Omnitron FlexPoint T1/E1
Contents
1. hon Local Dual Loop Back sacle a Remote amp Local Loop Back a Force 1 s to Fiber B Force 1 s Copper Warning The operating description in this Instruction Manual is for use by qualified personnel only To avoid electrical shock do not perform any servicing of this unit other than that contained in the operating instructions unless you are qualified and certified to do so by Omnitron Systems Technology Inc Caution All user required operations can be performed without opening the unit Never attempt to open or remove the cover or tamper with the unit Warranty This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment TO REGISTER COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS Or you may register your product on the Internet at htto www omnitron systems com During the warranty period Omnitron will at its option repair or replace a product which is proven to be defective For warranty service the product must be sent to an Omnitron designated facility at Buyer s expense Omnitron will pay the shipping charge to return the product to Buyer s designated US address using Omnitron s standard shipping method Local l2. Before inserting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source Mounting instructions The FlexPoint Fiber Converter can be solo mounted using a wall mounting kit or rack mounted using a 5 unit shelf or a high density FlexPoint 14 Unit Power Redundant Chassis Fiber Optic Cable Attachment Connect the fiber cables between the FlexPoint T1 E1 converters The transmit Tx must attach to the receive side and the receive Rx must attach to the transmit side Note Use fiber cables that are compliant with the specifications that are outlined in fiber cable specifications Copper Cable Attachment RJ 45 RJ 48 T1 E1 connector Connect to the RJ 45 48 connector on the FlexPoint T1 E1 converter via a category 3 or better cable Category 5 is recomended and attach the other end to the network LED Indicators LED Color Status Description Power Yellow On Power applied Fiber Green Off No signal detect On Signal detect Blink All ones received UTP Coax Green Off No signal detect On Signal detect Blink All ones received Test Green Off Normal operation On L LB or All 1 s Test mode Blink R L LB Received master Fast Blink R L LB Received slave Fiber Cable Specifications Multimode Cable 50 125 62 5 125 100 140 um Wavelength 1310nm Max Distance 5km Singlemode Cable 9 125 um Wavelength 1310nm Max Distance 30km Singlemode long haul Cable 9 125 um Wav
3. Omnitron Systems Technology Inc FlexPoint T1 E1 Copper to Fiber Converters User Instructions Description The FlexPoint T1 E1 connects T1 and E1 devices such as PBXs CSUs and routers via multimode MM or single mode SM fiber Designed to extend the standard T1 E1 twisted pair or Coax network distances over fiber this converter provides protection from environmental noise and effectively increases high speed network reliability The following models are described here Model Fiber Type Max Distance 4470 90 x MM SC 1310nm 5km 4471 91 x SM SC 1310nm 30km 4472 92 x MM ST 1810nm 5km 4473 93 x SM ST 13810nm 30km 4474 94 x SM SC 1310nm LH 60km Power Options x 0 No power adapter included chassis module 1 110 Volt 60 Hz 2 110 230 Volt 50 Hz Mounting Options 4380 FlexPoint Wall Mounting Hardware Kit 4384 FlexPoint 18 to 72VDC Stand Alone Power Supply 4381 FlexPoint DC Converter Wall Mounting Kit for 4384 4385 FlexPoint 14 Unit48VDC Power Redundant Chassis 4392 FlexPoint 5 Unit Rack Mounting Shelf 4395 FlexPoint 14 Unit AC Power Redundant Chassis Local loop back and Remote loop back When both Local and Remote Loop back are set to the Normal position the FlexPoint T1 E1 uses the default B8ZS data format When both switches are turned to their On position it uses the AMI data format Transmit force 1 s to fiber This switch is used to insert an all ones pattern into the dat
4. a stream being transmitted out of the fiber port on the FlexPoint T1 E1 converter Data being received on the coax or twisted pair will be disabled and data being received on the fiber is passed through to the coax or twisted pair side By returning the switch to the normal position the unit will resume to normal operation Transmitforce 1 s to Coax or UTP This switch is used to insert an all ones pattern into the data stream being transmitted out of the coax or twisted pair on the FlexPoint T1 E1 converter Data being received on the fiber will be disabled and data being received on the coax or twisted pair is passed through to the fiber side By returning the switch to the normal position the unit will resume to normal operation Alarm Relay Contacts The FlexPoint T1 E1 features dry relay contacts for optionally connecting the it into a separate T1 E1 alarm circuit The relay closes when a loss of power or when signal detect is lost to the copper or fiber connection RJ 45 RJ 48 Relay o n Operational rating on relay pins 3 amp 6 0 220VDC max 2A Power Adapter Notice 1 When Using in a stand alone configuration this product is intended to be and must be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp 2 This product should always be used only with Omnitron Supplied Power Unit model numbers 9113 PS or 9115 PS WARNING
