previous mode and TA goes into stand by mode again When the TP icon is not light up for 60 seconds A beep Alarm tone is heard and the LCD will show Lost TP TA TA seek will automatic activate and searches to another TA station 3 PTY FUNCTION Pressing PTY TA button more than 3 seconds to go into PTY select mode The user now has 5 seconds to select the desired PTY item by using encoder volume knob Once selected the PTY item user have 5 seconds to press AUDIO CENTER or TUNE UP gt gt or TUNE DOWN lt lt buttons lt 3 seconds to seek for the selected PTY item The LCD will display PTY SEEK If no station with the selected PTY broadcast can be received the LCD will display No Match PTY for 5 seconds then returns to the previous mode User can store his favorite PTY into the preset memory MI to M6 After selected a PTY item long press any one of the preset memory button can store the selected PTY To recall the stored PTY item switch on PTY mode then press preset memory lt 3 seconds the unit will automatically search the stored PTY station in the preset memory 5 Music Group POP ROCK EASY LIGHT CLASSICS OTHER CULTURE SCIENCE VARIED Speech Group NEWS AFFAIRS INFO TEST ALARM SPORT EDUCATE DRAMA JAZZ COUNTRY WEATHER FINANCE CHILDREN NATION OLDIES SOC
7. Most widescreen DVDs will not allow pan amp scan conversion If 4 3 PS is selected on these DVDs letterboxing will be used instead If 16 9 is selected and a 4 3 TV is connected 16 9 content will appear distorted during playback objects look thin TV System NTSC or PAL The Video setting allows the user to select the TV standard DVD and VCD SVCD only The following options are available English Menu OSD is in English factory default Frangais Menu OSD is in French Espa ol Menu OSD is in Spanish Deutsch Menu OSD is in German Italiano Menu OSD is in Italian Portugu s Menu OSD is in Portuguese Turk e Menu OSD is in Turkish Russian Menu OSD is in Russian Lj Some DVDs may not include the pre selected language In this case the unit will automatically display menus in the disc s initial language setting VIDEO SETTINGS Using the Up Down buttons move to the Video The Player s Video settings will appear NTSC TV is NTSC PAL content is played at NTSC resolution and frame rate factory default PAL TV is PAL NTSC content is played at PAL resolution and frame rate AUTO f the content is PAL the output is PAL If the content is NTSC the output is NTSC Lg Playing PAL DVDs with TV SYS set to NTSC is not allowed The OSD will indicate OSD PAL to NTSC error RATING SETTINGS Using the Up Down buttons move to Rating the Rating settings will appear Set Password 2 Use th
8. Volume Ey Fast Fast Fast Up Forward Forward Forward Tune Fast Fast Fast Down Backward Backward Backward e J gue gue o une o az _ go Pause Play pig fse j Stop Stop 2 3 4 8 amp XX9 9X 099999 9909 OPERATIONS Long Short Long Short Long Short Long Press Press Press Press Press Press Press Memory Track NO Access Numeric 5 5 File NO Access Track NO Access Sub W Track NO Access N meric 7 File NO Access Track NO Access File NO Access Track NO Access File NO Access Band Track NO Access Numeric 0 File NO Access Track NO Access File NO Access Numeric 10 VCD PBC DVD DVD MENU oe Repeat Off Repeat Off Repeat Track Repeat Chapter peat Track E Repeat Title lt Se Lamp od do o po me ep _ _ 40 NERA _ _ ENS ee ELI BER BASIC OPERATIONS 3 PANEL RELEASE BUTTON REL Press this button to remove the control panel I POWER ON OFF BUTTON Long press the POWER button or Short Press any other button on the front of the unit except the Open Eject to turn On the unit Long press the POWER button to turn Off the unit I MUTE BUTTON Short Press the MUTE button to mute the audio output and Mute will appear on the display Press the mute button again to restore the audio output to the previous level Please refer to the related descript
9. is only function with the Mobile Phone has already been paired with the unit before The LCD Display will displayed RECONNECT during the connecting period If the re connection is successful the LCD Display will display RECONNECT OK and the unit will switch back to the previous mode automatically If the re connection failed the LCD Display RECONNECT FAIL will display and the unit will switch back to the previous mode automatically gt gt The unit will be Auto Re Connection by following operation Every time turn the ignition key from off to on the unit will Auto re connect with the mobile phone one Dis Connection of the Bluetooth System The unit have a option function for user to disconnect the Blue Tooth system with the unit The unit can be Dis connected by the following methods Access into MENU RECONNECT mode then rotate the encoder volume knob to select the DISCONNECTION mode Ly Pls see MENU Operation for more details of how to access into MENU mode Once the DISCONNECT is display on the LCD press the AUDIO button to activate the manual Re Connect mode The LCD Display will displayed DISCONNECT during the Dis connecting period If the Dis Connection is successful the LCD Display will display DISCONNECT And the unit will switch back to the previous mode automatically INCOMING CALL Answering an incoming call When there is an incoming call the LCD Display w
10. over the logo background When the player has finished searching it will automatically start Slideshow mode from the first picture all pictures will be displayed in their file folder order Default Slideshow interval between pictures is five seconds PAUSE NEXT BACK and NUMERIC selection and navigation keys work the same as in other operations THUMBNAIL VIEW Press the TITLE key to get a thumbnail view Nine pictures 3x3 will be displayed on the screen beginning with the last viewed picture on the upper left part of the screen The first thumbnail image will be highlighted with a blue border 2 Use the direction keys LEFT RIGHT UP DOWN to select another thumbnail 3 Use the NEXT BACK keys to move to another thumbnails page 4 Use the OK key to switch to the playback mode to start the image last highlighted in the thumbnail view EI BER DVD OPERATION DVD OPERATION REMOTE CONTROL 21 2 EECT BUTTON 2 Press the EJECT button to eject the disc or loading the disc 17 PLAY PAUSE PII Press PAUSE to pause playback 2 Press PAUSE to single step forward to the next picture in the video DVD and VCD only 3 Press PLAY to resume normal playback 18 STOP RB Press STOP to stop playback and show the logo screen The player memorizes the location where playback is stopped 2 Press PLAY to resume playback from the location where playback is stopped DVD VCD I I VCD 2 0 and audio CD 3 Pressing STOP twi
11. the unit will automatically enter into STOP mode User can press play button to start the DISC playback again when in the STOP mode 12 PAUSE PLAY BUTTON 1P Il Press PAUSE to pause playback still mode The sound from the disc is muted during still mode 2 Press PLAY to resume normal playback 13 STOP BUTTON 2 STOP Press STOP to stop playback and show the logo screen The player memorizes the location where playback is stopped 2 Press PLAY to resume playback from the location where playback is stopped DVD VCD 1 1 VCD 2 0 and audio CD 3 Pressing STOP twice is resume playback from the beginning of the disc I4 REPEAT BUTTON 3 RPT Press REPEAT button less than 3 seconds to repeat play the current song and keep on repeat Playing the current song until the repeat play is disabled To disable current song repeat play press REPEAT button less than 3 seconds 15 RANDOM BUTTON 4 RDM Press RANDOM button less than 3 seconds is random play all songs on the disc To disable all songs random play press RANDOM button less than 3 seconds JPEG CD OPERATION DVD R F5 JPEG 97 JPEG VGA 98 T02 JPE 99 03 LOADING AND DEFAULT PLAYBACK After inserting the DISC the player searches for and counts the files with appropriate formats currently only JPG MP3 and WMA are supported OSD will show the message Searching for files CD R media and the number of files found will appear
