Siemens SN26N291EU
Contents
1. 24 Electrical connection Connect the appliance to an alternating current only ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correcily installed socket with protective earth conductor See rating plate for reguired fusing 131 The socket must be near the appliance and freely accessible following installation The connection may be modified by technicians only A power cord extension may be purchased from customer service only Use only a residual current operated circuit breaker which features the symbol EX Only this extension guarantees compliance with the currently valid regulations The appliance features a water damage protection system Please note the system will not function unless the power supply is connected Removing the appliance Also observe the sequence of worksteps here Disconnect the appliance from the power supply Turn off the water supply Disconnect the waste water and fresh water connections Loosen the fastening screws under the worktop If fitted remove the base panel Pull out the appliance carefully pulling the hose behind Transportation Empty the dishwasher and secure loose parts Drain the appliance according to the following steps Turn on the tap Close the door Switch on ON OFF switch 1 1 The displays of the last selecte2. Remove any residue and clean filters under running water Re install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system 17 en Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 122 18 and 241 Check outlet nozzles on the spray arms for blockages Unscrew the upper spray arm 22 Remove the lower spray arm 24 upwards Clean spray arms under running water Re engage or screw on spray arms Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump The rinsing water is then not pumped out and covers the filter In this case First disconnect the appliance from the power supply Remove the filters 26 Scoop out water use a sponge if reguired Using a spoon prise off pump cover as illustrated until it clicks then grip the cover by the lug and first pull it upwards until it resists and then pull it out forwards Check inner compartment and remove any foreign objects Place cover in the original position press down and engage Install filters Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user This
3. sani retail GANNA y en Operating instructions SIEMENS Reset 3 sec h Hi T A 1 S i N l l l l l l l l 1 AAR SES SPSS N NIINIIN NJ N N NJ N N en Table of contents Safety instructions 4 Delivery s sie Ake an an oat ees 4 Installation s s ve eee ee ee 4 In daily use 4 Children in the household 4 DOOKIOCK sni Pen naa nga 4 Buton lock riasan ee yea ve es 5 Damage binasa yn na Goes 5 DISPOSAl ised eta oe dae eee e 5 Getting to know your appliance 5 Control panel 5 Appliance interior 5 Water softening system 6 SOWING os hw dh sie ha No RE ARSA 6 Water hardness table 6 Special salt 7 Using special salt 7 Detergents with salt component 7 Switching off water softening system 7 Ri se aid sis san ana nan 8 Setting amount of rinse aid 8 Switching off rinse aid refill indicator 8 Utensils Woo oo oo co Woo mo oi 9 Not suitable 9 Glass and utensil damage 9 Loading the dishwasher 9 Unloading the dishwasher 9 Cups and glasses 9 PANS Sen Wits fe hse ete nly bacon 10 Cutlery drawer 10 Folding spikes
4. 10 Cup support clip 11 Small accessories holder 11 Detergent 12 Adding detergent 12 Combination detergent 13 Overview of programmes 14 Programme selection 14 Information about comparability tests 14 Additional options 15 Express Wash 15 Half NOAH eth eee pase anna Da 15 Hygi eti ji ek am ee Raa ee 15 Intensive zone 15 Extra dryINGg ma anna antara 15 Washing the dishes 15 Programme data 15 Agua sensor 15 Switching on the appliance 15 Programme seguence indicator 15 Remaining running time display 16 Timer programming 16 End of programme 16 Switching off the appliance 16 Interrupting the programme 16 Terminating the programme 16 Changing the programme 16 Maintenance and care 17 Overall condition of the machine 17 Special salt and rinse aid 17 KIE a Me oc ba pm ena 17 Spray arMS 18 Waste water pumP 18 Troubleshooting 19 when the appliance is switched on 19 Changing settings 19 on the appliance 19 during the wash cycle 20 on the utensils 20 Customer service 21
5. during the wash cycle Unusual foam formation Handwash liquid in the rinse aid dispenser Spilled rinse aid causes excessive frothing therefore please remove with a cloth Appliance stops during the wash cycle Power supply interrupted Water supply interrupted Filling valves making striking noises Caused by the installation of the water line and has no effect on the function of the machine Remedial action is not possible Knocking rattling noise during rinsing Spray arm is striking utensils Utensils not arranged correctly 20 on the utensils Food residue on the utensils Utensils placed too closely together utensils basket overfilled Too little detergent Rinse programme too weak Spray arm rotation obstructed Spray arm nozzles blocked Filters blocked Filters incorrectly inserted Waste water pump blocked Top basket on right and left not set to same height Tea or lipstick residue is not completely removed The detergent has an inadequate bleaching effect Too low rinsing temperature Too little unsuitable detergent White stains on the utensils glasses remain milky If phosphate free detergents are used with hard tap water white deposits may be deposited more easily on utensils and the container walls Too little unsuitable detergent Too weak programme selected No too little rinse aid No too little special salt
