Home

Asrock 939A790GMH motherboard

Contents

1. Auto Select Auto to automatically detect the hard disk drive After selecting the hard disk information into BIOS use a disk 4 utility such as FDISK to partition and format the new IDE hard disk drives This is necessary so that you can write or read data from the hard disk Make sure to set the partition of the Primary IDE hard disk drives to active CD DVD This is used for IDE CD DVD drives ARMD This is used for IDE ARMD ATAPI Removable Media Device such as MO LBA Large Mode Use this item to select the LBA Large mode for a hard disk gt 512 MB under DOS and Windows for Netware and UNIX user select Disabled to disable the LBA Large mode Block Multi Sector Transfer The default value of this item is Auto If this feature is enabled it will enhance hard disk performance by reading or writing more data during each transfer PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing DMA Mode DMA capability allows the improved transfer speed and data integrity for compatible IDE devices S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analysis and Reporting Technology feature Configuration options Disabled Auto Enabled 32Bit Data Transfer Use this item to enable 32 bit access to maximize the IDE hard disk data transfer rate 49 3 4 5 PCIPnP Configuration BIOS SETUP UTILITY ee Advanced PCI PnP Settings Va
2. otherwise it will be hidden The range of the value depends on the CPU you adopt on this motherboard However for system stability it is not recommended to adjust the value of this item Processor Voltage This item will show when Multiplier Voltage Change is set to Manual otherwise it will be hidden The range of the value depends on the CPU you adopt on this motherboard However for safety and system stability it is not recommended to adjust the value of this item HT Bus Speed This feature allows you selecting Hyper Transport bus speed Configura tion options Auto 200 MHz 400 MHz 600 MHz 800 MHz and 1000 MHz HT Bus Width This feature allows you selecting Hyper Transport bus width Configura tion options Auto 8 Bit and 16 Bit CPU Thermal Throttle Use this item to enable CPU internal thermal control mechanism to keep the CPU from overheated Configuration options Disabled Auto 12 5 25 37 5 50 62 5 75 and 87 5 The default value is Auto Memory Configuration Memory Clock This item can be set by the code using Auto You can set one of the standard values as listed 133MHz DDR266 166MHz DDR333 and 200MHz DDR400 40 DRAM Voltage Use this to select DRAM voltage Configuration options Auto 2 60V to 2 95V The default value is Auto Memory Timing BIOS SETUP UTILITY OC Tweaker Memory Timing TRAS Auto TRP Auto TRCD Aut
3. Configuration options PCI Onboard and PCI Express Internal Graphics Mode This allows you to adjust internal graphics mode The default value is UMA Configuration options UMA and Disabled Share Memory This allows you to set share memory feature The default value is Auto Configuration options Auto 32MB 64MB and 128MB 45 Onboard HDMI HD Audio This allows you to enable or disable the onboard HDMI HD Audio in AMD 790GX Surround View This allows you to enable or disable the Surround View feature or Hybrid CrossFireX feature 3 4 3 ACPI Configuration BIOS SETUP UTILITY Advanced ACPI Settings Select auto detect or disable the STR feature Away Mode Support Disabled Restore on AC Power Loss Power Off Ring In Power On Disabled PCI Devices Power On Disabled PS 2 Keyboard Power On Disabled RTC Alarm Power On Disabled Select Screen ACPI HPET Table Disabled Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it Check Ready Bit Use this item to enable or disable the feature Check Ready Bit Away Mode Support Use this item to enable or disable Away Mode support under Windows XP Media Center OS The default value is Disabled
4. Copyright 1985 2005 American Megatrends Inc Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the BIOS SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Dis card changes and exit setup Select OK to exit the BIOS SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop out the following message Dis card changes Select OK to discard all changes Load BIOS Defaults Load BIOS default values for all the setup questions F9 key can be used for this operation Load Performance Setup Default IDE SATA This performance setup default may not be compatible with all system configurations If system boot failure occurs after loading please resume optimal default settings F5 key can be used for this operation Load Performance Setup AHCI Mode This performance setup AHCI mode may not be compatible with all system configurations If system boot failure occurs after loading please resume optimal default settings F3 key can be used for this operation Load Performance Setup RAID Mode This performance setup RAID mode may not be compatible with all system configurations If system boot failure occurs after loading please resume optimal default settings F4 key can be used for this operation Load Power
5. EuP Ready AMD 14 ag Pci SB750 15 Se B Chipset Se 30 EE at 14 SE reg l AIA 29 BS en Aiha sel 2 EEE AEE EEE AEE EEE EEE o CE E ec An ai See Bad E Se E SEH y 28 27 26 25 24 23 22 2120191817 PS2_USB_PW1 Jumper 19 Third SATAII Connector SATAII_3 PORT 2 ATX 12V Power Connector ATX12V1 20 Secondary SATAII Connector CPU Heatsink Retention Module SATAII_2 PORT 1 939 Pin CPU Socket 21 Primary SATAII Connector CPU Fan Connector CPU_FAN1 SATAII_1 PORT 0 2 x 184 pin DDR DIMM Slots 22 Chassis Speaker Header Dual Channel A DDR1 DDR2 Blue SPEAKER 1 White 2 x 184 pin DDR DIMM Slots 23 System Panel Header PANEL1 White Dual Channel B DDR3 DDR4 Black 24 SPI Flash Memory 8Mb ATX Power Connector ATXPWR1 25 Print Port Header LPT1 White Primary IDE Connector IDE1 Blue 26 Floppy Connector FLOPPY1 USB 2 0 Header USB8_9 Blue 27 Serial Port Connector COM1 USB 2 0 Header USB6_7 Blue 28 Internal Audio Connector CD1 Black USB 2 0 Header USB4_5 Blue 29 Front Panel Audio Header Power Fan Connector PWR_FAN1 HD_AUDIO1 White Clear CMOS Jumper CLRCMOS1 30 Infrared Module Header IR1 Southbridge Controller 31 Northbridge Controller Chassis Fan Connector CHA_FAN1 32 PCI Express 2 0 x16 Slot PCIE2 Blue Fifth SATAII Connector SATAII_5 PORT AN 33 PCI Express 2 0 x1 Slot PCIE1 White Fourth SATAII Connector SATAII_4 PORT 3 34 Northbridge Controller 11 1 4 I O Panel 1 USB 2 0 P
6. CLRCMOS1 0o o see p 11 No 14 Default Clear CMOS Note CLRCMOS1 allows you to clear the data in CMOS The data in CMOS includes system setup information such as system password date time and system setup parameters To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action 23 2 8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard Floppy Connector 33 pin FLOPPY1 see p 11 No 26 the red striped side to Pin1 Note Make sure the red striped side of the cable is plugged into Pin1 side of the connector Primary IDE connector Blue 39 pin IDE1 see p 11 No 9 connect the blue end u connect the black end J SE to the IDE devices to the motherboard S 80 conductor ATA 66 100 133 cable Note Please refer to the instruction of your IDE device vendor for the details Serial ATAII Connectors These five Serial ATAI
7. EE 44 3 4 2 Chipset Configuration cccccceeceeeeesseeeeeeeeeeeeeeaeaeeees 45 IAS ACP COMiQurallOn EE 46 3 4 4 Storage Configuration ccccccececeeeeeeeeesseeseeeeeeeeeeeeeaas 48 3 4 5 PCIPNP Configuration s oi aean o a 50 3 4 6 Floppy Configuration cccccceceeeceeeesssseseeeeeeeeeeeaaaenees 51 3 4 7 Super lO Configuration cccccceeeeeeeeseseeeeeeeeeeeeeeaaaees 51 3 4 8 USB Configuration e arenira A EA 53 3 5 Hardware Health Event Monitoring Gcreen 54 36 BOOKSO EE 55 3 6 1 Boot Settings Configuration cccccccssseseeseeeeeeeeeeees 59 Sal Security Stee EE 56 SB EXPOSE EE 57 A Softwa SUDDO BEE 58 4 1 Install Operating System c cc cecccccecsseeeceeseeeeeeeeeesseeeeees 58 4 2 Support CD Information c ccc cccesecceeeeeeeeeeenseeeeeeeeeseeeeeeeens 58 4 2 1 Running Support CD 58 4 2 2 Drivers Menu 58 4 23 UNITES Men EN 58 4 2 4 Contact Information sssceseeeiserresrreerrrrrrerrreerierrrerrnn 58 4 1 Introduction Thank you for purchasing ASRock 939A790GMH motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setu
8. This motherboard supports Hot Plug feature for SATA SATAII HDD in RAID AHCI mode Please read below operation guide of SATA SATAII HDD Hot Plug feature carefully Before you process the SATA SATAII HDD Hot Plug please check below cable accessories from the motherboard gift box pack A 7 pin SATA data cable B SATA power cable with SATA 15 pin power connector interface A SATA data cable Red B SATA power cable SATA 7 pin The SATA 15 pin power 1x4 pin conventional connector connector Black connect power connector White to SATA SATAII HDD connect to power supply Caution d Without SATA 15 pin power connector interface the SATA SATAII Hot Plug cannot be processed Even some SATA SATAII HDDs provide both SATA 15 pin power connector and IDE 1x4 pin conventional power connector interfaces the IDE 1x4 pin conventional power connector interface is definitely not able to support Hot Plug and will cause the HDD damage and data loss Points of attention before you process the Hot Plug 1 Below operation procedure is designed only for our motherboard which supports SATA SATAII HDD Hot Plug The SATA SATAII Hot Plug feature might not be supported by the chipset because of its limitation the SATA SATAII Hot Plug support information of our motherboard is indicated in the product spec on our website www asrock com Make sure your SATA SATAII HDD can support Hot Plug function from your dealer or HDD