12. 7 or less are allowed to play Adult Allow any title to play factory default BLUETOOTH HANDSFREE OPERATION User guide for bluetooth operation I When user use our Blue tooth HEAD UNIT please make sure the mobile phone you use must does support Blue tooth functions Headset or Handsfree profiles or both 2 Before you start to use our Bluetooth HEAD UNIT please make sure complete pairing with your mobile phone first Please refer to the user manual section PAIRING for detail PAIRING instruction To ensure the best reception for Pairing or Re connection please make sure the Phone Battery is fully charged when making the Pairing or Re connection 3 Please always try pairing the Mobile Phone with Head unit after a few minutes of the Mobile Phone was Switched On to ensure the best pairing result 4 is this unit device model number which is displayed on the mobile phone BT 60 5 To achieve the best performance please always keep the Mobile Phone within 3 meters of the Head unit 6 Please always keep a clear path between the Mobile Phone amp the Head unit 7 Never put any metal object or any obstacle between the path of the Mobile Phone amp the Head unit 8 Some brand of Mobile Phone like Sony Ericsson may have Power Saving Mode selection when Blue Tooth mode is switched on PLEASE DO NOT Switches ON Power saving Mode when operating with this Head Unit as some abnormal communal behavior will happen
13. AV IN OUT MUTE POWER 2 EJECT 3 PANEL RELEASE 4 AUDIO MENU BUTTON CD DVD OK BUTTON 5 MODE 6 ENCODER VOLUME 7 35MM AN IN JACK 8 SUBWOOFER TUNER AF 9 2 ZONE TUNER TA 10 IX BASS TUNER PTY I TUNER PS AS CD SET UP DVD OSD SET UP I2 TUNER MI MEMORY 1 CD PAUSE PLAY DVD PAUSE PLAY 3 TUNER M2 MEMORY 2 CD STOP DVD STOP 4 TUNER M3 MEMORY 3 CD REPEAT OFF REPEAT TRACK REPEAT DISC DVD REPEAT OFF REPEAT CHAPTER REPEAT TITLE 5 TUNER M4 MEMORY 4 CD RANDOM FOLDER DVD SHORT PRESS M4 DVD MENU 16 TUNER M5 MEMORY 5 17 TUNER 6 MEMORY 6 DVD AUDIO 18 DISPLAY MENU 19 TUNER BAND 20 TUNER SEEK UP TUNE UP CD FILE TRACK UP FAST FORWARD DVD NEXT FAST FORWARD 21 TUNER SEEK DOWN TUNE DOWN CD FILE TRACK DOWN FAST BACKWARD DVD BACK FAST BACKWARD SPECIFICATIONS RADIO SECTION GENERAL Power Supply DC II 14 4V FM Polarity Negative Ground Frequency Range 87 5 108 Mhz Speaker impedance 4 ohms Usable Sensitivity Better than 5dB at S N 30 dB Power Output 4 x 75W Stereo Separation 25 dB at IKHz S N Ratio 50 dB DVD CD PLAYER Usable disc DVD R DVD RW CD CD R AM MW CD RW USB SD Frequency Range 522 1620 Khz Sampling frequency Usable Sensitivity Better than 40dB No of quantization bits S N Ratio 40 dB Frequency 20 20 000Hz Number of channels 2 stereo S N Ratio 90dB REMARK Specifications subject to change without notice 2 BER DIS
14. C PLAY PRECAUTIONS WIRING DIAGRAM AUDIO VIDEO CONNECTIONS Use only in a 12 volt DC negative ground electrical system Disconnect the vehicle s negative battery terminal while mounting and connecting the unit When replacing the fuse be sure to use one with an identical amperage rating Using a fuse with a higher amperage rating may cause serious damage to the unit e DO NOT attempt to disassemble the unit Laser beams from the optical pickup are dangerous to the eyes SUB WOOFER OUTPUT BLUE 5 l e Make sure that pins or other objects do not get inside the unit they may cause malfunctions or create safety C sUB WOUT pm SUB hazards such as electrical shock or laser beam exposure Cmm WOOFER f you have parked the car for a long time in hot or cold weather wait until the _ po temperature in the car become normal before operating the unit Keep the volume at a level at which you can hear outside warning sounds horns sirens etc CD NOTES Playing a defective or dusty CD can cause dropouts in sound Hold CDs as illustrated DO NOT touch the unlabeled side DO NOT attach any seal label or data protection sheet to either side of a disc DO NOT expose a CD to direct sunlight or excessive heat Wipe a dirty CD from the center outward with a cleaning cloth Never use solvents such as benzine or alcohol This unit cannot play 3 inch 8cm CDs Q CAMERA VIDEO INP
15. IAL RELIGION PHONEIN FOLK TRAVEL LEISURE DOCUMENT Factory default stored for PTY preset memory MI News M2 Information M3 Pop Music M4 Sports M5 Classics M6 Finance CD OPERATION AUDIO CD OPERATION TFT MONITOR When a Audio CD is inserted into the player and the following picture will appear on the TFT monitor Contonts Ripping rs Repeat Off Mode Normal AUDIO CD OPERATION REMOTE CONTROL To operates CD function through the following keys on the remote control 17 PAUSE PLAY BUTTON 18 STOP 14 15 8 9 FAST FORWARD amp FAST BACKWARD 19 29 NUMERIC BUTTONS 32 REPEAT 10 13 UP DOWN LEFT RIGHT BUTTON 16 7 RANDOM BUTTON l6 17 PAUSE PLAY BUTTON gt MI Press PAUSE to pause playback still mode The sound from the disc is muted during still mode 2 Press PLAY to resume normal playback 18 STOP m Press STOP to stop playback and show the logo screen The player memorizes the location where playback is stopped 2 Press PLAY to resume playback from the location where playback is stopped DVD VCD 1 1 VCD 2 0 and audio CD 3 Pressing STOP twice is resume playback from the beginning of the disc 14 NEXT gt gt I Press NEXT to skip forward to the beginning of the next chapter 15 BACK I Press BACK to skip backward to the beginning of the previous chapter 8 9 FAST FORWARD amp FAST BACKWARD gt gt or 44 Press FAS
16. OPERATION MP3 WMA Operation TFT Monitor When a MP3 WMA disc is inserted into the player and the following picture will appear on the TFT monitor 2 1902 1KHZ SINE 103 17HZ SINE W OGG Files 7064 427 7 SINF T05 997MZ SINE TOS 102307HZ SIN T07 19997HZ SIN Bass Test Repeat lt On Mode Nomal VAR BITRATE 18 The player automatically plays the first track The elapsed time within the track is displayed on the right side of the top line When the track is finished the second track will begin playing and the track number on the top line will be updated Press STOP to stop playback of the current file 17 PAUSE PLAY BUTTON 18 STOP 14 NEXT 15 8 9 FAST FORWARD amp FAST BACKWARD 19 29 NUMERIC BUTTONS 32 REPEAT 10 13 UP DOWN LEFT RIGHT BUTTON l6 OK BUTTON 7 RANDOM BUTTON MP3 WMA OPERATION REMOTE CONTROL To operates CD function through the following keys on the remote control SELECTING A TRACK TO PLAY Use the UP DOWN LEFT RIGHT direction buttons to move to different file numbers 2 Press the RIGHT direction button when the highlighted file is in the column on the far right and up to five more file in the current directory will be displayed 3 Press the LEFT direction button when the highlighted file is in the column to the far left and the previous five file will be displayed 4 Press OK on a file number and that file will begin to play or b
17. P PPI or TRACK DOWN M button for less than one second to advance to the next track on the CD The selected track number will appear on the display Press and Hold TRACK UP PPI or TRACK DOWN 4 button for more than one second to fast forward or fast reverse through the disc CD play starts when the button is released When the last track playback completed the unit will automatically enter into STOP mode User can press play button to start the CD playback again when in the STOP mode 12 PAUSE PLAY BUTTON 1 Pll Press PAUSE to pause playback still mode The sound from the disc is muted during still mode 2 Press PLAY to resume normal playback 13 STOP BUTTON 2 STOP Press STOP to stop playback and show the logo screen The player memorizes the location where playback is stopped 2 Press PLAY to resume playback from the location where playback is stopped DVD VCD 1 VCD 2 0 and audio CD 3 Pressing STOP twice is resume playback from the beginning of the disc I4 REPEAT BUTTON 3 RPT Press REPEAT button less than 3 seconds to repeat play the current song And keep on repeat Playing the current song until the repeat play is disabled To disable current song repeat play press REPEAT button less than 3 seconds 15 RANDOM BUTTON 4 RDM Press RANDOM button less than 3 seconds is random play all songs on the disc To disable all songs random play press RANDOM button less than 3 seconds MP3 WMA
