Chief PTSU flat panel desk mount
Contents
1. 2 0 Pin in Open position move to Closed position after display is removed A padlock or bolt may be placed through latch holes Figure 6 Figure 5 Adjusting Roll Tension The faceplate provides 2 roll adjustment See Figure 7 Roll adjustment is accomplished by shifting the faceplate right or left 2 Remove bolt or padlock from faceplate if used as needed until the faceplate is level See Figure 6 Removing Display 1 Disconnect all power audio video cables NOTE The pin may have been used as a more permanent locking device If so remove nut and pin and move from the lower holes to the upper holes 3 Pull back on flag on upper mounting hole and press down into Open position See Figure 6 WARNING THE DISPLAY MAY WEIGH IN EXCESS OF 40 LBS EACH Always use two people and proper lifting techniques when installing or positioning display 4 Carefully lift display from mount 5 Lift up on pin and place flag back against faceplate to return it to Closed position See Figure 6 Figure 7 Installation Instructions PTS SERIES NOTE Roll tension is preset If the display does not remain in the desired position perform the following roll tension adjustment procedure 1 Remove display following the Removing Display section 2 Remove four 5 16 18 x 5 8 button head cap screws from back of2. INSTALLATION INSTRUCTIONS Large Flat Panel Display Table Stand CHIEF PTS SERIES PTS SERIES Installation Instructions DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty Itis the installers responsibility to make sure all components properly assembled and installed using the instructions
3. igheidssleutel Cl t te hexagonale Cl de s curit Kreuzschlitzschraubendreher Chave de fendas Phillips lt gt Cacciavite a stella PTS SERIES Installation Instructions TOOLS REQUIRED FOR INSTALLATION e 3 16 1 2 Provided E 1 3 16 F 8 G 4 5 16 18 x 5 8 5 16 18 Installation Instructions PTS SERIES ASSEMBLY AND INSTALLATION Attaching Faceplate Assembly 1 Align mounting holes in faceplate assembly A with holes in post assembly B See Figure 3 WARNING FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE NOTE The faceplate assembly can be placed within a four inch range on the post assembly dependent on size of display TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this component is attached can 2 Attach faceplate assembly to post assembly using four support five times the combined weight of all equipment 5 16 18 x 5 8 button head cap screws F See Figure 3 Reinforce the structure as required before installing the component Attaching Post Assembly to Base Assembly 1 Using four 5 16 18 x 5 8 button head cap screws and four 5 16 18 Nylock nuts G secure post assembly B to base assembly D See Figure 1 Figure 3 Attaching Interface Bracket to Displa
4. on Instructions PTS SERIES LEGEND Pencil Mark Marcar con lapiz Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com l pis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Marquage au crayon Serrez les fixations Aflojar elemento de fijaci n Perforar Befestigungsteil l sen Bohrloch Fazer furo Desapertar fixador Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Destornillador Phillips Ajustar Einstellen Ajustar Regolare Kruiskopschroevendraaier Afstellen Tournevis pointe cruciforme Ajuster Llave de boca Quitar Gabelschl ssel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Cl fourche Retirez A mano Opcional Von Hand Optional Com a m o Opcional A mano Opzionale Met de hand Optie la main En option Security Wrench Hex Head Wrench Llave de cabeza hexagonal OROORO Llave de seguridad Sechskantschl ssel Sicherheitsschl ssel Chave de cabe a sextavada Chave de seguran a Chiave esagonale Chiave di sicurezza Zeskantsleutel Veil
5. post assembly inserted in Step 2 of Attaching Faceplate Assembly section 3 Locate rolltension adjustment nut on back of faceplate See Figure 8 Roll Tension Figure 8 4 Partially loosen or tighten the roll tension adjustment nut as needed 5 Re install the faceplate assembly onto the post assembly following instructions in Attaching Faceplate Assembly section 6 Re mount the display following instructions in Attaching Display to Mount section PTS SERIES Installation Instructions CHIEF 8800 000016 Rev F 2007 Chief Manufacturing www chiefmfg com 07 07 USA International Europe Asia Pacific 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 301 Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA Post Code 518112 PITH Ze E gt BSA SAB an 86 755 8996 9226 8996 9236 8996 9220 486 755 8996 9217
6. provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installers responsibility to make sure the combined weight of all components located between the supporting structure and mount up to and including the display does not exceed 100 Ibs 45 36 kg 581 22 360 50 80 59 Q 14 17 2 0 TO APPROX CENTER OF SCREEN NOTE CUSTOM INTERFACE BRACKET NOT SHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 2 AND 2 IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT MEASUREMENTS IN WEIGHT CAPACITY 100 LBS HEIGHT ADJUSTMENT 4 IN 1 INCREMENTS TILT ROLL 07 2 5 MILLIMETERS INCHES 102 4 00 Le o o 1 ng 70 Installati
7. y 1 Attach interface bracket to display following instructions included with interface bracket kit Attaching Display to Mount Figure 1 1 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting 2 Attach edge trim pieces to the base assembly D See holes in mount See Figures 4 and 5 Figure 2 Figure 4 Figure 2 PTS SERIES Installation Instructions WARNING DISPLAY MAY WEIGH IN EXCESS OF 40 Remove bolt LBS Always use two people and proper lifting techniques or padlock when installing or positioning display on mount if used 2 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes See Fig 4 and 5 WARNING IMPROPER INSTALLATION CAN LEAD TO Pin in DISPLAY FALLING CAUSING SERIOUS PERSONAL Closed INJURY OR DAMAGE TO EQUIPMENT Ensure mounting position buttons are completely engaged in mounting holes SE to pen NOTE Holes are provided in the faceplate for use with a position to padlock or similar locking device if desired In addition remove the pin and nut may be removed from the upper holes display and moved to the lower holes for use as a more permanent locking device See Figure 5 Sek remove pin and nut and move to lower holes
Download Pdf Manuals
Related Search