Premier CTM-VESA flat panel wall mount
Contents
1. Page 8 CTM VESA Technical Specifications 8 F7 _ B J C Ak 9 Ed mm O 5 TH O O O CP 9 Q O bs O O o 6 S e o Rm 40 5 MOUNTING BRACKET T 9 a A 2 gt m Figure 9 Technical Specifications Page 9 Installation Manual gt CTM VESA Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship Premier Mounts is not liable for improper installation that results in damage to mounts adapters display equipment or personal injury DISCLAIMER OF WARRANTY THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Contact Premier Mounts In the event of missing and or damage equipment or technical questions the following information can help in the completion of the installation Customer Service 800 368 9700 Technical Support techsupport mounts com Notes NORTH AMERICA EUROPE ASIA 3130 East Miraloma Avenue Sw2. D PREMIER BA MOUNTS The original holding company INSTALLATION MANUAL CTM VESA Premier Mounts 3130 E Miraloma Avenue Anaheim CA 92806 Phone 800 368 9700 Fax 800 832 4888 mounts mounts com www mounts com IN CTMVESA R2 CTM VESA k Table of Contents 3 PAR LL 4 INSTALLATION TOOLS sereen sE 4 THREAD DEPTH 5 CTM VESA INSTALLATION 85 2 22 2 2 0 0000000000000000000000 6 TECHNICAL SPECIFICATIONS 9 WARRANT 10 CONTACT PREMIER MOUNTS 10 NOP e E MUI UL 10 Installation Manual Page 2 CTM VESA Warning Statements WARNING PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS WARNING THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING 125LBS IF NOT TH
3. display flat against wall with the upper and lower bracket attaching slots slightly higher than the steel receiving rods of the wall plate Figure 7 With the flat panel display reasonable level lower the flat panel display until the bracket receiving slots are fully installed into the upper and lower wall plate steel rods Gently pull the left and right upper edges of the flat panel display to extend the mount to its maximum 12 tilt and install finger tight the two upper arm 6mm safety knobs one on each side of the mounting bracket Figure 7 Installation Manual Page 6 CTM VESA NOTE To remove the display from the wall simply extend the display to its maximum tilt range remove the two 6 mm safety knobs push the display back to its flat wall position and lift the unit up and out from the wall 15 Once the display on wall installation is complete you can still move the display from left to right or right to left to optimize the final position of the display on the wall by gently sliding the unit on the steel rods of the wall plate This adjustment distance will vary depending on the display model being installed Figure 8 Depending on Display 4 x 12mm Phillips Head Screws Or M6 x 12mm Phillips Head Screws Or M6 x 30mm Phillips Head Screws NOTE The circled letters denote items that specified within the Parts List on Page 5 To determine which mounting hardware to use please refer to th
4. or damage can result from dropping or mishandling the LCD Installation Manual CTM VESA Parts List NOTE This mount is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 Wall Plate Qty 1 D 5 16 x 3 Lag Bolts Qty 6 E M6 x 12mm Safety Knobs Qty 2 G M6 x 12mm Phillips Head Screw Qty 4 B Mount Bracket Qty 1 A 5 16 Flat Washers Qty 6 M4 x 12mm Phillips Head Screw Qty 6 B M6 x 30mm Phillips Head Screw Qty 4 B oon anm on f a aab deoa aa 2S PtP PPP PF FPP sue Ff if f F a p Installation Tools Phillips Head Screw Driver Tape Measure Soft Material Blanket Pencil Level Supplied Thread Depth Indicator Supplied 27 CTM VESA Ea Thread Depth Indicator 1 Insert the thread depth indicator supplied through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it Figure 1 2 Locate the correct diameter screw for the thread insert Compare your marking to the screws supplied If your selected screw is longer than the marking on the thr
5. E WALL STRUCTURE MUST BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH WARNING SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY WARNING PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION oppe Page 3 INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE Indicates that the power plug is to be disconnected from the power outlet Contact Premier Mounts with any questions 800 368 9700 Safety precautions must be taken at all times Warning and Caution statements Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the LCD and or damage to the mounting surface Do not install near a heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the LCD and could increase the risk of fire At least two qualified people should perform the installation procedure Injury and