9. Windows XP XP 64 bit OS Right click the desktop choose Properties and select the Settings tab so that you can adjust the parameters of the multi monitor according to the steps below A Click the Identify button to display a large number on each monitor B Right click the display icon in the Display Properties dialog that you wish to be your primary monitor and then select Primary When you use multiple monitors with your card one monitor will always be Primary and all additional monitors will be designated as Secondary C Select the display icon identified by the number 2 D Click Extend my Windows desktop onto this monitor E Right click the display icon and select Attached if necessary F Set the Screen Resolution and Color Quality as appropriate for the second monitor Click Apply or OK to apply these new values 19 G Repeat steps C through E for the diaplay icon identified by the number one two three and four For Windows 7 7 64 bit Vista Vista 64 bit OS Right click the desktop choose Personalize and select the Display Settings tab so that you can adjust the parameters of the multi monitor according to the steps below A Click the number 2 icon B Click the items This is my main monitor and Extend the desktop onto this monitor C Click OK to save your change D Repeat steps A through C f
10. and apple devices via Bluetooth or WiFi networks then you can start experiencing the exciting motion controlled games Also please do not forget to pay attention to ASRock official website regularly we will continuously provide you the most up do date supported games ASRock website http Awww asrock com Feature Aiwi index asp 12 13 14 15 If you desire a faster less restricted way of charging your Apple devices such as iPhone iPod iPad Touch ASRock has prepared a wonderful solution for you ASRock APP Charger Simply installing the APP Charger driver it makes your iPhone charged much quickly from your computer and up to 40 faster than before ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode S1 Sus pend to RAM S3 hibernation mode S4 or power off S5 With APP Charger driver installed you can easily enjoy the marvelous charging experience than ever ASRock website http www asrock com Feature AppCharger index asp Although this motherboard offers stepless control it is not recommended to perform over clocking Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU While CPU overheat is detected the system will automatically shutdown Before you resume the system please check if the CPU fan on the motherboard functions properly and unplug th
11. option to select logo in POST screen This option only appears when you enable the option Full Screen Logo Configuration options Auto EUP Scenery and ASRock The default value is Auto Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature Boot Up Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up 3 7 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it BIOS SETUP UTILITY Main OC Tweaker Advanced H W Monitor Boot Security SE Security Settings Install or Change the password Supervisor Password Not Installed User Password Not Installed Change User Password Select Screen Select Item Change General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc 56 3 8 Exit Screen BIOS SETUP UTILITY Main OCTweaker Advanced H WMonitor Boot Security Exit Exit Options 3 Exit system setup after saving the changes Discard Changes and Exit Discard Changes F10 key can be used for this operation Load BIOS Defaults Load Performance Setup Default IDE SATA Load Performance Setup AHCI Mode Load Performance Setup RAID Mode Load Power Saving Setup Default Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C
12. possibility of such damages arising from any defect or error in the manual or product FE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may Cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in California USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents Its Ia dee e en WEE 5 Iech PACKAGES Content ee ee EE 5 Je SS DCCINCAIONS eebe 6 1 3 Motherboard Layout soaennnnnnsennnenenenrenertrreeernnreenrrrrenennnnne 11 Wa aO 2 re lt WEE 12 Nu te Ue Le TN 13 Pre installation Precautions cccccccceeeeeeeeeceeeeeeeeeeeeseeeeeeeeeeeeeeeees 13 ZA e Ae EE ME te EE 14 2 2 Installation of CPU Fan and Heatsink 14 2 3 Installation of Memory Modules DIMM nnnssnonaaannnnnnnnnnnnneean 15 2 4 Expansion Slots PCI and PCI Express Slots ccccce 17 2 5 Dual Monitor and Surround Display Features 0nnnnan000aaaee
13. press any key to start Please insert a floppy diskette into the floppy drive and press any key E The system will start to format the floppy diskette and copy SATA SATAII drivers into the floppy diskette 32 STEP 3 Use RAID Installation Guide to set RAID configuration Before you start to configure RAID function you need to check the RAID installation guide in the Support CD for proper configuration Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD RAID Installation Guide STEP 4 Install Windows XP XP 64 bit OS on your system After step 1 2 3 you can start to install Windows XP XP 64 bit OS on your system At the beginning of Windows setup press F6 to install a third party RAID driver When prompted insert the SATA SATAII driver diskette containing the AMD RAID driver After reading the floppy disk the driver will be presented Select the driver to install according to the OS you install Select AMD AHCI Compatible RAID Controller x86 platform for Windows XP or AMD AHCI Compatible RAID Controller x64 plat form for Windows XP 64 bit NOTE If you install Windows XP XP 64 bit on IDE HDDs and want to manage create convert delete or rebuild RAID functions on SATA SATAII HDDs you still need to set up SATA Operation Mode to RAID first Then please set the RAID configuration by using the Windows RAID installation guid
14. user manual The SATA SATAII HDD which cannot support Hot Plug function will be damaged under the Hot Plug operation Please make sure the SATA SATAII driver is installed into system properly The latest SATA SATAII driver is available on our support website www asrock com Make sure to use the SATA power cable amp data cable which are from our motherboard package Please follow below instructions step by step to reduce the risk of HDD crash or data loss 30 How to Hot Plug a SATA SATAII HDD Points of attention before you process the Hot Plug Please do follow below instruction sequence to process the Hot Plug improper procedure will cause the SATA SATAII HDD damage and data loss Sil Please connect SATA power cable 1x4 pinend BG Connect SATA data cable to F SCK Connect SATA 15 pin power cable connector Sed Connect SATA data cable to Black end to SATA SATAII HDD the SATA SATAII HDD How to Hot Unplug a SATA SATAII HDD Points of attention before you process the Hot Unplug Please do follow below instruction sequence to process the Hot Unplug improper procedure will cause the SATA SATAII HDD damage and data loss Unplug SATA data cable from SATA SATAII HDD side 31 White to the power supply 1x4 pin cable the motherboard s SATAII connector 2 13 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive firs
15. you can easily enjoy the benefits of dual monitor feature without installing any add on VGA card to this motherboard This motherboard also provides independent display controllers for DVI D D Sub or HDMI to support dual VGA output so that DVI D D sub or HDMI can drive same or different display contents To enable dual monitor feature please follow the below steps 1 Connect DVI D monitor cable to VGA DVI D port on the I O panel connect D Sub monitor cable to VGA D Sub port on the I O panel or connect HDMI monitor cable to HDMI port on the I O panel VGA D Sub port VGA DVI D port HDMI port choose the combination for dual monitor output support DVI D D Sub or HDMI D Sub DVI D and HDMI monitors cannot display at the same time You can only 2 If you have installed onboard VGA driver from our support CD to your system already you can freely enjoy the benefits of multi monitor function after your system boots If you haven t installed onboard VGA driver yet please install onboard VGA driver from our support CD to your system and restart your computer Then you can start to use multi monitor function on this motherboard HD DVD disc the content will be displayed only in one of the three When you playback HDCP protected video from Blu ray BD or monitors instead of all monitors 18 Surround Display Feature This motherboard supports surround display upgrade With the internal VGA output support DVI D D Sub and
