Philips Wake-up Light HF3490/60
Contents
1. Beep Fig 18 African jungle Fig 19 Wind chimes Fig 20 Using your iPod iPhone as alarm sound Place your iPod or iPhone in the iPod iPhone station Select a wake up song or album playlist on your iPod iPhone D This song starts playing ENGLISH 13 Set your iPod iPhone to pause position or switch it off BD When you have selected your iPod iPhone as alarm sound the paused song starts playing at the set alarm time Note If the iPod iPhone is unable to play the selected song you hear the bird alarm sound of the Wake up Light at the set alarm time Snoozing Gently push down the control lever to the bottom position when the alarm goes off Fig 21 D The light continues to be on at the selected intensity level but the alarm sound stops After 9 minutes the wake up sound is automatically played again Note The 9 minute snooze time is fixed This time cannot be adjusted Note If you push down the control lever with too much force it may jump back to off position Alarm demonstration If you want to get a quick demonstration 60 seconds of the gradually increasing light level and sound level activate the test function of the appliance Push the control lever down to the bottom position for a few seconds until TEST appears on the display Fig 22 Push the control lever down again to stop the demonstration Note The appliance continues to run the alarm demonstration until you push down the control lever ag2. Base iPod iPhone docking station Release slide Preparing for use Installing the appliance Note You can also use the Wake up Light without the base You only have to install the base when you want to use the Wake up Light in combination with your iPod iPhone Hold the Wake up Light above the base Note Make sure that the iPod iPhone station is on the left side of the Wake up Light Align the holes in the bottom of the Wake up Light with the pins on the base Then push the Wake up Light onto the pins click Fig 5 To remove the base remove iPod iPhone turn the Wake up Light upside down and push the release slide on the bottom of the base in the direction of the arrow Then pull the base off the Wake up Light Fig 6 Place the Wake up Light 16 20in 40 50cm from your head for example on a bedside table Fig 7 Put the plug in the wall outlet The hour indication on the display starts flashing to indicate that you have to set the clock time Fig 8 Setting the clock time You cannot use the Wake up Light until you have set the clock time ENGLISH 11 When the hour indication on the display flashes move the middle dial up or down to select the hour Press the middle dial gently and release it to confirm gt The minute indication starts flashing Fig 9 Move the middle dial up or down to select the minutes Press the middle dial gently and release it to confirm gt The appliance leaves the men
3. This warranty does not cover damage resulting from accident misuse or abuse lack of reasonable care or the affixing of any attachment not provided with the product DAMAGES Apple Inc standards All Rights Reserved n order to obtain warranty service simply call toll free 1 866 832 4361 n US Manufactured for Philips Consumer Lifestyle A Division of Philips Electronics North America Corporation 1600 Summe n Canada Imported for Ph iPod is a trademark of App Apple is not responsible fo PHILIPS is a Registered Trademark of Koninklijke Philips Electronics N V 2009 Philips Electronics O RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL r Street 5th Floor Stamford CT 06905 5125 ips Electronics LTD 281 Hillmount Road Markham Ontario L6C 253 e Inc registered in the U S and other countries iPhone is a trademark of r the operation of this device or its compliance with safety and regulatory orth America Corporation Troubleshooting This chapter summarizes the most common problems you could encounter with the appliance If you are unable to solve the problem with the information below call 1 866 832 4361 for assistance Problem Solution The appliance does not work at all The appliance functions properly but the lamp does not work anymore The appliance becomes hot during use The appliance does not respond when try to press or m
4. assistance Close supervision is necessary when this appliance is used by or near children or invalids Children should be supervised to ensure that they do not play with the appliance This appliance is for indoor use only Fig 3 Caution Do not drop the appliance or expose it to heavy shocks Place the appliance on a stable level and non slippery surface Do not use the appliance at room temperatures lower than 50 F 10 C or higher than 95 F 35 C Make sure the vents in the top and in the bottom of the appliance remain open during use ever use the appliance if the lamp housing or top cover is damaged broken or missing To prevent possible damage to the cord do not wrap the cord around the appliance Consult your doctor before you start using the appliance if you have suffered from or are suffering from serious depression Do not use this appliance as a means to reduce your hours of sleep The purpose of this appliance is to help you wake up more easily lt does not diminish your need for sleep The appliance has no on off switch To disconnect the appliance from the power source remove the plug from the wall outlet Use this appliance for its intended household use as described in this manual Do not use attachments not recommended by Philips Electronics North America Corporation SAVE THESE INSTRUCTIONS General This appliance allows you to choose the light intensity level you want to wake up to see section Using the lam
