Orient Technologies BTP-M280B
Contents
1. gt Windows Server 2003 system 1 Connect USB interface of the printer with idle USB interface of the PC Using USB cable System will recognize USB device automatically and popup Add New Hardware Wizard Select Install from a list or specific location then click Next _ 20 BI P M280 User s Manual 2 Select Search for the best driver in these locations and Include this location in the search then Click on Browse to browse the driver program Default directory is Driver installing packagelUSBDRV2 20 Then click Next 3 Click Continue Anyway on the digital signature interface 4 Click Finish to end the installation AN Caution lt gt Under operating systems Windows XP and Windows Server 2003 if other USB interfaces of PC connected to USB interface of printer firstly The system will also Pop up Add New Hardware Wizard If you have already installed USB device driver according to above steps select Automatic installation and click Next the wizard will search driver automatically then the digital signature interface will pop up Click on Yes and click Finish to end the installation 4 12 How to Use the Driver After installing the driver you can print all characters and images in WORD EXCEL or other file in Windows programs That is What You See Is What You Get In order to print normally you should set the page and select parameters properly 4 12 1 User defined page If the p2. in the driver installing package and read the relative software licensing protocol carefully If you accept it please click 1 Accept then click Next button ol Printer Driver Setup ro Legal Agreement CAREFULLY READ THE FOLLOWING LEGAL Al GREEMENT THE SOFTWARE PROVIDED WITH THIS AGREEMENT THE SOFTWARE IS LICENSED AND ITS USE IS SUBJECT TO THE TERMS AND CONDITIONS BELOW IF YOU DO NOT GHEE TO THE TERMS OF THIS AGREEMENT PROMPTLY DESTROY THE SOFTWARE AND DOCUMENTATION 1 LICENSE GRANT This software is only to be used with the equipment lor which it has be made Beiyang grants to you a non exclusive non transterable right to use the 1 Accept Reject edmark iki Press FI for help lt Back JB Cancel C 2 Select the model and the name of the printer to be installed If you want to set it as default printer please select Set As Default Printer then click Next button Nipeinter Driver Setup Select Install Module Receipt BTP M260 Label Embedded Set As Default Printer Press FI for help lt lt Back B Te BTP M280 User s Manual 3 Select the setup type Advanced then click Next button inter Driver Setup Selup Type C Typical Remarks Support muti USB printer Support driver mode selection Press F1 for help Ba Cancel C 4 Select the current system
3. 6 5 WLAN Interface Board 1 Interface features Supports 802 11b 802 11g protocol Supports 9100 port printing LRP printing Supports status back Supports parameter configuration Supports Firmware update on line VV VV V WV Supports HTTP protocol 2 Protocols supported IP ARP ICMP TCP UDP DHCP TFTP HTTP For detailed specification please refer to User Manual Of WLAN Interface Module VV VV VV WV EE BTP M280 User s Manual 6 6 Power interface definition 1 Pin definition 1 Positive pole 24V 2 Cathode GND 3 NC 2 Interface type Printer end should use Unetop DC 002 or equivalent product User end should use Unetop DP 002 or equivalent product 6 7 Cashdrawer definition 1 Electrical features Driving voltage DC 24 V gt Driving current Max 0 8 A within 510 ms gt Cash drawer status inspection signal L 0 0 5 V H 3 5 V 2 Cash drawer interface outlet uses RJ11 6P connector 3 Interface signal definition DRAWER 1 Cash drawer 1 driving signal DRSW Cash drawer status test signal Cash drawer driving power DRAWER 2 Cash drawer 2 driving signal AN Caution lt gt Do not connect or disconnect signal cable when printer power is on amp Signal cable should be far away strong current amp Signal cable should be far away from strong current sources 239 BTP M280 User s Manual 7 Troubleshooting In case of printer fault consult
4. total thickness lt 0 14 mm AN Caution lt gt Use only multi layer paper 1 original 1 copies of which the original layer on contact the print head thicker than its under layer 2 3 2 Marked paper Besides the requirements of the continuous paper marked paper should follow the following requirements 1 Mark place e BTP M280 printer reserves 8 positions for mark sensor 13 5 which can detect marks on either the front side or the 8 03 reverse side of the paper Position of the sensor is as shown LI AA in the figure e The position of the mark sensor can be adjusted according E to users need The default position Position 1 is on the right side of the paper on the front side paper feed direction Paper feed direction as shown in the figure 2 B M size should meet the reguirement as follow e Mark width L1 5mmsL1s10mm e Mark height L2 12mmsL2s paper width e Distance between marks L3 20mmsL3s500mm 3 The black mark s reflectivity should be less than 15 and the other part s reflectivity should be more than 85 There should be no image between the two marks such as the advertisement etc _5 BTP M280 User s Manual AN Caution lt gt Do not paste the paper to the core 2 4 Ribbon specification 2 4 1 Ribbon model ERC 38 P Purple ERC 38 B R Black Red 2 4 2 Demensions Unit mm S Ribbon 124 5 AN Caution amp Please use the recommended EPSON ori