16. 1 x COM port header 1 x Print port header CPU Chassis Power FAN connector 24 pin ATX power connector 4 pin 12V power connector CD in header Front panel audio connector 3 x USB 2 0 headers support 6 USB 2 0 ports BIOS Feature 8Mb AMI BIOS AMI Legal BIOS Supports Plug and Play ACPI 1 1 Compliance Wake Up Events SMBIOS 2 3 1 Support VCCM NB Voltage Multi adjustment Support CD Drivers Utilities AntiVirus Software Trial Version ASRock Software Suite CyberLink DVD Suite OEM and Trial Creative Sound Blaster X Fi MB Trial Unique Feature ASRock OC Tuner see CAUTION 7 Intelligent Energy Saver see CAUTION 8 Instant Boot ASRock Instant Flash see CAUTION 9 ASRock OC DNA see CAUTION 10 ASRock AIWI see CAUTION 11 ASRock APP Charger see CAUTION 12 Hybrid Booster CPU Frequency Stepless Control see CAUTION 13 ASRock U COP see CAUTION 14 Boot Failure Guard B F G Hardware CPU Temperature Sensing Monitor Chassis Temperature Sensing CPU Chassis Power Fan Tachometer CPU Quiet Fan Voltage Monitoring 12V 5V 3 3V Vcore Microsoft Windows 7 7 64 bit Vista Vista 64 bit XP XP Media Center XP 64 bit compliant Certifications FCC CE WHQL ErP EuP Ready ErP EuP ready power supply is required see CAUTION 15 For detailed product information please visit our website http www asrock com WARNING Please realize tha
17. 8 7 256MD2 S Currently RADEON HD2400XT series graphics cards are only supported with AMD Phenom CPU Please visit our website for the future driver update and the latest information Enjoy the benefit of ATI Hybrid CrossFirex Step 1 Install one compatible PCI Express graphics card to PCIE2 slot blue For the proper installation procedures please refer to section Expansion Slots Step 2 Connect the monitor cable to the correspondent connector on the PCI Express graphics card on PCIE2 slot Step 3 Boot your system Press lt F2 gt to enter BIOS setup Enter Advanced screen and enter Chipset Settings Then set the option Surround View to Enabled Step 4 Boot into OS Please remove the ATI driver if you have any VGA driver installed in your system Step 5 Install the onboard VGA driver from our support CD to your system for both the onboard VGA and the discrete graphics card Step 6 Restart your computer Then you will find ATI Catalyst Control Center on your Windows taskbar iB Car aes ATI Catalyst Control Center 21 Step 7 Double click ATI Catalyst Control Center Click View click CrossFire and then select the option Enable CrossFire ey CrossFire Enable CrossFire anpa el fm men kir fu Eyii peer isa regir a ppa ms cm he m or ba ee ey ee Ti oe D r ha nepar om ae age g ee E Ke Step 8 Click Yes to con
18. 985 2003 American Megatrends Inc OnBoard Floppy Controller Use this item to enable or disable floppy drive controller Serial Port Address Use this item to set the address for the onboard serial port or disable it Configuration options Disabled 3F8 IRQ4 2F8 IRQ3 DES IRQ4 2E8 IRQ3 Infrared Port Address Use this item to set the address for the onboard infrared port or disable it Configuration options Disabled 2F8 IRQ3 and 2E8 IRQ3 51 Parallel Port Address Use this item to set the address for the onboard parallel port or disable it Configuration options Disabled 378 and 278 Parallel Port Mode Use this item to set the operation mode of the parallel port The default value is ECP EPP If this option is set to ECP EPP it will show the EPP version in the following item EPP Version Configuration options Normal Bi Directional and ECP EPP EPP Version Use this item to set the EPP version Configuration options 1 9 and 1 7 ECP Mode DMA Channel Use this item to set the ECP mode DMA channel Configuration options DMAO DMA1 and DMA3 Parallel Port IRQ Use this item to set the IRQ for the parallel port Configuration options IRQ5 and IRQ7 PS 2 Port Type Use this item to set the PS 2 port type 52 3 4 8 USB Configuration ILONEN Ow OS an OM BG Advanced USB Configuration To enable or disable lt the onboard USB controllers USB 2 0 Support Ena
19. DCP in their equipment it is highly recommended that the HDTV or LCD monitor you purchase is compatible 20 2 6 ATIM Hybrid CrossFireX Operation Guide This motherboard supports ATI Hybrid CrossFireX feature ATI Hybrid CrossFireX brings multi GPU performance capabilities by enabling an AMD 790GxX integrated graphics processor and a discrete graphics processor to operate simultaneously with combined output to a single display for blisteringly fast frame rates Currently ATI Hybrid CrossFireX Technology is only supported with Windows Vista 7 OS and is not available with Windows XP OS In the future ATI Hybrid CrossFireX may be supported with Windows XP OS Please visit our website for updated information 4 What does an ATI Hybrid CrossFireX system include An ATI Hybrid CrossFireX system includes an ATI Radeon 2400 or ATI Radeon 3450 series graphics processor and a motherboard based on an AMD 790GX integrated chipset all operating in a Windows Vista 7 environment Please refer to below PCI Express graphics card support list for ATI Hybrid CrossFireX For the future update of more compatible PCI Express graphics cards please visit our website for further information Vendor Chipset Model Driyer ATI RADEON X2400PRO MSI RX2400 PRO TD256EH Catalyst 8 7 RADEON HD2400XT POWERCOLOR HD2400 XT Catalyst 8 7 256MB DDR3 RADEON HD3450 POWERCOLOR AX3450 Catalyst
20. GPU Clock This option only appears when you enable Onboard GPU Clock Override The default value is 700 mGPU Voltage Use this to select mGPU voltage Configuration options Auto 1 10V to 1 45V The default value is Auto Would you like to save current setting user defaults In this option you are allowed to load and save three user defaults according to your own requirements 42 3 4 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Chipset Configuration ACPI Configuration Storage Configuration PCIPnP Configuration Floppy Configuration SuperlO Configuration and USB Configuration BIOS SETUP UTILITY AJETE OLOM Reet com Advanced W TAAA LTC OR CTT TT OTT LA EE DD S Advanced Settings Options for CPU WARNING Setting wrong values in below sections may cause system to malfunction gt Chipset Configuration gt ACPI Configuration gt Storage Configuration gt PCIPnP Configuration gt Floppy Configuration Select Screen gt SuperIO Configuration Select Item gt USB Configuration Go to Sub Screen General Help BIOS Update Utility Load Defaults ASRock Instant Flash Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc A Setting wrong values in this section may cause o the system to malfunction ASRock Instant Flash ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM This convenient BIOS upd
21. HDMI and external add on PCI Express VGA card you can easily enjoy the benefits of surround display feature Please refer to the following steps to set up a surround display environment 1 Install the ATI PCI Express VGA cards on PCIE2 slot Please refer to page 17 for proper expansion card installation procedures for details 2 Connect DVI D monitor cable to VGA DVI D port on the I O panel connect D Sub monitor cable to VGA D Sub port on the I O panel or connect HDMI monitor cable to HDMI port on the I O panel Then connect other monitor cables to the corresponding connectors of the add on PCI Express VGA cards on PCIE2 slot DVI D and HDMI monitors cannot display at the same time You can only choose the combination DVI D D Sub or HDMI D Sub 3 Boot your system Press lt F2 gt to enter BIOS setup Enter Share Memory option to adjust the memory capability to 32MB 64MB 128MB 256MB or 512MB to enable the function of VGA D sub Please make sure that the value you select is less than the total capability of the system memory If you do not adjust the BIOS setup the default value of Share Memory Auto will disable VGA D Sub function when the add on VGA card is inserted to this motherboard 4 Install the onboard VGA driver and the add on PCI Express VGA card driver to your system If you have installed the drivers already there is no need to install them again 5 Set up a multi monitor display For