5. not press the dial too hard If you do the dial does not work Move the middle dial up or down to select a function Fig 11 Press the middle dial gently and release it to enter this function Move the middle dial up or down to select an option in this function Press the middle dial gently and release it to confirm If you do not operate the dial for 5 seconds when you are in the menu the appliance automatically leaves the menu and displays the clock time again 12 ENGLISH Setting the alarm To set the alarm you choose an alarm time and the type of sound you want to wake up to The alarm is set when the alarm symbol and the alarm sound symbol are visible on the display Note You can set the light intensity by moving the top dial up or down and you can set the alarm volume by moving the bottom dial up or down If you do not want to wake up to the lamp or to a sound select a light intensity or volume level of O shown on the display as OFF See sections Using the lamp and Radio volume in this chapter Tip When you use the appliance for the first time set the light intensity to 20 The moment you wake up check which light intensity level the appliance has reached by slightly moving the top dial up or down When you do this the current alarm light intensity level appears on the display Set the alarm light intensity to this level for the next day Push the control lever down to the middle position to switch on the a
6. the iPod symbol flashes for 3 seconds BD After 3 seconds the word iPod and the iPod symbol disappear from the display Note If you have selected your iPod iPhone as the alarm sound the iPod symbol stays on the display To play music from your iPod iPhone you can operate the iPod iPhone as you normally would If you do not know how to use your iPod iPhone follow the instructions in the user manual supplied with your iPod iPhone D The music on your iPod iPhone comes out of the speaker of the Wake up Light BD Your iPod iPhone is charged automatically when it is in the iPod iPhone station Note To set the music on your iPod iPhone as alarm sound follow the instructions in section Setting the alarm sound in this chapter Note The iPod iPhone volume setting does not have an effect on the volume setting of the Wake up Light speaker To set the volume move the bottom dial of the Wake up Light up or down to select the volume level you prefer Note When you have connected your iPhone to the Wake up Light and a call comes in the music or the radio goes out and the default ringtone of the iPhone comes out of the speaker of the Wake up Light ENGLISH 15 Dusk simulation function Select the dusk simulation function if you want the light and or the sound of the Wake up Light to stay on and dim gradually during a set period of time 15 minutes to 2 hours before you go to sleep The lamp and or sound switch off automatically after th
7. Register your product and get support at www philips com welcome HF3490 PHILIPS HF3490 ENGLISH 8 E parere 10 11 ENGLISH IMPORTANT SAFETY INSTRUCTIONS This portable light has a polarized plug one blade is wider than the other as a feature to reduce the risk of electric shock This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Never use with an extension cord unless the plug can be fully inserted Do not alter he plug Read this user manual carefully before you use the appliance and save it for future reference This appliance is double insulated according to Class Il Fig 1 When using an electric appliance basic precautions should always be followed including the following Danger Water and electricity are a dangerous combination Do not use this appliance in wet surroundings e g in the bathroom or near a shower or swimming pool Do not let water run into the appliance or spill water onto the appliance Fig 2 Warning Check if the voltage indicated on the appliance corresponds to the local voltage before you connect the appliance The appliance is suitable for voltages of 110V to 230V and frequencies of 50Hz to 60Hz If the power cord is damaged do not use the appliance Call 1 866 832 4361 for
8. ain The test automatically stops after 9 hours Using the lamp You can use the top dial to switch on the lamp as a bedside lamp and to set the light intensity To switch on the lamp press the top dial gently and release it Fig 23 Note It takes approx 1 second for the lamp to go on This is normal the lamp needs to heat up Note The lamp does not go on when you press the top dial while the appliance is in the menu Move the top dial up or down to select the light intensity level you prefer Fig 24 You can choose a light intensity between 1 and 20 Note The light intensity you have selected is automatically set as the light intensity level for the alarm as well To switch off the lamp press the top dial gently and release it Note You can also move the top dial up or down to check and or select a light intensity level without pressing the top dial first Radio volume To switch on the radio press the bottom dial gently and release it Fig 25 To select the desired radio frequency manually move the middle dial up or down Fig 26 Tip To scan radio frequencies automatically press and hold the middle dial for approx 2 seconds Tip To make sure you get a good radio signal fully unwind the antenna and move it around until you have found a position at which reception is best To switch off the radio press the bottom dial gently and release it 14 ENGLISH Volume To set the volume move the bottom dial up or down to sele
