Chief SL236SP project mount
Contents
1. INSTALLATION INSTRUCTIONS SMART LIFT Electric Ceiling Lift This device complies with part 15 of the FCC rules Operation is subject to the following 2 conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit other than that to which the receiver is connected Consult the dealer or and experienced radio TV technician for help Our Mounts Your Vision SL236 Installation Inst2. SSX ELAN NN lt Mounting ANNIN ZOOM IN Figure 10 CAUTION The lift MUST be installed square and parallel Do NOT stress or bend the lift during installation 2 Use the provided push button B to operate the SL236 up and down ensuring that all clearances are adequate Installing Projector on SL236 NOTE The projector is secured from the top by an SLB bracket a Listed accessory Attach the SLB bracket to the projector following the instructions included with the bracket Press in end tabs on both ends of yaw adjustment bracket and lock into place See Figure 11 3 Remove the yaw adjustment bracket from the SL236 by lifting up See Figure 11 Yaw Adjustment Figure 11 4 Place the yaw adjustment bracket over the studs on the SLB bracket selecting the set of holes that best centers the projector weight See Figure 12 5 Install thumb nuts to secure yaw adjustment bracket to SLB bracket with projector SL236 Installation Instructions 6 Reinstall yaw adjustment bracket with projector to SL236 by setting it in place and releasing tabs at each end of yaw adjustment bracket See Figure 12 SLB Bracket appearance varies Figure 12 Adjustments 1 TRAVEL SHOW ADJUSTMENT CAUTION Do not overadjust exceed maximum travel length To adjust the travel of the lift mechanism insert a Phillips screwdriver into the access
3. 24V AC 6 Extend Retract M OON Ground 10 12V DC 9 ground 3 retract J4 extend deel 1 service Ji3 gound 9 ground radio power Red 1 24V AC relay Black 6 Extend Retract Comm 5 Extend Retract Comm 24V White 2 24V AC Comm 2 24V AC Comm Other Jumper1 amp 5 Low Voltage Wall Switch or Relay Control Up 12 retract Down 11 extend Service Open Close Sequence Show Mode Error Reversing contact between error input and common indicates an error and unit reverses direction Extend Error 14 extend error 8 extend error 15 retract error 7 retract error 13 ground 9 ground Relay Contacts relay closes when unit reaches end of travel Extend Relay a 16 extend relay in 14 extend relay in rom Extend Relay b 117 extend relay oul 2 relayoutcommon Retract Relay a 18 retract relay in 13 retract relay in Retract Relay b 19 retract relay out 12 relay out common Serial N A RS 485 A RS 485 Signal Return Ground Equipment Current Sense INTERNAL WIRING sq pinoys sie6uy pue SIBALIPMBJOS seJM saGiey2 s31 Guipunos6 10 xoq anes uj sjeuiuue Bunaejuoo piony SIEUIUL19 84 0 payono Jo peuoene 9g ueo u u aas ay oj pay Figure 18 NOTE The numbers listed in the SL236 Internal and SL236 External columns refer to the corresponding numbers located where indi
4. 6 Y D j 906 6 1 REMEMBER TO ADD 375 TO 1 00 606 6 9 5 TO 25 4mm TO THE MAX 23 88 9 91 251 7mm OF YOUR PROJ ECTOR 633 5 I 24 94 HEIGHTTO ALLOW FOR THE ROO M THE SLB BRACKET WILL C ONSUM E DIMENSIONS MILLIMETERS INCHES SL236 Installation Instructions INSTALLATION REQUIREMENTS The SL236 has been designed to be mounted recessed into a ceiling Power Requirements The SL236 requires 120VAC 60 Hz and 12 amps power to operate IMPORTANT Installation and maintenance of this product must be completed by a qualified service technician Pre Test Lift before Installation 1 Carefully inspect the SL236 for any shipping damage If any damage is apparent do NOT continue with the installation Instead contact Chief for further instructions 2 Attach supports not provided to the top of lift See Figure 1 Supports Figure 1 3 Suspend the lift at least 3 1 2 ft above a surface from a suitable structure such as saw horses ladders or tables 4 Remove and save two screws holding side electrical cover in place See Figure 2 5 Remove electrical cover See Figure 2 External wiring te rminal Figure 2 6 Place the jumper wire E on the external wiring terminal contacts labeled 2 and 5 and wire the push button assembly B to contacts 1 red and 6 black See Figure 3 NOTE Plug in the SL236 test cord
5. See Figure 2 Place jumper wire E 2 and 5 Wire push button assembly B 1 red 6 black Figure 3 See Figure 2 for location of external wiring terminal See Figure 4 for location of internal wiring terminal Installation Instructions SL236 Internal wiring terminal Some parts not shown for clarity Figure 4 Power Requirements and Wiring The SL236 requires 120VAC 60 Hz and 12 amps power to operate IMPORTANT This product must be grounded If it should malfunction or break down grounding provides a path of least resistance for electric current to reduce the risk of electric shock Grounding Instructions This product is equipped with a test cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances 8 WARNING RISK OF ELECTROCUTION All electrical wiring required for installation should be installed by a qualified electrician WARNING PINCH HAZARD FINGERS OR HANDS BETWEEN MOVING PARTS CAN LEAD TO SEVERE PERSONAL INJURY Keep fingers and hands away from mount when operating Press the push button to test the SL236 while it is still in the pre test position Press when the lift is at its top position and it will move down Press when the lift is at its bottom position and it will move up Press while th