6. If the detergent dispenser 29 is still closed press the lock 80 to open the detergent dispenser Pour detergent into the dry detergent dispenser 29 only insert tablet flat not on its edge Dosage see manufacturer s instructions on the packaging The graduated detergent dispenser 29 helps you add the correct amount of powder or liguid detergent Usually 20 ml 25 ml are adequate for normal soiling If using tablets one tablet is adeguate Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty The detergent dispenser opens automatically at the optimum time depending on the programme The powder or liguid detergent is distributed in the appliance and is dissolved the tablet falls into the tablet collecting tray where it dissolves in doses Tip If the utensils are only lightly soiled slightly less than the indicated amount of detergent is usually adequate Suitable detergents and care products can be purchased online via our website or via customer service see back page Combination detergent Apart from conventional detergents Solo a number of products are offered with additional functions These products contain not only the detergent but also rinse aid and salt replacement substances 3in1 and depending on the combination 4in1 5in1 etc additional components such as glass protection or stainless s
7. Water softening system set to the wrong value Salt dispenser lock not fastened Contact the detergent manufacturer in particular if the utensils are very wet at the end of the programme limescale forms Dull discoloured glasses film cannot be washed off Unsuitable detergent Glasses not dishwasher proof Streaks on glasses and cutlery glasses have metallic appearance Too much rinse aid Plastic parts discoloured Too little unsuitable detergent Too weak programme selected Rust spots on the cutlery Cutlery not rust resistant Salt content in the rinsing water too high as salt dispenser lock not fastened firmly or salt was spilled while being refilled Utensils not dry Appliance door opened too early and utensils taken out too early Programme selected without drying Too little unsuitable rinse aid The combined detergent used has a poor drying performance Use rinse aid see Rinse aid chapter for setting en Customer service If the advice given does not resolve your problem please contact your customer service Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list When calling please guote the appliance number 1 and the production date FD lt 2 which can be found on the rating plate 131 on the appliance door NO Rely on the expertise of the manufactur
8. Installation 22 Safety instructions 22 Delivery s sita aii Mada 22 Technical specifications 23 Installation 23 Waste water connection 23 Fresh water connection 23 Warm water connection 24 Electrical connection 24 Removing the appliance 24 Transportation 25 Protection against frost Emptying the appliance 25 Waste disposal 25 PACKAGING ai Bi uht ne nga mag 25 Old appliances 25 en Safety instructions Delivery Check the packaging and dishwasher immediately for damage caused in transit Do not switch on a damaged appliance but contact your supplier Please dispose of the packaging material in an environmentally friendly manner Do not let children play with packaging and its parts There is a risk of suffocation from collapsible boxes and film Installation Read the Installation chapter to learn how to install and connect the appliance correcily In daily use Use the dishwasher only in the household and only for its designed purpose for washing domestic dishes Children or people whose physical sensory or mental abilities prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person Do not lean or sit on the open door The ap
9. Level the appliance with the aid of the height adjustable feet Ensure that the appliance is situated securely on the floor A builtunder or integrated appliance which is installed subsequently as a free standing appliance must be secured to prevent it from overturning e g by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards The appliance can easily be installed in a fitted kitchen between wooden and plastic walls If the plug is not freely accessible an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions en Waste water connection The required work sequence can be found in the installation instructions If required fit a siphon with an drainage connection Connect the waste water hose to the drainage connection of the siphon with the enclosed parts Ensure that the drainage hose is not kinked crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out Fresh water connection Connect the fresh water connection to the tap according to the installation instructions with the enclosed parts Ensure that the fresh water connection is not kinked crushed or twisted When replacing the appliance always use a new water supply hose Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar
