Premier FM3 flat panel wall mount
Contents
1. D PREMIER Cad MOUNTS The original holding company INSTALLATION INSTRUCTIONS FM3 61 Universal Flat Panel Mount AUSTRALIA NEW ZEALAND OCEANIA NORTH AMERICA EUROPE DISTRIBUTOR 3130 East Miraloma Avenue Swallow House P O Box 295 Anaheim CA 92806 USA Shilton Industrial Estate Mordialloc Victoria 3195 USA and Canada Shilton Coventry England CV79JY Australia Phone 800 368 9700 Phone 44 0 2476 614700 Phone 039586 6330 Fax 800 832 4888 Fax 44 0 2476 614710 WWW premiermounts com au Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2008 9531 035 001 01 VV lli DE 2 i T Jew 3 ei s IN goo 3 EUER IRIS REO om 6 Mounting Bracket Installation 8 PAA OM 9 TL chini PO Cl ln RTT 10 11 Warning Statements PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING2. Step 2 Mark off six holes to be used for securing the mount and place the wall plate aside Step 3 Next drill holes using an electric drill and masonry bit Step 4 Insert a concrete anchor into each hole Step 5 Use a hammer to lightly tap each anchor into place so that they are flush with the wall Step 6 Once all of the anchors are in place move the wall plate back into position Step 7 Attach nuts and washers to the threaded shafts that are protruding from the wall Step 8 Do not tighten until all nuts and washers are in place Page 6 Installation Manual b 4 FM3 24 Thread Depth Indicator l Insert the thread depth indicator supplied through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it Locate the correct diameter screw for the thread insert Compare your marking to the screws supplied 3 If your selected screw is longer than the marking on the thread depth indicator DO NOT USE this screw 4 The screw length must not bypass the marking Select another screw size until you find one that comes closest to your mark without going past Inverted Flat Panel Display Marking the m HH UILL 7 Thread Insert Thread Depth aE Indicator Figure 1 Screw Marking Screw Marking JU ky II GUA lt ISDA gt Thread Depth Thread Depth Indicator Indicator Figure 2 Figure 3 Installation Manual Page 7 FM
3. OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY IF NOT THE WALL STRUCTURE MUST BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH DO NOT USE THIS MOUNT WITH A DISPLAY WEIGHING IN EXCESS OF 200LBS SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the display If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires or gas lines in wall Cutting drilling into an electrical l
4. State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Installation Manual Page 11
5. for the top row of mounting If the studs are 12 apart use three 3 lag bolts for the top row of mounting points and three 3 lag bolts for the points and two 3 lag bolts for the lower row of mounting points Step 1 Step 2 Step 3 Determine where to mount the FM3 Use all of the studs have been located use Using a 1 4 drill bit drill a pilot hole at a stud finder to find the exact center of a pencil to mark the spots Place the mount the first aligned and marked location each stud against the wall and align the mount to the marked stud locations Step 4 Step 5 Step 6 After the pilot hole has been drilled line Insert one 1 5 16 x 3 lag bolt and With the help of an assistant place a level up the mounting slot opening to the drilled washer into the mounting hole and tighten on the center of the mounting rail and level hole see WARNING below the mount Mark and drill the second mounting hole Insert one 1 5 16 x 3 lag bolt and washer into the mounting hole and tighten see WARNING below Repeat steps 5 and 6 for the remaining mounting points A WARNING Do NOT over tighten lag bolts when attaching the mount to the wall Improper installation may result in personal injury or damage to property Concrete Mounting NOTE Concrete anchors must be used for concrete installation They can be purchased at your local hardware store Step 1 Place the wall plate into position against the wall keeping it level
