Liebherr IKP 1554 Premium
Contents
1. cover Unscrew the hinge O and remove the compartment door with the hinge e Unscrew the closure e Close the holes with the plugs e Rotate the door and closure by 180 and replace on the other side Insert the compartment door at the top put the hinge in place at the bottom screw down again and close the cover Installation information e This appliance can also be used to replace an existing appliance In this case remove the hinges on the unit door and in the recess They are no longer needed as the unit door is fitted to the appliance door e Fig B Align the unit with a spirit level and an angle If necessary level out by building up from underneath The shelf and side walls of the unit must be at right angles to one another e Fitthe refrigerator freezer in stable kitchen units only e The following ventilation gaps must be observed The depth of the ventilation channel at the rear of the unit must be at least 38 mm There must be a ventilation space of at least 200 cm underneath and at the top of the unit the greater the area the more economically the appliance will run e Check installation dimensions in accordance with fig B Appliance height a recess height b Connecting to the mains Power supply AC and voltage at the operating point must comply with the details on the type plate It is located inside the appliance on the left hand side e The appliance must be connected with a properl2. of the counter nuts 62 fig G Fig H Suspend the strut with the fitting aids 69 on the inside of the unit door and align centrally draw a short line in the middle of the unit door align the arrow on the strut with it keeping the same distance to outer edges on left and right Fasten the attachment strut 6 in the centre Fig H with at least 6 screws if the doors are made of wood board with 4 screws round the edge in the case of panel doors Lift the fitting aids 69 out to the top turn round and insert into the adjacent openings e Fig J Suspend the unit door on the door of the appliance adjusting pins do Screw the counternuts 62 loosely onto the adjusting pins Close the door e Fig J1 Check the gap between the door and the surround ing unit doors Fig J2 Align the unit door flush with the surrounding unit fronts align laterally X by sliding in the corresponding direction adjust height Y and lateral tilt with the adjusting pins 63 using a screwdriver Tighten counternuts 62 e Fig K Secure the mounting bracket 6 to the pre drilled holes in the appliance door using the hexagonal screw 7 e Screw the appliance door onto the unit door with the at tachment brackets 0 Ensure that both metal edges are flush symbol Drill at tachment holes making a hole with a bradawl and screw tight e Adjust the depth of the unit door Z Fig J2 top loosen screws 64 Fig K bottom loosen the
3. Installation instructions GB for refrigerators BioFresh appliances freezers for integrated use with door on door system 7082 452 01 IK IKP IKB IG 2406 AD Torx 925 5 8 amg 2x M5 x 22 12x 94x 14 6x mn hm R z 2x 19 mm 1x 1x 1x Installation instructions Keep the installation instructions in a safe place and pass them on to the next owner of your appliance where applica ble The operating instructions apply to several models Differences may therefore occur Before reading please fold out and refer to the illustrated front page You additionally require the following tool for installation Cordless screwdriver Torx 15 20 25 spanner 13 Changing over door hinges Fig A1 The door hinges can be changed from one side to the other if need be Otherwise continue from Installation information fig B e To simplify installation slide the appliance three quarters of the way into the recess Open the door For models with soft stop proceed according to fig A otherwise continue according to fig A1 For appliances 870 mm high remove the lower storage rack for easier installation e Fig A Detach the soft stop mechanism Please note the soft stop mechanism contracts in the detached state e Take hold of cover at the back for removal bend it downwards a little and push it away to the side e Undo screw while pressing the fork of the soft stop mechanism dow
4. hexagonal screws with the ring spanner 3 provided and adjust the door Fig J1 Allow an air gap of approx 2 mm between the unit door and the body of the unit Do not allow knobs and seal ing lips to make contact with the appliance as this can have a detrimental effect on its function e Fig L If the unit door is large or divided into separate parts attach another pair of attachment brackets accessories bag fig C3 Use the pre drilled holes in the handle area of the appliance door e Check that the door is properly positioned and readjust if necessary Tighten all screws Fig L1 Tighten the counternuts 62 with the ring span ner 3 provided holding the adjusting pins 63 in position with a screwdriver e Fig L2 If necessary align the equaliser trim parallel with the floor of the unit It must not project e Fig L3 Fix the appliance in the round hole at the bottom with the second screw 9 through the plastic bracket e Fig M Fit all the covers Place the top cover 9 in position and click into place Place lateral cover 6 in position slide it to the limit then press on the cover until it audibly engages Slide on cover 3 laterally draw the cover forwards using a screwdriver according to fig M so that it engages well into place e Fig N The opening resilience of the door can now be adjusted Adjust using the no 5 Allen key provided Turn clockwise for stronger resilience Tur