10. At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature cold water hot water max temperature 60 C 23 en Warm water connection The dishwasher can be connected to cold or hot water up to max 60 C Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation e g solar heating system with circulation line This will save energy and time The hot water setting d i allows you to adjust your appliance optimally to operation with hot water It is recommended to have a water temperature temperature of the incoming water of at least 40 C and no more than 60 C It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler seting hot water Close the door Switch on ON OFF switch C11 Hold down programme button A and press START button 9 until 4 0 is indicated on the digital display Release both buttons The LED for button LA flashes and the digital display 14 displays the factory setting H i 4 Press programme button LA until the factory set value d 0 is indicated on the digital display 11 To change the setting By pressing the C button you can switch the hot water setting off o 00 or on diti 1 Press START button 9 The set value is saved
11. Please follow the safety instructions under Disposal of your appliance This appliance is identified K according to the European guideline 2002 96 EC on waste electrical and electronic eguipment WEEE The guideline specifies the framework for an EU wide valid return and re use of old appliances Subject to changes 25 Childproof lock door lock 42 40 Activate the childproof lock Always close the appliance door completely 41 Open the door with activated when you leave the appliance childproof lock This is the only way you can protect your 42 Deactivate childproof lock children from potential dangers Baking sheet spray head H H in a gourmet plates pasta plates dinner plates can be cleaned with the aid of the spray head To do this remove the top basket and insert the spray head as illustrated in the diagram To ensure that the spray jet can reach all parts arrange the baking sheets as illustrated max 4 baking sheets and 2 grilles Never operate the dishwasher without the top basket or baking sheet spray head some models AGUA STOP guarantee en does not apply to appliances without Agua Stop In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions 1 If ou
12. ensures that the appliance is guickly available for use again The following overview will help you locating the causes and gives helpful advise to eliminate them A Warning If on the digital display 11 an error code E 1 to E 30 always disconnect the appliance from the power supply and then turn off the tap You can rectify certain faults yourself see following fault description for all other faults please contact customer service and state the indicated fault XX A Warning Don t forget Repairs may be carried out by technicians only If a component has to be replaced ensure that only original spare parts are used Improper repairs or use of non original spare parts may cause considerable damage and put the user at considerable risk when the appliance is switched on The appliance does not start The mains fuse has tripped The appliance plug has not been inserted The appliance door has not been shut properly changing settings A setting cannot be changed a programme starts Wrong programme button pressed Terminate the programme see chapter entitled Terminating the programme Reset and start all over again You did not wait until programme ended en on the appliance Lower spray arm rotates sluggishly Spray arm blocked The door is difficult to open Child proof lock is activated The deactivation instructions are at the back in th
13. out and does not corrode the rinsing tank Open the Pe cap of the compartment 125 Fill the tank with water only required when switching on the appliance for the first time Then add dishwasher salt not table salt or tablets The water is displaced and runs out As soon as the salt refill indicator 4 on the fascia is lit top up the salt depending on model en Using detergents with salt component If combined detergents with a salt component are used salt can usually be omitted up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l If the water hardness is over 21 dH special salt must be used Switching off salt refill indicator water softening system If the salt refill indicator 4 is impaired e g when using combined detergents containing salt component it can be switched off Proceed as described under Adjusting the water softening system and set the value to H3 The water softening system and salt refill indicator are now switched off A Warnings Never fill the salt dispenser with detergent You will destroy the water softening system To prevent corrosion always refill with salt immediately before switching on the appliance en Rinse aid As soon as the rinse aid refill indicator is lit on the fascia there is still a rinse aid reserve of 1 2 rinsing processes Refill with rinse aid The rinse ai