5. Printout is not clear or dirty Print head or paper feed platen is dirty Clean print head or paper feed platen k heck th Paper cannot be fed normally Paper jam Open back cover to check paper path and remove paper y Ribbon is Ribbon is damaged Replace ribbon ribbon Horizontal printout is missing Print head error Contact your local dealer 34 BTP M280 User s Manual 1 5 Problems during Using Driver Printer can not print when using EA PA NA TAAT TP PAS Refer to 4 11 3 Installing the USB USB interface device driver Print a self test page to confirm serial Configure serial parameter incorrectly configuration of the current printer and configure it correctly fi inti f Parameter of the printer not correct SOON UIE ENO COGN Priming pigas Teer Can not print two color to 4 11 2 Parameter explanation Print mass code with serial interface Used one color ribbon Change to two color ribbon Black k fails to b itioned Select correct paper type in the E EE E Page settings are not correct Sa san Da normally document setting option Extend the overtime of serial and llel Overtime setting is too short Es Printer can not work normally communication referring to the help file under serial parallel interface in the package h hich h Current port is occupied Close other programs which use the port 235
6. Receipt BTP M280 7 Press Fl for help lt lt Back Bl Cancel C 15 BTP M280 User s Manual 3 Select the setup type Typical then click Next button Printer Driver Setup Setup Type Typical Advanced Remarks Install default printer driver gt i Cancel C Press Fl for help Select Install OS Windows 18 Me Windows NI Windows 2000 Ce Windows XP Windows Seecr 2003 f Windows Vista Press FI for help lt Back H LE 4 Set printer port The default port is LPT1 User can install it based on actual port Under Windows NT4 0 or above please select BYCOMx for serial driver x equals to 1 2 3 4 5 6 7 or 8 Click Finish button to end the installation sel Printer Port Ports LPTI COM port setting Baud Rate 95 00 Parity Mon Byte Size E StopBits 1 gt Ul 1 Cancel C 5 If the current system is Windows 98 Me click Yes in the pop up window to restart the computer Press Fl for help 16 BI P M280 User s Manual 4 11 2 Advanced setup Advanced setup is mainly used for users who have special requirements for printer drivers Compared with typical setup advanced setup can support the divers installation of Multi USB printers and has the function of printer driver mode setting Setup steps are as follows 1 Run Setup exe
7. is trimmed and drop the paper roll into the paper cabinet Pull a certain length of paper along the paper out direction then close the back cover and tear off the surplus paper Caution User should adjust the paper guide according to the width of paper roll being used Paper roll should be loaded as shown Trim paper head Paper load mode Paper roll should be rolled tightly to eliminate risk of paper jam or other faults Paper should be loaded in paper cabinet firmly and straight otherwise paper auto load and print will be affected The edge of the paper head is not allowed to deviate from the paper path 4 10 Printer self test 410 1 Turn on the printer 1 2 Ensure the printer is connected with power cable Press of the power switch to turn on and initialize the printer 410 2 self test Ensure the printer is connected with power cable sufficient ribbon and paper roll have been loaded Ensure the printer is powered off Hold FEED button while pressing of the power switch After ERROR LED flashes once release FEED button The printer will print out configuration information and following information Press and Release FEED key to print characters and Press and Hold FEED key to configure the printer then enter hold on status The PAPER LED flashes Press the FEED button for a short time the printer will print a second page with a pattern using the built in character sets press the F
8. type and click Next button Printer Driver Setup elect Install OS C Windows JOM Fo Windows N Windows 2000 Ce Windows XP Windows Server 2013 E Windows Vista Press Fl for help lt lt Back B MS Miz E Cancel 5 Set driver mode and printer port of the printer Default settings are port is LPT1 as default port and supporting Multi USB printers Click Finish to end the installation sel Printer Port LPTI C M port setting Baud Rate 95 00 Parity Mune J Byte Size Stop Bits Protocol Press FI for help Hack iB ME Cancel CJ 6 If the current system is Windows 98 Me click Yes in the pop up window to restart the computer 18 BTP M280 User s Manual 4 11 3 Installing the USB device driver If printer is using a USB interface to communicate before installing the printer driver the user needs to install the USB device driver first The steps for installing the USB device driver are as follows Take XP system as example for detailed introduction gt 1 2 Windows XP system Connect the printer USB interface with idle USB PC interface using USB cable System will recognize USB device automatically and popup Add New Hardware Wizard Select Install from a list or specific location then click Next Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps pon
