Chief MAC720 flat panel floorstand
Contents
1. H 2 3 8 16 x 1 MAC720 Installation Instructions ASSEMBLY AND INSTALLATION WARNING EXCEEDING MAXIMUM WEIGHT CAPACITY MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to ensure the total amount of weight placed on the cart stand does not exceed 125 lbs 56 70 kg for the MFC 125 lbs 56 70 kg for the MF1 and 250 1 5 113 40 kg for the MF2 125 lbs 56 70 kg per faceplate Installing Display s to Cart Stand 1 Install display s to cart or stand following the installation instructions included with the cart stand Assembly for Single Display 1 Attach faceplate A to bracket B using two 3 8 16 x 1 roundhead carriage bolts H two spacers E and two 3 8 16 Nylock lock nuts G See Figure 1 MAC720 must be installed BELOW the knob located on the post back Figure 2 Assembly for Dual Display WARNING TIPPING HAZARD Place MAC720 only on FRONT of MFC and MF1 MAC720 may be placed on both FRONT and BACK of MF2 1 Attach first faceplate A to bracket B using two 3 8 16 x 1 roundhead carriage bolts H two spacers E and two 3 8 16 Nylock lock nuts G See Figure 1 2 Attach second faceplate A to bracket B using two 3 8 16 x 1 roundhead carriage bolts H two spacers E and two 3 8 16and two 3 8 16 Nylock lock nuts G See Figure 3 A Figure 1 2 Secure faceplate2. Room 301 Block Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA Post Code 518112 RAI 45 E 27 KAS 6 ESL E AB DFO 86 755 8996 9226 8996 9236 8996 9220 86 755 8996 9217
3. with bracket to clamp bracket C using four 5 16 18 x 3 4 buttonhead cap screws D See Figure 2 NOTE The faceplate assembly must be attached to the clamp bracket below the knob on the lower part of the cart stand post Figure 3 Installation Instructions MAC720 3 Secure faceplate assemblies with bracket to clamp brackets C onto cart stand post using four 5 16 18 x 3 4 buttonhead cap screws D on EACH assembly See Figure 4 NOTE The faceplate assembly must be attached to the clamp bracket below the knob on the lower part of the cart stand post MAC720 must be installed BELOW the knob located on the post back MF2 shown Figure 4 Attaching Display s 1 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figures 5 and 6 MAC720 must be installed BELOW the knob located on the post back WARNING EACH DISPLAY MAY WEIGH IN EXCESS OF 40 LBS Always use two people and proper lifting techniques when installing or positioning display on stand 2 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes See Figures 5 and 6 WARNING IMPROPER INSTALLATION CAN LEAD TO CA
4. INSTALLATION INSTRUCTIONS Cart and Stand Clamp Head Accessory CHIEF MAC720 MAC720 Installation Instructions DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations WARNING Failure to read thoroughly understand and follow all instructions ca
5. RT STAND OR DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Ensure mounting buttons are completely engaged in mounting holes NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 e e Remove pin 6 and nut and move to lower holes A padlock or bolt may be placed through latch holes Figure 6 3 To adjust location of display on cart stand support display s and carefully loosen four 5 16 18 x 3 4 buttonhead cap screws D on each faceplate assembly 4 Slide display s up on post to desired position and tighten four 5 16 18 x 3 4 buttonhead cap screws D for each faceplate assembly See Figure 2 and 4 5 Refer to the installation instructions provided with the cart stand for further information on Tilting Display Removing Display Cable Management and Cart Stand Maintenance MAC720 Installation Instructions CHIEF 8814 000006 2007 Chief Manufacturing www chiefmfg com 07 07 USA International Europe Asia Pacific T Uu 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 40 2668620 31 0 40 2668615
6. n result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components on the cart stand does not exceed 125 lbs 56 70 kg for the MFC 125 Ibs 56 70 kg for the MF1 and 250 Ibs 113 40 kg for the MF2 125 lbs 56 70 kg per faceplate Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Installation Instructions MAC720 TOOLS REQUIRED FOR INSTALLATION AND PARTS 3 16 Provided D 4 5 16 18 x 3 4
Download Pdf Manuals
Related Search