14. selection You can select a suitable programme according to the type of utensils and degree of soiling 14 Information about comparability tests The conditions for th e comparison test are available on request by e mail from dishwasher test appliances com Quote the appliance number E Nr and the production date FD which you can find on the rating plate appliance door 31 on the Additional options depending on model Additional options can be set with the buttons 8 G Express Wash The gt gt Express Wash lt lt function can reduce the running time by approx 20 to 50 depending on the selected rinse programme The change in the runnin time is indicated on the digital display 11 To obtain optimum cleaning results at a reduced running time water and energy consumption are increased Half load If you have only a few items to wash e g glasses cups plates you can switch to half load This will save water energy and time It is recommended to put a little less detergent in the detergent dispenser than for a full load Hygiene The temperature is increased during the cleaning process This increases the hygiene status This additional option is ideal for cleaning e g chopping boards and baby bottles Intensive zone Perfect for a mixed load You can wash very soiled pots and pans in the lower basket together with normally soile
15. OFF switch 1 1 Turn off the tap not applicable if Agua Stop fitted Remove the utensils when they have cooled down 16 A Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher Any escaping water vapour could damage sensitive worktops Interrupting the programme Switch off ON OFF switch 1 The LEDs go out The programme is saved If the door was opened on an appliance which has a warm water connection or is heated first leave the door ajar for several minutes and then close Otherwise expansion pressure may cause the appliance door to spring open or water to run out of the appliance To continue the programme switch on the ON OFF switch again Terminating the programme nesel Press START button 9 for approx 3 sec The numerical display L11 indicates 2 7 The programme seguence lasts approx 1 min On the digital display 11 is indicated Luwu Switch off ON OFF switch 1 Changing the programme When the START button 9 has been pressed the programme cannot be changed The only way a programme can be changed is by Cancel programme Reset Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults This saves time and prevents problems Overall condition of the machine Check spray a
16. ch have been screwed to adjacent cupboards to ensure stability Do not install the appliance near heat sources radiators heat storage tanks cookers or other appliances which generate heat and do not install under a hob After installing the appliance ensure that the plug is easily accessible Some models The plastic housing on the water connection contains an electric valve the connecting cables are in the supply hose Do not cut through this hose do not immerse the plastic housing in water A Warning If the appliance is not in a cavity and a side panel is accessible the door hinge area must be covered at the side for reasons of safety risk of injury The covers are available as optional accessories from customer service or specialist outlets Delivery Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order This may cause small water stains These will disappear after the first wash cycle Technical specifications Weight max 60 kg Voltage 220 240 V 50 Hz or 60 Hz Connected load 1 9 2 3 kW Fuse 10 16 A Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature cold water hot water max temperature 60 C Installation The required installation dimensions can be found in the installation instructions
17. d programme light up Select programme with the highest temperature The expected programme duration is indicated on the numerical display 111 Press START button 9 Programme seguence starts After approx 4 minutes press the START button 9 until 2 2 i is indicated on the digital display After approx 1 min 2 05 is indicated on the digital display Switch the appliance off 1 the tap off Transport appliance upright only This prevents residual water from running into the machine control and damaging the programme seguence and turn Protection against frost If the appliance is in a room where there is a risk of frost e g holiday home empty the appliance completely see Transportation Turn off the tap disconnect supply hose and drain water en Waste disposal Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials Please dispose of the individual parts separated according to type Please ask your dealer or inguire at your local authority about current means of disposal Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations e g gt PS lt polystyrene Therefore plastic waste can be sorted out when the appliance is being disposed of Please follow the safety instructions under Delivery Old appliances