9. ANCCO SCID A ir 17 4 1o nstallmgtnhe USB device On CF case ea Ra NN 19 AAD FIOW TO USE THE DRIVER S 21 4 121 USeroenned Dal ii ti ads 21 4122 eg ele e A T 22 5 MAINTENANCE anida 28 Oa AN Na bar 28 9 2 MARK SENSOR CLEANING nadal 28 20 CLEAR PAPER JAM oca 28 6 INTERFACE SIG NA BE 30 0 1 E ge 30 62 PAN RA nan nb 30 6 9 SERIALINTERFAC ena 31 SE EE 31 6 5 WEAN INTERFACE BOARD an aah 32 6 6 POWER INTERFACE DAN Na AA 33 6 7 CASHORAWER DEFINITION ee 33 T TROUBLESHOOTING idas 34 7 1 CUTTER ERROR TROUBLESHOOTING intan 34 BTP M280 User s Manual 2 PRINTER DOESN T WORK a 34 TO ERROR LED AND BUZZER RI an en BB 34 TA PROBLEMS DURING IRIN TIN ih nan AS EAE ads 34 9 PROBLEMS DURING USING DRIVERS naaa AAA 35 BTP M280 User s Manual Declaration Information in this document is subject to change without notice SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO LTD hereinafter referred to as SNBC reserves the right to improve products as new technology components software and firmware become available If users need further data about this product or have any doubt about safety issues that might arise from using it please feel free to contact SNBC or your local agents No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of SNBC Copyright Copyright O 2007 by SNBC Printed in China Version 2 0 Trademarks S
10. EED button for a long time the printer will enter into button configuration mode For detail function and operation method of button configuration mode please contact your dealer 14 BTP M280 User s Manual 4 11 Installing the Printer Driver BTP M280 printer offers the drivers under Windows 98 Windows NT4 0 Windows 2000 Windows XP Windows server 2003 Windows Vista with the installing steps as below 4 11 1 Typical setup 1 Run Setup exe in the driver installing package and read the relative software licensing protocol carefully If you accept it please click 1 Accept then click Next button Printer Driver Setup ok Legal Agreement CAREFULLY READ THE FOLLOWING LEGAL Goal GREEMENT THE SOFTWARE PROVIDED WITH THIS AGREEMENT THE SOFTWARE IS LICENSED AND ITS USE IS SUBJECT TO THE TERMS AND CONDITIONS BELOW IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT PROMPTLY DESTROY THE SOFTWARE AND DOCUMENTATION 1 LICENSE GRANT This software is only to be used with the equipment lor which it has be made Beiyang grants to you a non exclusive non transterable right to use the CIA al 1 Accept Aeject Press F1 for help lt Back Bl Cancel C 2 Select the model and the name of the printer to be installed If you want to set it as default printer please select Set As Default Printer then click Next button Select Install Module
11. ERROR LED is always off under error conditions ERROR LED will flash PAPER LED 6 Indicate paper status of the printer Under normal conditions PAPER LED is always off under paper end or paper near end conditions it is always on FEED button 7 Press the button while turning on the printer a self test page will be printed In the normal status press the FEED button for a short time the printer will feed paper one line at a time Under continuous paper mode hold the FEED button the printer will feed paper constantly Under marked paper mode it will feed paper to the next mark In HP error status hold the FEED button for a long time the printer will recover from HP error and start carriage verify check In cutter error status hold the FEED button for a long time the printer will recover from cutter error and start cut In error status other than described above press FEED button the printer will have no action 8 BI P M280 User s Manual 5 Power switch 8 Turn on off the printer O is to turn off the printer is to turn on the printer 6 Back cover latch 9 Catch back cover latch and pull it out to open the back cover 7 Paper near end sensor 19 Detect the status of paper roll If paper near end the PAPER LED will on the ERROR LED will flash and indicate user to replace paper The printer will continue printing until the paper is end 8 Paper sensor 21 Paper sensor is used to detect the printer with or w
12. Font Version Control Font Setting Gontral East El Edit control font character translation table Print a self test page SelfTest Daan a a a A AAN ATA AA AA AAA Check that communication settings le correct User Defined Paper Size Form Name Custom Paper Size M 280 width 200 S 410 800 0 4mm Height 2370 254 40000 Ummi User can set control font and print self test page via this option at the same time user can set 25 BTP M280 User s Manual gt Download 2 BTP M280 P Properties Device Settings Utility Download File Download Version Toy can select various files to download to the printer such as firmware files font files Download Logo Download Download all Clear All Logos User can download firmware and Logo via this option gt Font 2 BTP M280 P Properties Version a Font A Eg Fontal 9 0 Sa Font 12 18 0 Sa Font 21 90 lg Fomt 22 18 0 a Font E NG 9 0 Ge Control Font i ES Control 1 0 Select this font size in the application User can select driver supported font and font size via this option 26 BTP M280 User s Manual gt Version information BTP M280 P Printing Preferences BTP M280 Printer Driver Setup BIHMZOU EM Install Version 1 0 Copyright E 2007 All Rights Reserved Apply User can see the printer driver version information via this opt
