Philips LCD monitor 190E2FB
Contents
1. Please find out about the local regulations on how to dispose of your old monitor and packing from your sales representative Recycling Information for Customers There is currently a system of recycling up and running in the European countries such as The Netherlands Belgium Norway Sweden and Denmark In Asia Pacific Taiwan the products can be taken back by Environment Protection Administration EPA to follow the IT product recycling management process detail can be found in web site www epa gov tw The monitor contains parts that could cause damage to the nature environment Therefore it is vital that the monitor is recycled at the end of its life cycle For help and service please contact Consumers nformation Center or First Choice Contact Information Center in each country 2 Setting up the monitor 2 1 Installation EM Package contents PHILIPS Monitor Quick start guide E Base stand EDFU CD EE r LA Eje Power cord VGA signal cable optional EJ Install base stand 1 Place the monitor face down a smooth surface taking care to avoid scratching or damaging the screen Then lift the monitor stand 2 Hold the monitor base stand with both hands and firmly insert the base stand into the base column EJ Connecting to your PC Q Kensington anti thief lock C power input DVI D input available for selecting2. after imaging or ghost imaging is a well known phenomenon in LCD panel technology In most cases the burned in or after imaging or ghost imaging will disappear gradually over a period of time after the power has been switched off O Warning Severe burn in or after image or ghost image symptoms will not disappear and cannot be repaired The damage mentioned above is not covered under your warranty Service The casing cover should be opened only by qualified service personnel fthere is any need for any document for repair or integration please contact with your local service center please refer to the chapter of Consumer Information Center e For transportation information please refer to Technical Specifications Do not leave your monitor in a car trunk under direct sun light amp Note Consult a service technician if the monitor does not operate normally or you are not sure what procedure to take when the operating instructions given in this manual have been followed 1 2 Notational Descriptions The following subsections describe notational conventions used in this document Notes Cautions and Warnings Throughout this guide blocks of text may be accompanied by an icon and printed in bold or italic type These blocks contain notes cautions or warnings They are used as follows amp Note This icon indicates important information and tips that help you make better use of
3. NEW ZEALAND Company Visual Group Ltd Address 28 Walls Rd Penrose Auckland Phone 0800 657447 Fax 09 5809607 E mail vai ravindranQvisualgroup co nz Service Hours Mon Fri 8 30am 5 30pm Asia HONG KONG Macau Company Name PHK Service Limited Address Flat A 10 F Pak Sun Building 103 107 Wo Yi Hop Road Kwai Chung New Territories Hong Kong Tel 852 2610 6908 852 2610 6929 for Hong Kong and 853 2856 2277 for Macau Fax 852 2485 3574 for Hong Kong and 853 2856 1498 for Macau E mail enquiry phkservice com hk Service Hours Mon Sat 09 00am 06 00pm India Company REDINGTON INDIA LTD Address SPL Guindy House 95 Mount Road Chennai 600032 India Tel 9144 42243352 353 E mail aftersales in aocmonitorcom Service hours Mon Fri 9 00AM 5 30PM Sat 9 00AM 1 00PM Indonesia Company Name PT Gadingsari elektronika Prima Address Kompleks Pinang 8 Jl Ciputat raya No 8F Pondok Pinang Jakarta Tel 021 750909053 021 750909056 Fax 021 7510982 E mail gepta cbn net id Service hours Mon Fri 8 30am 4 30pm Sat 8 30am 2 00pm Additional service points 1 Philips Building JI Buncit Raya Kav 99 Jakarta Selatan Phone 021 7940040 ext 1722 1724 98249295 70980942 2 Jl Tanah Abang 1 no 12S Jakarta Pusat Phone 021 3455150 34835453 3 Rukan City Home no H31 Gading Square Bulevar Barat Kelapa Gading Jakarta Utara Phone 021 45870601 98131424 So
4. a sub pixel that stands out on the screen when he monitor displays a dark pattern There are the ypes of bright dot defects One lit red green or blue sub pixel Two adjacent lit sub pixels Red Blue Purple Red Green Yellow Green Blue Cyan Light Blue Three adjacent lit sub pixels one white pixel 10 amp Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots BE Black Dot Defects Black dot defects appear as pixels or sub pixels hat are always dark or off That is a dark dot is a sub pixel that stands out on the screen when Proximity of Pixel Defects he monitor displays a light pattern These are the Because pixel and sub pixels defects of the same ypes of black dot defects ype that are near to one another may be more noticeable Philips also specifies tolerances for the proximity of pixel defects i Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables BRIGHT DOT DEFECTS ACCEPTABLE LEVEL 3 adjacent lit subpixels one white pixel 0 ek BLACK DOT DEFECTS ACCEPTABLE LEVEL MODER 190E2 plus 2
5. fnych zafizeni je u ivatel povinnen prov st takov opatfgni aby ru en odstranil uvedeno e spad do do t idy A podle EN 55022 17 Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit a three prong socket All equipment that works together computer monitor printer and so on should have the same power supply source The phasing conductor of the room s electrical installation should have a reserve short circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes A lo comp power supply cab power supply soc near the equipme etely switch off the equipment the e must be removed from the et which should be located nt and easily accessible A protection mark B confirms that the equipment is in compliance with the protection usage requirements of standards PN 93 1 42107 and PN 89 E 06251 Wymagania Polskiego Centrum Bada i Certyfikacji Urz dzenie powinno by zasi ane z gniazda z przy czonym obwodem ochronnym gniazdo ko kiem Wsp pracuj ce ze sob urz dzenia kampuse monitor drukarka powinny by zasilane Instalacja elektryczna pomieszczenia powinna zawiera w przewodzie fezowym reszrwowa ochrong 1 role um ka o warto ci znamionowej nie wi kszej ni 16A amper w e po Zauk bezpiecze stwa B potwierdza zgodno wymaganiami bezpie
6. adjacent dark subpixels 3 adjacent dark subpixels 229 1 dark subpixel TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL 190E2 plus Total bright or black dot defects of all types e Note 1 or 2 adjacent sub pixel defects 1 dot defect This monitor is ISO9241 307 compliant 11 4 Technical Specifications 160 H 160 V CR gt 10 Vertical refresh rate 56Hz 6Hz orizontal Frequency 30kHz 83kHz sRGB MES Signal input DVI D digital HDCP VGA Analog Input Signal Separate Sync Sync on Green o we f e wan OSD Languages English French German Italian Russian Spanish Simplified Chinese Portuguese Other convenience Kensington lock Plug amp Play Compatibility DDC CI sRGB Windows 7 Vista XR Mac OSX Linux EET 12 Product with stand WxHxD 443 x 368 x 170mm Product without stand 443 x 299 x 65mm WxHxD Box dimension WxHxD 503 x 416 x 141mm 3 8kg 35kg Product with packaging 5 1kg Temperature range Storage 20 C to 60 C operation O C to 40 C Altitude Non operation 40 000 ft 12 192 m ROHS 100 recyclable Regulatory Approvals CE Mark FCC Class B SEMKO UL cUL ISO9241 307 Black Black e Note This data is subject to change without notice Go to www philips com support to download the latest version of leaflet 13 4 1 Resolution amp Preset Modes 4 2 Automatic PowerSaving KI Maximum Resolution