18. ST The contrast level of the TFT display is set at CONTRAST 10 by default User can use the Encoder Vol Knob to adjust the contrast level from 00 to 50 BRIGHT The brightness level of the TFT display is set at BRIGHT 20 by default User can use the Encoder Vol Knob to adjust the brightness level from 00 to 50 COLOR The color level of the TFT display is set at COLOR 30 by default User can use the Encoder Vol Knob to adjust the color level from 00 to 50 ELI BER DATE SET Once in Date Set mode User can use the Encoder Vol Knob to adjust the Date Month Year Short press the AUDIO button to confirm the entry and move to the next entry CLOCK The time of the clock is set to 12 00 by default User can adjust the time by rotate the Encoder Vol knob clockwise to adjust the minute and rotate the Encoder Vol knob anticlockwise to adjust the hour uL If the unit is equipped with the OPTIONAL RDS Function the clock will be automatically updated by the RDS roadcasting provided if the RDS broadcast does include the clock information RDS CT FUNCTION TIME FORM 2H is the default setting User can use the Encoder Vol Knob to choose the Time Format between 12 Hours amp 24 Hours AV JACK The panel AV Jack is default as AV In source User can use the Encoder Vol Knob to select OUT Once OUT is selected the panel AV jack is changed as an AV OUTPUT AV OUT of the Audio Video Signal of this unit s Built i
19. T FORWARD to fast forward through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 2 Press PLAY to resume normal playback 3 Press FAST BACKWARD to fast reverse through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 4 Press PLAY to resume normal playback Ly The fast forward backward speed may differ depending upon the disc 19 29 NUMERIC BUTTONS I When playback CD MP3 WMA use for track number or File number direct access and use when function need numeric Selection or Input like in the Goto function etc 2 Use when playback DVD which need numeric Selection or Input like in the Goto function etc 32 REPEAT Press REPEAT button less than 3 seconds to repeat play the current song And keep on repeat Playing the current song until the repeat play is disabled To disable current song repeat play press REPEAT button less than 3 seconds 10 13UP DOWN LEFT RIGHT BUTTON lt gt Use to move cursor up down left right EIS BER 16 OK BUTTON Use this button to confirm the selection 7 RANDOM BUTTON RANDOM button less than 3 seconds is random play all songs on the disc To disable all file random play press RANDOM button less than 3 seconds AUDIO CD OPERATION CONTROL PANEL The following functions are available operated through the control panel 17 IN OUT OSD SET UP AS FS TRACK SELECT Press the TRACK U
20. UT YELLOW f e NEVER insert a 3 inch CD contained in the adapter or an irregularly shaped CD VIDEON lt 1 e The unit may not be able to eject it resulting in a malfunction BEF RE OPERATION AUDIO INPUT RIGHT RED c4 YER AUDIOINR jm DO NOT raise the volume level too much as this will block outside sounds making GAME CONSOLE driving dangerous AUDIO INPUT LEFT WHITE Stop the car before performing any complicated operation C AUDIONL t CAUTION DO NOT open covers and do not repair by yourself Consult the dealer or an experienced technician for help INSTALLATION PROCEDURES First complete the electrical connections and then check them for correctness ANTI THEFT SYSTEM This unit is equipped with a detachable panel f lock leve Removing this panel makes the radio totally inoperable VIDEO 1 OUTPUT VIDEOOUT REMOVING THE PANEL Switch off the power of the unit 2 Remove the detachable panel REL button 3 Gently press the button of the case and open the cover Place the panel into the case and take it with you when you leave the car VIDEO 2 OUTPUT VIDEO OUT 2 INSTALL DETACHABLE PANEL Fix right part of face plate in the right part of panel slot of the unit 2 Press down the left side of the face plate until it clicks into the panel slot of the unit Insert mounting bracket
21. angle selected and the total available angles to select for example Ly The first press will show the current angle selected Subsequent presses toggle to the next angle 2 The TFT monitor will light its angle icon when angle changes are available 3 Some DVDs allow angle changes only via the disc menu 4 When a disc is replaced the Set Up returns to the default angle DVD OPERATION CONTROL PANEL Once a DVD disc is inserted into the unit the unit will automatically start the playback from the beginning of the disc and then the DVD MENU or ROOT or TITLE in the DVD disc will appear on the TFT monitor and ROOT will be displayed on the TFT of the unit um Under the DVD MENU or ROOT or TITLE is display on the TFT Monitor The buttons of Track up down 20 21 use as LEFT RIGHT direction button Encoder Volume Knob 6 as UP DOWN direction button and Audio 4 as OK button I2 PLAY PAUSE 111 Press PAUSE to pause playback 2 Press PAUSE to single step forward to the next picture in the video DVD and VCD only 3 Press PLAY to resume normal playback 13 STOP 2 STOP Press STOP to stop playback and show the logo screen The player memorizes the location where playback is stopped 2 Press PLAY to resume playback from the location where playback is stopped DVD VCD I I VCD 2 0 and audio CD 3 Pressing STOP twice is resume playback from the beginning of the disc 20 NEXT M Press NEXT to skip f
22. can select to listen to Tuner music for front speakers and rear speaker for DVD movie And if the user has One or more TFT screens installed in the rear seat or inside the Car the Dual A V Zone function allow the users to enjoy TWO different Video sources For example on the front in dash Built In TFT screen can display the video from the Game Console and the other screen in the rear seat can display video from DVD Movie or other A V source The detail operation as follow ON OFF OPERATION Off is the default setting Long press the 2 Zone button on the control panel or remote control to switch between Dual Zone On or Off The 2 2 will appear on the LCD after Dual Zone is selected TO SELECT FRONT REAR AV SOURCES Once ON is selected Short Press the AUDIO button repeatedly to change between the F Zone Front and the R Zone Rear sources f Front Zone F Zone is selected user have 10 seconds to use the Volume UP DOWN button to navigate through different modes Tuner gt DVD gt AV In are available for selection for Front AV Output f Rear Zone R Zone is selected user have 10 seconds to use the Volume UP DOWN button to navigate through different modes Tuner gt DVD gt AV In are available for selection for Rear AV Output f no selection is being made within 5 seconds the unit will resume to the previous mode TO OPERATE FUNCTION OF FRONT REAR SOURCES The Front Panel
23. ce is resume playback from the beginning of the disc 8 amp 9 FAST FORWARD amp FAST BACK FORWARD gt gt or 44 Press FAST FORWARD to fast forward through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 2 Press PLAY to resume normal playback 3 Press FAST BACKWARD to fast reverse through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 4 Press PLAY to resume normal playback Ly The fast forward backward speed may differ depending upon the disc 14 NEXT M Press NEXT to skip forward to the beginning of the next chapter 15 BACK I Press BACK to skip backward to the beginning of the previous chapter 32 REPEAT Press REPEAT button less than 3 seconds to repeat play the current file And keep on repeat playing the current file until the repeat play is disabled To disable current file repeat play press REPEAT button less than 3 seconds 10 13 UP DOWN LEFT RIGHT BUTTON Use these buttons to move cursor up down left right 16 OK Use this button to confirm the selection 19 29 NUMERIC BUTTONS I When playback CD MP3 WMA use for track number or File number direct access and use when function need numeric Selection or Input like in the Goto function etc 2 When playback DVD use when function need numeric Selection or Input like in the Goto function etc 30A DVD MENU Press DVD MENU to invoke the menu screen included on t