9. around the appliance when storing it Disposal Dispose of the appliance in accordance with local regulations Your local or national recycling organizations may also have disposal information For assistance call 1 866 832 4361 Assistance For assistance call toll free 1 866 832 4361 or visit our website www philips com 45 Day Money Back Guarantee If you are not fully satisfied with your Philips Wake up Light send the product back along with the original dated sales receipt and we will refund you the full purchase price The Wake up Light must be shipped prepaid by insured mail insurance prepaid and have the original sales receipt indicating purchase price and the date of purchase enclosed We cannot be responsible for lost mail The Wake up Light must be postmarked no later than 45 days after the 16 ENGLISH date of purchase Philips reserves the right to verify the purchase price of the Wake up Light and limit refunds not to exceed suggested retail price To obtain a Money Back Guarantee Return Authorization form call 1 866 832 4361 Please allow 4 6 weeks for delivery of the check Full Two Year Warranty Philips Electronics North America Corporation USA and Philips Electronics Ltd Canada warrant each new Philips product model HF3490 against defects in materials or workmanship for a period of two years from the date of purchase and agree to repair or replace any defective product without charge IMPORTANT
10. ct the volume level you prefer You can choose a volume level between 1 and 20 Note The volume level you select is automatically set as the volume level for the alarm as well Note The iPod iPhone volume setting does not have an effect on the volume setting of the Wake up Light speaker Using your iPod iPhone with the Wake up Light With the base you can use the Wake up Light as a speaker for your iPod iPhone When you put the iPod iPhone in the iPod iPhone station the iPod iPhone is charged automatically The appliance is supplied with 4 iPod iPhone station adaptors to make sure that most common iPod iPhone versions fit properly in the iPod iPhone station You can use the base with the following iPods and iPhones iPod nano 1G iPod nano 2G iPod nano 3G iPod nano 4G iPod Touch iPod Touch 2G iPod 5G video 30GB iPod classic 80GB 120GB iPod 5G video 60GB 80GB Pod classic 160GB iPhone iPhone 3G Note If you have an iPod iPhone that does not fit into the iPod iPhone station with one of the universal adaptors provided with this Wake up Light you can order an adaptor from Apple Place the Wake up Light on the base see section Installing the appliance in chapter Preparing for use Fig 5 If necessary place one of the adaptors in the iPod iPhone station Place your iPod or iPhone in the iPod iPhone station Fig 27 D The word iPod appears on the display and
11. e light intensity level Perhaps you switched off the alarm by setting the control lever to the op position To switch on the alarm set the control lever to the middle position Perhaps the appliance is defective Call 1 866 832 4361 for assistance It takes approx 1 second for the lamp to go on This is normal the amp needs to heat up Perhaps you set a sound level that is too low To set a higher sound level see chapter Using the appliance section Radio volume Perhaps you switched off the alarm by setting the control lever to the Op position f you selected the radio as the alarm sound the radio may be defective Switch on the radio after you switch off the alarm to check if he radio works If it does not work call 1 866 832 4361 for assistance The radio may be defective Call 1 866 832 4361 for assistance Perhaps the broadcast signal is weak Move the middle dial up or down o adjust the frequency and or change the position of the antenna by moving it around Make sure you have unwound the antenna completely Perhaps you switched off the alarm by setting the control lever to the Op position Perhaps you set a sound level and or light intensity level that is too low Set a higher sound and or light intensity level Perhaps there was a power failure that lasted more than approximately 15 minutes In this case the appliance has remembered all settings except the clock time The clock time therefo
12. e set time Follow steps 1 to 5 in section Middle dial in this chapter to select the dusk simulation function and to set the dusk simulation time Note You can choose a time from 15 to 120 minutes 15 30 60 90 or 120 minutes BD After the set time no matter whether only the light and or the radio or your iPod iPhone music are on the appliance switches off both light and sound Display brightness function Select the display brightness function if you want to adjust the brightness of the display Follow steps 1 to 5 in section Middle dial in this chapter to select the display brightness function and to set the display brightness You can choose a display brightness from 1 to 4 Cleaning and maintenance Never use scouring pads abrasive cleaning agents or aggressive liquids such as alcohol or acetone to clean the appliance Regularly remove dust from the outside of the appliance with a dry cloth Always unplug the appliance before you clean it Clean the outside of the appliance with a dry cloth Do not let water run into the appliance or spill water onto the appliance Fig 28 This appliance has no other user serviceable parts For assistance call 1 866 832 4361 Storage If the appliance will not be used for an extended period of time remove the power cord from he wall outlet and store the appliance in a safe dry location where it will not be crushed banged or subject to damage Do not wrap the power cord