7. adjustments or procedures other than those specified in this documentation may result in exposure to shock electrical hazards and or mechanical hazards Read and follow these instructions when connecting and using your computer monitor Operation Keep the monitor out of direct sunlight and away from stoves or any other heat source e Remove any object that could fall into ventilation holes or prevent proper cooling of the monitors electronics Do not block the ventilation holes on the cabinet When positioning the monitor make sure the power plug and outlet are easily accessible f turning off the monitor by detaching the power cable or DC power cord wait for 6 seconds before attaching the power cable or DC power cord for normal operation Please use approved power cord provided by Philips all the time If your power cord is missing please contact with your local service center Please refer to Customer Care Consumer Information Center This electronic user s guide is intended for anyone Do not subject the monitor to severe vibration or high impact conditions during operation Do not knock or drop the monitor during operation or transportation Maintenance To protect your monitor from possible damage do not put excessive pressure on the LCD panel When moving your monitor grasp the frame to lift do not lift the monitor by placing your hand or fingers on the LCD panel Unplug the monitor if y
8. enable SmartImage Lite 1 Press to BD launch the SmartImage Lite on screen display 2 Keep pressing ED to toggle between Standard Internet and Game 3 The Smartlmage Lite on screen display will remain on screen for 5 seconds or you can also press OK to make confirmation 4 When Smartlmage Lite is enabled the sRGB scheme is disabled automatically To use sRGB you need to disable Smartlmage Lite with the ED button at the front bezel of your monitor Except using EP key to scroll down you can also press w A buttons to choose and press OK to confirm selection and close the Smartlmage Lite OSD There are 3 modes to be selected Standard Internet and Game ED Smart Image Lite Standard Standard Enhances text and dampens brightness to increase readability and reduce eye strain This mode significantly enhances readability and productivity when you re working with spreadsheets PDF files scanned articles or other general office applications Internet This profile combines color saturation dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors all without artifacts and faded colors Game Turn on over drive circuit for best response time reduce jaggy edges for fast moving objects on screen enhance contrast ratio for bright and dark scheme this profile delivers the best gaming experience for gamers 3 2 SmartCo
9. model VGA input Connect to PC Connect the power cord to the back of he montior firmly 2 Turn off your computer and unplug its power cable 3 Connect the monitor signal cable to the video connector on the back of your computer 4 Plug the power cord of your computer and your monitor into a nearby outlet 5 Turn on your computer and monitor If is complete 2 2 Operating the monitor EI Front view product description G o Z A va 6000000 of o0 Ep he monitor displays an image installation To switch monitors power on and off To access OSD menu To adjust the OSD menu Change to 4 3 display To change the signal input v Auro Automatically adjust the horizontal position vertical position phase and clock settings Return to previous OSD level To adjust brightness of the display Smartlmage Lite There are 3 modes to be selected Standard Internet and Game EJ Description of the On Screen Display What is On Screen Display OSD On Screen Display OSD is a feature in all Philips LCD monitors It allows an end user to adjust screen performance or select functions of the monitors directly through an on screen instruction window A user friendly on screen display interface is shown as below Monitor Setup Input Back Basic and simple instruction on the control keys In the OSD shown above users can press y
10. 190E2 plus PHILIPS www philips com welcome EN User manual 1 Customer care and warranty 20 Troubleshooting amp FAQs 32 PHILIPS Table of Contents 1 1 1 2 1 3 2 1 22 2 3 34 32 33 NNN OWS NS Important enden Safety precautions and maintenance Notational Descriptions Disposal of product and packing material 3 Setting up the monitor 4 Installation Operating the monitor S Remove Base Stand and Base WA Product information 4 9 Smarth mage Bite 8 SmartC OMURASE canine nid cda 9 Philips Flat Panel Monitors Pixel DESCUPOI GR ee 10 Technical Specifications 12 Resolution amp Preset Modes grali Automatic PowerSaving elf Regulatory Information 15 Customer care and Warranty 20 Troubleshooting amp FAQs 32 Troubleshooting 32 General EAS nee 34 1 Important who uses the Philips monitor lake time to read this user manual before you use your monitor It contains important information and notes regarding operating your monitor The Philips guarantee applies provided the product is handled properly for its intended use in accordance with its operating instructions and upon presentation of the original invoice or cash receipt indicating the date of purchase dealer s name and model and production number of the product 1 1 Safety precautions and maintenance A Warnings Use of controls
11. 2101969 SERBIA amp MONTENEGRO Kim Tec d o o Viline vode bb Slobodna zona Beograd L12 3 11000 Belgrade Serbia Tel 381 11 20 70 684 SLOVAKIA General Consumer Information Center 0800004551 Datalan Servisne Stredisko Puchovska 8 SK 831 06 Bratislava Tel 421 2 49207155 Email servis datalan sk SLOVENIA PC HAND Brezovce 10 SI 1236 Trzin Tel 386 1 530 08 24 Email servis pchand si RUSSIA CPS 18 Shelepihinskaya nab 123290 Moscow Russia Tel 7 495 797 3434 Profservice 14A 3 2Karacharovskaya str 109202 Moscow Russia Tel 7 095 170 5401 TURKEY T rk Philips Ticaret A S Yukari Dudullu Org San Bolgesi 2 Cadde No 22 34776 Umraniye lstanbul Tel 0800 261 33 02 UKRAINE Comel Shevchenko street 32 UA 49030 Dnepropetrovsk Tel 4 380 562320045 www csp comel com LLC Topaz Company Topaz Service Company Mishina str 3 Kiev Ukraine 03151 Tel 38 044 245 73 31 Latin America ARGENTINA Azopardo 1480 C1107ADZ Cdad de Buenos Aires Tel 0800 3330 856 Email CIC monitores Philips com BRASIL Alameda Raja Gabaglia 188 10 Andar V Ol mpia S Paulo SP CEP 04551 090 Brasil Tel 0800 7254101 Email CIC monitores Philips com Pacific AUSTRALIA Company AGOS NETWORK PTY LTD Address 4 5 Dursley Road Yenorra NSW 2161 Australia Tel 1300 360 386 Fax 61 2 80808147 Email philips agos com au Service hours Mon Fri 8 00am 7 30pm
12. EW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE Austria Belgium Denmark France Germany Greece Finland Ireland Italy Luxembourg the Netherlands Norway Portugal Sweden Switzerland Spain United Kingdom Poland EASTERN EUROPE Czech Republic Hungary Russia Slovakia Slovenia Turkey LATIN AMERICA Argentina Brasil NORTH AMERICA Canada USA PACIFIC Australia New Zealand ASIA China Hong Kong India Indonesia Korea Malaysia Pakistan Philippines Singapore Taiwan Thailand Vietnam AFRICA South Africa MIDDLE EAST United Arab Emirates Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor All Philips monitors are designed and manufactured to high standards and deliver high quality performance ease of use and ease of installation Should you encounter any difficulties while installing or using this product please contact the Philips helpdesk directly to benefit from your Philips First Choice Warranty This two year service warranty entitles you to a swap model on site if your monitor turns out to be faulty or defective Philips aims at a swap within 48 hours of your call being received What is covered The Philips First Choice Warranty applies within Andorra Austria Belgium Cyprus Denmark France Germany Greece Finland Ireland Italy Liechtenstein Luxembourg Monaco the Netherlands Norway Poland Portugal S
