Premier MAG-PRO project mount
Contents
1. Locate the correct diameter screw for the threaded insert If the screw you selected is longer than the 1 8 al allowance mark on the small straw or toothpick Marking the Depth as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Thrsaded insert Test each size of the screws provided The correct screws should thread easily into the mounting point and not pull out when tension is applied Does your projector have multiple mounting points or a single mounting point Lock It Security Hardware Pack Optional Ary N ED The MAG PRO Mount comes with the option of using ae Lock It Security Screws To use the security screws Small Straw simply replace the M6 x 12mm Phillips Pan head screws with the M6 x 12mm security screws Once the hardware has been changed adjust the MAG PRO Mount and tighten the M6 x 12mm security screws using the M5 Security Allen wrench supplied Depth Plus 1 8 Allowance Small Straw Mark or Toothpick or Toothpick If your projector has multiple mounting points proceed to the Multiple Mounting Point Installation section If your projector has a single mount point remove the pre installed mounting legs on the universal projector plate and skip to the Single Mount Point Installation section Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 5 Locate the projector s moun2. CSL1 Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 11 24 MAG PRO MAG PRO W Page 12 Visit the Premier Mounts website at http www mounts com Installation Instructions MAG PRO MAG PRO W 24 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCL
3. Lower the mounting leg by rotating the leveling barrel counter clockwise Raise the mounting legs by rotating the leveling barrel clockwise When the desired position is achieved tighten the mounting screws to the projector and then tighten the hex head leg screws with the M5 Allen wrench Mounting Hardware Too Long WJ The depth of some projector mount points may prevent you from tightening the M2 5 and M3 mounting hardware You can reduce the length of the M2 5 and Mounting Hardware M3 mounting hardware by stacking up toa maximum of five 5 M3 flat washers inside the leveling barrel M3 Washer Avoid stacking too many M3 washers the mounting hardware must thread into the projector mount point at least four 4 complete turns Leveling Barrel Cutaway View Identify the projector s approximate front to back center of gravity Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from front to back Mentally note the apparent center of gravity Identify the projector s approximate side to side center of gravity Place your hands on the front and GS Side to Side back of the projector and gently lift it an inch from the CE Center of Gravity s
4. gt D PREMIER C4 MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Polaris Universal Projector Mount Model MAG PRO MAG PRO W NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 Fax 1 800 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9530 001 031 0B P MAG PRO MAG PRO W Wee lg ht LiM a a a a a A a ae a a A aE e E RERE 2 Warning Statements ia lt 2 sissies sbecersaanadlensisanaudelsaqaccaaeuvadaadaenshignccaeusdaadvecuaasdvaddeeasanacauesssnnivaade E E EE NANEN 2 STAN AION Tool Sree OOA O caesuyhdedhaniptondeytaummucecnnad 3 Parte Eiaeia E E O O a a o AT 3 FEJO Senn E O E E Goaenee denrect eadpulece eed caadern thaudaetcaunddeaensandeeale raat 4 Attaching the MAG PRO MAG PRO W Mount to the Projector 20 0 0 cccccceeeeeetee eee ettteeeeeeenneeeeeeeaeeeeeeeieeeeeeeeieeeeeeeaas 5 Attaching the Projector Plate erenn aN O 5 selecting the Mounting HARAWAle s iaci R O T ascot ase 5 Multiple Mounting Point Installation sessnnenicsini an a AE O 6 Sihle Mounting Point Installations eessen A O O cedinaeaeeenecee 9 Installing the MAG PRO MAG PRO W MouN 00 00 cee intr int rn ee nee r ARTA E 9 MAG PRO MAG PRO W Mount AdjUStMent sisson eee eeee eee e teeta E 11 Securing
5. notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Installation Instructions Visit the Premier Mounts website at http www mounts com Page 13