13. NBC registered trademarks are SNJC BEIYANG Warning and Caution AN Warning Items should be strictly followed to avoid damages to body and equipment AN Caution Items with important information and prompts for operating the printer The guality control system of SNBC has been approved of the following certification ISO 14001 REGISTERED DNV 1509001 2000 1 91 AVE DNV Certification B V The Netherlands manda lt cD gt The environmental control system of SNBC has been approved of the following certification ISO 14001 REGISTERED A DNV ISO14001 2004 e D 910 DNV bur DNV Certification B V The Netherlands S BTP M280 User s Manual General Safety Instruction Before installing and using the printer please read the following items carefully 1 Safety Instructions AN Warning Do not touch the tear off bar of the printer Warning The print head is at a high temperature during printing or just after operation do not touch it and its peripherals for reasons of safety En Warning The print head is an ESD sensitive device To prevent damage do not touch either its printing parts or connecting parts 2 Cautions 1 Install the printer on a flat and stable surface 2 Reserve adequate space around the printer so that convenient operation and maintenance can be performed 3 Keep the printer away from water source direct sunlight strong light
14. Selection Paper Source Automatically Select Mecha Roll Paper Color Se E O Black amp White Colo e In this option user can choose Color or black and white Only when user chooses Color they can print two colors Setting resolution parameter BTP M280 Advanced Options HS BTP M280 Advanced Document Settings 8 lg Paper Output Paper Size 76mm x 9 mm Copy Count 1 Copy 8 iin Graphic Print Quality 160 x 72 dots per inch E O Image Color Ma af 160 x 144 dots per inch ICM Method ICM Intent 22 80 x 72 dots per inch ES iiss Document Options Advanced Printing Features Enabled Color Printing Mode 6 Color Halftoned Halftoning Auto Select wi Print Optimizations Enabled ey Printer Features Print Quality Bi_directional print Paper Conservation Enable BTP M280 driver supports three kinds of resolutions 160 x 144 dpi 160 x 72 dpi 80 x 72 dpi Users can select it according to their own need High resolution has clear printing while lower print speed low resolution has higher print speed while less clear printing 08 BTP M280 User s Manual gt Single Bi directional print setting BTP M280 Advanced Options a BTP M280 Advanced Document Settings aL Paper Output Paper Size 76mm x 297 mm Copy Count 1 Copy a in Graphic Print Quality 160 x 72 dots per inch EME Image Color Management co ICM Method ICM Disabled ICM Intent Pictures l iiss Do
15. USER S MANUAL Impact Receipt Printer BTP M280 Shandong New Beiyang Information Technology Co Ltd BTP M280 User s Manual Contents Over o a ENA 3 df bet 3 IPAR KE dn A nan NN EE 3 2 SPECIFICATIONS 0 dd e 4 2 EMAIN PECIFICATION ted ea dad ad 4 22 GUTTER SPECIFICATION ER 5 ZO PAPER OPE CIPI CA TIOIN EE 5 ZO DON MUS e Ee 5 SE EE Ee 5 ZA RIBBON SPECIRCATON aa aras criadas 6 ZA IDO eler e EE 6 2A MINA OS EE 6 2 5 PRINT AND TEAR OFF POSITION NEE T Ze E FANE OSU OVI eebe 7 292 lOa ON POSION GE 7 3 OUTLINE AND PARTS EEN 8 Sak Oa AN PS oda sn tava hs he asc to narcosis EE 8 22 LEDS AND BUZZER EE 9 4 INSTALLING ies aa aan EE 10 O A NN ee eee 10 4 2 MOUNTING THE PRINTER EE 10 ANACO ZONA QUAN EE 10 4 2 2 Wall IMOUNUNG Optional Lia ai deg 11 4 3 CONNECTING TO A GROUND LINE Me td EN Sa 11 4 4 CONNECTING THE POWER ADAPTER cccccececcacecccccceccccaceceaceceacaceceaeeueeueeauaceneaesueceseeneaeeneausnesesnsneanenes 12 AS lt SONNECTING USB SIGNAL CABE asu 12 4 6 CONNECTING OPTIONAL SIGNAL CABLE 0c2ccccececcocececccceccccececccceceacececccceceaceceacstecceceneausceceececeausceaeenss 12 BTP M280 User s Manual 4 CONNECTING THE CASH DRAWE Raids 12 EE Eege 12 4 So DiING PA Ro ai 13 AO FAPA EE 13 4 9 2 Loading replacing paper TOW vi AA A AE A A eee eaed 13 A TOPRNTER SELF TEST daa oo 14 410 1 TUKOM WIC EE 14 EE EE 14 4 11 INSTALLING THE PRINTER DRIVER sisik nisan kubuka ea kuta akn 15 PNS Wee EE 15 4 22 AQV
16. age size defined by the driver can not meet user s requirement user can define the page size under Window 98 system user defined page can be defined via page settings But under Windows NT4 0 Windows 2000 Windows XP Windows server 2003 Vista user cannot define page size via page settings The following steps introduce how to define page size take Windows XP system as an example 1 Ensure the system running normally 2 Click Start button 3 Click Printers and faxes in Settings item or first click Control panel button then click Printers and other hardware in Control panel next click Printers and faxes button 4 After selecting BTP M280 click File menus then click Service Properties submenus 3 Printers and Faxes File Edit View Favorites Tools Help O Search 55 Folders Ek 5 Open Printing Preferences Pause Printing Mame Documents Status Corr Sharing Ei BTP MesotP o Ready Use Printer Offline Add Printer Server Properties hces Set Up Faxing Create Shortcut Delete Rename Properties Close Other Places A Control Panel UX Eranmere and Camarar 5 In Forms item select Create a new form 6 Define a name of self defining paper in Form name oD BI P M280 User s Manual 7 Take metric CM as measurement units Define paper width length right left and up down margin of the printing area according to users