13. ght properly on the base Make sure that the power cord and or the antenna are not stuck between he base and the Wake up Light Perhaps the plug of the Wake up Light is not inserted properly in the wall outlet Put the plug properly in the wall outlet Perhaps there has been a power failure The music played by the Perhaps you did not place the iPod iPhone properly in the iPod iPhone iPod iPhone does not station Make sure you place the iPod iPhone correctly on the iPod come out of the iPhone station See chapter Using the appliance section Using the speaker of the Wake up iPod iPhone Light Perhaps you set a sound level that is too low Set a higher sound level See chapter Using the appliance section Radio volume The alarm sound with Perhaps the playlist in your iPod iPhone is empty Make sure you put the iPod iPhone music your favorite music in the playlist did not work Perhaps you did not select the iPod iPhone as the alarm sound Select he iPod iPhone as alarm sound when you set the alarm See chapter Using the appliance section Setting the alarm sound The controls on iPod Perhaps the iPod iPhone was not working properly Iry to restart the iPhone did not work iPod iPhone PHILIPS E www philips com 4222 002 7501 2
14. ight The Philips Wake up Light gently prepares your body for waking up during the last half hour of sleep In the early morning hours our eyes are more sensitive to light than when we are awake During that period the relatively low light levels of a simulated natural sunrise prepare our body for waking up and getting alert People who use the Wake up Light wake up more easily have a better overall mood in the morning and feel more energetic Because the sensitivity to light differs per person you can set the light intensity of your Wake up Light to a level that matches your light sensitivity for an optimal start of the day For more information about the Wake up Light see www philips com 10 ENGLISH General description Fig 4 Vents Lamp housing Power cord Antenna Display Light symbol Hour indication of clock time alarm time Clock time symbol Alarm symbol iPod iPhone symbol Radio symbol Birds sound symbol Beep sound symbol African jungle sound symbol 10 Wind chimes sound symbol 11 Dusk simulation symbol 12 Display brightness symbo 13 Minute indication of clock alarm time 14 Sound level symbol F Dials on the side of the appliance 1 Top dial light on off and light intensity 2 iddle dial menu and radio frequency 3 Bottom dial radio on off and volume G Control lever with alarm off alarm on and snooze positions H J OMNKHDUAWNAMOOQW gt D
15. larm Fig 12 gt The hour indication of the alarm time flashes Fig 13 BD To adjust the alarm time follow steps 2 to 5 below If the alarm time is correct just wait a few seconds Move the middle dial up or down to select the hour Note You can only do this when the hour indication flashes If this is not the case push the control lever up and down again to enter the alarm time function Note You can also use the middle dial to select the alarm time function and set the alarm time see section Middle dial in this chapter Press the middle dial gently and release it to confirm Dd The minute indication of the alarm time starts to flash Fig 14 Move the middle dial up or down to select the minutes Press the middle dial gently and release it to confirm or wait for a few seconds Dd The appliance leaves the menu and the display shows the clock time The alarm time is now set Switching off the alarm To switch off the alarm push up the control lever to the top position Note The lamp stays on Press the top dial gently and release it to switch off the lamp Note The alarm sound and or light automatically switches off after 90 minutes Setting the alarm sound Follow steps 1 to 5 in section Middle dial in this chapter You can choose one of the following sounds Music from your iPod iPhone see section Using your iPpod iPhone as alarm sound below Fig 15 Radio Fig 16 Birds Fig 17
16. ons Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problem This booklet is available from the U S Government Printing Office Washington DC 20402 Please specify stock number 004 000 00345 4 when ordering copies This equipment has been type tested and found to comply with the specifications in Subpart J of Part 15 of FCC Rules Introduction Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome The Philips Wake up Light helps you wake up more pleasantly The light intensity of the lamp gradually increases to the set level in the 30 minutes before the set wake up time The light gently prepares your body for waking up at the programmed time To make waking up an even more pleasant experience you can use natural wake up sounds the FM radio or even music from your own iPod iPhone The Wake up Light can be used as a speaker for your iPod iPhone which is charged automatically when it is connected to the Wake up Light You can use the dusk simulation function to have the Wake up Light dim the light and sound gradually before they are completely switched off at the time you set Note Only the HF3490 supports the iPod iPhone function The iPod iPhone function is not supported by other Philips Wake up Lights The effects of the Wake up L