13. If you have VESA DPM compliance display card or software installed in your PC the monitor can automatically reduce its power consumption when not in use If an input from a keyboard mouse or other input device is detected the monitor will wake up automatically The following table shows the power consumption and signaling of this For 190E2 plus 1440 x 900 at 60 Hz analog input 1440 x 900 at 60 Hz digital input El Recommended Resolution automatic power saving feature VESA Video H sync V sync Power Used LED color Mode For 190E2 plus 1440 x 900 at 60 Hz digital input 31 469 70 086 31 469 59 940 35 000 67 000 37 500 75 000 35456 800x600 56250 The following setup is used to measure power 37879 800x600 60317 consumption on this monitor BOA D W RAM Native resolution 1440 x 900 48 363 1024x768 60 004 Contrast 50 60 023 1024x768 75 029 Brightness 250 nits 63 981 1280x1024 60 020 Color temperature 6500k 19 976 1280x1024 121025 55955 1440x900 59 887 G Note 70 635 1440x900 74 984 This data is subject to change without notice Sleep OFF No No lt 08W typ White Blinking Switch Of or lt 05w yp OFF 14 prEN50279 1998 Low Frequency Electric and 5 Regulatory Information Magnetic fields for Visual Display e MPR II MPR 1990 8 1990 10 Low Frequency Lead free Product Electric and Magnetic fields Lead free display promotes Z environm
14. OITUS SIJOITA LAITE SITEN ETTA VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA Plassering Venti ADVARSEL N R DETTE DU PASSE lasjon UTSTYRET PLASSERES MA PA AT KONTAKTENE FOR STOMTILFORSEL ER LETTE A NA BSMI Notice Taiwan Only F LH MEMRCZIRE Ergonomie Hinweis nur Deutschland Der von uns gelieferte Farbmonitor entspricht den in der Verordnung ber den Schutz vor Sch den durch R ntgenstrahlen festgelegten Vorschriften Auf der R ckwand des Ger tes befindet sich ein Aufkleber der auf die Unbedenklichkeit der Inbetriebnahme hinweist da die Vorschriften ber die Bauart von St rstrahlern nach Anlage Ill 2 5 Abs 4 der R ntgenverordnung erf llt sind Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht ist darauf zu achten da 1 Reparaturen nur durch Fachpersonal durchgef hrt werden 2 nur original Ersatzteile verwendet werden 3 bei Ersatz der Bildr hre nur eine bauartgleiche eingebaut wird Aus ergonomischen Gr nden wird empfohlen die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden schlechte Lesbarkeit und erh hte Augenbelastung bei zu geringem Zeichenkontrast waren die Folge Der arbeitsplatzbezogene Schalldruckpegel nach 35 betragt OdB A oder weniger TUNG BEIM AUFSTELLEN DIESES GER TES DARAUF ACHTEN DAB NETZSTECKER UND NETZKABELANSCHLUB LEICHT ZUG NGLICH SIND China RoHS The Peop
15. Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device To prevent damage which may result in fire or shock hazard do not expose this appliance to rain or excessive moisture THIS CLAS
16. S B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS television reception which can be determined FCC Declaration of Conformity Declaration of Conformity for Products Marked with FCC Logo United States Only FC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 16 Commission Federale de la Communication FCC Declaration Cet quipement a t test et d clar conforme auxlimites des appareils num riques de class B aux termes de l article 15 Des r gles de la FCC Ces limites sont concues de facon fourir une protection raisonnable contre les interf rences nuisibles dans le cadre d une installation r sidentielle CET appareil produit utilise et peut mettre des hyperfr quences qui si l appareil n est pas install et utilis selon les consignes donn es peuvent causer des interf rences nuisibles aux communications radio Cependant rien ne peut garantir l absence d interf rences dans le cadre d une installation particuli re Si cet appareil est la cause d interf rences nuisibles pour la r ception des signaux de radio ou de t l vision ce qui peut tre d cel en fermant l quipement puis en e remettant en fonction l uti
17. a buttons at the front bezel of the monitor to move the cursor OK to confirm the choice or change The OSD Menu Below is an overall view of the structure of the On Screen Display You can use this as a reference when you want to work your way around the different adjustments later on Main menu Sub menu VGA Input I DVI available for selective models Picture Format Wide screen 4 3 Picture L Brightness 0 100 Fr Contrast 0 100 H SmartContrast On Off Gamma 18 2 0 2 2 2 4 2 6 Color Temp 5000K 6500K 7500K 8200K 9300K 11500K I Color H sRGB User Define p Red 0 100 H Green 0 100 Blue 0 100 Language English Espanol Francais Deutsch Italiano Portugu s Pycckni Ej ep gt Z Horizontal 0 100 OSD Setting H Vertical 0 100 Transparency Of 1 2 3 4 OSD Time out 5 10 20 30 60 r Power LED 01 23 4 Setup H Position 0 100 V Position 0 100 Phase 0 100 Clock 0 100 I Resolution Notification On Off Reset Yes No Information EJ Resolution notification 2 3 Remove Base Stand and Base This monitor is designed for optimal performance R he Base Stand at its native resolution 1440x900 60Hz El Remove the Base Stan When the monitor is powered on at a different resolution an alert is displayed on screen U
18. anual adjustments via the OSD menu G Note The Auto Function is not applicable in DVI Digital mode as it is not necessary Visible signs of smoke or sparks Do not perform any troubleshooting steps Disconnect the monitor from mains power source immediately for safety Contact with Philips customer service representative immediately El Imaging Problems Image is not centered e Adjust the image position using the Auto function in OSD Main Controls e Adjust the image position using the Phase Clock of Setup in OSD Main Controls It is valid only inVGA mode Image vibrates on the screen Check that the signal cable is properly securely connected to the graphics board or PC Vertical flicker appears e Adjust the image using the Auto function in OSD Main Controls e Eliminate the vertical bars using the Phase Clock of Setup in OSD Main Controls It is valid only in VGA mode Horizontal flicker appears WI Adjust the image using the Auto function in OSD Main Controls Eliminate the vertical bars using the Phase Clock of Setup in OSD Main Controls It is valid only in VGA mode U Image appears blurred indistinct or too dark Adjust the contrast and brightness on On Screen Display An after image burn in or ghost image remains after the power has been turned off Uninterrupted display of still or static images over an extended period may cause bu