22. Hour Minute Second Use this item to specify the system time Single Channel Memory Mode 256MB 166MHz DDR333 None None None Boot Security Exit Use Enter TAB or SHIFT TAB to select a field Use or to configure system Time Select Screen Select Item Change Field Select Field General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc System Date Day Month Date Year Use this item to specify the system date 38 3 3 OC Tweaker Screen In the OC Tweaker screen you can set up overclocking features BIOS SETUP UTILITY WET OC Tweaker CAEI WEIWERT Security Exit CPU Configuration Overclocking may cause damage to your CPU and motherboard It should be done at your own risk and expense CPU Frequency MHz 200 PCIE Frequency MHz 100 Spread Spectrum Auto Processor Maximum Multiplier x12 2400 MHZ Processor Maximum Voltage 1 400 V Multiplier Voltage Change Auto HT Bus Speed Auto gt Select Screen HT Bus Width Auto Wi Select Item CPU Thermal Throttle Auto Enter Go to Sub Screen F1 General Help Memory Configuration F9 Load Defaults ee eee F10 Save and Exit Memory Clock Auto ESC Exit DRAM Voltage Auto v02 54 C Copyright 1985 2005 American Megatrends Inc CPU Configuration Overclock Mode Use this to select Overclock Mode The default value is Auto Configura tion options Auto CPU PCIE S
23. I SATAII SATAII_1 PORT 0 lt T gt g connectors support SATAII see p 11 No 21 S i S i S or SATA hard disk for internal A A A A A SATAII_2 PORT 1 a z storage devices The current see p 11 No 20 SZ Wy del z fool lhg SATAII interface allows up to SATAII_3 PORT 2 2 d a d d 3 0 Gb s data transfer rate see p 11 No 19 SATAII_4 PORT 3 see p 11 No 18 SATAII_5 PORT 4 see p 11 No 17 Serial ATA SATA Either end of the SATA data cable Data Cable can be connected to the SATA Optional SATAII hard disk or the SATAII connector on this motherboard 24 USB 2 0 Headers 9 pin USB8_9 see p 11 No 10 9 pin USB6_7 see p 11 No 11 9 pin USB4_5 see p 11 No 12 Print Port Header 25 pin LPT1 AFD see p 11 No 25 Infrared Module Header 5 pin IR1 see p 11 No 30 Internal Audio Connectors 4 pin CD1 CD1 see p 11 No 28 Front Panel Audio Header 9 pin HD_AUDIO1 see p 11 No 29 USB_PWR P 9 P 9 GND DUMMY P 6 USB_PWR USB_PWR 25 Besides four default USB 2 0 ports on the I O panel there are three USB 2 0 headers on this motherboard Each USB 2 0 header can support two USB 2 0 ports This is an interface for print port cable that allows convenient connection of printer devices This header supports an optional wireless transmitting and receiving infrared modul
24. IMISRock 939A 790GMH User Manual Version 1 0 Published July 2010 Copyright 2009 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of the
25. Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode 46 PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Disabled Please set this option to Enabled if you plan to use this motherboard to submit Windows Vista certification 47 3 4 4 Storage Configuration BIOS SETUP ON Advanced Configure onboard Storage Configuration serial ATA a controller SATA Operation Mode IDE gt IDE1 Master Hard Disk gt IDE1 Slave Not Detected gt SATAII 1 Not Detected gt SATAII 2 Not Detected gt SATAII 3 Not Detected gt SATAII 4 Not Detected gt SATAII 5 Not Detected Select Screen gt eSATAIL 1 Not Detected Select Item Change Option General Help Load Defaults Save and Exit Ex
26. SATA SATAII device used please set up SATA Operation Mode to IDE in BIOS 2 15 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit OS on your SATA SATAII HDDs without RAID functions please follow below procedures according to the OS you install 2 15 1 Installing Windows XP XP 64 bit Without RAID Functions If you want to install Windows XP XP 64 bit on your SATA SATAII HDDs without RAID functions please follow below steps Using SATA SATAII HDDs with NCQ and Hot Plug functions AHCI mode STEP 1 Set Up BIOS A Enter BIOS SETUP UTILITY gt Advanced screen Storage Configuration B Set the SATA Operation Mode option to AHCI STEP 4 Install Windows XP XP 64 bit OS on your system You can start to install Windows XP XP 64 bit OS on your system At the beginning of Windows setup press F6 to install a third party AHCI driver When prompted insert the SATA SATAII driver diskette containing the AMD AHCI driver After reading the floppy disk the driver will be presented Select the driver to install according to the OS you install Select AMD AHCI Compatible RAID Controller x86 platform for Windows XP or AMD AHCI Compatible RAID Controller x64 platform for Windows XP 64 bit 34 Using SATA SATAII HDDs without NCQ and Hot Plu
27. Saving Setup Default Load power saving setup default F6 key can be used for this operation 57 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 7 7 64 bit Vista Vista 64 bit XP XP Media Center XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to display the menus 4 2 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects the installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to Know more about ASRock welcome to vis
28. ate tool allows you to update system BIOS without entering operating systems first like MS DOS or Windows Just launch this tool and save the new BIOS file to your USB flash drive floppy disk or hard drive then you can update your BIOS only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute ASRock Instant Flash utility the utility will show the BIOS files and their respective information Select the proper BIOS file to update your BIOS and reboot your system after BIOS update process completes 43 3 4 1 CPU Configuration BIOS SETUP UTILITY Advanced CPU Configuration Enable or disable the feature of Boot Failure Guard Cool n Quiet Auto Memory Hole Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Boot Failure Guard Enable or disable the feature of Boot Failure Guard Cool n Quiet Use this item to enable or disable AMD s Cool n Quiet technology The default value is Auto Configuration options Auto Enabled and Disabled If you install Windows 7 Vista and want to enable this function please set this item to Enabled Please note that enabling this function may reduce CPU voltage and memory frequency and lead to syste
29. aunch this tool and save the new BIOS file to your USB flash drive floppy disk or hard drive then you can update your BIOS only in a few clicks without prepar ing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system The software name itself OC DNA literally tells you what it is capable of OC DNA an exclusive utility developed by ASRock provides a conve nient way for the user to record the OC settings and share with others It helps you to save your overclocking record under the operating system and simplifies the complicated recording process of overclocking settings With OC DNA you can save your OC settings as a profile and share with your friends Your friends then can load the OC profile to their own system to get the same OC settings as yours Please be noticed that the OC profile can only be shared and worked on the same motherboard To experience intuitive motion controlled games is no longer only available at Wii ASRock AIWI utility introduces a new way of PC gaming operation ASRock AIWI is the world s first utility to turn your iPhone iPod touch as a game joystick to control your PC games All you have to do is just to install the ASRock AIWI utility either from ASRock official website or ASRock software support CD to your motherboard and also download the free AIWI Lite from App store to your iPhone iPod touch Connecting your PC
30. bled Legacy USB Support Enabled USB Keyboard Remote Power On Disabled USB Mouse Power On Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc USB Controller Use this item to enable or disable the use of USB controller USB 2 0 Support Use this item to enable or disable the USB 2 0 support Legacy USB Support Use this option to select legacy support for USB devices There are four configuration options Enabled Auto Disabled and BIOS Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and BIOS setup when Disabled is selected If you have USB compatibility issue it is recommended to select Disabled to enter OS BIOS Setup Only USB devices are allowed to use only under BIOS setup and Windows Linux OS USB Keyboard Remote Power On Use this item to enable or disable USB Keyboard Remote Power On on the system USB Mouse Power On Use this item to enable or disable USB Mouse Power On on the system 53 3 5 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperat
31. cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 16 2 4 Expansion Slots PCI and PCI Express Slots There are 2 PCI slots and 2 PCI Express slots on this motherboard PCI slots PCI slots are used to install expansion cards that have the 32 bit PCI interface PCIE slots PCIE1 PCIE x1 slot White is used for PCI Express cards with x1 lane width cards such as Gigabit LAN card SATA2 card etc PCIE2 PCIE x16 slot Blue is used for PCI Express cards with x16 lane width graphics cards Installing an expansion card Step 1 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 3 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 4 Fasten the card to the chassis with screws 17 2 5 Dual Monitor and Surround Display Features Dual Monitor Feature This motherboard supports dual monitor feature With the internal VGA output support DVI D D Sub and HDMI
