Omnitron FlexPoint Gx
Contents
1. 949 250 6514 2 S3 O you are qualified and certified to do so by Omnitron modifications or tampering with equipment including Readies r o e oe T one n gt D L Systems Technology Inc removal of equipment cover by personnel not specifically FESS MAON SYSTEMS HeCnNOlOgy WIC G J 2d l authorized and certified by Omnitron or misuse or 27 Mauchly 201 D a Caution operating outside the environmental specification of the Irvine CA 92618 USA S 2 All user required operations can be performed without product including but not limited to voltage ambient E mail support omnitron systems com 2 a coe opening unit bie olla to open or remove the temperature radiation unusual dust etc or improper URL http www omnitron systems com O se cover or tamper wi e unit site preparation or maintenance DM 3 S S Warranty No other warranty is expressed or implied Omnitron T 5 3 5 This product is warranted to the original purchaser against specifically disclaims the implied warranties of a 32 defects in material and workmanship for a period of TWO merchantability and fitness for any particular purpose z 3 3 YEARS from the date of shipment A LIFETIME warranty Exclusive Remedies D O gt may be obtained by the original purchaser by REGISTERING The remedies provided herein are the Buyer s sole and gt ua S lt H this product with Omnitron within 90 days from the date of exclusive remedies Omnitron shall not be liab2. COST Omnitron Systems Technology Inc FlexPoint Gx User Instructions Description The FlexPoint Gx converts between Gigabit Ethernet fiber 1000Base X Sx Lx and 1000Base T twisted pair RJ45 UTP cabling The following multimode MM and single mode SM models are described here Model Fiber Type MaxDistance Type 4370 850 nm MM 220 m 720 ft SC 4371 1310 nm SM 10 km 6 2 mi SC 4372 1310 nm SM 25 km 15 5 mi SC 4373 1550nm SM 65 km 40 4 mi SC 4670 850nm MM 220 m 720 ft MT RJ 4671 1310nm SM 10 km 6 2 mi MT RJ 4673 1310nm SM 10 km 6 2 mi LG 4674 1310 nm SM 25 km 15 5 mi LC 4675 1550nm SM 65 km 40 4 mi LC Power Adapter Notice 1 When using in a stand alone configuration this product is intended to be and must be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp 2 This product should only be used only with Omnitron Supplied Power Unit model number 9113 PS WARNING Before inserting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source Mounting and Cable Attachment The FlexPoint Gx can be stand alone mounted using a wall mounting kit model 4380 It can also be rack mounted using a 5 position shelf Model 4392 or a high density 14 unit FlexPoint Powered Chassis AC powered model 4395 or 48VDC powered model 4385 Attach the FlexPoint Gx UTP via a category 5 or higher
3. cable to a 1000Base T Ethernet device Attach the FlexPoint Gx fiber via a single mode or multimode as needed cable to a 1000Base X Gigabit Ethernet device make sure to use the correct wavelegth source for the model being used The FlexPoint transmit Tx must attach to the receive side on other device the receive Rx must attach to the transmit Switch Settings Auto Negotiation Switch Setting the switch to Enable factory setting enables the UTP port to determine the duplex and pause modes automatically Setting the switch to Disable causes the mode of the Duplex and Pause switches to be advertised to the connected device The recommended mode is Enable factory setting Full Duplex Half Duplex Switch This switch controls the half full duplex advertising of the FlexPoint Gx preferred mode of operation when the Auto Negotiation switch is in the Disable position The recommended mode is Full duplex factory setting Pause Switch This switch controls the Pause advertising of the FlexPoint Gx preferred mode of operation when the Auto Negotiation switch is in the Disable position The recommended mode is Enable factory setting Link Isolate Link Propagate Switch When set to the Link Prop factory setting the link state is propagated from the UTP port to the fiber port and visa versa This allows the loss of link to be propagated and
4. detected by SNMP or other network managed devices and it facilitates Spanning Tree network reconfiguration during a cable failure When set to Link Isolate the generation and detection of link presence is done at each point to point segment It should be noted that when in Link Prop mode the absence of received UTP link causes the transmitted fiber link to be turned off The absence of received fiber link causes both the transmit and receive UTP link to be turned off This mechanism prevents a deadly embrace when both links are absent initially during power up and configuration LED Indicators LED Color Description Power Yellow Power applied FDX HDX Yellow On Full Duplex Off Half Duplex Fiber Link Data Received UTP Link Data Received F O Link Rx Green UTP Link Rx Green SEOs IPS FT Ge Warning Limitation of Warranty 3 5 gt S SpE 3 P The operating description in this Instruction Manual is The foregoing warranty shall not apply to defects Technical Support o lt ne 7 amp Ba for use by qualified personnel only To avoid electrical resulting from improper or inadequate use and or For help with this product contact our Tech Support a es ar ge shock do not perform any servicing of this unit other maintenance of the equipment by Buyer Buyer supplied Phone 949 250 6510 D m amp So than that contained in the operating instructions unless equipment Buyer supplied interfacing unauthorized Fax l
5. le for any Q N S D D 3 shipment TO REGISTER COMPLETEAND MAILOR FAX direct indirect special incidental or consequential z oC O S 7 THE REGISTRATION PORTION OF THIS INSTRUCTION damages whether based on contract tort or any legal so O o 0 MANUAL TO THE INDICATED ADDRESS Or you may theory Q S register your product on the internet at http g x e www omnitron systems com During the warranty period Q Omnitron will at its option repair or replace a product which 2 E is proven to be defective p D For warranty service the product must be sent to an Omnitron 2 gt designated facility at Buyer s expense Omnitron will pay the shipping charge to return the product to Buyer s A o designated US address using Omnitron s standard shipping D method Zip Code Please complete both sides of this form Fax User Warranty Registration State Please register on line http www omnitron systems com or complete both sides and mail or fax this registration form to Omnitron Systems Technology Inc 27 Mauchly 201 Irvine CA 92618 USA Fax 949 250 6514 Name Company Address City Country Phone E mail Form 040 04370 001 B 10 03
Download Pdf Manuals
Related Search