24. ck operation function is same as the operation on CD MP3 WMA Pls refer to CD MP3 WMA Operation for more details ELI BER USB OPERATION The unit can support playback WMA JPEG MPEG4 format which are stored on the Memory Stick Max 1000 tracks Please read carefully the below instruction before you start the operation of USB Function Mode change to USB HOST Under any other mode while inserting a USB stick into the USB connector the unit will automatically switch from 2 7 the current mode to USB mode Once the unit reads the USB stick successfully the first audio music file on the USB stick will automatically start playing Press the MODE button repeatedly to change to another mode or switch back to USB mode WARNING Before removing the USB stick from the USB connector Please always remember to switch off the unit s power or switch to other mode then remove out the USB Stick Never try removing the USB Stick while playing music file on the USB stick It may damage the USB Stick and sometimes will cause the unit system to lock up NOTE The unit can support playback Music Player which have USB Interface However due to the fast changing decoder technology and different kind of hardware interface this unit may or may not be compatible to all the Music Player and USB Stick especially those USB Stick Player which require to install a program driver About Music Flash Player with USB Interface usually the u
25. connect with external Audio Video system such like Digital Camera or Game Console You can connect the external A V system through the A V in jack on front panel After connect with external A V system pressing mode to A V In to enjoy this external A V system on this unit Right Audio Ground Video 3 5 V Cable included Ly The unit only supports the 3 5mm A V Jack Pin Assignment shown as the diagram uL The unit supports A V out thrue the A V Jack on front panel For more details of operation please refer to Menu operation AV Jack DISPLAY MENU BUTTON This DISPLAY inter change button can be used to interchange between the 2 types of DISPLAY INTERFACE the Image Display Interface amp Big Font Display interface This is useful when playing a CD or MP3 or WMA or other music disc and if user prefers to see the CD Track no MP3 File number and elapse time with bigger numerical fonts the Big Font Display offers a better read out for the numerical display User can press the DISP button to inter change from Image Display yaa T62 i1KHZ SINE W Mode Mermal Bi mg ER AER E g a 01 17 2 SINE W roti I h g 4 127 nir Ge ce 7 4 LN x S97HZ SINE LS LI Ls p RJ TO 19907HZ SIN Image Display Interface Big Font Display Interface Caution In some countries it
26. ction etc 2 Use when playback DVD which need numeric Selection or Input like in the Goto function etc 32 REPEAT Press REPEAT button less than 3 seconds to repeat play the current file And keep on repeat Playing the current file until the repeat play is disabled To disable current file repeat play press REPEAT button less than 3 seconds 10 13JUP DOWN LEFT RIGHT BUTTON VJ 4 Use to move cursor up down left right 16 OK BUTTON Use this button to confirm the selection 7 RANDOM BUTTON Press RANDOM button less than 3 seconds is random play all files on the disc To disable all file random play press RANDOM button less than 3 seconds MP3 WMA OPERATION CONTROL PANEL The following functions are available operated through the control panel IN OUT OSD SET UP AS FS DISP MENU FILE SELECT Press the TRACK UP 20 or TRACK DOWN 21 button for less than one second to advance to the next file on the CD The selected track number will appear on the display Press and Hold TRACK UP 20 or TRACK DOWN 21 button for more than one second to fast forward or fast reverse through the disc CD play starts when the button is released ur When MP3 WMA is playback the M5 16 use as RIGHT direction button and M6 17 use as LEFT direction This is useful as navigate thru the LEFT page or RIGHT page which the MP3 WMA interface displayed the TFT monitor Ly When the last file playback completed
27. d BEEP TONE is the default setting Rotate the Encoder Vol Knob to select the BEEP TONE Off option PROGRAMMABLE TURN ON VOLUME VOL PGM This option allows the adjustment of the volume level of the radio will automatically assume when turning on VOL 12 is the default setting To program a specific turn on volume level use the Encoder Vol Knob to select VOLUME LEVEL within 5 seconds REAR SPEAKER ON OFF REAR SPK Rear speaker is set to ON by default If OFF is selected the rear speaker s audio output will be TURNED OFF This function is useful while listening with the HEADPHONE and user doesn t need Rear Speakers sounds output through rear speakers Select ON to reactivate the rear speakers sound output Ly When the Rear Speaker is OFF the Audio Function FADER will not be functional INTER AMPLIFIER ON OFF INTER AMP This is a option selection for user to turn the unit s built in Amplifier system on or off OFF is the default setting This option is useful for user if connected to an external Amplifier amp the user does not want audio output of the built in amplifier system DUAL ZONE OPERATION 2 ZONE DUAL A V ZONE MULTI ENTERTAINMENT OPERATION This unit is equipped with the most advanced Dual A V Zone feature This function is useful if the user would like to select different modes of the Audio and Video AV output source for Front and Rear Speakers and TFT Screens For example user
28. d waiting for about min Then re attach the panel to the unit amp retry the Bluetooth operation again Or user can RESET the whole unit by pressing the RESET button behind the panel gt By pressing the RESET button all the stored memory will resume to factory default LIBER Bluetooth hand free panel function key matrix Panel function button Bluetooth hand free function 3 5 AUDIO Answer Incoming call 2 BAND Reject Incoming call 3 MODE Transfer Phone Conversation backward to Mobile Phone Short Press Answer Incoming call Pairing Re Connection etc Note See Menu operation for more details 4 MENU PAIRING Pairing the bluetooth system between user s mobile phone amp the unit Access into MENU PAIRING mode to activates the operation of Pairing gt Pls see MENU Operation for more details of how to access into MENU mode Once the PAIRING is appearing on the LCD Display press the AUDIO button to activate the Pairing mode gt Keep the mobile phone within 2 meter from the unit when making the pairing To terminate the pairing you can press the CLEAR BAND button at any time Select the Blue Tooth set up on the Mobile Phone Please refer to the instruction manual of your mobile phone on how to enter into the blue tooth set up and blue tooth on off and blue tooth pairing BT60 should appear in the pairing list on the mobile phone User need to select and then input the pa
29. e Right buttons to select the setting 3 Use the Up Down buttons to select the setting to be changed 4 Press Ok to cycle through each possible option or display a list of the options When a list of options appears press the Up Down buttons to move among the displayed options 5 Press Ok again to choose the option and change the setting 6 Press Ok after cycling through the options to change the displayed value of the next available opions and change the setting 2 Use the Right buttons to select the setting 3 Use the Up Down buttons to select the setting to be changed The following subsections explain how to change each of the player s Rating settings Parental Control Rating Selection The Rating allows the user to have parental control feature of the player Press the button the below window will J gt If incorrect password is entered the below Incorrect Password window will appear appear on the screen to allow user to enter the password will pop up a window let user set password Enter Password Sot Posswrord In Correct Password Entor Password The factory default password is 8888 Parental control functions only available if the DVD title is encoded in its program Parental control does not work for VCD SVCD CVD or CD audio Set password setting User can set new password in the Set password setting Go to set press Ok to pop up the Enter Password window enter the old password Pre