32. e This connector allows you to receive stereo audio input from sound sources such as a CD ROM DVD ROM TV tuner card or MPEG card This is an interface for the front panel audio cable that allows convenient connection and control of audio devices 1 High Definition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instruction in our manual and chassis manual to install your system 2 If you use AC 97 audio panel please install it to the front panel audio header as below A Connect Mic_IN MIC to MIC2 L B Connect Audio_R RIN to OUT2_R and Audio_L LIN to OUT2_L C Connect Ground GND to Ground GND D MIC_RET and OUT_RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E Enter BIOS Setup Utility Enter Advanced Settings and then select Chipset Configuration Set the Front Panel Control option from Auto to Enabled F Enter Windows system Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager For Windows XP XP 64 bit OS Click Audio I O select Connector Settings K choose Disable front panel jack detection and save the change by clicking OK For Windows 7 7 64 bit Vista Vista 64 bit OS Click the right top Folder icon ve choose Disable front panel jack detection and save the change by clicking OK G To ac
33. e in the following path in the Support CD RAID Installation Guide 2 14 2 Installing Windows 7 7 64 bit Vista Vista 64 bit With RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit on a RAID disk composed of 2 or more SATA SATAII HDDs with RAID functions please follow below steps STEP 1 Set up BIOS A Enter BIOS SETUP UTILITY gt Advanced screen Storage Configuration B Set the SATA Operation Mode option to RAID STEP 2 Use RAID Installation Guide to set RAID configuration Before you start to configure RAID function you need to check the RAID installation guide in the Support CD for proper configuration Please refer to the BIOS RAID installation guide part of the document in the following path in the Support CD RAID Installation Guide STEP 3 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system 33 NOTE1 If you install Windows 7 7 64 bit Vista Vista 64 bit on IDE HDDs and want to manage create convert delete or rebuild RAID functions on SATA SATAII HDDs you still need to set up SATA Operation Mode to RAID in BIOS first Then please set the RAID configuration by using the Windows RAID installation guide in the following path in the Support CD RAID Installation Guide NOTE2 Currently if you install Windows 7 7 64 bit Vista Vista 64 bit on IDE HDDs and there are no
34. e power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system EuP stands for Energy Using Product was a provision regulated by European Union to define the power consumption for the completed system According to EuP the total AC power of the completed system shall be under 1 00W in off mode condition To meet EuP standard an EuP ready motherboard and an EuP ready power supply are required According to Intel s suggestion the EuP ready power supply must meet the standard of 5v standby power efficiency is higher than 50 under 100 mA current consumption For EuP ready power supply selection we recommend you checking with the power supply manu facturer for more details 10 1 3 Motherboard Layout OO OO P WN 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 21 8cm 8 6 in nt A EE Hybrid CrossFire K r O O lt ATX12V1 8 e gt amp 3 2 3 2 z z 5 3112113 3 Z S OClellellelle S 3 SRIBIBIE z R 8 ell S i alz z 2 Z Sialla e E z lellalleo ls Ss mall 2 O Spy Eig Gun cue s 939A790GMH 9 lH EE AMD af 790GX 34 e Chipset 10 33 SE NEE EE 32 ASRock E PCIE2 13 ue PCI Express 2 0
35. g functions IDE mode STEP 1 Set up BIOS A Enter BIOS SETUP UTILITY Advanced screen Storage Configuration B Set the SATA Operation Mode option to IDE STEP 2 Install Windows XP XP 64 bit OS on your system 2 15 2 Installing Windows 7 7 64 bit Vista Vista 64 bit Without RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit on your SATA SATAII HDDs without RAID functions please follow below steps Using SATA SATAII HDDs with NCQ and Hot Plug functions AHCI mode STEP 1 Set Up BIOS A Enter BIOS SETUP UTILITY gt Advanced screen Storage Configuration B Set the SATA Operation Mode option to AHCI STEP 2 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system Using SATA SATAII HDDs without NCQ and Hot Plug functions IDE mode STEP 1 Set up BIOS A Enter BIOS SETUP UTILITY gt Advanced screen Storage Configuration B Set the SATA Operation Mode option to IDE STEP 2 Install Windows 7 7 64 bit Vista Vista 64 bit OS on your system 35 2 16 Untied Overclocking Technology This motherboard supports Untied Overclocking Technology which means during overclocking FSB enjoys better margin due to fixed PCI PCIE buses Before you enable Untied Overclocking function please enter Overclock Mode option of BIOS setup to set the selection from Auto to CPU PCIE Async T
36. hannel configuration and please install identical DDR DIMMs in all four slots You may refer to the Dual Channel Memory Configuration Table below Dual Channel Memory Configurations DDR DDR3 DDR4 Blue Slot Blue D Black GES Black a BE Populated Populated aan aeons we Populated Er E EE Populated Populated Populated For the configuration 3 please install identical DDR DIMMs in all four slots 1 Ifyou want to install two memory modules for optimal compatibility and reliability it is recommended to install them in the slots of the same color In other words install them either in the set of blue slots DDR1 and DDR2 or in the set of black slots DDR3 and DDR4 2 If only one memory module or three memory modules are installed in the DDR DIMM slots on this motherboard it is unable to activate the Dual Channel Memory Technology A Ifa pair of memory modules is NOT installed in the same Dual Channel for example installing a pair of memory modules in DDR1 and DDR3 it is unable to activate the Dual Channel Memory Tech nology 15 Installing a DIMM N Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot lt notch lt break C The DIMM only fits in one correct orientation It will
37. herefore CPU FSB is untied during overclocking but PCI PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment 4 Please refer to the warning on page 8 for the possible overclocking risk before you apply Untied Overclocking Technology 36 3 BIOS SETUP UTILITY 3 1 Introduction This section explains how to use the BIOS SETUP UTILITY to configure your system The SPI Memory on the motherboard stores the BIOS SETUP UTILITY You may run the BIOS SETUP UTILITY when you start up the computer Please press lt F2 gt or lt Del gt during the Power On Self Test POST to enter the BIOS SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the BIOS SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on BIOS setup screens and descriptions are for reference purpose only 4 Because the BIOS software is constantly being updated the following and they may not exactly match what you see on your screen 3 1 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information OC Tweaker To set up overclocking features Advanced To set up the advanced BIOS features H W Monitor To display current hardware status Boot To set up the defau
38. it v02 54 C Copyright 1985 2003 American Megatrends Inc Onboard SATA Controller Use this item to enable or disable the Onboard SATA Controller feature SATA Operation Mode Use this item to adjust SATA Operation Mode The default value of this option is IDE If you want to operate RAID function on SATA SATAII HDDs please select RAID Configuration options AHCI RAID and IDE IDE Device Configuration You may set the IDE configuration for the device that you specify We will use the IDE1 Master as the example in the following instruction which can be applied to the configurations of IDE1 Slave as well 139 CO re OM MOD an OM Ni A UAY Advanced IDE Master Select the type of device connected Device Hard Disk to the system Vendor MAXTOR 6L080J4 Size 80 0 GB LBA Mode Supported Block Mode _ 16Sectors PIO Mode A Async DMA MultiWord DMA 2 Ultra DMA Ultra DMA 6 SMART Supported Select Screen LBA Large Mode de Select Item Block Multi Sector Transfer uto o PIO Mode Auto Change Option DMA Mode Auto General Help S M A R T Disabled Load Defaults 32Bit Data Transfer Disabled Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 48 TYPE Use this item to configure the type of the IDE device that you specify Configuration options Not Installed Auto CD DVD and ARMD Not Installed Select Not Installed to disable the use of IDE device
39. it ASRock s website at http www asrock com or you may contact your dealer for further information 58
40. lt system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use lt lt gt key or lt gt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen 37 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s gt try lt Enter gt lt F1 gt lt F9 gt lt F10 gt lt ESC gt Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the BIOS SETUP UTILITY the Main screen will appear and display the system overview Main 139 CO re OM MOS an OM NA UAY OC Tweaker Advanced H W Monitor System Overview 00 09 System Date Fri 07 23 2010 BIOS Version 939A790GMH P1 00 Processor Type Dual Core AMD Opteron tm Processor 180 64bit Processor Speed 2400MHz Microcode Update 20F32 4D L1 Cache Size 256KB L2 Cache Size 2048KB Total Memory 256MB with 128MB shared memory DDR1 DDR2 DDR3 DDR4 System Time
