Chief KSA1018B flat panel wall mount
Contents
1. Drywall 1 2 minimum Drywall Thickness Both Sides of Stud Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 362 S 125 18 C Shaped S Stud Section Figure 1 Installation Instructions FSA1018 Preparation of Existing Mount If mount has previously been installed 1 Remove display from mount following instructions provided with mount 2 Remove mount from wall following instructions provided with mount 3 Proceed to step 4 If mount has not previously been installed 4 Remove mount wall plate from swing arm assembly by removing screw washers and spacers pivot pin and locknut See Figure 2 Screw Swing Arm Washers Pivot Pin Existing Wall Plate Locknut NOTE Wall plate and hardware removed is not required for steel stud installation It may be discarded or kept for future use in a non steel stud application Assemble Swing Arm to Steel Stud Wall Plate To assemble the mount 1 Orient swing arm so that it is positioned in front of mounting tabs on wall plate A See Figure 3 Slide inner stud C up into bottom of swing arm Place spacer G up against bottom of swing arm and hold spacer G and inner stud C in place See Figure 3 4 Slide swingarm with inner stud C and spacer G between mou2. Serrez les fixations WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this kit is attached can support five times the combined weight of all equipment WARNING This kit is intended for use only with Chief FWD FWS and FWG Swing Arm Wall mounts WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 40 Ibs 18 1 kg Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fe
3. YinDu International Building 4 000347 RevC 2 Milestone AV Technologies iR Shenzhen CHINIA P 86 755 8996 9226 06 08 486 755 8996 9217
4. with flange of plastic cap See Figure 7 10 Repeat steps 6 through 9 for each mounting hole 6 Hold metal channel on anchor M flat alongside plastic strapsandslidechannelthroughhole SeeFigure5 Installation Instructions FSA1018 Steel Stud Drywall Plastic Cap Plastic Straps Anchor Metal Channel SIDE VIEW Figure 7 11 Place mount over anchors and align mounting holes in display mount with holes in anchors See Figure 8 12 Place flat washer K onto button head capscrew L 13 Insert Phillips pan head capscrews L with flat washer K through mounting hole in display mount and into anchor M and tighten until flush against mount DO NOT overtighten WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware Steel Stud Drywall Display Mount Anchor Metal Channel SIDE VIEW Figure 8 FSA1018 Installation Instructions e USA International A 8401 Eagle Creek Parkway Savage MN 55378 IA CH E 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Our Mounts Your Vision Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands Chief Manufacturing a division of P 31 0 40 2668620 Milestone AV Technologies Inc F 31 0 40 2668615 Asia Pacific A Room 24F Block D Lily
5. INSTALLATION INSTRUCTIONS F Series Steel Stud Installation Kit CHIEF FSA1018 Our Mounts Your Vision FSA1018 Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien
6. ndas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Installation Instructions FSA1018 TOOLS REQUIRED FOR INSTALLATION AND PARTS m 22222 g Lj D 1 2 013mm 3 16 I M 1 1 B 1 lt gt C 1 j D 1 e amp 1 e F 1 K 3 1 4 20 L 3 e G 1 1 4 20 X 1 3 4 O 2 1 4 20 SNAPTOGGLE BB H 1 1 4 20 B 1 3 16 FSA1018 Installation Instructions Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum reguirements for installation of display mounts onto a Steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud Display Mount Installation Location Must be centered on stud If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center N There must be a minimum of 1 7 8 48mm clearance inside wall
7. nting tabs in wall plate A See Figure 3 Slide stepped spacer D spacer E and washer F onto flat head cap screw B See Figure 3 Slide flat head capscrew B with spacers E and washer F down into swing arm and through inner stud C and lower spacer G See Figure 3 Secure swing arm to mount using Nylock nut H See Figure 3 Figure 3 Mount Installation After determining the site meets the installation requirements FSA1018 Installation Instructions Drywall 1 Identify desired mounting location on wall 2 Using a stud finder or similar method locate studs EM 3 Align mounting holes in mount with studs making sure mounting holes are centered on studs Plastic Straps 4 Mark location of three mounting holes on wall See Figure 4 5 Drill three 1 2 13mm holes See Figure 4 1 2 013 x3 Figure 5 7 Holding plastic straps on anchor M pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud as show in figues below See Figure 6 8 Slide plastic cap on anchor M towards wall until flange of cap is flush with wall See Figure 6 Steel Stud Drywall Plastic Cap M x3 Anchor Metal Channel Mounting holes centered on SIDE VIEW studs Figure 6 Figure 4 9 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level
Download Pdf Manuals
Related Search