6. the Premier Mounts website at http Avww mounts com Page 9 gt E MAG PRO MAG PRO W Secure the MAG PRO MAG PRO W by tightening the set screw with the M3 security Allen wrench supplied Route any cables up through the 1 12 NPT and into the ceiling structure If the PP FCTA Ceiling Mount is to be used the CLS must first be threaded into the MAG PRO MAG PRO W For further installation lee ie i please refer to the PP FCTA installation Set Screw manual M3 Security Wrench Slowly raise the projector toward the upper assembly Once the projector is close to the upper assembly MagnaGuide Technology will pull the lower assembly into the upper assembly and the locking tab will engage THE MAGNETS ARE USED FOR GUIDING THE UNIT ONLY PLEASE MAKE SURE THE TWO 2 M4 X 12MM SCREWS ARE USED TO SECURE THE PROJECTOR M4 x 12mm Security Screw Attach the two 2 M4 x 12mm security screws and star washers that are located on each side of the locking tab Do not release your hold on the projector until the upper and lower assemblies are engaged and the locking tab is in place Proceed to the MAG PRO MAG PRO W Mount Adjustment section Page 10 Visit the Premier Mounts website at http Avww mounts com Installation Instructions MAG PRO MAG PRO W 24 MAG PRO MAG PRO W Mount Adjustment After the projector has been installed you may need to adjust it To adjust the projector Loose
7. H USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the projector If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http Avww mounts com Installation Instructions gt 4 MAG PRO MAG PRO W 24 Installation Tools The following tools may be required depending upon your particular installation They are not included EA Tape Measure Phillips Tip Screw
8. UDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Disclaimer Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without
9. driver Pencil Protective Eyewear M3 Security Wrench i M5 Security Wrench Supplied Supplied Ladder Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 MAG PRO MAG PRO W Mount Hardware MAG PRO MAG PRO W Mount Qty 1 Barrel Cap Star Washers Qty 4 Qty 2 M3 Flat Washer 14 20 x 5 16 Screw M4 x 12mm Screw M5 x 12mm Screw M6 x 12mm Screw Qty 4 Qty 1 Qty 6 Qty 4 Qty 4 Installation Instructions Visit the Premier Mounts website at http Avww mounts com Page 3 gt 4 a MAG PRO MAG PRO W Congratulations on the purchase of your new Premier Mounts Polaris Universal Projector Mount Your MAG PRO MAG PRO W Mount may be secured to a1 2 NPT The Polaris features our exclusive MagnaGuide Technology which assists the installer for quicker installation times and peace of mind Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and tools you need to safely complete the installation In addition some steps of this installation may require two people to prevent personal injury and or damage to your projector Please observe all warnings in the f
10. n the M5 set screw using the M5 Allen wrench both sides Adjust the projector to the correct position Firmly grasp the projector in both hands and tilt either forward or backward to adjust the level OR 4 M5 Set Screw Firmly grasp the projector in both hands and rotate side to side for orientation adjustment Tighten both M5 set screws using the M5 Allen wrench Securing the MAG PRO MAG PRO W Projector Your MAG PRO MAG PRO W Projector Mount includes one pre installed Security Leveling Barrel in a mounting leg which can provide additional theft deterrence for your projector when used with a padlock or PCB CSL1 Security Cable Shown below is an example of how you can route a PCB CSL1 through the Security Barrel The Security Cable is routed through the Security Barrel after the standard leveling barrel is replaced by the Security Barrel and the projector mount is securely attached to the projector as per the installation instructions The PCB CSL1 kit also includes a Cable Looper which you can use to create a tight loop for cable management The PCB CSL1 kit which contains one 1 18 braided cable one 1 chassis sleeve one 1 cable looper one 1 cylinder lock and two 2 cylinder lock keys is sold separately Additional cylinder locks additional Security Barrels and longer cables are also sold separately Padlock Combination or Keyed PCB
11. ollowing installation procedure and utilize proper safety equipment at all times Cable Routing Discretely manage cables through mount and into ceiling MagnaGuide Technology Powerful magnets assist installation and guide the projector plate into the ceiling mount Lock It Security Hardware Security hardware deters tampering Adjustable Leveling Barrels You can quickly level the mounting legs without any specialized tools Radial Glide Up to 6 of adjustment in any direction Security Leveling Barrel Allows the user to easily secure the mount with a padlock Page 4 Visit the Premier Mounts website at http Avww mounts com Installation Instructions MAG PRO MAG PRO W 24 Attaching the MAG PRO MAG PRO W Mount to the Projector Locate the mounting points on the bottom of the projector see arrows to the right Proceed to the Attaching the Projector Plate section Attaching the Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark
12. ot overtighten the M6 x 12mm screws Insert one 1 Barrel Cap into the end of each leveling barrel except the security leveling barrel Page 8 Visit the Premier Mounts website at http Avww mounts com Installation Instructions MAG PRO MAG PRO W 24 Single Mounting Point Installation A single 14 20 x 5 16 screw must be used to attach the Projector Plate to the projector if your projector has only one mounting point A Do not overtighten the 20 x 5 16 screw Proceed to the Installing the MAG PRO MAG PRO W Mount section Installing the MAG PRO MAG PRO W Mount The Polaris MAG PRO MAG PRO W may be attached to 1 12 standard threaded pipe NPT or N 1 2 standard threaded one of Premier Mounts adjustable height ceiling pipe NPT adapters Please refer to the installation instructions S that come with these adapters Lift the MAG PRO MAG PRO W up to the preinstalled 1 12 NPT or any of Premier Mounts compatible adapters Thread the MAG PRO MAG PRO W onto the length of 1 2 NPT or any of Premier Mounts compatible adapters When attaching the MAG PRO MAG PRO W to the pipe please ensure that the MAG PRO MAG PRO W is threaded on at least four 4 complete turns If you are having difficulty achieving four complete turns insert a screwdriver through the access hole and apply pressure while turning the MAG PRO MAG PRO W see below Four complete turns Installation Instructions Visit
13. the MAG PRO MAG PRO W Projector rosserie enr EEEE A EAEE 11 Technical Specifications ma sinsisnaniereniinena ienaa a E E E N 12 EE 0 1 E E E E A E E A cere renee rere A E E E 13 DISCIAIN A A I E E T E O ee ea el beanie E E A O AT E A O T T 13 Weight Limit THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Maximum Projector Weight 2 5 bs THE PROJECTOR IF NOT THE CEILING STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE TOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR INANY MANNER RELATING TO ANY SUC
14. ting points Position an appropriate number of mounting legs on the projector The four mounting legs come pre installed If there are less than four thread inserts on the projector remove the appropriate number of mounting legs The number and placement of mounting points on projectors varies between projector manufacturers Refer to you projector s technical specifications for the number and location of the mounting points on your specific projector Only attach to the projector manufacturer s specified mounting points on the projector chasis with a minimum of three mounting legs Please follow all safety instructions specified by the projector manufacturer as well as the safety instructions outlined in this manual Attach the appropriate number of mounting legs to the projector using the corresponding mounting hardware A Do not tighten the mounting hardware at this time Page 6 Visit the Premier Mounts website at http Avww mounts com MAG PRO MAG PRO W Installation Instructions d MAG PRO MAG PRO W a If the mounting legs need to be leveled rotate the leveling barrels to level the mounting bracket To raise the mounting legs rotate the leveling barrel clock wise To lower the mounting leg rotate the leveling barrel counter clock wise _ Raise or lower each of the mounting legs by UU rotating the leveling barrels until all of the mounting legs are at an equal height
15. urface on which it is resting Carefully adjust your J grip on the projector until it seems balanced from side to side Mentally note the apparent center of gravity Place the Universal Projector Plate if not already attached on top of the mounting legs with the center hole as close as possible to the projector s center of gravity Front to Back Center of Gravity Installation Instructions Visit the Premier Mounts website at http Awww mounts com Page 7 gt P MAG PRO MAG PRO W Position the legs accordingly for best configuration lt ae 0 You may raise or lower each leg independently by Sliding M6 turning the leveling barrels Square Nut Secure the legs to the projector plate by screwing M6 x 12mm security screws into the M6 square nut do not overtighten on the mounting legs Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the Projector Plate If the M6 square nut is not aligned with any slot you UJ can use any thin tool such as a toothpick to nudge it into alignment Tighten the mounting screws which secure the mounting legs to the projector Do not overtighten the mounting screws Attach the Projector Plate to each of the mounting legs by inserting and tightening one 1 M6 x 12mm screw through the Projector Plate into the M6 square nut on each of the mounting legs A Do n
Download Pdf Manuals
Related Search