18. d utensils in the upper basket The spray pressure in the lower basket is intensified the rinsing temperature is increased slightly Extra drying An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better There is a slight increase in the energy consumption en Washing the dishes Programme data The programme data consumption values can be found in the summary of instructions They refer to normal conditions and the water hardness set value H 74 Different influencing factors such as e g water temperature or line pressure may result in deviations Aqua sensor depending on model The Aqua sensor is an optical measuring device light barrier which measures the turbidity of the rinsing water The Aqua sensor is used according to the programme If the Aqua sensor is active clean rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3 6 litres If the turbidity is greater the water is drained and is replaced with fresh water In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling Switching on the appliance Turn on the tap fully Switch on ON OFF switch L 1 The display of the last selected programme flashes This programme remains selected if no other programme button 2 lis pressed The expected programme duration flashes on the digital di
19. d is required for stain free utensils and clear glasses Use only rinse aid for domestic dishwashers Combined detergents with rinse aid component may be used up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l only If the water hardness is over 21 dH rinse aid must be used Open the dispenser 28 by pressing and lifting the plate on the cover Carefully pour rinse aid up to the max mark in the filler opening Close cover until it clicks shut To prevent excessive foam formation during the next rinse cycle remove any rinse aid which has run over with a cloth Setting amount of rinse aid The amount of rinse aid dispensed can be set from rd to r Z6 This is the factory setting 35 Do not change the amount of rinse aid unless streaks select lower setting or water stains select higher setting are left on the utensils Close the door Switch on ON OFF switch 1 Hold down programme button LA and press START button 9 until 4 77 is indicated on the digital display Release both buttons The LED for button A flashes and the digital display 11 displays the factory setting H 74 Press programme button until the factory set value 2 5 is indicated on the digital display 11 To change the setting Press programme button LC Each time the button is pressed the set value increases by one level when the val
20. e envelope depending on model Door cannot be closed Door lock has been activated To reset close the door with greater force Cover on the detergent dispenser cannot be closed Detergent dispenser overfilled or mechanism blocked by sticky detergent residue Detergent residue in the detergent dispenser Dispenser was damp when filled Check water supply display 3 lights up Tap turned off Water supply interrupted Supply hose kinked Filter in the water supply blocked Switch off the appliance and pull out the mains plug Turn off the tap Clean filter in the supply hose Reconnect power supply Turn on the tap Switch on the appliance 19 en Water is left in the appliance at the end of the programme E 24 Waste water hose is blocked or kinked Filters blocked amp 25 Waste water pump blocked cover on the waste water pump is not locked in position see Maintenance and care Filters blocked The programme has not yet ended Wait until programme ends digital display indicates 7 39 or implement the Reset function Refill indicator for salt 4 and or rinse aid 5 is not lit Refill indicator s switched off Adequate salt rinse aid available Refill indicator for special salt is lit No salt Refill with special salt Sensor does not detect salt tablets Use different special salt
21. egree of hardness of your tap water see table Setting The amount of salt dispensed can be set from 4 00 to 4 07 Salt is not required at the set value H 72 Find out about the hardness value of your tap water Your water utility company will help you with this Set value can be found in the water hardness table Close the door Switch on ON OFF switch C11 Hold down programme button LA and press START button 9 until 4 2 is indicated on the digital display Release both buttons The LED for button A flashes and the digital display 11 displays the factory setting H i 4 To change the setting Press programme button C Each time the button is pressed the set value increases by one level when the value of H 7 has been reached the display jumps back to H 5G off Press START button 9 The chosen setting has now been stored Water Hard hardness range value Clarke 0 8 so 9 10 s0 11 12 med E 3 15 med 16 20 med 21 26 27 38 39 62 Water hardness table ess mmol l ft 0 1 1 ft 1 2 1 4 jum 1a jum 92 un Pa hard 3 0 3 7 hard 3 8 5 4 hard 5 5 8 9 Set value on the machine Special salt Using special salt Always refill with special salt immediately before switching on the appliance This ensures that overrun special salt solution is immediately washed
22. er Call us to ensure that the repair will be carried out by fully trained service engineers who are eguipped with original spare parts for your appliance 21 en Installation The dishwasher must be connected correctly otherwise it will not function properly The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the reguired criteria as specified in the following paragraphs or in the installation instructions Install the appliance in the correct seguence Checking appliance on delivery Installing the appliance Waste water connection Fresh water connection Electrical connection Safety instructions Install and connect the appliance according to the installation and assembly instructions Prior to installation disconnect the dishwasher from the power supply Ensure that the protective conductor system of the domestic supply has been correctly installed The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 131 If the power cord of this appliance is damaged it must be replaced with a particular power cord To prevent injury the power cord may be replaced by customer service only If the dishwasher is installed in a high sided unit the unit must be secured properly 22 Install buil under or integratable appliances only under continuous worktops whi