19. aphic card name and driver version o Operating system o Application being used Other cards installed Having the following information available will also help speed up the process Your proof of purchase indicating date of purchase dealer name model and product serial number The full address to which the swap model should be delivered Just a phone call away Philips customer help desks are located worldwide Within the U S you can contact Philips customer care Monday Friday from 8 00 AM 9 00 PM Eastern Time ET and on Saturdays from 10 00 AM 5 00 PM ET hrs by using one of the contact phone numbers For more information on this and more great Philips products visit our website at Website http www philips com 30 Your International Guarantee Dear Customer Thank you for purchasing this Philips product which has been designed and manufactured to highest quality standards the f unfortunately something should go wrong with his product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase This international Philips guarantee complements the existing national guarantee obligations to you of dealers and Phi in the country of purchase and does not affect your statutory rights as a customer ips The Philips guarantee applies provided the product is handled properly
20. cze stwa u ytko minis znanymi w Pi A T 42107 TPN KOE 1 Pozosta e instrukcje bezpiecze stwa Nie nale y u ywa wtyczek adapterowych lub usuwa ko ka obwodu ochronnego z wtyczki Je eli konieczne jest u ycie pezed u acza to nale y u y przed u acza 3 2ylowego z prawid owa po czonym przewodem ochronnym System ko kami napi bezzakl ce Nale y upewni byty umieszcza lerowy nale y zabezpieczy przed nag ymi chwilowymi wzrostami lub spad ywaj c eliminatora przepi urz dzenia dopasowujacego lub r d a zasilania ach systemu komputerowego oraz aby kable nie yloby na nie nadeptywa lub potykac si o nie rozlewa napoj w ani innych ply wpycha adnych przedmiot w do atwor w systemu kompi ta spowodowa po ar lub pora enie pr dem poprzez zwarcie elements system komputerowy n komputerowy powinien znajdowa si z dala od grzejnik w i r di le y blakawa atwor w w nych Nale y unika k adzenia lu komputer oraz umieszczania komputera w ciasnym miejscu bez mo liwosci cyrkulacji powi etrza wok niego 18 North Europe Nordic Countries Information Placering Ventilation VARNING FORSAKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG AR LATATKOMLIGA NAR DU STALLER DIN UTRUSTNING PAPLATS Placering Ventilation ADVARSEL SORG VED PLACERINGEN FOR AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGAENGELIGE Paikka llmankierto VAR
21. d the operating instructions carefully before contacting your dealer If you have questions which your dealer cannot answer or any related question please contact the Philips Consumer Information Centers or via Website http www philips com 7 Troubleshooting amp FAQs 7 1 Troubleshooting This page deals with problems that can be corrected by a user If the problem still persists after you have tried these solutions contact Philips customer service representative El Common Problems No Picture Power LED not lit Make sure the power cord is plugged into the power outlet and into the back of the monitor e First ensure that the power button on the front of the monitor is in the OFF position then press it to the ON position No Picture Power LED is white blinking e Make sure the computer is turned on e Make sure the signal cable is properly connected to your computer make sure the monitor cable has no bent pins on the connect side If yes repair or replace the cable The Energy Saving feature may be activated Screen says ATTENTION CHECK CABLE CONNECTION e Make sure the monitor cable is properly connected to your computer Also refer to the Quick Set Up Guide Check to see if the monitor cable has bent pins Make sure the computer is turned on AUTO button doesn t function The auto function is applicable only in VGA Analog mode If the result is not satisfactory you can do m
22. entally sound recovery and isposal of waste from electrical and electronic equipment Toxic substances like Lead has been eliminated and compliance with European community s stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life cycle Q CE Declaration of Conformity This product is in conformity with the following standards EN60950 1 2006 Safety requirement of nformation Technology Equipment e EN55022 2006 Radio Disturbance requirement of Information Technology Equipment e EN55024 1998 A1 2001 A2 2003 Immunity requirement of Information Technology Equipment EN61000 3 2 2006 Limits for Harmonic Current Emission e EN61000 3 3 1995 A1 2001 A2 2005 Limitation of Voltage Fluctuation and Flicker following provisions of directives applicable e 2006 95 EC Low Voltage Directive 2004 108 EC EMC Directive 2005 32 EC EuP Directive EC No 1275 2008 mplementing Directive for Standby and Off mode power consumption and is produced by a manufacturing organization on ISO9000 level The product also comply with the following standards 1509241 307 2008 Ergonomic requirement Analysis and compliance test methods for electronic visual displays GS EK1 2000 2009 GS mark requirement 15 Federal Communications Commission FCC Notice U S
23. for its intended use in accordance with its operating instructions and upon presentation of the original invoice or cash receipt indicating the date of purchase dealer s name and model and production number of the product The Philips guarantee may not apply if e the documents have been altered in any way or made illegible e the model or production number on the product has been altered deleted removed or made illegible repairs or product modifications and alterations have been executed by unauthorized service organizations or persons damage is caused by accidents including but not limited to lightning water or fire misuse or neglect 31 Please note that the product is not defective under this guarantee in the case where modifications become necessary in order for the product to comply with local or national technical standards which apply in countries for which the product was not originally designed and or manufactured Therefore always check whether a product can be used in a specific country In case your Philips product is not working correctly or is defective please contact your Philips dealer In the event you require service whilst in another country a dealer address can be given to you by the Philips Consumer Help Desk in that country the telephone and fax number of which can be found in the relevant part of this booklet In order to avoid unnecessary inconvenience we advise you to rea
24. g or Image Burn in or After Image or Ghost Image in LCD panels Ans Uninterrupted display of still or static images over an extended period may cause burn in also known as after imaging or ghost imaging on your screen Burn in after imaging or ghost imaging is a well known phenomenon in LCD panel technology In most cases the burned in or atter imaging or ghost imaging will disappear gradually over a period of time after the power has been switched off Always activate a moving screen saver program when you leave your monitor unattended Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content A Warning Severe burn in or after image or ghost image symptoms will not disappear and cannot be repaired The damage mentioned above is not covered under your warranty Q13 Why is my Display not showing sharp text and is displaying jagged characters Ans Your LCD monitor works best at its native resolution of 1440x900 60Hz For best display please use this resolution 36 2010 Koninklijke Philips Electronics N V All rights reserved Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips Electronics N V and are used under license from Koninklijke Philips Electronics N V Specifications are subject to change without notice Version 190E2 plus v1 0 PHILIPS