30. e first press shows the current language selected subsequent presses toggle the next audio language Some DVDs allow audio selection change only via the disc menu When a disc replaced the Set Up returns to the default setting I l OSD AS PS Press AS PS once to display the amount of time played and time remaining to be played on the disc For example the OSD may display 00 07 19 2 Press AS PS a second time to additionally display the disc type current chapter DVD or track VCD SVCD audio CD and total number of chapters or tracks Also displayed for DVD only is the current title total number of titles audio language type of channels subtitle language and angle selection For example the OSD may display TIPS The AS PS in MPEG4 file will display the file name version file size and frame rate I l 2 N o I Il SET UP AS PS While the DVD disc is being played or under stop mode the SET UP AS PS button on the control panel serve the following function J gt Long Press SET UP AS PS button to bring up the System Setup Menu Please refer to the related description in system Set Up for details operation of Set Up After pressing the Set Up button the LCD will display Set Up and keep on blinking User can use the following buttons to adjust the Set Up items shown on the TFT monitor as follow Encoder Volume Knob as Cursor to navigate thru the Set Up Items shown
31. e highlighted entry indicates a title that title will play from Chapter I 36 SUBTITLE Press SUBTITLE during playback to turn on off subtitles and to change the subtitles DVD only The OSD indicates the current setting giving the subtitle track number and the language selected for example CJ 1 10 Eng CJ 2 10 Fre Ly The first press will show the current subtitle setting selected subsequent presses toggle to the next subtitle setting 2 Some DVDs display subtitles automatically and cannot be turned Off even if the subtitle function is set to Off 3 During some scenes the subtitles may not appear immediately 4 Some DVDs allow subtitle selections and turn subtitles on or off only via the disc menu 5 When a disc is replaced the Set Up returns to the default setting 38 DVD AUDIO Press DVD AUDIO during playback to change the audio language when playback a DVD disc The OSD indicates the current setting by giving the audio track number language audio type and number of channels For example 1 3 OC 1 6 Eng 2 3 OO 2 6 Fre The first press shows the current language selected subsequent presses toggle The next audio language 2 Some DVDs allow audio selection change only via the disc menu 3 When a disc replaced the Set Up returns to the default setting 39 ANGLE Press ANGLE while playing a scene recorded with multiple angles to change the angle DVD only The OSD indicates the 1 1 current
32. g subtitle alphabet isn t correct please make sure to select the correct external subtitle language domain The following language domains are available Turkish Albanian Danish Dutch English Finnish French Gaelic German Italian Kurdish Latin Norwegian Portuguese Spanish Swedish and Turkish Albanian Croat Czech Dutch English German Hungarian lrish Polish Romanian Slovak Slovene and Sorbian Cyrillic Bulgarian Belorussian English Macedonian Moldavian Russian Serbian and Ukrainian Western European Albanian Breton Catalan Danish Dutch English Faroese Finnish French Gaelic German Icelandic Irish Italian Norwegian Portuguese Spanish and Swedish Central_European Ly The MPEG4 Subtitle selection appears the SET UP menu gt language gt MPEG4 subtitle ZIBER SYSTEM SET UP MENU The System Menu allows the user to configure the player s behavior to work in harmony with components to which the player is connected Press the SET UP on the remote control or Long press AS PS button on the front panel to invoke the Setup Menu Pressing the System Menu button during the Setup Menu will be displayed and the setup menu will be turned off Setup menu can be opened during playback When the setup Menu is invoked the OSD will display the following buttons 29 The Up Down buttons can be used to select the category of settings which need to be changed The page of set
33. he DVD disc DVD only 2 Press direction buttons to highlight a selected menu entry 3 Press OK or PLAY to select the highlighted entry If the highlighted entry indicates a chapter or title the disc will play from the selected spot 30B PBC PLAY BACK CONTROL FOR VCD DISC ONLY Press DVD MENU to enable disable PBC functionality with VCD 2 0 discs PBC must be enabled for menu navigation 2 Press a number on the number pad to select a track to play VCD 2 0 only 3 Press OK to make the selection 4 Press DVD MENU for the main menu 34 OSD BUTTON Press OSD button once to display the amount of time played and time remaining to be played on the disc For example the OSD may display 00 07 19 2 Press OSD button a second time to additionally display the disc type current chapter DVD or track VCD audio CD and total number of chapters or tracks Also displayed for DVD only is the current title total number of titles audio language type of channels subtitle language and angle selection For example the OSD may display Title Chapter Audio A Subtitle Bitrate 3 Press OSD button a third time to make the OSD disappear uL Press OSD button in MPEG4 file will display the file name version file size and frame rate 35 GOTO BUTTON Using GOTO to Jump to a Specific Time Chapter Track or Title Press GOTO to enable the GOTO Menu The OSD will display the following Search
34. he disc is removed or reloaded CAUTION A Please always use the OPEN button to slide up down the front panel Please never try to slide up or down the front panel manually this will cause serious amp permanent damage to the slide down mechanism and this will void the warranty B Please do not try to detach remove the front panel by pressing the detach button or attach the front panel when the panel is in the slide down position This may cause serious amp permanent damage to the unit amp panel Only attach or detach the front panel when the panel is in the slide up position LIBER 6 CONTROL PANEL FUNCTION 2 6 e 5 19 6X9 2 L d WOH OBO 9 DO 8 D 08 00 OPERATIONS Long Short Long Long Short Press Press Press Press Press Mute Open amp Close Panel Releas e button Audio Menu Memory Paus e P lay Le Repeat Off Repeat Off Memory 3 Re peat Track 5 Repeat Repeat Disc Repeat Title Random Short press M4 s eS Band nd File Track Fast Fast fre ee P ee Pe Seek Tune File Track Fast Fast Down Down Down Backward Backward REMOTE FUNCTIONS QHOOOQO X000 OO OOOO OPERATIONS Short Long Short Long Short Long Short Long Long Press Press Press Press Press Press Press Press Press Mute Power CCT Open amp Close Eject Eject Audio Menu Volume Up