17. and P means signal source from printer 30 BTP M280 User s Manual 6 3 Serial interface The printer serial interface is compatible with RS 232 standard of which the outlet is 25PIN female D type Pin Signal definition Pame rod User can query interface settings status via a printing configuration sample The default setting is as follows Baud rate 9600bps Data bit Gbits Parity bit None Stop bit 1 bit Flow control DTR DSR 6 4 Ethernet 1 Interface features Support of 10BASE T communication Compatible with Ethernet II standard frame type Indicator shows network connecting status and data transmission status Supports 9100 port print Supports status back Supports parameter configuration Supports firmware update on line Y YV VV VV WV Supports printer status query and interface module maintenance based on HTTP 2 Protocols Supported IP ARP ICMP TCP UDP DHCP TFTP HTTP VV WM WM WM WM v WV e BI P M280 User s Manual 3 Electrical features Output signal The available differential mode voltage is more than 450mV and peak voltage is less than 13V The common mode AC peak voltage is less than 2 5V gt Input signal The differential mode voltage that more than 160mV is identified as available signal 4 Interface shall use RJ45 outlet which accord with 10BASE T standard of IEEE802 3 5 Interface signal definition CECR NC Reserve O reg AA TO rene
18. and heat 4 Do not use or store the printer in a place exposed to heat or fire moisture or other pollution 5 Do not place the printer on a place exposed to vibration or impact 6 Avoid exposing the printer to condensation In case of condensation ensure it has been completely removed before turn on the power 7 Connect the power adapter to an appropriate grounded outlet Avoid sharing a single electrical outlet with large power motors and other devices that may cause the fluctuation in voltage 8 The socket outlet should be installed near the equipment and should be easily accessible 9 Turn off the power if you do not use the printer for a long time 10 Do not spill water or other electric substances like metal on the printer If this happens turn off the power immediately 11 Do not allow the printer to start printing when there is no paper otherwise the print head and platen roller will be damaged 12 To ensure print quality and normal lifetime use recommended or good quality paper and ribbon 13 Shut down the printer when connecting or disconnecting interface connectors to avoid damage to the control board 14 Do not disassemble the printer without guidance from a technician even for the purpose of repair 15 Keep this manual safe and at hand for reference purpose BTP M280 User s Manual 1 Overview 1 1 Outline The BTP M280 is a 9 pin serial impact dot matrix receipt printer offering high quality high speed a
19. be installed because itis either not digitally signed or not signed in the appropriate manner Contact pour hardware vendor Click Finish to close the wizard lt Back f Finish Cancel gt Windows 98 Me system 1 Connect USB interface of the printer with idle USB interface of the PC Using USB cable System will recognize USB device automatically and popup Add New Hardware Wizard then click Next 2 Select Search for the newest driver for your device then click Next 3 Select Specify a location click Browse button to browse the driver document Default directory is driver installing packagelUSBDRV2 20 then click Next 4 The wizard will indicate the device drivers name that have found Then click Next 5 Click Finish to end the installation gt Windows 2000 system 1 Connect USB interface of the printer with idle USB interface of the PC Using USB cable System will recognize USB device automatically and popup Add New Hardware Wizard then click Next 2 Select Search for the best driver for your device click on Next 3 Select Specify a location then click Next 4 Click Browse button to browse the driver program Default directory is Drivers installing package USBDRV2 20 5 The wizard will indicate the device drivers name that have found Then click Next 6 Click Yes on the digital signature interface 7 Click Finish to end the installation
20. cument Options Advanced Printing Features Enabled Color Printing Mode 8 Color Halftoned Halftoning Auto Select Print Sptimizations Enabled S Ei Printer Features 2 Print Quality Bi directional print ae Paper Conseryd Uni directional print Set single bi directional print settings via this option Operation option Start of Page Operation when page starts End of Page Operation when page ends End of Document Operation when document ends User can set different setting of page via this option start of document start of page end of page end of document e BTP M280 User s Manual Document setting option Start Document Operation 0 Drawer Cash Drawer 1 H2 el 16 Sl ms 16 250 O Herald Buzzer Beep off w Paper Feed I mm U 100 ME _ Feed to cut position before cut Paper Cut Manual Cut Print Logo Not Print Logo Align aft Centered Position User can set parameters via this option on the start of document end of document start of page and end of page Cash drawer Cash drawer1 Cash drawer2 Cash drawer1 2 print messenger Herald and Cash drawer pulse width Buzzer Buzz 200ms 600ms 1s 2s 4s paper feed paper cut paper cut by hand partial cut full cut print Logo bitmap gt Utility user defined page size BTP M280 P Properties General Sharing Pop Advanced Color Management Device Settings Up Download