25. g years two 28 WHO IS COVERED You must have proof of purchase to receive warranty service A sales receipt or other document showing that you purchased the product is considered proof of purchase Attach it to this owner s manual and keep both nearby WHAT IS COVERED Warranty coverage begins the day you buy your product For two years thereafter all parts will be repaired or replaced and labor is free After two years from the day of purchase you pay for the replacement or repair of all parts and for all labor charges All parts including repaired and replaced parts are covered only for the original warranty period When the warranty on the original product expires the warranty on all replaced and repaired products and parts also expires WHAT IS EXCLUDED Your warranty does not cover labor charges for installation or setup of the product adjustment of customer controls on the product and installation or repair of antenna systems outside of the product product repair and or part replacement because of misuse accident unauthorized repair or other cause not within the control of Philips Consumer Electronics reception problems caused by signal conditions or cable or antenna systems outside the unit a product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of pr
26. i 3 Road Wangthonglang Bangkok 10310 Thailand Tel 662 934 5498 Fax 662 934 5499 E mail axis5QQaxiscomputerco th Service Hours Mon Fri 08 30am 05 30pm Glee Electronics Inc Contact nos 632 636 3636 7064028 to 29 Fax no 632 7064026 Receiving Centers EO CARE Megamall th Level Cyberzone Building B Megamall Mandaluyong City n A NEO CARE SM North EDSA 4th Level Cyberzone Annex Bldg SM City North EDSA Quezon City 441 1610 MDR Microware Sales Inc Cebu Branch N Escario corner Clavano St Cebu City Phils 255 4415 255 3242 253 9361 4124864 to 67 Sun 0922 8210045 to 46 Davao Office C Arellano St Davao City 8000 082 225 3021 225 3022 Sun 0922 8210015 CDO Office 1445 Corrales Ext CDO City 088 856 8540 856 8541 Sun 0922 8210080 lloilo Office C Lim Comp Gomez St lloilo City H 033 338 4159 033 508 3741 Sun 0922 8808850 Africa SOUTH AFRICA Company name Sylvara Technologies Pty Ltd Address Ho Address Palm Springs Centre Christoffel Road Van Riebeeck Park Kempton Park South Africa Tel 27878084456 Fax 2711 391 1060 E mail customercareQphilipssupport co za Service hours Mon Fri 08 00am 05 00pm Middle East Middle East North Africa Company AL SHAHD COMPUTER L L C Address POBOX 29024 DUBAI UNITED ARAB EMIRATES TEL 00971 4 2276525 FAX 00971 4 2276242 E mail shahd52 eim ae Service hours Sat Thur 9 00am 1 00pm am
27. ings in the 5000K range the panel appears warm with a red white color tone while a 11500K temperature yields cool blue white toning sRGB this is a standard setting for ensuring correct exchange of colors between different device e g digital cameras monitors printers scanners etc User Define the user can choose his her preference color setting by adjusting red green blue color amp Note A measurement of the color of light radiated by an object while it is being heated This measurement is expressed in terms of absolute scale degrees Kelvin Lower Kevin temperatures such as 2004K are red higher temperatures such as 9300K are blue Neutral temperature is white at 6504K 35 Q9 Can connect my LCD monitor to any PC workstation or Mac Ans Yes All Philips LCD monitors are fully compatible with standard PCs Macs and workstations You may need a cable adapter to connect the monitor to your Mac system Please contact your Philips sales representative for more information Q10 Are Philips LCD monitors Plug and Play Ans Yes the monitors are Plug and Play compatible with Windows 7 Vista XP NT Mac OSX Linux Q11 What kind of wide angle technology is available Ans Currently the IPS type panels offer the best Contrast Ratio compared to MVA or PVA technologies TN panels have improved over the years but IPS panel still gives superior results over TIN panel Q12 What is Image Stickin
28. kage Monitor drivers inf and icm files will be installed automatically How do I adjust the resolution Your video card graphic driver and monitor together determine the available resolutions You can select the desired resolution under Windows Control Panel with the Display properties What if get lost when am making monitor adjustments via OSD Simply press the OK button then select Reset to recall all of the original factory settings Is the LCD screen resistant to scratches In general it is recommended that the panel surface is not subjected to excessive shocks and is protected from sharp or blunt objects When handling the monitor make sure that there is no pressure or force applied to the panel surface side This may affect your warranty conditions Q7 How should clean the LCD surface Ans For normal cleaning use a clean soft cloth For extensive cleaning please use isopropyl alcohol Do not use other solvents such as ethyl alcohol ethanol acetone hexane etc Q8 Can change the color setting of my monitor Ans Yes you can change your color setting through OSD control as the following procedures Press OK to show the OSD On Screen Display menu Press Down Arrow to select the option Color then press OK to enter color setting there are three settings as below 1 Color Temperature The six settings are 5000K 6500K 7500K 8200K 9300K and 11500K With sett
29. le s Republic of China released a regulation called Management Methods for Controlling Pollution by Electronic Information Products or commonly referred to as China RoHS All products including CRT and LCD monitor which are produced and sold for China market have to meet China RoHS request PELXROHS REPHAR BTR RS RSH INE C MOSPIDXRSROHS DARROW TAP APRA SNA SAMARITANS RMS W AREAL A ETRE OREARCRT BEARER WBE RR ELI LES R L DIL SRE SRZEM Pb He Cd Cr6 PBB PBDE Mx O O O o O O CRTERA x O o O O O BARRE x x O o O e IT CUM x O O o e e EEEE x O O o O BREE x Oo o o O MH FE LE ED HRS RUPES SERIA ane FORE ERER ERES O RTRA BA E MAEAEA ASAR of HS AFER APERA SOR ORR ERIE RERO T X RZA BR BW RED ARAB ES EPAIA AL RFEBFREWSA RAGE NOEIORUESOR EMERYT X HBE RARHROHSZIER RT REA 45 HBE IHR RENT E FT fe P a eH BS A UPS SET SRUSRTEI HE TE FETT ZRAINERRE HER i 11 e J FER RANGE 3 X Beak wy FLA MER BEII PERERA SIR fRIEFREJXKE ERARE KRRAFAUTER FAX BRP BRERA http www energylabel gov cn 6 Customer care and warranty Customer Care amp Warranty PLEASE SELECT YOUR COUNTRY AREA TO REVI
30. lisateur pourrait essayer de corriger la situation en prenant les mesures suivantes R orienter ou d placer l antenne de r ception e Augmenter la distance entre l quipement et e r cepteur Brancher l quipement sur un autre circuit que celui utilis par le r cepteur Demander l aide du marchand ou d un technicien chevronn en radio t l vision Toutes modifications n ayant pas recu l approbation des services comp tents en mati re de conformit est susceptible d interdire l utilisateur l usage du pr sent quipement N utiliser que des c bles RF arm s pour les connections avec des ordinateurs ou p riph riques CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA EN 55022 Compliance Czech Republic Only This device to category B devices as described in EN 55022 unless it is specifi cally stated that it is a Class A device on the specification label The following applies to devioss in Class A of EN 55022 radius of protection up to 30 meters The user of the device is obliged to take all steps necessary to remove sources of interference to tele communication or other devices Pokud neni na typov m titku po ta e spad automaticky do tfidy B podle EN 55022 Pro zafizeni za azen do t dy A chrann p smo 30m podle EN 55022 plat n sleduj c Dojde li k ru en telekomunikatnich nebo