41. lue in units of PCI Ee clocks for PCI device latency timer PCI IDE BusMaster Enabled register Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc A Setting wrong values in this section may cause o the system to malfunction PCI Latency Timer The default value is 32 It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings PCI IDE BusMaster Use this item to enable or disable the PCI IDE BusMaster feature 50 3 4 6 Floppy Configuration In this section you may configure the type of your floppy drive 139 COX OM u D an OM WO i AG Advanced Floppy Configuration Select the type of _ floppy drive connected to the system Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 4 7 Super IO Configuration BIOS SETUP UTILITY Advanced Configure Super IO Chipset Allow BIOS to Enable bg or Disable Floppy Controller Serial Port Address DES IRQ4 Infrared Port Address Disabled Parallel Port Address 378 Parallel Port Mode ECP EPP EPP Version 1 9 ECP Mode DMA Channel DMA3 Parallel Port IRQ IRQ7 PS 2 Port Type Auto Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1
42. m stability or compatibility issue with some memory modules or power supplies Please set this item to Disable if above issue occurs Memory Hole Use this to enable or disable memory hole The default value is Disabled 44 3 4 2 Chipset Configuration 139 CO ee OM OS an OM Be Advanced Chipset Settings Auto Enable Disable Onboard HD Audio Front Panel Auto CD In Enabled OnBoard Lan Enabled Primary Graphics Adapter PCI Internal Graphics Mode UMA Share Memory Auto Onboard HDMI HD Audio Disabled Select Screen Surround View Disabled Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Onboard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio feature If you select Auto the onboard HD Audio will be disabled when PCI Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel CD Iin Use this item to enable or disable CD In of OnBoard HD Audio If you plan to use this motherboard to submit Windows 7 Vista logo test please disable this option OnBoard Lan This allows you to enable or disable the onboard Lan feature Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card It allows you to select the type of Primary VGA in case of multiple video controllers The default value of this feature is PCI
43. mory Max capacity of system memory 4GB see CAUTION 3 Expansion Slot 1 x PCI Express 2 0 x16 slot blue vip mode 1x PCI Express 2 0 x1 slot 2 x PCI slots Supports Hybrid CrossFirex 7 1 CH HD Audio Realtek ALC888 Audio Codec PCIE x1 Gigabit LAN 10 100 1000 Mb s Realtek RTL8111DL Supports Wake On LAN Rear Panel UO I O Panel 1 x PS 2 Keyboard Port 1 x VGA D Sub Port 1 x VGA DVI D Port 1 x HDMI Port Integrated AMD Radeon HD 3300 graphics DX10 class iGPU Pixel Shader 4 0 Max shared memory 512MB see CAUTION 4 Three VGA Output options D Sub DVI D and HDMI Supports HDMI Technology with max resolution up to 1920x1200 1080P Supports Dual link DVI with max resolution up to 2560x1600 75Hz Supports D Sub with max resolution up to 2048x1536 85Hz Supports HDCP function with DVI and HDMI ports Supports Full HD 1080p Blu ray BD HD DVD playback with DVI and HDMI ports Auie Ts 1 x Optical SPDIF Out Port 4 x Ready to Use USB 2 0 Ports 1 x eSATAII Port 1 x RJ 45 LAN Port with LED ACT LINK LED and SPEED LED HD Audio Jack Rear Speaker Central Bass Line in Front Speaker Microphone see CAUTION 5 Connector 5 x Serial ATAII 3 0Gb s connectors support RAID RAID 0 RAID 1 RAID 5 RAID 10 and JBOD NCQ AHCI and Hot Plug functions see CAUTION 6 1 x ATA133 IDE connector Supports 2 x IDE devices 1 x Floppy connector 1x IR header
44. n 18 2 6 ATI Hybrid CrossFirex Operation Guide 000nnnnee0000000ane 21 ZA MAP CIS SOU EE 23 2 8 Onboard Headers and Connectors ssssseeeesssnnrrrerrresseee n 24 2 9 SATAII Hard Disk Setup Guide cc ceeeecceceeeeeeeeeeaeeeeees 28 2 10 Serial ATA SATA Serial ATAII SATAII Hard Disks fa Ge UE e EE 29 2 11 Hot Plug and Hot Swap Functions for SATA SATAII HDDs 29 2 12 SATA SATAII HDD Hot Plug Feature and Operation Guide 30 2 13 Driver Installation Guide sara hanina 32 2 14 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit With RAID FUNCTIONS ccccceceeseeeeeeeeeeeeeeeeaaaeeees 32 2 14 1 Installing Windows XP XP 64 bit With RAID UII re E ER 2 14 2 Installing Windows 7 7 64 bit Vista Vista 64 bit With RAID Functions ccccccceeeeeeees 33 2 15 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Without RAID FUNCTIONS 34 2 15 1 Installing Windows XP XP 64 bit Without RAID EIERE ats Rtas Se ONAL teeta ease eee Ae 34 2 15 2 Installing Windows 7 7 64 bit Vista Vista 64 bit Without RAID Functions nnnnnnnnnenennn 35 2 16 Untied Overclocking Technology 36 SS Le SETUP UNITY GE 37 oT ut ge e Dee RE 37 8121 BIOS MENU Bar eege Eed 37 3 1 2 Navigation EE 38 32 MEET see ee dere ae 38 3 3 OC TWeaker Scree Miia aa a a AE 39 34 Advanced SG EEM EE 43 SA L CPU CONNU AUO
45. nect it to Pin 1 3 ATX Power Connector CR 24 pin ATXPWR1 see p 11 No 8 1 CH 4 Though this motherboard provides 24 pin ATX power connector it can still work if you adopt a traditional 20 pin ATX power supply To use the 20 pin ATX power supply please plug your power supply along with Pin 1 and Pin 20 Pin ATX Power Supply Installation ATX 12V Power Connector 13 13 OOO 4 pin ATX12V1 see p 11 No 2 Serial port Header RRXD1 9 pin COM1 see p 11 No 27 TTXD 1 DDCD 1 27 Pin 1 3 Connected aa 3 Pin Fan Installation 4 Please connect an ATX power supply to this connector 120 Please connect an ATX 12V power supply to this connector This COM1 header supports a serial port module 2 9 SATAII Hard Disk Setup Guide Before installing SATAII hard disk to your computer please carefully read below SATAII hard disk setup guide Some default setting of SATAII hard disks may not be at SATAII mode which operate with the best performance In order to enable SATAII function please follow the below instruction with different vendors to correctly adjust your SATAII hard disk to SATAII mode in advance otherwise your SATAII hard disk may fail to run at SATAII mode Western Digital A 8 6 4 2 If pin 5 and pin 6 are shorted SATA 1 5Gb s will be enabled On the other hand if you want to enable SATAII 3 0Gb
46. nector STEP 4 Connect the other end of the SATA data cable to the SATA SATAII hard disk g If you plan to use RAID 0 or RAID 1 function you need to install at least 2 SATA SATAII hard disks If you plan to use RAID 5 function you need to install at least 3 SATA SATAII hard disks If you plan to use RAID 10 function you need to install at least 4 SATA SATAII hard disks 2 11 Hot Plug and Hot Swap Functions for SATA SATAII HDDs This motherboard supports Hot Plug and Hot Swap functions for SATA SATAII Devices in RAID AHCI mode AMD SB750 south bridge chipset provides hardware support for Advanced Host controller Interface AHCI a new programming interface for SATA host controllers developed thru a joint industry effort AHCI also provides usability enhancements such as Hot Plug 4 NOTE What is Hot Plug Function If the SATA SATAII HDDs are NOT set for RAID configuration it is called Hot Plug for the action to insert and remove the SATA SATAII HDDs while the system is still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA SATAII HDD What is Hot Swap Function If SATA SATAII HDDs are built as RAID 1 or RAID 5 then it is called Hot Swap for the action to insert and remove the SATA SATAII HDDs while the system is still power on and in working condition 29 2 12 SATA SATAII HDD Hot Plug Feature and Operation Guide
47. o TRRD Auto TRC Auto MA Timing Auto Burst Length 4 Beats Bank Interleaving Auto Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc CAS Latency Use this item to adjust the means of memory accessing Configuration options Auto 2T 2 5T and 3T The default value is Auto TRAS Use this to adjust TRAS values Configuration options Auto 5T to 15T The default value is Auto TRP Use this to adjust TRP values Configuration options Auto 2T to 6T The default value is Auto TRCD Use this to adjust TRCD values Configuration options Auto 2T to 6T The default value is Auto TRRD Use this to adjust TRRD values Configuration options Auto 2T to 4T The default value is Auto TRC Use this to adjust TRC values Configuration options Auto 7T to 22T The default value is Auto MA Timing Use this to adjust values for MA timing Configuration options Auto 2T 1T The default value is Auto Burst Length Burst length can be set to 8 4 or 2 beats 64 Bit Dq must use the 4 beats 41 Bank Interleaving Interleaving allows memory accesses to be spread out over banks on the same node or accross nodes decreasing access contention Chipset Settings Onboard GPU Clock Override This allows you to enable or disable the Onboard GPU Clock Override feature Onboard