21. efault Character Font B 40 CPL 36 CPL 30 CPL Character size Default Font A 1 6x3 1mm Font B 1 2x3 1mm Chinese 2 7x2 9mm Characters inch Default Font A 13 3CPI Font B 16CPI Chinese 8 9CPI Receive buffer 4KB NV bit image data area 128KB User NV memory 8KB ERC 38 ribbon cartridge ERC 38 P 4 000 000 characters ERC 38 B 3 000 000 characters Data buffer Ribbon specification Ribbon lifetime Black 1 500 000 characters Red 750 000 characters Communication interface USB Fixed IEEE1284 RS 232 Ethernet Wi Fi interface optional ERC 38 B R Cash drawer connector 1 2 cash drawers Power supply DC 24V 5 average current 1 5A 10 000 000 lines 150 000 000 characters 1 000 000 times Printing Mechanism lifetime Reliability Print head lifetime Cutter Operating temperature and humidity 5 45 C 20 90 RH 400 Storage temperature and humidity 40 60C 20 93 RH 400 Dimensions 160mm W x245mm D x145mm H Weight 2 9kg BTP M280 User s Manual 2 2 Cutter specification er TI Tee ma Operation voltage 24VDC 2 3 Paper Specification 2 3 1 Continuous paper 1 Normal paper gt Paper width 80 0 5mm 76 0 5mm 69 5 0 5mm 57 5 0 5mm gt Max paper roll O D HK83mm gt Paper roll core ID H12 5mm OD 16mm gt Paper thickness 0 06 0 085mm 2 Multi layer paper 1 original 1 copies gt Paper width 80 0 5mm 76 0 5mm 69 5 0 5mm 57 5 0 5mm gt Paper thickness 0 05 0 08mm
22. ginal ribbon to ensure the printing guality and lifetime of the printer transmission part BTP M280 User s Manual 2 5 Print and Tear off Position 2 5 1 Print position L1 Paper width L2 Print width L3 Print left margin Paper feed direction L4 Print right margin According to the different paper width of the L1 the print width L2 and the left right margin L3 L4 should be changed as below Paper width L1 Print width L2 Left margin L3 Right margin L4 2 5 2Tear off position L1 About 21 5mm Tear off position L2 About 34mm Auto cut positon First line print position BTP M280 User s Manual 3 Outline and Parts 3 1 Outline and Parts 1 Back cover 2 Tear off bar 3 Front cover 4 POWER LED 5 ERROR LED 6 PAPER LED 7 FEED button 8 Power switch 9 Back cover latch 10 Communication interface 11 USB interface 12 Cash drawer connector 13 Power connector 14 Power pack optional 15 Cutter sliding Blade 16 Platen roller 17 Paper near end sensor regulator 18 Ribbon 19 Paper near end sensor 20 paper cabinet 21 Paper sensor 22 Mark sensor 23 Back cover sensor 24 Paper guide Functions of parts 1 2 LA 4 POWER LED 4 Indicate power status on off When turning on printer POWER LED is always on when turning off printer POWER LED is always off ERROR LED 5 Indicate all error status Under normal conditions
23. install software for USB Device Driver for POS AKIOSEK Printers IF pour hardware came with an installation CD A or floppy disk insert it now What do pon want the wizard to do C Install the software automatically Recommended Select Search for the best driver in these locations and Include this location in the search then Click Browse to browse the driver document Default directory is Driver installing packagelUSBDRV2 20 Then click Next Found New Hardware Wizard Please choose your search and installation options 8 Search for the best driver in these locations Use the check boses below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Search removable media floppy CD ROM Include this location in the search C VUSEDRV2 20 w Browse Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the diver you choose will be the best match for pour hardware 19 BI P M280 User s Manual 3 Click Continue Anyway on the digital signature interface 4 Click on Finish to end the installation Found New Hardware Wizard Cannot Install this Hardware There was a problem installing this hardware y USB Device An eror occured during the installation of the device The driver cannot
24. ion el BI P M280 User s Manual 5 Maintenance AN Caution lt gt For daily maintenance be sure the printer is turned off lt gt Do not use gasoline acetone or other organic liquids to clean any parts of the printer lt gt When cleaning the sensor please leave the printer off until the alcohol completely dried lt gt Recommended maintenance cycle shall be no longer than a month 5 1 Roller cleaning Steps for roller cleaning are as follows 1 Turn off the printer power 2 Pull the latch to open the back cover as shown in the figure 3 Keep the back cover open clean the dust and duty on the platen roller using a soft cotton cloth with little moderate cleanser 4 Wait until the cleanser is completely evaporated then close the back cover and finish roller cleaning 5 2 Mark sensor cleaning If the printer does not identify the mark effectively you should clean the mark sensor Steps for mark sensor cleaning are as follows 1 Turn off the printer 2 Pull the latch to open the back cover of the printer 3 Keep the back cover open clean the dust and dirt off the mark sensor using a soft cotton cloth with a little alcohol 4 Wait until the anhydrous alcohol completely evaporated then close the back cover and finish mark sensor cleaning 5 3 Clear paper jam When the printer in one the following situations you should clear the paper jam gt Paper can not get out normally gt Excessive noise occur