35. ill display If the incoming call has no the LCD will display CALL ANSWER User can press the PHONE AUDIO button or MODE button to answer accept the call Ly The audio output of the present mode will be muted and the ringing tones will be heard if an incoming call is not being answered User can use the volume up down to adjust the volume level To end the conversation press the CLEAR BAND button The unit will switch back to the previous mode automatically and release the mute of the previous mode at the same time Ly An incoming call under stand by mode Ignition on amp Power Off The system will automatically switch on the head unit r gt While there is an Incoming call or under talking mode the Panel Open Eject key is disactivated Rejecting an incoming call User can press CLEAR BAND button to reject the incoming call Lr The audio output of the present mode will be muted and the ringing tones will be heard if an incoming call is not being answered After pressing the CLEAR BAND button the mute of the present mode will be released OUTGOING CALL Use the mobile phone which paired with this unit to making an outgoing call During the talking mode the LCD Display will display TALKING User can use the volume up down to adjust the volume level To end the conversation press the CLEAR BAND button The unit will switch back to the previous mode automatically The mute
36. into the dashboard and bend the mounting REMOVE THE UNIT tabs out with a screwdriver Make Switch of the power of the unit sure that lock lever is flush with Remove the panel and the trim plate the mounting bracket Not 2 Insert both T Keys into hole in front of projecting outward qh the set until they lock 2 Secure the rear of the unit After 3 Pull out the unit fixing mounting bolt and power connector fix the rear of the unit to the car body by rubber cushion 3 Insert trimplate 4 WIRING DIAGRA ISO SMAL FUSE 20 PIN AUDIO POWER HARNESS EN See Figure 1 GREY CHANNEL RED Ignition wire ACC BLACK YELLOW Battery wire B il il d y BLUE WHITE i STRIPE POWER Il ll ll AMPLIFIER n n T REMOTE o Q ORANGE m 2 REVERSE gt OVERRIDE WIRE ISO INE See Figure 2 8 HOLOJNNOO V HOLO3NNOO Figure 2 ISO CONNECTOR 4 PIN 8 PIN FEMALE WITH MALE TERMINAL WHITE BLACK LEFT FRONT SPEAKER GREEN LEFT REAR SPEAKER GREEN BLACK LEFT REAR SPEAKER WHITE LEFT FRONT SPEAKER j r lh Hl O HH 0 1 me a 7 WHITE era 3 CHANNEL Not supplied ANTENNA ANTENNA EXTENDER JACK CABLE Not supplied RCA TO RCA WHITE 7 _ CABLES A Connect to power amplifier n
37. ion in Audio Operation of Sub woofer for details operation of the Subwoofer control LLB The Subwoofer Level and Low Pass Filter control will only appear in the Audio Menu only if the Subwoofer function is currently activated On 8 SUB WOOFER SUB W Long Press the SUB W button to activate the Sub woofer function On and Sub woofer will appear on the LCD display for 3 seconds press the SUB W button again to turn off the Sub woofer function 10 iX BASS BUTTON iX Bass Long Press the iX Bass button to turn on the IX Bass function and iX Bass will appear in the LCD display for 3 seconds Press the iX Bass button again to turn off the IX Bass function gt Please refer to the related description in Audio Operation of iX Bass for details operation of iX Bass control The IX Bass Boost Level control will only appear in the Audio Menu only if the iX Bass function is currently activated On 5 MODE BUTTON MODE Short Press the MODE button to select a different mode of operation as indicated on the display panel Available modes include Tuner DVD Card SD MMC Card USB AV IN I and AV IN 2 6 ENCODER VOLUME BUTTON To increase the volume rotate the volume control knob clockwise To decrease the volume rotate the volume control knob counter clockwise When the volume is adjusted the volume level is shown on the display panel as a number ranging from 00 lowest to 46 highest FRONT PANEL A V IN JACK The unit is allowed to
38. n DVD player uL This AV Out selection is useful for user by simply plug and connect to any external TFT system without any extra installation CAMERA OFF is set as default If user connected a back up camera system to this unit user should choose Camera ON mode Once is selected amp the vehicle is in Reverse Gear Backup mode the front in dash TFT display will automatically switch to Back Up Camera Video signal regardless whatever mode is currently displayed on the front in dash TFT g gt If connected to a back up camera system but this option is selected to OFF mode User still can press the mode button to switch AV In to display the Back Up Camera Video on the front in dash TFT TUNER SET User can use the Encoder Vol Knob to select between Local or Distance mode This feature is used to designate the strength of the signals at which the radio will stop during automatic tuning Distance is the default setting allowing the radio to stop at a broader range of signals To set the unit to select only strong local stations during automatic tuning rotate the Encoder Vol Knob button until Local appears on the display TUNER AREA User can use the Encoder Vol Knob to select the frequency spacing which is most appropriate for the area this unit is used in U S A South America Europe or Oirt Russia Band BEEP TONE The beep tone feature allows the selection of an audible beep tone when a button is presse
39. nit takes longer time to read this kind of player than normal USB Stick Especially if the Flash Player with built in power battery sometimes takes 20 30 seconds to start up the playback This unit is not compatible with any Portable type of Hard disk File Playback Operation All the USB playback operation function is same as the operation on CD MP3 WMA Pls refer to CD MP3 WMA Operation for more details MULTI FORMAT DISC FILTER FUNCTION Subwoofer Test Subwoofer Test If a DISC or USB or MEMORY CARD contains various categories of files This Filter function 2 8 can hide the files and not allow selection during the File Folder searching The selection is done among the 3 categories a Audio b Photo c Video 2 Use right arrow keys to go the Filter field press OK key to open the selection box Use up down keys to navigate through the categories that need to be hidden Then press OK key to confirm Use left key to exit the filter function MPEG4 OPERATION The unit is support playback MPEG4 files the details operation is exactly the same as CD MP3 WMA operation The following are special functions pertaining to the playback of MPEG4 File EXTERNAL SUBTITLE External Subtitle setting is used for choosing the language domain only for MPEG4 After selecting one language domain alphabet when playback a MPEG4 with external subtitle the subtitle display will use this language alphabet If the displayin
40. occasionally if Power Saving Mode is switched on 9 Before user make Outgoing call or Incoming call make sure the mobile phone s Blue Tooth function was switched ON 10 To ensure the best conversation quality performance please always keep talking within meter of the Head Unit Il If user want to Dis connect the Head unit with the Mobile Phone please switch OFF Blue Tooth connectivity on the Mobile Phone or go to the system menu dis connect to disconnect the bluetooth connectivity manually please refer to the user manual section dis connection of the bluetooth system for details instruction 12 Some Mobile Phones can support IN BAND RING such as Nokia In such case the Incoming Ringing Tone will be same as the original Ring tone of the Mobile Phone But some Mobile Phones like Sony Ericsson do not support this feature The Ring tone will be using the standard Ring tone of the Head unit 13 When in telephone mode during talking it is highly recommended to set the volume to below 30 in order to achieve the best sound quality As if the volume is too high it may create unwanted echo inside the car and this unwanted echo may feedback into the microphone 14 If the Bluetooth related operation is not performing normally like cannot make pairing cannot making an outgoing call User can try to make a SOFT RESET of the Bluetooth module by removing detaching the panel from the main unit an