48. or the display icon identified by the number three and four 6 Use Surround Display Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use The placement of display icons determines how you move items from one monitor to another lt HDCP Function HDCP function is supported on this motherboard To use HDCP function with this motherboard you need to adopt the monitor that supports HDCP function as well Therefore you can enjoy the superior display quality with high definition HDCP encryption contents Please refer to below instruction for more details about HDCP function What is HDCP HDCP stands for High Bandwidth Digital Content Protection a specification developed by Intel for protecting digital entertainment content that uses the DVI interface HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source or transmitter such as a computer DVD player or set top box and the digital display or receiver such as a monitor television or projector In other words HDCP specification is designed to protect the integrity of content as it is being transmitted Products compatible with the HDCP scheme such as DVD players satellite and cable HDTV set top boxes as well as few entertain ment PCs requires a secure connection to a compliant display Due to the increase in manufacturers employing H
49. orts USB23 8 Microphone Pink 2 VGA D Sub Port 9 Optical SPDIF Out Port 3 LAN RJ 45 Port 10 USB 2 0 Ports USB01 4 Central Bass Orange 11 eSATAIl Port 5 Rear Speaker Black 12 HDMI Port 6 Line In Light Blue 13 VGA DVI D Port 7 Front Speaker Lime 14 PS 2 Keyboard Port Purple There are two LED next to the LAN port Please refer to the table below for the LAN port LED indications LAN Port LED Indications Activity Link LED SPEED LED Description Description No Link Off 10Mbps connection Blinking Data Activity 100Mbps connection 1Gbps connection ACT LINK SPEED LED LED LAN Port If you use 2 channel speaker please connect the speaker s plug into Front Speaker Jack See the table below for connection details in accordance with the type of speaker you use TABLE for Audio Output Connection To support AC3 audio format with HDMI Audio under Vista please install the XP HDMI audio driver The driver is located under the path Drivers NB Audio REALTEK XP64_XP R1 68 And note for LPCM support up to stereo 2 channels only 12 2 Installation 939A 790GMH is a Micro ATX form factor 9 6 in x 8 6 in 24 4 cm x 21 8 cm motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard se
50. p Guide on page 28 to adjust your SATAII hard disk drive to SATAII mode You can also connect SATA hard disk to SATAII connector directly 7 Itis a user friendly ASRock overclocking tool which allows you to surveil your system by hardware monitor function and overclock your hardware devices to get the best system performance under Windows environment Please visit our website for the operation procedures of ASRock OC Tuner ASRock website http Awww asrock com 10 11 Featuring an advanced proprietary hardware and software design Intelligent Energy Saver is a revolutionary technology that delivers unparalleled power savings The voltage regulator can reduce the number of output phases to improve efficiency when the CPU cores are idle In other words it is able to provide exceptional power saving and improve power efficiency without sacrificing computing performance To use Intelligent Energy Saver function please enable Cool n Quiet option in the BIOS setup in advance Please visit our website for the operation procedures of Intelligent Energy Saver ASRock website http www asrock com ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM This convenient BIOS update tool allows you to update system BIOS without entering operating systems first like MS DOS or Windows With this utility you can press lt F6 gt key during the POST or press lt F2 gt key to BIOS setup menu to access ASRock Instant Flash Just l
51. p and information of the Support CD Because the motherboard specifications and the BIOS software might be 4 updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on ASRock website without further notice You may find the latest VGA cards and CPU support lists on ASRock website as well ASRock website http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock 939A790GMH Motherboard Micro ATX Form Factor 9 6 in x 8 6 in 24 4 cm x 21 8 cm ASRock 939A790GMH Quick Installation Guide ASRock 939A790GMH Support CD 1 x Ultra ATA 66 100 133 IDE Ribbon Cable 80 conductor 2 x Serial ATA SATA Data Cables Optional 1 x I O Panel Shield 1 2 Specifications Micro ATX Form Factor 9 6 in x 8 6 in 24 4 cm x 21 8 cm Solid Capacitor for CPU power CPU Socket 939 for AMD Athlon 64FX 64X2 64 processors Supports AMD s Cool n Quiet Technology FSB 1000 MHz 2 0 GT s Supports Untied Overclocking Technology see CAUTION 1 Supports Hyper Transport Technology Chipset Northbridge AMD 790GX Southbridge AMD SB750 Memory Dual Channel DDR Memory Technology see CAUTION 2 4 x DDR DIMM slots Support DDR 400 333 266 non ECC un buffered me
52. play the available devices on your system for you to config ure the boot settings and the boot priority BIOS SETUP UTILITY Main OC Tweaker Advanced H W Monitor Boot Boot Settings Configure Settings during System Boot 1st Boot Device Ist Floppy Device 2nd Boot Device HDD PM HDS722580VL 3rd Boot Device CD DVD 3S CD ROM C 4th Boot Device USB gt Hard Disk Drives gt Removable Drives gt CD DVD Drives ces Select Screen Hl Select Item Enter Go to Sub Screen Fl General Help F9 Load Defaults F10 Save and Exit ESC Exit v02 54 C Copyright 1985 2005 American Megatrends Inc 3 6 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Settings Configuration Disabled Displays normal POST messages Enabled Displays OEM AddOn ROM Display Enabled Logo instead of POST Boot Logo Auto messages Boot From Onboard LAN Disabled Bootup Num Lock On Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Full Screen Logo Use this item to enable or disable OEM Logo The default value is Enabled AddOn ROM Display Use this option to adjust AddOn ROM Display If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the system boots please select Enabled Configuration options Enabled and Disabled The default value is Enabled 55 Boot Logo Use this
53. re the CPU The lever clicks on the side tab to indicate that it is locked STEP 1 STEP 2 STEP 3 STEP 4 Lift Up The Socket Lever Match The CPU Golden Triangle Push Down And Lock To The Socket Corner Small The Socket Lever Triangle 2 2 Installation of CPU Fan and Heatsink After you install the CPU into this motherboard it is necessary to install a larger heatsink and cooling fan to dissipate heat You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation Make sure that the CPU and the heatsink are securely fas tened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU_FAN1 see Page 11 No 5 For proper installation please kindly refer to the instruction manuals of the CPU fan and the heatsink 14 2 3 Installation of Memory Modules DIMM 939A790GMH motherboard provides four 184 pin DDR Double Data Rate DIMM slots and supports Dual Channel Memory Technology For dual channel configuration you always need to install identical the same brand speed size and chip type DDR DIMM pair in the slots of the same color In other words you have to install identical DDR DIMM pair in Dual Channel A DDR1 and DDR2 Blue slots see p 11 No 6 or identical DDR DIMM pair in Dual Channel B DDR3 and DDR4 Black slots see p 11 No 7 so that Dual Channel Memory Technology can be activated This motherboard also allows you to install four DDR DIMMs for dual c
54. s please remove the jumpers from pin 5 and pin 6 SAMSUNG 7 5 3 Ion a 8 6 4 2 If pin 3 and pin 4 are shorted SATA 1 5Gb s will be enabled On the other hand if you want to enable SATAII 3 0Gb s please remove the jumpers from pin 3 and pin 4 HITACHI Please use the Feature Tool a DOS bootable tool for changing various ATA features Please visit HITACHI s website for details http www hitachigst com hdd support download htm 4 The above examples are just for your reference For different SATAII hard disk products of different vendors the jumper pin setting methods may not be the same Please visit the vendors website for the updates 28 2 10 Serial ATA SATA Serial ATAII SATAII Hard Disks Installation This motherboard adopts AMD SB750 south bridge chipset that supports Serial ATA SATA Serial ATAII SATAII hard disks and RAID RAID 0 RAID 1 RAID 5 RAID 10 and JBOD functions You may install SATA SATAII hard disks on this motherboard for internal storage devices This section will guide you to install the SATA SATAII hard disks STEP 1 Install the SATA SATAII hard disks into the drive bays of your chassis STEP 2 Connect the SATA power cable to the SATA SATAII hard disk STEP 3 Connect one end of the SATA data cable to the motherboard s SATAII con