5. n anticlockwise for weaker resilience factory setting The manufacturer works constantly on the further develop ment of all the types and models Therefore please under stand that we have to reserve the right to make design equip ment and technical modifications IK IKP IKB IG
6. nwards so that it cannot suddenly disen gage e Carefully disengage the fork of the soft stop mechanism from the hinge the mechanism contracts e Unscrew the ball stud together with the soft stop mechanism from the door and set it aside e Fig A1 lift off cover parts and D in a forward direction using a flat blade screwdriver e Detail fig A1 1 Loosen the attachment screws on the top and bottom of the body of the appliance Pull the door outwards and remove e Transfer the attachment screws to the other side and screw in a little way e Fig A1 Unscrew the door attachment screws and replace the hinges in the diagonally opposite corner NB Do not fold the hinges together danger of injury Use a cordless screwdriver to screw down the hinges the screws are self tapping e Close the holes on the other side with the plugs 9 e Suspend the appliance door in the ready inserted screws 8 and tighten screws e Fig A Fit the soft stop mechanism back in place Screw ball stud together with soft stop mechanism into the new fastening hole e Draw the fork out of the soft stop mechanism put it over the hinge and attach with the stud e Re fasten with screw while pressing the fork onto the hinge so that it does not disengage e Fit all the cover parts back in place IK IKP IKB IG Depending on model and options Changing the compartment door e Fig A2 At the hinge fold away the
7. of the unit walls note the additional space needed for units with door furniture knobs sealing lips etc Allow the hinges to protrude by the additional distance required Press the appliance on the hinge side against the wall of the unit Fig E3 Level the appliance by adjusting the adjustable feet with the spanner provided 3 Align the body of the appliance parallel to the front edges of the side walls of the unit Screw plastic bracket amp onto the handle side of the appli ance with M5 screws 7 Make sure the front of the plastic bracket 9 is flush with the front edge of the floor of the unit Do not forget the additional space required if the unit has door furniture knobs sealing lips etc and align parallel to the front edge of the hinge Fig F Screw the appliance into the recess Figs F1 2 Screw in with long wood board screws 3 through the hinge plates at the top and bottom Fig F3 Screw in temporarily with a long screw 3 through the middle of the long slot on the plastic bracket 9 Fold up the cover on the plastic bracket and close the appliance door Fitting the unit door Fig G1 Check the 8 mm default setting distance between appliance door and bottom edge of attachment strut Fig G Slide the fitting aids 6 up level with the unit door underside of stop edge A of fitting aid upper edge of unit door Fit the attachment strut 63 on the unit door For this purpose unscrew the strut by way
8. y in stalled fused socket e The fuse of the plug has to be 10 A or more it must be situated away from the rear area of the appliance and be easily accessible e Do not connect to stand alone inverters operate with so called energy saving plugs this can damage the electronic system connect together with other appliances using an exten sion cable danger of overheating e When removing the mains cable from the back of the appliance remove the cable holder to prevent vibration noise Installation instructions Installation and fitting Figs C1 3 All installation components are supplied Fig D Fit equaliser trim centered on the appliance slide into the channel and engage in the key holes Route the mains cable with the aid of string in such a way that the appliance can be easily connected after installation Slide the appliance three quarters of the way into the recess Note the thickness of the unit walls For 16 mm unit wall 568 mm recess Fig D Stick sealing strip 9 onto the side of the appliance on the handle side flush with the front remove the protec tive film and stick on shorten to recess height if necessary Clip spacers 3 and 5 onto the hinges Fig E Slide appliance into the recess until the spacers make contact with the side of the units Fig E1 For 19 mm unit wall 562 mm recess Fig E2 Slide the appliance into the recess until the fronts of the hinges are flush with the sides
Download Pdf Manuals
Related Search