6. allow House Nakaizumi 607 7 Anaheim CA 92806 USA Shilton Industrial Estate Gunma machi Gunma gun USA and Canada Shilton Coventry England CV79JY Gunma ken 370 3524 Japan Phone 800 368 9700 Phone 44 0 2476 614700 Phone 81 27 371 6998 Fax 800 832 4888 Fax 44 0 2476 614710 Fax 81 27 371 6308 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2006 IN CTMVESA RO Installation Manual Page 10 IN CTMVESA R2
7. at list Depending on the type of display that is used the mounting hardware will vary from manufacturer to manufacturer Page 7 og 5 Jy vorrc722 X gscoonbo23 we evou PPP PARE CPE GARE Mounting Bracket CTM WALL PLATE Figure 4 Figure 5 poo Gerveds PEP CREE PPS CHEE INVERTED LCD von conc Measure and Note Monitor Installation Manual CTM VESA NOTE Arrows on the wall brackets must be facing up prior to installation Secure the lag bolts into the center of the wood stud NOTE The circled letters denote items that specified within the Parts List on Page 5 To determine which mounting hardware to use please refer to that list Depending on the type of display that is used the mounting hardware will vary from manufacturer to manufacturer NOTE When the display brackets receiving slots are fully installed into the upper and lower wall plate steel rods and the plasma is on its flat position there is a 7 8 gap from the top of the rod to the end of the hook This feature is to compensate for tilting Installation Manual Lag Bolt Locations Lag Bolt Locations
8. e distance between the bottom edge of the wall plate and the bottom edge of the flat panel display to determine the correct mounting height of the wall plate EXAMPLE Overall desired height for the bottom outside of the flat panel display is 60 Difference between the bottom edge of the flat panel display and the bottom edge of the wall plate fully installed in the lower receiving slots of the brackets is 4 means the plate bottom outside edge should be placed at 64 from the floor 60 4 64 Determine the desired wall location and its ability to properly support the weight of the flat panel display Figure 5 Locate and mark the 16 wood stud centers closest to the desired flat panel display placement area Measure up from the floor the proper distance to the bottom edge of the wall plate and mark a level reference line on the wall Place the lower portion of the wall plate edge on the reference line and mark the best six 6 each wall plate lag bolt mounting points through the wall plate slots on the wall Drill 1 4 pilot holes on the six marked walls before installing the plate Level the wall plate with the wall plate reference arrow pointing up to the wall using the six 6 5 16 Lag bolts and flat washers supplied Figure 6 With the upper hooks on the flat panel display mounting bracket in the flat on wall position raise the flat panel display with the bracket attached two people minimum recommended and place the flat panel
9. ead depth indicator DO NOT USE this screw 4 screw length must not bypass the marking Select another screw size Figure 2 and 3 until you find one that comes closest to your mark without going past UJ Inverted flat panel display Marking the depth HH BF E B V B T HH EE LF Thread depth indicator Thread insert Figure 1 Screw Thread depth PM Screw Thread depth 774 indicator pP 22 ut N uum ASN v A meu S r E Figure 2 Page 5 Marking Figure 3 Installation Manual CTM VESA CTM VESA Installation Instructions 1 10 11 1 2 13 14 Invert the monitor display and place it on a soft and flat surface Locate the mounting points on the back of the monitor display Remove the floor stand that comes with the plasma monitor if applicable NOTE To determine which hardware to use follow the steps on Page 6 Install the mounting bracket to the plasma monitor and secure by using the appropriate mounting hardware Figure 4 Temporarily slide the round steel rod portion of the wall plate fully into the bottom receiving slots of the installed mounting bracket Measure the distance between the bottom outside edge of the flat panel display and the bottom outside edge of the mounting plate Add the desired bottom edge height of the monitor to th
Download Pdf Manuals
Related Search