31. lways check whether a product can be used in a specific country Please note that the product is not defective under this guarantee in the case where modifications become necessary in order for the product to comply with local or national technical standards which apply in countries for which the product was not originally designed and or manufactured Therefore always check whether a product can be used in a specific country Just a click away In case of any problems we advise you to read the operating instructions carefully or go to the www philips com support website for additional support Just a phone call away n order to avoid unnecessary inconvenience we advise you to read the operating instructions carefully before contacting our dealers or nformation Centers n case your Philips product is not working correctly or is defective please contact your Philips dealer or directly the Philips Service and Consumer Information Centers Website http www philips com support 23 Consumer Information Centers Argentina Australia Brasil Canada ew Zealand Belarus Bulgaria Croatia Czech Republic Estonia United Arab Emirates Hong Kong Hungary India Indonesia srael Latvia Lithuania Malaysia iddle East North Africa New Zealand Pakistan Romania Russia Serbia amp Montenegro Singapore Slovakia Slovenia South Africa South Korea Taiwan Phili
32. nal conditions or cable or antenna systems outside the unit Defects caused by abuse or misuse of the monitor e Product requires modification or adaptation to enable it to comply with local or national technical standards which apply in countries for which the product was not originally designed manufactured approved and or authorized Therefore always check whether a product can be used in a specific country Note that products that are not originally designed manufactured approved and or authorized for usage within the Philips F1rst Choice countries do not apply to the Philips First Choice Warranty In these cases the Philips global warranty terms are valid 21 Just a click away In case of any problems we advise you to read the operating instructions carefully or go to the www philips com support website for additional support Just a phone call away In order to avoid unnecessary inconvenience we advise you to read the operating instructions carefully or go to the www philips com support website for additional support before contacting the Philips helpdesk To solve your problem quickly please prepare the following details before contacting the Philips helpdesk e Philips type number Philips serial number e Purchase date copy of purchase may be required PC environment Processor o CUP and Graphic card name and driver version o Operating system o Ap
33. nitor with an unacceptable number of defects will be repaired or replaced under warranty This notice explains the different types of pixel defects and defines acceptable defect evels for each type In order to qualify for repair or replacement under warranty the number of pixel defects on a TFT LCD panel must exceed hese acceptable levels For example no more han 0 000426 of the sub pixels on a 19 XGA monitor may be defective Furthermore Philips sets even higher quality standards for certain ypes or combinations of pixel defects that are more noticeable than others This policy is valid worldwide subpixel subpixel subpixel y iD Z Pixels and Sub pixels A pixel or picture element is composed of three sub pixels in the primary colors of red green and blue Many pixels together form an image When all sub pixels of a pixel are lit the three colored sub pixels together appear as a single white pixel When all are dark the three colored sub pixels together appear as a single black pixel Other combinations of lit and dark sub pixels appear as single pixels of other colors Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways There are two categories of pixel defects and several types of sub pixel defects within each category Bright Dot Defects Bright dot defects appear as pixels or sub pixels hat are always lit or on That is a bright dot is
34. nnot display this video mode Recommended resolution for Philips 19 1440x900 60Hz Unplug all cables then connect your PC to the monitor that you used previously In the Windows Start Menu select Settings Control Panel In the Control Panel Window select the Display icon Inside the Display Control Panel select the Settings tab Under the setting tab in box labeled desktop area move the sidebar to 1440x900 pixels 19 Open Advanced Properties and set the Refresh Rate to 60Hz then click OK Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1440x900 60Hz 19 Shut down your computer disconnect your old monitor and reconnect your Philips LCD monitor Turn on your monitor and then turn on your PC What does the recommended refresh rate for LCD monitor Recommended refresh rate in LCD monitors is 60Hz In case of any disturbance on screen you can set it up to 75Hz to see if that removes the disturbance Q3 Ans Q4 Ans Q5 Ans Q6 Ans 34 What are the inf and icm files on the CD ROM How do I install the drivers inf and icm These are the driver files for your monitor Follow the instructions in your user manual to install the drivers Your computer may ask you for monitor drivers inf and icm files or a driver disk when you first install your monitor Follow the instructions to insert the companion CD ROM included in this pac
35. ntrast EM What is it Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor s contrast ratio for maximum visual clarity and viewing enjoyment stepping up backlighting for clearer crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds EJ Why do I need it You want the very best visual clarity and viewing comfort for every type of content SmartContrast dynamically controls contrast and adjusts backlighting for clear crisp bright gaming and video images or displays clear readable text for office work By reducing your monitor s power consumption you save on energy costs and extend the lifetime of your monitor EJ How does it work When you activate SmartContrast it will analyse the content you are displaying in real time to adjust colors and control backlight intensity This function will dynamically enhance contrast for a great entertainment experience when viewing videos or playing games 3 3 Philips Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products We use some of the industry s most advanced manufacturing processes and practice stringent quality control However pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable No manufacturer can guarantee that all panels will be free from pixel defects but Philips guarantees hat any mo
36. oducts damaged by these modifications incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you This includes but is not limited to prerecorded material whether copyrighted or not copyrighted the model or production number on the product has been altered deleted removed or made illegible Where IS SERVICE AVAILABLE Warranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics In countries where Philips Consumer Electronics does not distribute the product the local Philips service organization will attempt to provide service although there may be a delay if the appropriate spare parts and technical manual s are not readily available Where CAN I GET MORE INFORMATION For more information contact the Philips Customer Care Center by calling 877 835 1838 U S A customers only or 919 573 7855 Before Requesting Service Please check your owner s manual before requesting service Adjustments of the controls discussed there may save you a service call TO GET WARRANTY SERVICE IN U S A PUERTO RICO OR US VIRGIN ISLANDS Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing Philips Customer Care Center 877 835 1838 or 919 573 7855 In U S A P