41. of the previous mode will be released at the same time During the talking mode if the Ignition is being turned off the unit will keep the conversation even if the Ignition is Switched off After finished the conversation User can press CLEAR BAND button to switch off the unit Once the is display on the LCD press the AUDIO button to activate the manual Dis Connect mode If the Dis Connection is successful the LCD Display will display And the unit will switch back to the previous mode automatically CALL TRANSFER To audio transfer from head unit back to the mobile phone During the talking mode user can LONG press the TRANSFER MODE button more than 3 seconds to transfer the audio from the unit back to the mobile phone for privacy reason The LCD Display will CALL TRANSFER Ly After the Transfer button is pressed the mute of the present mode will be released at the same time Ly Depending on different type of Mobile Phone the time need for activating the CALL TRANSFER mode is different Like Nokia Mobile Phone usually takes 3 5 seconds after pressed the TRANSFER button for audio transfer back or forth through Unit to mobile phone HIGHLIGHT FEATURES Incoming call ringing volume Preset the Ringing volume level for any incoming call Ly Pls see MENU PHONE VOL for details operation VB ER 37 SPECIFICATION TFT SCREEN SECTION Screen Size 3 5 Measured Diagonally
42. ompact disc is extremely Clean the disc or try to play a new one dirty or defective disc Temperature inside the caris Cool off or until the ambient temperature too high returns to normal Condensation Leave the player to off for an hour or so then try again Volume is in minimum Adjust volume to a desired level Wiring is not properly Check wiring connection connected The built in microcomputer is Press the RESET button not operating properly due to Front panel is not properly fixed into noise its place The installation angle is Adjust the installation angle to less more than 30 degrees than 30 degrees The disc is extremely dirtor Clean the compact disc Then try to play a defective disc new one The antenna cable is not Insert the antenna cable firmly connected The signals are too weak Select a station manually Press the eject button to correct the problem If the error code does not disappear consult your nearest service dealer Mechanism Error Maybe disc dirty disc scratched Replace the disc Idisc upside down 39
43. on the TFT Monitor Track Up Down 20 21 buttons as Cursor Left Right to navigate thru the Set Up items shown on the TFT Monitor AUDIO button as ENTER to confirm the selected item shown on the TFT Monitor ur Short Press Set Up button again or Play button to resume the DVD playback MEMORY CARD OPERATION The unit can support playback WMA JPEG and MPEG4 format which are stored into SD and MMC Memory Card Max 2GB max 1000 tracks Pls read below before you start the operation of Memory Card Inserting and Removing a SD or MMC card on the main unit Detach the Front Panel 4 Detach the Front Panel Insert the Memory Card with Label up side Inserting the SD or MMC card Push in till you hear a click Push in till you hear a click Remove the Memory Card Removing the SD or MMC card MODE CHANGE TO MEMORY CARD After SD or MMC card was inserted into the main unit card slot Press Mode button to select card mode The unit will starts playing the files contained on the Memory Card Once the unit read the Memory Card successfully the first file on the Memory Card will automatically start playback Press Mode button repeatedly is allowing changing to other modes or switch back to card mode If no any Memory Card is inserted into the main unit card slot Press mode button will Automatically skip card mode FILE PLAYBACK OPERATION All the SD or MMC Memory Card playba
44. or all 4 speakers becomes DVD mode AUDIO OPERATION AUDIO MENU Short Press AUDIO button to access the Audio Menu User can navigate thru the Audio Menu items by pressing the AUDIO button repeatedly or by pressing the Tuning Up or Tuning Down Button Once the desired menu item appears on the display adjust that option by using the encoder volume knob within 5 seconds The following menu items can be adjusted as described above The unit will automatically exit the Audio Menu after five seconds of inactivity SUBWOOFER Sub woofer Level User has 5 seconds to use the encoder volume knob to adjust the Sub woofer lever from 00 to The Sub woofer level control is only applicable if the unit is equipped with the optional subwoofer line out and only if the unit is connected to an optional sub woofer speaker The Sub woofer level control option will only appear in the Audio Menu if the Sub woofer function is activated ON by pressing the Sub w button on control panel Sub woofer Low Pass Filter LPF User has 5 seconds to use the encoder volume knob to select the 4 different Low Pass filter Flat 80Hz 120Hz or 60Hz Ly The Sub woofer LPF control is only applicable if the unit is equipped with the optional subwoofer line out and only if the unit is connected to an optional sub woofer speaker J gt The Sub woofer LPF option will only appear in the Audio Menu if the Sub woofer function is activated by pressing the Sub
45. orward to the beginning of the next chapter 21 BACK K Press BACK to skip backward to the beginning of the previous chapter 20 21 FAST FORWARD amp FAST BACK FORWARD gt gt I or 14 Long press FAST FORWARD to fast forward through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 2 Press PLAY to resume normal playback 3 Long press FAST BACKWARD to fast reverse through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 4 Press PLAY to resume normal playback 2 I 4 REPEAT 3 RPT 5 Press REPEAT button less than 3 seconds to repeat play the current file And keep on repeat Playing the current file until the repeat play is disabled To disable current file repeat play press REPEAT button less than 3 seconds 15 DVD MENU 4 RDM Press DVD MENU button less than 3 seconds to invoke the DVD MENU or ROOT on the DVD disc uL Under the DVD MENU or ROOT or TITLE is display on the TFT Monitor The button of Track up down 20 21 use as LEFT RIGHT direction button Encoder Volume Knob 6 as UP DOWN direction button and Audio button 4 as OK button 17 DVD AUDIO 6 Long press DVD AUDIO button during playback to change the audio language DVD only The OSD indicates the current setting by giving the audio track number language audio type and number of channels For example Fa 1 3 DO 1 6 Eng 2 3 DO 2 6 Fre Ly Th
46. ot used Tape bare end of wire Reverse gear signal Connect to Reverse Light Lead Reverse Light L7 Le 10 Pin View Figure 1 20 PIN AUDIO POWER HARNES S 20 PIN HARNESS PIN CHART PIN 1 REAR PRE AMPLIFIER LINE OUT COMMON BATTERY N EI BER PANEL OPEN CLOSE OPERATION This unit is equipped with the most advanced full logic motorized slide down system You can enjoy this advance technology with just a single press of the OPEN button Please read carefully the following operation instruction before operating the unit OPEN CLOSE THE PANEL Press the Open button to slide down open a closed panel or to slide up close an opened panel LOADING A CD When the panel is in the slide down position the disc slot becomes accessible Insert a CD through the disc slot the CD will be automatically loaded and the panel will also close automatically amp playback will begin If no CD is inserted press Open button again to slide up close the panel EJECTING A CD Press Open button to slide down the panel if a CD is loaded it will be ejected automatically No further key press is needed If the ejected CD is not being removed after 10 seconds it will be reloaded automatically And the panel will automatically slide up after disc has been reloaded Warning If the ejected disc remains in the slot the Open button will not function so closing the panel by using Open button is prevented unless t