55. t Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from up to bottom side to install those required drivers Therefore the drivers you install can work properly 2 14 Installing Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit With RAID Functions If you want to install Windows 7 7 64 bit Vista Vista 64 bit XP XP 64 bit on a RAID disk composed of 2 or more SATA SATAII HDDs with RAID functions please follow below procedures according to the OS you install 2 14 1 Installing Windows XP XP 64 bit With RAID Functions If you want to install Windows XP XP 64 bit on a RAID disk composed of 2 or more SATA SATAII HDDs with RAID functions please follow below steps STEP 1 Set up BIOS A Enter BIOS SETUP UTILITY Advanced screen Storage Configuration B Set the SATA Operation Mode option to RAID STEP 2 Make a SATA SATAII Driver Diskette A Insert the ASRock Support CD into your optical drive to boot your system B During POST at the beginning of system boot up press lt F11 gt key and then a window for boot devices selection appears Please select CD ROM as the boot device C When you see the message on the screen Generate Serial ATA driver diskette YN press lt Y gt D Then you will see these messages Please insert a blank formatted diskette into floppy drive A
56. t there is a certain risk involved with overclocking including adjusting the setting in the BIOS applying Untied Overclocking Technology or using the third party overclocking tools Overclocking may affect your system stability or even cause damage to the components and devices of your system It should be done at your own risk and expense We are not responsible for possible damage caused by overclocking CAUTION 1 This motherboard supports Untied Overclocking Technology Please read Un tied Overclocking Technology on page 36 for details 2 This motherboard supports Dual Channel Memory Technology Before you implement Dual Channel Memory Technology make sure to read the installation guide of memory modules on page 15 for proper installation 3 Due to the operating system limitation the actual memory size may be less than 4GB for the reservation for system usage under Windows 7 Vista XP For Windows OS with 64 bit CPU there is no such limitation 4 The maximum shared memory size is defined by the chipset vendor and is subject to change Please check AMD website for the latest information 5 For microphone input this motherboard supports both stereo and mono modes For audio output this motherboard supports 2 channel 4 channel 6 channel and 8 channel modes Please check the table on page 12 for proper connection 6 Before installing SATAII hard disk to SATAII connector please read the SATAII Hard Disk Setu
57. tinue FE ne eee me E E kel e E rarei ee oe bee eed ee ei ede meet fe ee ee rd ee ee E Se gn Step 9 Click OK to save your change LAT Been s ALY et Tes mn ee ee ee DR E Tey Pe eer G se ey Cee Poca ee f a ka n Ip Eu te ES E agers greng EI GC D egen ti rs eee Ber re ee Fe LA e REI PEPR phJ ga Zare BR t mg be rd ne r b s ie mra rime rege P Step 10 Reboot your system Then you can freely enjoy the benefit of Hybrid CrossFireX feature Hybrid CrossFirex appearing here is a registered trademark of ATI Technologies Inc and is used only for identification or explanation and to the owners benefit without intent to infringe For further information of ATI Hybrid CrossFirex technology please check AMD website for up dates and details 22 2 7 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap is placed on pins the jumper is Open The illustration d shows a 3 pin jumper whose pin1 and pin2 are Short when jumper cap is placed on ga aga ak these 2 pins shorn Open Jumper Setting PS2 _USB_PW1 1_2 23 Short pin2 pin3 to enable see p 11 No 1 GR Hi 5VSB standby for PS 2 or USB wake up events Note To select 5VSB it requires 2 Amp and higher standby current provided by power supply Clear CMOS Jumper 1 3 23
58. tivate the front mic For Windows XP XP 64 bit OS Please select Front Mic as default record device If you want to hear your voice through front mic please deselect Mute icon in Front Mic of Playback portion For Windows 7 7 64 bit Vista Vista 64 bit OS Go to the Front Mic Tab in the Realtek Control panel Click Set Default Device to make the Front Mic as the default record device System Panel Header lag ko This header accommodates PWRBIN 9 pin PANEL1 GND several system front panel see p 11 No 23 functions DUMMY RESET GND HDLED HDLED Chassis Speaker Header l Please connect the chassis 4 pin SPEAKER 1 TR speaker to this header DUMMY see p 11 No 22 EN 26 Chassis and Power Fan Connectors 3 pin CHA_FAN1 Peay CHA FAN SPEED see p 11 No 16 SE PWR_FAN_SPEED 3 pin PWR_FAN1 a see p 11 No 13 GND CPU Fan Connector y P EPU au sp 4 pin CPU_FAN1 GND FAN_SPEED_CONTROL see p 11 No 5 1234 ED Please connect the fan cables to the fan connectors and match the black wire to the ground pin Please connect the CPU fan cable to this connector and match the black wire to the ground pin 4 Though this motherboard provides 4 Pin CPU fan Quiet Fan support the 3 Pin CPU fan still can work successfully even without the fan speed control function If you plan to connect the 3 Pin CPU fan to the CPU fan connector on this motherboard please con
59. ttings Before you install or remove any component ensure that the power is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded anti static pad or in the bag that comes with the component 5 When placing screws into the screw holes to secure the motherboard to the chassis please do not over tighten the screws Doing so may damage the motherboard 13 2 1 CPU Installation Step 1 Unlock the socket by lifting the lever up to a 90 angle Step 2 Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle Step 3 Carefully insert the CPU into the socket until it fits in place 4 The CPU fits only in one correct orientation DO NOT force the CPU into the socket to avoid bending of the pins Step 4 When the CPU is in place press it firmly on the socket while you push down the socket lever to secu
60. ure motherboard temperature CPU fan speed chassis fan speed and the critical voltage BIOS SETUP UTILITY WET OLOM Ar OGR CEA HW Monitor Boot Security Exit S Enable Disable Hardware Health Event Monitoring CPU Quiet Fan Function CPU Temperature 37C 98 F M B Temperature 27C 80F CPU Fan Speed 4722 RPM Chassis Fan Speed N A Power Fan Speed N A Vcore 1 216V 3 30V 3 248V Select Screen 5 00V 5 136V Select Item 12 00V 12 091V General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc CPU Quiet Fan This item allows you to identify the temperature of CPU fan If you set this option as Disabled the CPU fan will operate in full speed If you set this option as Enabled you will find the items Target CPU Temperature and Target Fan Speed appear to allow you adjusting them The default value is Disabled You are allowed to enable this function only when you install 4 pin CPU fan Target CPU Temperature The target temperature will be between 45 C 113 F and 65 C 149 F The default value is 50 C 122 FL Target Fan Speed Use this option to set the target fan speed You can freely adjust the target fan speed according to the target CPU temperature that you choose Configuration options Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 and Level 9 54 3 6 Boot Screen In this section it will dis
61. ync CPU PCIE Async and Optimized CPU Frequency MHz Use this option to adjust CPU frequency PCIE Frequency MHz Use this option to adjust PCIE frequency Spread Spectrum This item should always be Auto for better system stability Processor Maximum Multiplier It will display Processor Maximum Multiplier for reference Processor Maximum Voltage It will display Processor Maximum Voltage for reference Multiplier Voltage Change This item is set to Auto by default If it is set to Manual you may adjust the value of Processor Multiplier and Processor Voltage However it is recom mended to keep the default value for system stability 39 BIOS SETUP UTILITY WO OC Tweaker SPALITI mm PAM Cyc a LIL Security Exit CPU Configuration Overclocking may cause damage to your CPU and motherboard CEU Uae iiz EA It should be done at PCIE Frequency MHz 100 Auto your own risk and Spread Spectrum ee Processor Maximum Multiplier x12 2400 MHZ 1 400 V Processor Maximum Voltage Multiplier Voltage Change Manual Processor Multiplier x12 2400 MHz Processor Voltage 1 350 V Select Screen Select Item HT Bus Speed Auto Go to Sub Screen HT Bus Width Auto General Help CPU Thermal Throttle Auto Load Defaults Save and Exit Memory Configuration Exit v02 54 C Copyright 1985 2005 American Megatrends Inc Processor Multiplier This item will show when Multiplier Voltage Change is set to Manual

Download Pdf Manuals

Related Search

Related Contents

User Manual demo iPetrol web  miniSwap-U3 Manual  Manual  USER`S MANUAL - Young Tech Co.,Ltd (YTC)  688 User Guide - Sound Devices, LLC  Jsound – JS1 Owners Manual Solar Wireless Speaker  Olympus CAMEDIA C-180 Basic manual  T'nB CHNB19V120 mobile device charger  Electrolux ERT1501FOW2 combi-fridge  

Copyright © All rights reserved. Failed to retrieve file