25. ithout paper 9 Mark sensor 22 When using mark paper mark sensor is used to detect mark 10 Back cover sensor 23 Back cover sensor is used to detect the position of the back cover 11 Paper guide 24 There are three long slots at the bottom of paper cabinet The paper guide could be plugged in different slot which is suitable for different wide paper such as 76 5 0 5 mm 69 5 0 5 mm 57 5 0 5 mm Without paper guide paper width of the printer is 80t0 5 mm AN Caution lt gt The paper guide is a necessary part of the printer for adjusting paper width please keep it carefully 3 2 LEDs and Buzzer The table below shows LEDs and buzzer in error status e mae TI mem E Three sounds apor arena eme O ason COC AN Caution lt gt The printer checks the print head temperature via thermal resistor If the print head is extremely overheated the printer will stop printing BTP M280 User s Manual 4 Installing 4 1 Unpacking When unpacking you should check whether all parts are present and undamaged in accordance with the packing list If any part is missing or damaged please contact SNBC or your local agent 4 2 Mounting the Printer BTP M280 has two mounting modes horizontal mounting and wall mount 4 2 1 Horizontal mounting The printer should be mounted on a flat and stable surface For operation and maintenance we suggest you reserve space below the printer to ensure its reliability and easy operati
26. nd stable performance lt is widely used in real time printing on site such as POS system kitchen and finance applications The BTP M280 can be connected with other devices via USB parallel serial Ethernet and WLAN interface USB interface is a fixed interface of the printer and the other interfaces are optional interface of the printer The BTP M280 offers drivers and applications under WINDOWS 98 NT4 0 2000 2003 XP Vista 1 2 Features Bi directional printing Two color printing Bi directional carriage return Support multi layer paper Easy paper loading Easy operation and maintenance Support marked paper and continuous paper for print Compatible with various wide paper Cutter paper automatically Cash drawer control connector Communication interface optional VV VV VV VV VV vv Printer firmware updated online BTP M280 User s Manual 2 Specifications 2 1 Main Specification Specification Print mode Print speed Max 4 7LPS 400 dots line Print width Max 400 half dots 200 full dots 9 pin serial impact dot matrix Paper type Continuous paper or marked paper Paper width 80 0 5mm 76 0 5mm 69 5 0 5mm 57 5 0 5mm Paper thickness 0 06 0 085mm Multi layer paper Paper width 80 0 5mm 76 0 5mm 69 5 0 5mm 57 5 0 5mm 1 original 1 copies Papei Single layer Paper thickness 0 05 0 08mm total thickness lt 0 14 mm Character type Font A 9x9 FontB 7x9 Chinese 16x16 Characters line D
27. on gt BTP M280 power supply external 10 BI P M280 User s Manual 4 2 2 Wall mounting optional Wall mount is an optional function The wall mount mode is shown as below 1 Two 50mm deep holes should be made with a hammer drill in a suitable wall of the sizes shown below de 80 S e 2 Insert plastic plugs and screws into dp holes and ensure that the end sides of the plugs are flush with the surface of the wall 3 Put the screws into plastic plugs with screwdriver keeping a distance of 10mm between screw head and wall side wall A plastic plug 4 Install the printer according to the arrowhead AN Caution lt gt In case of wall mount the printer must be oriented upwards amp The hook on the wall should be firmly positioned to avoid printer damage or risk of falling 4 3 Connecting to a ground line Printer housing should be grounded Please ensure the material is AWG18 or 7 Los equivalent 1 Turned off the printer SCH ag 2 Loosen the ground line screw and connect it to back case of printer with LSS me h screwdriver 11 BI P M280 User s Manual 4 4 Connecting the Power Adapter 1 With the flat side of the power adapter s cable connector facing downward insert the cable connector into the power connector on the backside of the printer 2 Turn on the input power source of the adaptor AN Caution lt gt lt gt Use only the supplied powe
28. own need A Print Server Properties Ax Forms Ports Drivers Advanced Forme on RAINBOW r mm 297 mm Delete Timm v 3276 mm Ca Temm s 297 mm 76mm x 3276 mm DI Form name 76mm 237 Create a new form Define a new form by editing the existing name and measurements Then click Save Form Form description measurements Units O Metric 6 English Paper size Printer area margins Width 2 Om Left O0 00in Tom DUU Height 11 bim Right 0 Dn Bottom UL Um Cancel 8 Click Save Form button to save the form 9 Click Apply button to finish paper self definition AN Caution lt gt Before setting user defined page please ensure that the printer driver has been installed properly lt gt In application you can select the page in varieties of official software such as WORD EXCEL and so on 4 12 2 Parameter explanation The driver offers cut mode paper type and cash drawer functions for users to use Users can configure the parameters according to their needs Take Windows XP system as an example to describe how to set the driver parameters Setting paper type 3 BTP M280 P Printing Preferences Tray Selection Paper Source Automatically Select O Calor 22 BI P M280 User s Manual Optional paper type roll paper and marked paper gt Color choose BTP M280 P Printing Preferences Lawout Paper Cluality Operation Version Tray