37. ou are not going to use it for an extensive period of time Unplug the monitor if you need to clean it with a slightly damp cloth The screen may be wiped with a dry cloth when the power is off However never use organic solvent such as alcohol or ammonia based liquids to clean your monitor To avoid the risk of shock or permanent damage to the set do not expose the monitor to dust rain water or excessive moisture environment f your monitor gets wet wipe it with dry cloth as soon as possible f foreign substance or water gets in your monitor please turn the power off immediately and disconnect the power cord Then remove the foreign substance or water and send it to the maintenance center Do not store or use the monitor in locations exposed to heat direct sunlight or extreme cold In order to maintain the best performance of your monitor and use it for a longer lifetime please use the monitor in a location that falls within the following temperature and humidity ranges o Temperature 0 40 C 32 95 F o Humidity 20 80 RH IMPORTANT Always activate a moving screen saver program when you leave your monitor unattended Always activate a periodic screen refresh application if your monitor will display unchanging static content Uninterrupted display of still or static images over an extended period may cause burn in also known as after imaging or ghost imaging on your screen Burn in
38. p 4 00pm 8 00pm 27 Israel Company Eastronics LTD Address 13 Rozanis St PO B 39300 Tel Aviv 61392 Israel Tel 1 800 567000 call free in Israel 972 50 8353722 after service hours until 20 00 Fax 972 3 6458759 E mail eastronics eastronics co il Service hours Sun Thurs 08 00 18 00 Your Philips First Choice Warranty USA Thank you for purchasing this Philips monitor All Philips monitors are designed and manufactured to high standards and deliver high quality performance ease of use and ease of installation Should you encounter any difficulties while installing or using this product please contact Philips directly to benefit from your Philips F1rst Choice Warranty his two year service warranty entitles you to a swap model on site within 48 hours of your call being received within the first year of purchase If you have any problems with your monitor within the second or third year of purchase we will repair it after it has been sent to the service provider at your expense and returned to you within five working days free of charge LIMITED WARRANTY Computer Monitor Click here to access the Warranty Registration Card Two Years Free Labor Two Years Free Service on Parts One Year Exchange Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year This product must be shipped in at your expense for service durin
39. plication being used Other cards installed Having the following information available will also help speed up the process Your proof of purchase indicating date of purchase dealer name model and product serial number e The full address to which the faulty monitor has to be collected and the swap model should be delivered Philips customer help desks are located worldwide Click here to access the F1rst Choice Contact Information Or you can reach us via Website http www philips com support First Choice Contact Information Telephone number ariff 3 0810 000206 78 250851 45 3525 8761 Luxembourg 26 84 30 00 Local call tariff ca 08 The Netherlands 31 0900 0400 063 Ca 40 7 2270 8250 0223491505 2 1359 1440 34 __ 902 888 785 call tariff call tariff all tarifi z z 6 08 632 0016 Switzerland 2 2310 2116 United Kingdom 207 949 0069 22 Your Guarantee in Central and Eastern Europe Dear Customer Thank you for purchasing this Philips product which has been designed and manufactured to he highest quality standards If unfortunately something should go wrong with this product Philips guarantees free of charge labor and replacement parts during a period of 24 months from date of purchase What is covered This Philips Guarantee in Central and Eastern Europe applies within Czech Republic Hungary Slovakia Slovenia Russia and T
40. ppines Thailand Turkey Ukraine Vietnam m astern Europe ELARUS Technic al Center of JV IBA Bogdanovich str 155 BY 220040 Minsk Tel 375 17 217 33 86 w BELARUS Service BY Petrus Brovky st 19 101 B 220072 Minsk Belarus BULGARIA LAN Service 140 Mimi Balkanska Str Office center Translog 1540 Sofia Bulgaria Tel 4 359 2 960 2360 www lan service bg CZECH REPUBLIC General Consumer Information Center 800 142100 Xpectrum Lu n 591 4 CZ 160 00 Praha 6 Tel 800 100 697 or 220 121 435 Email info xpectrum cz www xpectrum cZ CROATIA Renoprom d o o Ljubljanska 4 Sv Nedjelja 10431 Croatia Tel 385 1 333 0974 ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE 12618 Tallinn Tel 372 6519900 www ee invia fujitsu com HUNGARY Serware Szerviz Vizimoln r u 2 4 HU 1031 Budapest Tel 36 1 2426331 Email inbox serware hu www serware hu HUNGARY Profi Service Center Ltd 123 Kulso Vaci Street 1044 Budapest Europe Center ungary Tel 36 1 814 8080 m andras psc hu LATVIA ServiceNet LV Jelgavas iela 36 LV 1055 Riga Tel 371 7460399 Email servissQservicenet lv LITHUANIA ServiceNet LT Gaiziunu G 3 LT 3009 KAUNAS Tel 370 7400088 Email servisas servicenet lt www servicenet lt ROMANIA Blue Ridge Int l Computers SRL 115 Mihai Eminescu St Sector 2 RO 020074 Bucharest Tel 40 21
41. rn in also known as after imaging or ghost imaging on your screen Burn in after imaging or ghost imaging is a well known phenomenon in LCD panel technology In most cases the burned in or after imaging or ghost imaging will disappear gradually over a period of time after the power has been switched off Always activate a moving screen saver program when you leave your monitor unattended Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content Severe burn in or after image or ghost image symptoms will not disappear and cannot be repaired The damage mentioned above is not covered under your warranty Image appears distorted Text is fuzzy or blurred Set the PC s display resolution to the same mode as monitor s recommended screen native resolution Green red blue dark and white dots appears on the screen e The remaining dots are normal characteristic of the liquid crystal used in today s technology Please refer the pixel policy for more detail The power on light is too strong and is disturbing You can adjust power on light using the power LED Setup in OSD main Controls For further assistance refer to the Consumer Information Centers list and contact Philips customer service representative 33 7 2 General FAQs Q1 Ans Q2 Ans When I install my monitor what should I do if the screen shows Ca