47. s unlawful to operate a vehicle while video is displayed in the driver s viewing area Please always switch the unit s display to Big Font Type Display mode by pressing the DISP MENU button while driving For safety reason the driver should only enjoy watch the video while the car is in parking mode RESET After releasing the front panel use a pencil or any non metallic object to press amp hold the reset button for five seconds to reset the main unit and the unit will return to the factory default settings TO RESET THE DVD SETTING Press SET UP button on remote control or long press AS PS button to bring up the SET UP Menu select RATING then select DEFAULT the DVD Setting will resume to factory default value MENU OPERATIONS MENU FUNCTION LIST MENU Press amp hold the DISPLAY MENU button for more than 3 seconds to access into the menu User can navigate thru the menu items by pressing the DISPLAY MENU button repeatedly or by pressing the Tuning Up or Tuning Down Buttons to move to the next or previous menu item Once the desired menu item appears on the display user can adjust that option by using the Encoder Vol Knob within 5 seconds The menu items can be adjusted as described below ANGLE The panel viewing angle of the display can be adjusted by rotating the encoder vol knob to select the most appropriate viewing angle This is useful for user to adjust amp obtain the optimum viewing angle inside the vehicle CONTRA
48. ss Ok twice then the Enter New Password window will pop up Enter the new password press Ok to confirm Once entered the correct password press OK the correct password message will appear Enter New Password 3 3 Set Password MISC UNEP METEO Using the Up Down buttons move to the Misc the Misc Rating settings will appear Use Default Settings Press Ok to to cycle through the available options The following options are available 2 Use the Right buttons to select the setting 3 Use the Up Down buttons to select the setting to be changed 4 Press Ok for each setting to cycle through the options and change the settings The following subsections will explain the available options for each of the Misc settings Use Default Settings Press Ok pop up window Use Default Setting there are two selections Yes No No Close Setup menu Yes Return to Use Default Setting Kid Safe Only titles with a parental control setting of are allowed to play G Only titles with a parental control setting of 2 or less are allowed to play PG Only titles with a parental control setting of 3 or less are allowed to play PG 13 Only titles with a parental control setting of 4 or less are allowed to Play PG R Only titles with a parental control setting of 5 or less are allowed to play R Only titles with a parental control setting of 6 or less are allowed to play NC 17 Only titles with a parental control setting of
49. ssword 1234 If the pairing is successful the display will show PAIRING OKE and Mobile Phone Name If the pairing failed PAIRING FAIL will be flashing the Display for 3 seconds And the unit will switch back to the previous mode automatically Ly During the Pairing only Power CLEAR BAND Volume amp Mute are functional other function keys are disabled amp non operational during the pairing mode Re Connection of the bluetooth system The unit is with built in Auto Reconnection function In some conditions user need to reconnect manually For example like the following If The Mobile Phone is out of range 2 meters away from the Head unit Under the condition of lost connection when the user come back to the unit At the same time there is an incoming call or user is under conversation on the Mobile Phone 2 meters away from the Head Unit and come back to Head unit If user wants Audio Transfer back from Mobile Phone to Head unit It needs to re connect manually The unit can be re connected by the following methods Access into MENU RECONNECT mode to activate the manual RE Connection Ly Pls see MENU Operation for more details of how to access into MENU mode Once the RECONNECT is displayed on the LCD press the AUDIO button to activate the manual RE Connect mode J gt Keep the mobile phone within 2 Meter from the unit when making the connection gt 2 manual re connect
50. ting for that category will be displayed instantly once selected the category 2 When the category changes are set press Up Down repeatedly to return to the text buttons Selecting the appropriate button and pressing OK can change settings in a different category LANGUAGE SETTINGS Using the Up Down buttons move to the Language button The player s Language settings will appear 2 Use the Right buttons to select the setting 3 Use the Up Down direction buttons to select the setting to be changed 4 Press Ok to cycle through each possible option or display a list of the available options When a list of options appears press the Up Down buttons to move among the displayed options 5 Press Ok again to choose the option and change the setting 6 Press Ok after cycling through the options to change the displayed value of the next available option and change the setting ZIBER OSD Language Selecting the OSD setting allows the user to select a preferred language for the OSD menu The following subsections explain the available options for each of the Video settings and messages The following options are available TV Aspect Ratio Selecting the TV Aspect setting allows the user to select the aspect ratio of the TV DVD and VCD only The following options are available 4 3 Aspect ratio of TV is 4 3 16 9 Aspect ratio of TV is 16 9 Both widescreen and 4 3 contents will fill the entire screen Nore
51. w button on control panel X BASS User has 5 seconds to use the encoder volume knob to select the 3 different Bass Boost level Low Mid or High BASS BASS LEVEL Level User has 5 seconds to use the encoder volume knob to adjust the desired Bass level range from 6 to 6 BASS CFQ C Frq User has 5 seconds to use the encoder volume knob to adjust the desired Bass Center Frequency to 60Hz 80Hz 00Hz or 200Hz BASS Q BassQ User has 5 seconds to use the encoder volume knob to adjust the desired Bass Quality Factor to 2N IN IW or 2W 13 Figure shows the Bass Quality factor Curve characteristics of each step 15 0 12 5 10 0 7 5 5 0 Level dB dB 2 5 0 0 10 0 100 0 1 0K 10 0K Figure Frequency Hz MIDDLE MIDDLE LEVEL User has 5 seconds to use the encoder volume knob to adjust the desired Middle level range from 6 to 6 MIDDLE CFQ C FRQ User has 5 seconds to use the encoder volume knob to adjust the desired Middle Range Center Frequency to 500Hz IKHz 5KHz or 2 5KHz MIDDLE Q MID Q User has 5 seconds to use the encoder volume knob to adjust the desired Middle Quality Factor to 2N IN IW 2W Figure 2 shows the middle Quality factor Curve characteristics of each step Level dB Figure 2 Frequency Hz TREBLE TREBLE LEVEL User has 5 seconds to use the encoder volume knob to adjust the desired Treble level range from 6 to 6 TREBLE CFQ FREQ
52. y direct numeric input 5 Enter a file number with the numeric buttons 0 9 and 10 button to play the input Files Number 17 PAUSE PLAY BUTTON PII MI Press PAUSE to pause playback still mode The sound from the disc is muted during still mode 2 Press PLAY to resume normal playback I8 STOP nm Press STOP to stop playback and show the logo screen The player memorizes the location where playback is stopped 2 Press PLAY to resume playback from the location where playback is stopped DVD VCD I I VCD 2 0 and audio CD 3 Pressing STOP twice is resume playback from the beginning of the disc ZIBER 14 NEXT M Press NEXT to skip forward to the beginning of the next chapter 15 BACK I 4 Press BACK to skip backward to the beginning of the previous chapter 8 9 FAST FORWARD amp FAST BACKWARD gt gt 44 Press FAST FORWARD to fast forward through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 2 Press PLAY to resume normal playback 3 Press FAST BACKWARD to fast reverse through the disc Each time the button is pressed a new speed 2X 4X 8X or 20X is selected 4 Press PLAY to resume normal playback Ly The fast forward backward speed may differ depending upon the disc 19 29 NUMERIC BUTTONS I When playback CD MP3 WMA used for track number or File number direct access and used when function need numeric Selection or Input like in the Goto fun
Download Pdf Manuals
Related Search