29. pen front cover of the printer as shown en a BI P M280 User s Manual 3 Turn the ribbon knob two or three times according to the mark to tighten the ribbon 4 Referto the figure to install ribbon to the correct position 5 Turn the ribbon knob two or three times according to mark to tighten the ribbon again AN Caution lt gt The print head will become hot during printing To avoid harm or injury please do not replace the ribbon until it cooled down lt gt Ribbon should be mounted between print head and paper without folds or drapes 4 9 Loading Paper Roll 4 9 1 Paper type Before loading roll paper you should confirm the type of the paper can be used for printer The default paper type is continuous paper lf marked paper will be used please contact your local dealer for assistance 4 9 2 Loading replacing paper roll 1 Press back cover button to open the back cover 2 Hold the hole in the paper guide to install or offload it When using 76mm 69mm 57mm width paper roll user needs to insert paper guide vertically into a suitable location When using 80mm width paper roll the paper guide doesn t need to be placed into the printer but please keep it safely in case of using in the future N Notes Without paper guide 80 0 5mm With paper guide A 76 0 5mm B 69 540 5mm C 57 5 0 5mm DER ER 4 A lt gt lt gt lt gt BTP M280 User s Manual Ensure the paper head
30. r adapter or other equal model When connecting or disconnecting cable connector of the power adapter you should pull on the connector not pull on the cable by force lt gt Do not pull on the power adapter cord Otherwise the cord may be damaged or broken causing a risk of fire or electric shock lt gt Do not place the power adapter cord near a heating device otherwise the cover of the cord may melt causing a risk of fire or electric shock lt gt When the printer is not used for a long period of time disconnect the power adapter from the wall outlet for safety 4 5 Connecting USB signal cable 1 Ensure the printer is turned off 2 As shown the figure below put the USB signal cable into the suitable s e Gs USB interface ES no 3 Connect other end of USB signal cable to host 4 6 Connecting optional signal cable 1 Turned off the printer h T 2 Put the signal cable into suitable connector and fix it with plug screw or H x E i clip spring S ee 3 Connect other end of the signal cable to host 4 7 Connecting the Cash Drawer 1 Turned off the printer 2 Insert the cash drawer cable into the cash drawer connector on the backside of the printer AN Caution lt gt Do not connect a telephone line to the cash drawer connector otherwise the printer and the telephone line may be damaged 4 8 Installing Ribbon 1 Ensure that ribbon type is standard ERC 38 2 O
31. s with paper feeds Steps for cleanup paper jam are as follows _ 28 O N gt se e iN BI P M280 User s Manual Turn off the printer Pull the latch to open the back cover of the printer Check if there is any paper in the paper path if necessary clear the jammed paper Close the back cover and finish clearing paper jam 29 BTP M280 User s Manual 6 Interface Signal The BTP M280 can be connected with other devices via USB parallel serial Ethernet and WLAN interface USB interface is a fixed interface of the printer and other interfaces are optional 6 1 USB interface The printer USB interface supports USB1 1 protocol of which the outlet is USB A type Interface signal is defined as below 6 2 Parallel interface The parallel interface of printer is bi directional and supports the BUSY ACK handshake protocol and the nibble protocol The interface outlet is 36PIN CENTRONICS Signal resource Signal definition Pin Signalresource Signal definition Data 0 Least Significant Bit mi Signal Ground az grana O os a Sinateroma aa l soom O os e l socom ae s sacom Data 7 Most Signiicamteiy 27 Signal Ground ke a aaa a aaa remar a sacom mw O rw noema a O ooa tee nap emea onasssana Pas JO tened h H H H H H H H H D D D P H Pin 6 8 BEN D 18 AN Caution lt gt H means signal source from a host
32. this section for solutions and advice If you do not find a solution in this section please contact your local dealer for assistance 7 1 Cutter error troubleshooting When cutter fails to recover due to paper jam or sudden off line status perform the following actions 1 Turn off power of the printer 2 Pull the latch to open the back cover of the printer 3 Power on the printer the cutter will be reset automatically AN Caution lt gt To avoid injury please do not touch the sliding blade of the cutter when printer is power on 7 2 Printer doesn t Work l Make sure that printer cable has been connected properly on both E Printer power is off LED is off and the ends printer doesn t work Printer is not turned on Circuit is damaged Contact your local dealer 7 3 Error LED and Buzzer Problems Possible causes Sotuton O Refer to 7 1 Cutter error troubleshooting Error LED flashes and buzzer beeps Input voltage abnormal Turn off printer power and check input voltage rica vemested Turn off printer power and wait until the print head turn to normal temperature If ribbon is damaged replace ribbon HP error Press 4 hold FEED button or power on the printer again 7 4 Problems during Printing Problems Possible causes Somon Printout is light and not clear Ribbon ink is out Replace ribbon firm if tch Always feed paper in printing Ka Wipe melenee Replace with correct roll paper with the paper used
Download Pdf Manuals
Related Search