42. se 1440x900 60Hz for best results please follow the instructions below to avoid damage or injury Before you start disassembling the monitor base Display of the native resolution alert can be switched off from Setup in the OSD On Screen Display menu 1 Place the monitor face on a safe surface push down on the release button and pull the base stand away from the monitor body EX Physical Function Tilt 3 Product information 3 1 Smartlmage Lite EB What is it Smartlmage Lite provides presets that optimize display for different types of content dynamically adjusting brightness contrast color and sharpness in real time Whether you re working with text applications displaying images or watching a video Philips Smartlmage Lite delivers great optimized monitor performance EJ Why do I need it You want a monitor that delivers optimized display all your favorite types of content Smartlmage Lite software dynamically adjust brightness contrast color and sharpness in real time to enhance your monitor viewing experience EJ How does it work Smartlmage Lite is an exclusive leading edge Philips technology that analyzes the content displayed on your screen Based on a scenario you select Smartlmage Lite dynamically enhances the contrast color saturation and sharpness of images to enhance the contents being displayed all in real time with the press of a single button EJ How to
43. uerto Rico and U S Virgin Islands all implied warranties including implied warranties of merchantability and fitness for a particular purpose are limited in duration to the duration of this express warranty But because some states do not allow limitations on how long an implied warranty may last this limitation may not apply to you TO GET WARRANTY SERVICE IN CANADA Please contact Philips at 800 479 6696 Two years free parts and two years free labor will be provided at Philips Canada depot or any one of its authorized service centers In Canada this warranty is given in lieu of all other warranties No other warranties are expressed or implied including any implied warranties of merchantability or fitness for a particular purpose Philips is not liable under any circumstances for any direct indirect special incidental or consequential damages howsoever incurred even if notified of he possibility of such damages REMEMBER Please record the model and serial numbers found on the product below ODEL SERIAL This warranty gives you specific legal rights You may have other rights which vary from state province to state province Before contacting Philips please prepare the following details so we can solve your problem quickly Philips ty Philips se Purchase required PC enviro e number ial number date copy of purchase may be D ri nment Processor o CUP and Gr
44. urkey and only for monitors originally designed manufactured approved and or authorized for usage within these countries Warranty coverage begins as from the day you buy your monitor For 2 years thereafter your monitor will be serviced in case of defects provided for under the warranty coverage What is excluded The Philips guarantee applies provided the product is handled properly for its intended use in accordance with its operating instructions and upon presentation of the original invoice or cash receipt indicating the date of purchase dealer s name and model and production number of the product The Philips guarantee may not apply if the documents have been altered in any way or made illegible e the model or production number on the product has been altered deleted removed or made illegible repairs or product modifications and Iterations have been executed by unauthorized service organizations or persons e damage is caused by accidents including but not limited to lightning water or fire misuse or neglect Reception problems caused by signal conditions or cable or antenna systems outside the unit Defects caused by abuse or misuse of the monitor e Product requires modification or adaptation to enable it to comply with local or national technical standards which apply in countries for which the product was not originally designed manufactured approved and or authorized Therefore a
45. uth Korea Company PCS One Korea Ltd Address 112 2 Banpo dong Seocho ku Seoul 137 040 Korea Call Center Tel 080 600 6600 Tel 82 2 591 1528 Fax 82 2 595 9688 E mail cic_korea philips com Service hours Mon Fri 9 00AM 6 00PM Sat 9 00AM 1 00PM Malaysia Company After Market Solutions CE Sdn Bhd Address Lot 6 Jalan 225 51A 46100 Petaling Jaya Selangor DE Malaysia Phone 603 7953 3370 Philips Info Line 1 800 880 180 Fax 603 7953 3338 E mail pceinfo my philips com Service Hours Mon Fri 8 15am 5 1 5pm Sat 9 00am 1 00pm 1 Pakistan Philips Consumer Service Address Mubarak manzil 39 Garden Road Saddar Karachi 4400 Tel 9221 2737411 16 Fax 9221 2721167 E mail care philips com Website www philips com p 26 Singapore Company Philips Electronics Singapore Pte Ltd Philips Consumer Care Center Address 620A Lorong 1 Toa Payoh TP4 Building Level 1 Singapore 319762 Tel 65 6882 3999 Fax 65 62508037 E mail consumencare sg philips com Service hours Mon Fri 9 00am 6 00pm Sat 9 00am 1 00pm Taiwan Company FETEC CO Address 3F No 6 Lane 205 Sec 1 Chang Hsing Rd Lu Chu Hs Taoyuan Taiwan R O C 33800 Consumer Care 0800 231 099 Tel 03 2120336 Fax 03 3129184 E mail knlinO8 xuite net Service hours Mon Fri 8 30am 7 00pm Thailand Company Axis Computer System Co Ltd Address 1421 Soi Lardprao 94 Srivara Town In Town So
46. weden Switzerland Spain and the United Kingdom and only for monitors originally designed manufactured approved and or authorized for usage within these countries Warranty coverage begins as from the day you buy your monitor For two years thereafter your monitor will be swapped by at least an equivalent monitor in case of defects provided for under the warranty coverage The swap monitor remains yours and Philips keeps the defective original monitor For the swap monitor the warranty period remains equal to that of your original monitor being 24 months as from the purchase date of your original monitor 20 What is excluded The Philips First Choice Warranty applies provided the product is handled properly for its intended use in accordance with its operating instructions and upon presentation of the original invoice or cash receipt indicating the date of purchase dealer s name and mode production number of the product and The Philips First Choice Warranty may not apply if The documents have been altered in any way or made illegible The model or production number on the product has been altered deleted removed or made illegible e Repairs or product modifications and alterations have been executed by unauthorized service organizations or persons Damage is caused by accidents including but not limited to lightning water or fire misuse or neglect e Reception problems caused by sig
47. your computer system Caution This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data O Warning This icon indicates the potential for bodily harm and tells you how to avoid the problem Some warnings may appear in alternate formats and may not be accompanied by an icon In such cases the specific presentation of the warning is mandated by the relevant regulatory authority 1 3 Disposal of product and packing material Waste Electrical and Electronic Equipment WEEE This marking on the product or on its packaging illustrates that under European Directive 2002 96 EC governing used electrical and electronic appliances this product may not be disposed of with normal household waste You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection To determine the locations for dropping off such waste electrical and electronic contact your local government office he waste disposal organization that serves your household or the store at which you purchased he product Your new monitor contains materials that can be recycled and reused Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of All redundant packing material has been omitted We have done our utmost to make the packaging easily separable into mono materials
Download Pdf Manuals
Related Search