5. e or operating outside the environmental specification of the product including but not limited to voltage ambient temperature radiation unusual dust etc or improper site preparation or maintenance No other warranty is expressed or implied Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose Exclusive Remedies The remedies provided herein are the Buyer s sole and exclusive remedies Omnitron shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any legal theory Form 040 04470 002D 11 07 User Warranty Registration Please register on line http www omnitron systems com or complete both sides and mail or fax this registration form to User Warranty Registration Please register on line at http www omnitron systems com or complete both sides 140 Technology Drive 500 Irvine CA 92618 USA Omnitron Systems Technology Inc Fax 949 250 6514 and return this form to Omnitron Systems Model Purchase Date Serial Number Name Purchased From Address City Company Address Zip Code State Country Zip Code State City Comments and Suggestions Country Phone E mail Fax Please complete both sides of this form Please complete both sides of this form
6. elength 1310nm Max Distance 60km equipment The twisted pair connection requires two active pairs in a T1 E1 environment The active pairs are pins 1 amp 2 and pins 4 amp 5 Only dedicated wire pairs should be used for the active pins Set the UTP DCE DTE switch for the RJ 45 48 port to the appropriate setting Note Use copper cables that are compliant with the specifications that are outlined in copper cable specifications Coax E1 Connector Attach the BNC to the FlexPoint T1 E1 converter and attach the other end of the BNC to the network equipment Note Use copper cables that are compliant with the specifications that are outlined in copper cable specifications Switch Settings UTP DCE DTE setting The UTP DCE DTE switch is used to eliminate the need for crossover and custom cables to connect devices together when using the RJ 45 48 port Set this switch to DCE to use a straight through cable and to DTE when a crossover cable would be required DCE DTE Twisted 1 RTIP TTIP Pair 1 2 RRING TRING Twisted 4 TTIP RTIP Pair 2 5 TRING RRING Twisted 1 RTIP TTP Pair 1 2 RRING TRING Twisted 4 TTIP RTIP Pair 2 5 TRING RRING T1 E1 Copper line configuration settings The T1 E1 copper line codes and line lengths are configured using dip switches located on the side of the FlexPoint T1 E1 media converter Copper Cable Specif
7. ications Twisted Pair cable for T1 Gauge 22 to 24 AWG Impedance 100 Q 10 Impedance characteristic 2 6 dB 100m 1 0 MHz Maximum distance 6 000 ft Twisted Pair cable for E1 Gauge 22 to 24 AWG Impedance 120 Q 10 Impedance characteristic 2 6 dB 100m 1 0 MHz Maximum distance 8 000 ft Coax cable for E1 Gauge 22 to 24 AWG Impedance 75 Q 10 Impedance characteristic 2 dB 100m 1 0 MHz Maximum distance 8 000 ft For product specifications refer to the product data sheet Technical Support For help with this product contact our Tech Support Phone 949 250 6510 Fax 949 250 6514 Address Omnitron Systems Technology Inc 140 Technology Drive 500 Irvine CA 92618 USA E mail support omnitron systems com URL http www omnitron systems com Line Type Port Type Distances Switch Positions 1 2 3 4 T1 DSX 1 RJ 45 48 0 133 rn r T1 DSX 1 RJ 45 48 133 2665 4 4 4 1 T1 DSX 1 RJ 45 48 266 39 4 4 f 4 T1 DSX 1 RJ 45 48 399 533 4 4 T 1 T1 DSX 1 RJ 45 48 533 655 4 T 4 4 T1 DS 1 RJ 45 48 OdB E E T1 DS 1 RJ 45 48 7 5 dB 41T UT T1 DS 1 RJ 45 48 15 0 dB T s T1 DS 1 RJ 45 48 22 5 dB TTT E175Q Coax BNC Standard T 4 4 E1120Q RJ 45 48 Standarda TFT 4 YT E175Q Coax BNC Extended T Jb fT 4 E1120Q RJ 45 48 Extended T LT T Operational switch settings and functions The following operational switches located on the front of the FlexPoint T1 E1 converter are to assist in installation and fault isolation
8. oop back L LB This switch will set the FlexPoint T1 E1 converter in a loop back mode on both the fiber and copper connections By returning the switch to the normal position the unit will resume to normal operation Loopback Enabled Remote loop back R L LB This switch will allow the entire fiber segment to be tested at either of the FlexPoint T1 E1 converters without having to set switches on both units When set in this mode the local unit is switched to a local loop back mode The fiber Tx port will be further encoded to carry a remote loop back protocol This remote loop back will set the far end FlexPoint T1 E1 converter to remote loop back mode and return a signal to the sending unit An LED on the local and remote FlexPoint T1 E1 converters will show a confirmation that the fiber segment is communicating properly between devices By returning the switch to the normal position it will return to normal operation Cu Rx FO Tx FO Rx Cu Tx B a a lt _______ _ _ lt Cu Tx FO Rx FO Tx Cu Rx Remote Loop Request Over Fiber Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate use and or maintenance of the equipment by Buyer Buyer supplied equipment Buyer supplied interfacing unauthorized modifications or tampering with equipment including removal of equipment cover by personnel not specifically authorized and certified by Omnitron or misus
Download Pdf Manuals
Related Search