6. 3 Mounting Bracket Installation To ensure optimal installation this kit includes various screws of different diameters and lengths Step 1 Place your flat panel screen down on a soft flat surface and locate the threaded mounting points that are located on the back of the display NOTE The number of mounting points will vary between manufacturers Step 2 Determine which screw is the correct length by carefully inserting a straw or toothpick and mark how deep the mounting point is please refer to Page 7 for further instructions Step 3 If your display has a curved back or a recessed mounting point a spacer must be used A NOTE Select the spacer that is closest in depth to the recess to keep your bracket as close to the display as possible Step 4 Place the spacer between the mounting bracket and the display Step 5 If a smaller screw is being used M4 M5 or M6 please use a Griplate with each screw for added stability Step 6 Attach each bracket to the display by aligning the holes on each bracket with the threaded inserts on the back panel of your display inserting the screws through both and turning clockwise until they are fully inserted A WARNING Do NOT overtighten the screws MOUNTING HARDWARE un TM ti GRIPLATE MOUNTING BRACKET NYLUN SPACER gt IF APPLICABLE 35 di DISPLAY Page 8 Installation Manual b 4 P2 FM3 k FM3 Installation AN CAUTION Two people
7. 5 5 x 50 M6 x 16 M6 x 20 M6 x 30 M6 x 45 Qty 6 Qty 6 Qty 6 Qty 6 Qty 6 OLLI Qty 6 Qty 6 6 COty 6 Qty 6 Cot 8 20 M8 x 25 M8 x 30 M8 x 35 M8 x 45 M10 x 30 ewe III cow e e Qty 6 Installation Manual Nylon spacers and flat washers FM3 vore The nylon spacers may be stacked to achieve proper spacing 2 Nylon Spacers ii Nylon Spacers Large Qty 8 Oty 6 Nylon Sleeves Qty 8 i Nylon Spacers Large Qty 8 Flat Washers Metal Qty 8 Nylon Spacers Oty 8 Nylon Spacers Small Qty 8 Installation Manual Page 5 b 4 P2 FM3 Wall Plate Installation It is recommended that two people perform the installation One person should hold the mount while the other person A NOTE installs the lag bolt and washer Making sure that the mount is level the person not holding the mount must mark and drill the second mounting hole and secure the second lag bolt and washer lower row mounting points If the studs are 16 18 or 24 apart use two 3 lag bolts
8. are required for this step A WARNING MAKE SURE THE LOCKING SECURITY BRACKET SCREW IS FLUSH WITH THE SECURITY SCREW TAB BEFORE INSTALLATION STEP 2 Step 1 To complete the installation of your new display mount carefully place the flat panel brackets over the upper and lower mounting lips WALL PLATE UPPER MOUNTING LIP LOWER MOUNTING LIP Step 2 Use a Phillips head screwdriver to tighten the two 2 security bracket screws see inset below fa SECURITY TAB N D SECURITY BRACKET SCREV Installation Manual Page 9 Technical Specifications All measurements are In inches mm 45 00 1143 00 178 43 69 eLo 571 50 25 76 654 41 26 0 673 10 7 75 196 85 x 5 127 00 M 1104 4346 Page 10 Installation Manual E or FM3 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you
9. ine or gas lines may cause serious injury Make sure there are no water lines inside the wall where the mount is to be located Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport 2 mounts com Page 2 Installation Manual b N FM3 Parts List NOTE This wall mount is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 Mounting Wall Plate Brackets ED CR Qty 2 5 16 x 3 Lag Bolts wooden studs only Qty 6 5 16 Flat Washers Qty 6 for use with lag bolts GriplateTM Qty 8 Installation Tools Phillips Head Screw Driver Soft Material Blanket 1 2 Socket and Wrench Pencil Tape Measure Drill Gun Thread Depth Indicator Supplied Level Drill Bit Commercially Available Electronic Stud Finder Commercially Available Installation Manual Page 3 M4 x 16 M4 x 25 M5 x 12 5 x 16 5 x 20 5 x 2
10. must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 E Miraloma Ave Anaheim CA 92806 How
Download Pdf Manuals
Related Search