Metra 99-7602 mounting kit
Contents
1. White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 7 NOTES 99 760 NOTES nan 99 7602 INSTRUCTIONS L 1 800 221 0932 m www metraonline com REV 08 11 09 COPYRIGHT 2004 2009 METRA ELECTRONICS CORPORATION INST99 76022. holes on the factory bracket and mount the factory bracket to the ISO units using screws supplied with the radio Figure A Attach the assembled units and brackets to the radio trim panel using the factory screws removed during disassembly Figure B Continue to final assembly M ZZ 939 7602 FINAL ASSEMBLY i GN FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown Metra recomends using the proper mating adapter and making the connections as shown Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit 2 _ Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the radio Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit A Strip wire ends back 1 2 B Twist ends together C Solder D Tape METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue
3. INSTALLATION INSTRUCTIONS FOR PART 99 7602 APPLICATIONS Nissan 350Z 2006 2008 99 7602 KIT FEATURES e DIN Radio Provision with pocket e ISO Radio Provision with pocket e Two stacked ISO units provision e Double DIN radio provision KIT COMPONENTS A Radio Housing with Pocket B Double DIN Trim plate C ISO Snap in Brackets D ISO Trim plate WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 7550 Nissan harness 1995 up e 70 7551 Nissan amp interface harness 1995 up Antenna Adapter e Not required TOOLS REQUIRED Panel Removal Tool or Small Flat Blade Phillips Screwdriver L 1 800 221 0932 www metraonline com COPYRIGHT 2004 2009 METRA ELECTRONICS CORPORATION SL MEET TABLE OF CONTENTS Dash Disassembly Nissan 350Z 2006 200B srssscsersrsssesersssrsersesssesersnsnserensnsesmssnsecsnsnsereesneases 1 2 Kit Assembly Din Mount Radio Provision With DOCKet zusenssensseennseennneennnnunnnnunnnnunnnnannnnnnnnnnannnn 3 ISO Mount Radio Provision With pocket 4 Double DIN R amp iO sssssessssessssessessesessssessessssessesessasessossscessasessosscsessocassessscessacerseceseesseces 5 Two Stacked ISO mount UnitS ressssccsscssessessssssssessessssessessessessessssessessessessessessseescaseess 6 FINAL ASSEMDI RER KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our ind
4. e A 2 Place the double DIN trim plate on the front of the radio Figure B Remove 3 Place the right factory mounting bracket Removed from radio during disassembly on the right side of the radio Align the pins on the trim plate with the holes on the factory bracket and mount the factory bracket to the radio using screws supplied with the radio Figure B 4 Place the left factory mounting bracket removed from radio during disassembly on the left side of the radio Align the pins on the trim plate with the holes on the factory bracket and mount the factory bracket to the radio using screws supplied with the radio Figure B A L Y i oa a Il i 5 Attach the radio bracket assembly to the ini il a i WO radio trim panel using the E factory screws removed during 5 disassembly Figure C Continue to final assembly er 9 72 99 7602 KIT ASSEMBLY TWO STACKED ISO MOUNT UNITS Place the double DIN trim plate on the front of the two ISO units Figure A Place the right factory mounting bracket Removed from radio during disassembly on the right side of the ISO units Align the pins on the trim plate with the holes on the factory bracket and mount the factory bracket to the ISO units using screws supplied with the radio Figure A Place the left factory mounting bracket Removed from radio during disassembly on the left side of the ISO units Align the pins on the trim plate with the
5. p for DIN or ISO installations with pocket Continue to kit assembly al 99 7602 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET 1 Slide DIN cage supplied with radio into the radio housing from the front Figure A 2 Secure DIN cage to radio housing by bending the locking tabs outward Figure A 3 Slide the radio into the DIN cage until it snaps into place Figure B 4 Attach the radio housing assembly to the radio trim panel using the factory screws removed during disassembly Figure C Continue to final assembly Mz 99 7602 KIT ASSEMBLY ISO MOUNT RADIO WITH POCKET 1 Align the holes in the ISO brackets with the holes in the radio Mount the brackets to the radio using screws supplied with the radio Figure A 2 Slide the radio bracket assembly into the radio housing until it snaps into place Figure B 3 Snap the ISO trim plate onto the front of the assembled radio and housing Figure B 4 Attach the radio housing assembly to the radio trim panel using the factory screws removed during disassembly Figure C Continue to final assembly NOTE To remove the radio unsnap and remove the ISO trim plate Using a flat blade screwdriver disengage ISO brackets from the radio housing and slide radio out of radio housing Meta O9 602 KIT ASSEMBLY DOUBLE DIN RADIO 1 Cut and remove center divider from double DIN trim plate Figur
6. ustry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow A he 0 Mi 99 7602 DASH DISASSEMBLY NISSAN 3507 2006 2008 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 For vehicles with automatic Trim Ring transmission Unsnap and remove smaller trim ring from around shifter Figure A For vehicles with manual transmission Unscrew and remove shifter knob Figure A 3 Unsnap and remove center console trim panel including climate controls Figure B 4 For vehicles with navigation Unsnap and remove navigation switch panel Figure C 5 For vehicles without navigation remove pocket mat then remove two screws that secure switch mask Figure D 2 Screws Y MESA 99 7602 DASH DISASSEMBLY NISSAN 3507 2006 2008 6 Remove 2 screws above the radio and 2 screws below the radio Also remove 2 screws securing the radio trim panel assembly Figure E 7 Unplug and remove the radio trim panel assembly Figure F 8 Remove 4 screws securing the radio to the trim panel and remove the radio 9 Remove 8 screws securing the factory brackets to the radio and remove the brackets from the radio These brackets are required for stacked ISO and double DIN installations You can skip this ste
Download Pdf Manuals
Related Search