17. ove the dials Perhaps the plug is not inserted properly in the wall outlet Put the plug properly in the wall outlet Perhaps there is a power failure Check if the power supply works by connecting another appliance Perhaps the lamp has reached the end of its life The lamp has an expected life of more than 10 000 hours more than 7 years of normal use The life depends on the use of the appliance In case of heavy use the lamp may not last as long as you expect The lamp is not replaceable If the lamp stops working call 1 866 832 4361 for assistance This is normal as the appliance is heated up by the light of the lamp and the electronics Remove the plug from the wall outlet and reinsert it If you reinsert the plug within approximately 15 minutes the appliance remembers all settings If you reinsert the plug after a longer period of time the appliance remembers all settings except the time The lamp does not go on when the alarm goes off The lamp does not go on right away when switch it on do not hear the alarm sound when the alarm goes off The radio does not work The radio produces a crackling sound The alarm went off yesterday but it did not go off today The alarm did not go off 9 minutes after pushed the control lever down to snooze The light wakes me too early ENGLISH 17 Problem Solution Perhaps you set a light intensity level that is too low Increase th
18. p chapter Using the appliance If you often wake up too early or with a headache reduce the light level ENGLISH 9 If you share a bedroom with someone else this person may unintentionally wake up from the light of the appliance even though this person is further removed from the appliance This is the result of differences in light sensitivity between people FCC Information This device generates and uses radio frequency RF energy and if not installed and used properly this equipment may cause interference to radio and television reception These rules are designed to provide reasonable protection against radio and television interference in a residential installation However there is no guarantee that interference will not occur in particular installations If this equipment does cause interference to radio or television reception which you can determine by unplugging the unit try to correct the interference by one or more of the following measures Reorient the receiving antenna that is the antenna for the radio or television that is receiving the interference Move the unit away from the equipment that is receiving interference Plug the unit into a different wall outlet so that the unit and the equipment receiving interference are on different branch circuits If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggesti
19. re flashes on the display Set the correct clock time Perhaps you pushed the control lever down with so much force that it jumped to off position Perhaps you set the volume level to 0 shown on the display as OFP Perhaps the light intensity level you have set is not appropriate for you Try a lower light intensity level if you wake up too early If light intensity 1 is not low enough move the appliance further away from the bed 18 ENGLISH Problem Solution The light wakes me too Perhaps the appliance is positioned at a lower level than your head late ake sure the appliance is located at a height at which the light is not blocked by your bed comforter blanket or pillow Also make sure the appliance is not placed too far away The lamp flashes Perhaps there has been a power failure It is normal for the lamp to flash after a power failure Perhaps the appliance is not suitable for the voltage to which it is connected Make sure that the voltage indicated on the appliance corresponds to the local voltage The iPod iPhone was Perhaps you did not place the iPod iPhone properly in the iPod iPhone not charged after station Make sure you place the iPod iPhone correctly in the iPod placed it in the iPod iPhone station See chapter Using the appliance section Using the iPhone station iPod iPhone Perhaps you had not placed the Wake up Light properly on the base ake sure you place the Wake up Li
20. u and the display shows the set clock time The appliance is now ready for use Note Every time you remove the plug from the wall outlet for more than approximately 15 minutes you have to set the clock time again by following steps 1 to 4 above Note To change the set clock time when the plug is still in the wall outlet press the middle dial gently two times to enter the menu for setting the clock time You are in the menu when the hour indication flashes Then follow steps 1 to 4 above Using the appliance Use this appliance for its intended household use as described in this manual Top and bottom dials With the top dial you can switch the lamp on or off and set the light intensity see section Using the lamp in this chapter With the bottom dial you can switch the radio on or off and set the volume see section Radio volume in this chapter Note Press the dial gently and release it to switch on or off the light top dial or radio bottom dial and move the dial up or down to change the light intensity top dial or volume level bottom dial Middle dial The middle dial allows you to choose various functions from the menu These functions appear in the menu in the following order Clock time Alarm time Alarm sound Dusk simulation function Display brightness function You can operate the middle dial in the following way Press the middle dial gently and release it to enter the menu Fig 10 Do
Download Pdf Manuals
Related Search