23. me ends en Loading the dishwasher Remove large food remnants It is not necessary to prerinse utensils under running water Place the utensils so that they are secure and cannot tip over all utensils with their openings face down parts with curves or indentations are at an angle thereby allowing water to drain does not obstruct rotation of the two spray arms 22 and 1241 Very small utensils should not be washed in the machine as they may fall out of the baskets Unloading the dishwasher To prevent water from dripping off the upper basket onto the utensils in the lower basket it is recommended to empty the appliance from the bottom up Hot utensils are sensitive to shock Therefore when the programme ends leave the utensils to cool down in the dishwasher until they can be handled Cups and glasses Top basket 21 en Pans Bottom basket 127 Tip Heavily soiled utensils pans should be placed in the bottom basket The more powerful spray jet provides a better dishwashing result Tip Other examples such as the best way of loading your dishwasher can be found on our homepage as a free download The corresponding Internet address can be found on the back page of these instructions for use 10 Cutlery drawer Arrange the cutlery in the cutlery drawer as illustrated Separately ar
24. ock door lock The description of the childproof lock is at the back in the envelope depending on model Childproof lock button lock You can secure your appliance from being unintentionally the programme terminated e g improper operation by children Activating the button lock Start the required programme Hold down the button B for approx 4 sec until this XL is indicated on the digital display If any button is pressed while the programme is running this LL is indicated on the digital display It is not possible to end Reset the programme Deactivating the button lock Hold down the button LB for approx 4 sec until the display LL goes out When the programme ends 2 07 on the digital display the button lock is cancelled If there is a power failure the button lock is retained Whenever a programme is restarted the button lock must be reactivated Damage The appliance may be repaired and opened up by a technician only To do this disconnect the appliance from the power supply Pull out the mains plug or switch off the fuse Turn off the tap Disposal Make redundant appliances unusable to prevent subseguent accidents Dispose of the appliance in an environmentally friendly manner A Warning Children could become locked in the appliance risk of suffocation or find themselves in other dangerous situations Therefore Pull ou
25. pliance could tip Please note that free standing appliances may tip over if the baskets are overloaded Do not add any solvents to the washing chamber Danger of explosion Open the door carefully when the programme is still running There is a risk of hot water spraying out of the appliance To prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents A Warning Knives and other utensils with sharp points must be placed horizontally in the cutlery drawer Children in the household If fitted use the childproof lock An exact description can be found in the back of the envelope Do not allow children to play with or operate the appliance Keep children away from detergents and rinse aid These may cause chemical burns in the mouth throat and eyes or asphyxiation Keep children away from open dishwasher The water in the rinsing compartment is not drinking water and could contain detergent residue Ensure that children do not place fingers in the tablet collecting tray L231 Small fingers could become caught in the slots Ifthe appliance is installed at eye level ensure when opening and closing the door that children are not caught or crushed between the appliance door and the cupboard door situated below Childproof l
26. r Agua Stop system is defective and causes water damage we will make good the damage for private users To ensure water damage protection the appliance must be connectedto the power supply This liability guarantee is valid for the service life of the appliance A prerequisite for the warranty claim is that the appliance has been correctly installed and connected with Aqua Stop according to our instructions This also includes the correct installation of the Aqua Stop extension original accessory Our warranty does not extend to defective feed lines or fittings up to the Aqua Stop connection on the tap If your appliance is fitted with Aqua Stop you can leave your appliance unattended during operation and leave the tap turned on afterwards The tap should only be turned off if you are absent from home for a prolonged period e g several weeks holiday Siemens Electrogerate GmbH Carl Wery StraBe 34 81739 Munchen To book an engineer visit and product advice GB 0844 8928999 Calls from a BT landline will be charged at up to 3 pence per minute A call set up free of up to 6 pence may apply IE 01450 2655 Please find the contact data of all countries in the enclosed customer service list 9000 489 032 en 8908 Internet www siemens home com 640MG
