Chief KTA325B
Contents
1. Square Nut End Lock Centris Head Figure 7 Slide Centris Bracket off Array Rail Place display face down on a clean dry surface 4 Place four 3 8 or 3 4 nylon spacers 60 or 70 over four mounting holes in display back NOTE Refer to Table 1 to select the applicable screw and spacer combination 5 Align Centris head mounting holes with four nylon spacers 6 Secure Centris head to display using four M4 x 20mm Phillips pan head screws 40 or four M4 x 30mm Phillips pan head screws 50 See Figure 8 Models KTA 220 225 and KTA 320 325 Phillips Pan Head Screw 40 or 50 Centris Head Display Figure 8 Mount Centris Bracket to Display 7 Slide display with Centris bracket onto mounting rail See Figure 9 NOTE Repeat previous steps for each additional display 8 Install end locks into mounting rail using the 5 32 hex key 80 See Figure 10 Display with Centris Bracket O Array Rail a TN SJ Figure 9 Mount Display with Centris Bracket to Array Rail Models KTA 220 225 and KTA 320 325 End Lock Retaining Screw Centris Head Figure 10 Install End Lock s Display Adjustment These pivot arrays allow horizontal pitch roll and yaw adjustment of each display with a maximum pitch range of 15 up and 15 down These pivot arrays also allow a full 360 deg of display roll Display Horizontal Position Adjustment To adjust displ2. 0 and KTA 225 or 30 lbs 13 6 kg for the KTA 320 and KTA 325 CAUTION Check the unit for shipping damage before you begin the installation CONTENTS IMPORTANT WARNINGS AND CAUTIONS 2 TOOLS REQUIRED FOR INSTALLATION 3 Pan Sha eects aces a el en eee ate ee 3 INSTALLATION GG 2 2 4 Display IHstallalon zn ae eee eee 4 Attach Centris Head to Flush Mount Display 4 Attach Centris Head to Recessed Mount Display 5 ADJUSTMENTS er ts ren 6 Array Adjustment sea 6 Display AdjUStMeNt ooocccnccccccconcncnncnncnoncnnnnonononcnnnnonnnnnnos 6 Display Horizontal Position Adjustment 6 Display Pitch Roll and Yaw Adjustment 6 Installation Instructions TOOLS REQUIRED FOR INSTALLATION e Phillips screwdriver e 3 16 Hex Key e 5 32 Hex Key NOTE Other tools may be required depending on your method of installation Parts Unpack carton and verify kit contents Read installation instructions completely If any listed parts are missing contact Chief Customer Service Models KTA 220 225 and KTA 320 325 Table 1 Parts a e Tee o rra 1 Quantity varies depending upon the number of displays being mounted Figure 1 PARTS Models KTA 220 225 and KTA 320 325 INSTALLATION 1 Assemble pole clamp back 90 to pole mount front using two FW 110 and two BHCS 100 using a 5 32 hex key See Figure 2 2 Secure pole mount back 90 to po
3. INSTALLATION INSTRUCTIONS Horizontal Array Pole Clamp Models KTA 220 225 and KTA 320 325 The KTA 220 225 and KTA 320 325 pivot arrays allow horizontal yaw vertical pitch and roll display adjustment The pitch adjustment range is 30 15 up 15 down The KTA is designed to mount two or three 17 displays The KTA accommodates standard VESA 75mm 100mm compliant displays KTA 320 325 BEFORE YOU BEGIN CAUTION To prevent damage to your display which could affect or void the Factory warranty thoroughly study all instructions and illustrations before you begin to install the mount Pay particular attention to the Important Warnings and Cautions on Page 2 CAUTION The combined weight of the displays installed must not exceed 70 Ibs 31 8 kg for the KTA 220 and KTA 225 and 90lbs 40 8 kg for the KTA 320 and KTA 325 the maximum load capacity of the mounts The weight of each individual display must not exceed 35 Ibs 15 9 kg for the KTA 220 and KTA 225 or 30 lbs 13 6 kg for the KTA 320 and KTA 325 CHIEF MANUFACTURING INC 8832 000141 Rev E PAS 1 800 582 6480 952 894 6280 FAX 952 894 6918 02008 Chief Manufacturing iC 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com SAVAGE MINNESOTA 55378 USA 11 08 Models KTA 220 225 and KTA 320 325 Installation Instructions e A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow th
4. ay horizontal position 1 Loosen Centris bracket rear adjustment knob See Figure 11 2 Slide Centris bracket with display left or right until properly positioned on array rail 3 Tighten Centris bracket rear adjustment knob Horizontal Adjustment Figure 11 Display Horizontal Adjustment Display Pitch Roll and Yaw Adjustment To adjust display position 1 Loosen Centris bracket front adjustment knob See Figure 12 2 Tilt display up or down or adjust display roll left or right until properly positioned 3 Tighten Centris bracket front adjustment knob Installation Instructions Pitch Roll Adjustment Figure 12 Display Pitch and Roll Adjustment Installation Instructions Models KTA 220 225 and KTA 320 325 u ty FE e
5. e instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING RISK OF ELECTRIC SHOCK Using the wrong screws could result in severe personal injury or damage to your display If your display uses a longer screw size than those included in the kit DO NOT use the screws provided with the kit Use the screws provided with your display or contact the manufacturer WARNING Improper installation can result in serious personal injury Make sure that the mounting surface can support a redundant weight factor five times the total weight of the equipment If not reinforce the mounting surface structural members before installing the mount WARNING Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted WARNING The installer is responsible for verifying that the mounting surface to which the KTA is anchored will safely support the combined load of all attached components or other equipment WARNING Watch for pinch points Do not put your fingers between movable parts WARNING Make sure the mount is correctly oriented WARNING The combined weight of the displays installed must not exceed 70 Ibs 31 8 kg for the KTA 220 and KTA 225 and 90lbs 40 8 kg for the KTA 320 and KTA 325 the maximum load capacity of the mounts The weight of each individual display must not exceed 35 Ibs 15 9 kg for the KTA 22
6. le mount front and pole by tightening two BHCS 100 using a 5 32 hex Key 3 Secure pole mount back to pole mount front and pole by tightening three BHCS using 5 32 hex key Pole Pole Mount front with Array Pole Clamp Back 90 Figure 2 Mount Array on Pole Display Installation Attach Centris Head to Flush Mount Display CAUTION If display uses a screw size other than those included in the kit DO NOT use the screws provided Using the wrong screws could result in damage to your monitor 1 Install two M4 x 12mm Phillips pan head screws 30 into two upper mounting holes in display back See Figure 3 NOTE DO NOT fully tighten at this time 2 Hang display on Centris head See Figure 4 3 Install bottom two M4 x 12mm Phillips pan head screws 30 through Centris head mounting holes and into lower mounting holes in display back 4 Tighten four M4 x 12mm Phillips pan head screws 30 See Figure 5 Installation Instructions M4 x 12mm Phillips Pan Head Screw 30 Figure 5 Secure Display to Centris Bracket Installation Instructions Attach Centris Head to Recessed Mount Display CAUTION If display uses a screw size other than those included in the kit DO NOT use the screws provided Using the wrong screws could result in damage to your monitor 1 Uninstall end lock using the 5 32 hex key 80 See Figure 6 2 Remove Centris head from mounting rail See Figure 7 Centris Head
Download Pdf Manuals
Related Search