Chief MWRIW6000B flat panel wall mount
Contents
1. Display Offset Left gt 2 1 2 dA 5 Let Display Offset Right Figure 1 2 Secure swing arm to PAC501 using four button head cap screws C four lock washers D and four flat washers E See Figure 2 Trim Installation To install optional trim 1 Remove paper covering adhesive and affix three tape squares F to inside lower flange of each trim piece B See Figure 3 2 Orient trim pieces B as shown in figure below See Figure 3 3 Remove paper covering adhesive back from tape squares F on trim and press trim B against inner wall of box See Figure 3 Installation Instructions MWRIW Series Display Installation WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT install display in a manner other than that specified by the manufacturer Certain displays may require the use of an interface bracket for proper installation of the display If an interface bracket is not installed or there are any other questions regarding the installation of the display immediately contact a Chief Customer Service representative WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 16 18 1kg ALWAYS use two2. Listed MSBU interface bracket provided with Listed Model MWRIWUB but not shown 4 D 4 5 16 18 5 8 5 16 B 4 2 short SIDES 2 long 4 5 16 1 3 16 MWRIW Series Installation Instructions Installation The following procedure assumes that a Chief Listed Model PAC501 In Wall accessory has previously been installed following the installation instructions provided with the PAC501 If a PAC501 is not installed or there are any other questions regarding the installation of this accessory immediately contact a Chief Customer Service representative WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT deviate from installation instructions provided DO NOT substitute hardware The PAC501 is designed to accommodate up to 5 of right or left display offset This is accomplished by aligning the upper and lower mounting brackets on the MWRIW with either the right hand or left hand mounting holes in the PAC501 See Figure 1 1 Align mounting holes in swing arm UPPER and LOWER mounting brackets with four mounting holes in PAC501 See Figure 1 Upper Mounting Bracket 10 sO 10
3. to secure cables within PAC501 WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points 3 Loosen front and rear cable clamps on top arm See Figure 6 4 Thread cable ties E under cable clamps and secure clamps to top arm See Figure 6 5 Route power audio video cables through the cable channel in top arm See Figure 6 allowing sufficient slack in cables for left right movement of display and swing arm and also swing arm extension and retraction Secure cables to top arm using two cable ties E 7 Repeat steps 1 through 4 for lower arm e WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate From Display Figure 6 Installation Instructions MWRIW Series ADJUSTMENTS Pitch Tension Adjustment To adjust display pitch tension 1 With display installed tighten or loosen two screws one on each side using the 5 32 hex wrench See Figure 7 2 Check for desired tension 3 Repeat Steps 1 and 2 until desired tension is obtained Figure 8 Figure 7 Roll Adjustment The MWRIW allows for the horizontal alignment Roll of the display to be adjusted up to 2 right or left to level the display after installing To adjust Roll 1 Loosen the roll tension adjustment nut loca
4. INSTALLATION INSTRUCTIONS Medium Flat Panel In Wall Swing Arm Mount MWRIW Series Our Mounts Your Vision MWRIW Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to
5. equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 125 16 56 7 kg MWRIW Series contains the following models MWRIW6000B MWRIWUB Installation Instructions MWRIW Series LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations 6 Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio B
6. evestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme MWRIW Series Installation Instructions DIMENSIONS L 762 30 00 381 J RETRACTED DEPTH ie APPROXIMATELY 50 l 1500 12mm 3 85 o o B 254 in E L f 106 T 508 200 2000 787 418 L i UJ 05 o 1254 10 00 o o 8 RETRACTED RETRACTED 17 50 Se EXTENSION I B APPROXIMATELY 22 560mm D qu SS EXTENDED EXTENDED DIMENSIONS MILLIMETERS INCHES 13 25 50 1 00 25 __ h 499 1 0 19 65 550 4 21 65 25 1 00 753 13 29 65 50 j j 25 1 00 804 31 65 PAC501 TRIM DIMENSIONS DIMENSIONS MILLIMETERS INCHES Installation Instructions MWRIW Series TOOLS REQUIRED FOR INSTALLATION AND PARTS 3 16 provided
7. people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate 1 Install Listed interface bracket following the installation instructions provided with the interface bracket 2 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall See Figure 4 3 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figure 4 4 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and click lock mechanism has engaged See Figure 4 and See Figure 5 Figure 4 NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 5 Remove pin and nuts and move to lower holes A padlock or bolt may be placed through latch holes Figure 5 MWRIW Series Installation Instructions Cable Management 1 Attach all cables to display 2 If necessary use cable tie mounts G and cable ties M
8. ss are typically all that is required to achieve desired tension See Figure 10 and See Figure 11 10 DECREASE Figure 11 Installation Instructions MWRIW Series 11 MWRIW Series Installation Instructions USA International Our Mounts Your Vision Europe Chief Manufacturing a products division of Milestone AV Technologies 8805 000244 Rev03 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 02 10 Asia Pacific p TI U gt 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 T d b
9. ted on the back side of the faceplate assembly See Figure 2 Level display NOTE If display will not level slightly loosen top nut as well 3 Tighten roll tension adjustment nut See Figure MWRIW Series Installation Instructions Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by The display must be mounted prior to adjusting swing arm tension 1 Locate the adjustment bar and adjustment wrench L 2 Place adjustment bar K into socket head cap screw located at swing arm pivot point See Figure 9 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 thru 4 until desired tension is achieved NOTE If changing from a smaller display to a larger display it may be necessary to increase swing arm tension Socket Head Cap Screw Figure 9 4 Using the adjustment wrench L turn adjustment bar K clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension Small adjustments of 1 8 turn or le
Download Pdf Manuals
Related Search