27. ranged utensils are easier to remove after washing The drawer can be taken out Folding spikes depending on model The spikes can be folded down to improve arrangement of pans bowls and glasses Cup support clip depending on model When washing cups the cup support clip can be folded up The additional inclined position reduces the accumulation of water on the underside of the cup In the case of tall glasses it is recommended to fold down the cup support clip Small accessories holder depending on model Light weight plastic accessories e g Cups lids etc can be held securely in the small accessories holder en Adjusting the height of the basket The height of the upper utensils basket can be adjusted in 3 stages to create more space either in the upper or lower basket Appliance height 81 5 cm Top basket Bottom basket Setting 1 max 16cm 30 cm Setting 2 max 18 5 cm 27 5cm Setting 3 max 21cm 25cm Appliance height 86 5 cm Top basket Bottom basket Setting 1 max 18 cm 33 cm Setting 2 max 20 5 cm 30 5 cm Setting 3 max 23 cm 28 cm Pull out the top basket 21 out To lower the basket press in the left and then the right lever on the outside of the basket In doing so hold the sides of the basket along the upper edge to pre
28. rm for grease and limescale deposits If you find such deposits Fill detergent dispenser with detergent Start the appliance without utensils in the programme with the highest rinsing temperature Clean the appliance with detergents appliance cleaners which are particularly suitable for use with dishwashers Regularly clean door seal with a damp cloth Never use a steam cleaner to clean your dishwasher The manufacturer is not liable for any consequential damage Regularly wipe the front of the appliance and fascia with a damp cloth water and a little washing up liquid are adequate Do not use sponges with a rough surface or abrasive detergents as these could scratch the surfaces Stainless steel appliances To prevent corrosion avoid using sponge cloths or wash them out thoroughly several times before using for the first time A Warning Never use other chlorinated household detergents Health hazard Special salt and rinse aid Check the refill indicators 4 and 5 If required refill salt and or rinse aid en Filters The filters 26 keep large foreign objects in the rinsing water away from the pump These foreign objects may occasionally block the filters The filter system consists of a coarse filter a flat fine filter and a microfilter After each washing cycle check the filters for residue Unscrew filter cylinder as illustrated and take out filter system
29. s only and put the detergent into an absolutely dry detergent dispenser only otherwise the detergent may stick If you switch from combined detergents to solo detergents ensure that the water softening system and amount of rinse aid have been set to the correct value 13 en Overview of programmes The max possible number of programmes is illustrated in this overview The corresponding programmes for your appliance can be found on the fascia Type of utensils Type of soiling Programme Possible additional Programme seguence options Prerinse pots and pans very adhesive burned Clean 70 non sensitive in or dried on food Ej li ej Intermediate rinse utensils remnants containing Intensive 70 Final rinse 65 and cutlery starch or protein Dry auto Is optimised according to all the soiling with the aid Auto 45 65 of sensors t dried common Prerinse mixed utensils par household food o and cutlery Uc Clean 50 remnants eco Intermediate rinse Eco 50 Final rinse 65 Dry Intensive zone Prentiss Clean 40 sensitive utensils Yo Y D Aa Intermediate rinse cutlery 5 tle 40 alf loa UNA H impact pool omre Pease PD rs sensitive plastic y and glasses Us so Clean 45 Extra drying intermediate rinse Quick 45 Final rinse 55 Ea MN An cold rinsing NN Pn all types of utensils intermediate cleaning ae none Prerinse Programme
30. splay 11 Press the START button 9 The programme starts running Programme seguence indicator m m Your dishes are being cleaned AN gt zE Your dishes are being rinsed A Your dishes are being dried 15 en Remaining running time display When the programme is selected the remaining running time of the programme is indicated on the digital display L111 The running time is determined during the programme by the water temperature the number of utensils as well as the degree of soiling and may vary depending on the selected programme Timer programming depending on model You can delay the start of the programme in 1 hour steps up to 24 hours Close the door Switch on ON OFF switch 1 Press button 7 until the digital display 11 jumps to h 5 i Press 7 or button until the displayed time corresponds with your reguirements Press START button 9 timer programming is activated To delete timer programmin the 7 or button until indicated on the digital display You can change your programme selection at any time until the programme starts press 4 07 is End of programme The progra amme has ended when the value G lid is indicated on the numerical display L111 Switching off the appliance Short time after the end of the programme Switch off ON
31. t the mains plug sever and dispose of the power cord Destroy the door lock so that the door can no longer be closed en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in the text Control panel 1 ON OFF switch 21 Programme buttons 3 Display Check water supply 4 Salt refill indicator 5 Rinse aid refill indicator 6 Door opener 7 Timer programming 8 J Additional options 9 START button 10 Programme seguence indicator 11 Digital display depending on model Number depending on model Appliance interior 20 Cutlery drawer 21 Top basket 22 Top spray arm 23 Tablet collecting tray 24 Bottom spray arm 25 Dispenser for special salt 26 Filters 27 Bottom basket 28 Dispenser for rinse aid 29 Detergent dispenser 30 Lock for detergent dispenser 31 Rating plate en Water softening system To ensure good washing results the dishwasher reguires soft water i e containing low amounts of lime otherwise white limescale will be deposited on the utensils and inner container Tap water above 7 dH from set value Hill 1 must be softened The water is softened with salt regeneration salt in the water softening system of the dishwasher The setting and therefore the reguired amount of salt depends on the d
32. teel cleaner Combination detergents function only up to a specific degree of hardness usually 21 dH Over this limit salt and rinse aid must be added As soon as combined detergents are used the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result A Warnings Do not place small parts for washing in the tablet collecting tray 123 this prevents the tablet from dissolving evenly If you want to add more utensils after the programme has started do not use the tablet collecting tray L23 as a handle for the upper basket The tablet could already be there and you will touch the partially dissolved tablet en Notes You will obtain optimum rinsing and drying results by using solo detergents and applying salt and rinse aid separately If programmes are short tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue It is recommended to use washing powder for these programmes The Intensive programme on some models requires one tab only When using washing powder you can apply some of this cleaning agent to the inside of the appliance s door Even if the rinse aid and or salt refill indicator is lit the rinse programme will run correctly with combined detergents If using detergents in a water soluble protective cover Take hold of the cover with dry hand
33. ue of 05 has been reached the display jumps back to r iji off Press START button 9 The set value is saved Switching off rinse aid refill indicator If the rinse aid refill indicator 5 is impaired e g when using combined detergents containing rinse aid component it can be switched off Proceed as described under Setting amount of rinse aid and set the value to r did The rinse aid refill indicator 5 switched off is now Utensils Not suitable Cutlery and utensils made of wood Delicate decorative glasses craft and antigue utensils These decors are not dishwasher proof Plastic parts not resistant to heat Copper and tin utensils Utensils which are soiled with ash wax lubricating grease or ink Aluminium and silver parts have a tendency to discolour and fade during the wash cycle Even some types of glass e g crystal glass objects may turn cloudy after many wash cycles Glass and utensil damage Causes Glass type and glass production process Chemical composition of the detergent Water temperature of the wash programme Recommendation Use only glasses and porcelain which the manufacturer designates as dishwasher proof Use a detergent which protects utensils Take glass and cutlery out of the dishwasher as soon as possible after the program
34. vent it from suddenly dropping To raise the basket hold the basket on the sides of the upper edge and lift it up Before re inserting the basket again ensure that it is at the same height on both sides Otherwise the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit 11 en Detergent You can use tablets as well as powder or liguid detergents for dishwashers but never use washing up liguid The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling Tablets contain an adeguately large amount of active ingredients for all cleaning tasks Modern powerful detergents predominantly use a low alkaline formulation with phosphate and enzymes Phosphates bond the lime in the water Enzymes break down starch and remove protein Phosphate free detergents are less freguent These have a slightly weaker lime bonding capacity and reguire a higher dosage To remove coloured stains e g tea tomato sauce oxygen based bleaching agents are usually used Note To ensure a good washing result always follow the instructions on the detergent packaging If you have further guestions we recommend that you contact the detergent manufacturers helpline A Warning Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agenis 12 need detergent
Download Pdf Manuals
Related Search