6. resume when the thermal overload resets usually within 3 to 5 minutes 11 SL236 Installation Instructions Connecting to Power Supply IMPORTANT This product must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product WARNING FAILURE TO DISCONNECT AND TERMINATE POWER LEADS PROPERLY MAY RESULT IN w PERSONAL INJURY OR EQUIPMENT DAMAGE Licensed electrician must disconnect and terminate the leads to the power cord receptacle and must hard wire the SL236 to a 12 amp power source 1 Disconnect and remove power inlet from interior junction box 2 Hardwire unit to a 120V 60Hz 12 amp power source NOTE This unit was designed to have conduit run directly into the back of the interior junction box NOTE If installing the SL236 in a drywall ceiling remove the outside terminal block and cover with plate D using four 6 32 x 3 16 Phillips pan head screws G Wiring Options NOTE Refer to the Table 1 Wiring Table and See Figure 18 for information on all wiring options NOTE Refer to Table 2 InternalTerminal Descriptions and See Figure 19 for terminal descriptions functions and wiring options 12 Installation Instructions SL236 Table 1 WIRING TABLE Pushbutton Supplied on some models Momentary SPST Red 1 24V AC 1
7. L236SP housing See Figure 6 5 Secure the threaded rods to the SL236SP with Grade 2 or better 3 8 in jam nuts not provided and washers one of each on inside and one of each on outside not provided Top view of SL236 Insert rods into 3 slots Figure 6 6 Install the SMA 620 to the SL236SP if applicable following instructions included with the kit 7 Insert the ceiling grid edge surrounding the SL236SP into the side channel of the SL236SP See Figure 7 NOTE The side channel of the lift will support the weight of the grid and ceiling tiles Side Channel 0 W Figure 7 CAUTION The lift MUST be installed square and parallel Do NOT stress or bend the lift during installation Ceiling Panel x4 Figure 8 8 Use the provided push button B to operate the SL236SP up and down ensuring that all clearances are adequate 9 Replace surrounding ceiling tile 10 Remove four screws and the ceiling tile retainer from the ceiling panel See Figure 9 Ceiling Panel Ceiling Tile Retainer Figure 9 11 Cut ceiling tile to fit inside ceiling tile retainer including grid pieces if necessary 12 Line up holes in ceiling panel with holes in SL236 13 Re install four screws removed in Step 1 of Installing in a Suspended Ceiling section See Figure 8 14 Install ceili
8. cated in the wiring pictures See Figure 18 13 SL236 Installation Instructions Table 2 INTERNAL TERMINAL DESCRIPTIONS wem uno kenen Jemen _ OO O NUMBER DESCRIPTION WIRING OPTIONS BEER 7c ad MM 1 24 VOLT AC 24 volt AC output Remote Controllers ay COMMON 24 VOLT AC COMMON 24 AC common CO e wiwa 12 VOLT DC amp or used for initiating specific functions Initiates movement if lift is static or stops movement if lift is in motion Direction of travel will be opposite ISOLATED EXTEND RETRACT of last direction of travel Operating range is 5 30 Volts AC or DC Used in conjunction with Extend Retract when using NOT TO BE USED AS GROUND FOR FUNCTION OTHER THAN ISOLATED EXTEND RETRACT an external power source to initiate movement EXTEND RETRACT TERMINAL 5 When control senses voltage unit will extend When 7 ISOLATED VOLTAGE SENSE control senses cessation of voltage unit will retract Operating range is 5 30 Volts AC or DC Used in conjunction with Voltage Sensor when using NOT TO BE USED AS GROUND FOR FUNCTION OTHER THAN ISOLATED VOLTAGE SENSE an external power source to initiate movement VOLTAGE SENSOR TERMINAL 7 Extends unit to maximum limit bypassing normal use travel setting Often used for servicing projectors in sp EXTEND ceiling lifts Feature not available on all models round connected to ground initiating any other function ee ee RETRACT momentarially connec
9. e lift is moving and it will stop e Leave SL236 in the closed position INSTALLING IN CEILING WARNING IMPROPER INSTALLATION CAN LEAD TO LIFT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installers responsibility to make certain the structure to which the lift is being mounted is capable of supporting five times the weight of the lift and all attached equipment Reinforce the structure as required before installing the lift WARNING The following instructions assume a suitable mounting structure and surface exists prior to installation and all power and signal wires and cables have been properly installed Installing in a Suspended Ceiling SL236SP NOTE The SL236SP may be suspended from three 3 8 in 1 diameter x 8 in length minimum Grade 2 or better threaded rods not provided which are secured to a 1 5 8 x 1 5 8 12 ga metal framing channel spanning a maximum of 5 feet not provided by Grade 2 or better 3 8 channel nuts not provided Remove the ceiling panel from bottom of lift by removing the four screws in the ceiling panel bottom See Figure 5 x4 2 3 Figure 5 Install the SMA651 at this time if applicable following instructions included with the kit Cut the ceiling grid to fit the perimeter of the SL236SP SL236 Installation Instructions 4 Place SL236SP onto threaded rods inserting the rods into the three slots on top of the S
10. hole NOTE The access hole may be covered by ceiling tile in the SL236SP model Shorten travel by turning adjustment screw clockwise one or two turns Check for desired travel and repeat as necessary See Figure 13 Lengthen travel by turning the adjustment screw counter clockwise one or two turns Check for desired travel and repeat as necessary See Figure 13 10 Travel adjust access hole Figure 13 FORWARD BACKWARD and PITCH Toshift projector backward or forward or up or down loosen the nuts on each end of the yaw adjustment bracket See Figure 14 Move mounting bracket forward or backward or up or down as required The bracket must be adjusted forward backward equally e Tighten nuts See Figure 14 Figure 14 Installation Instructions SL236 3 YAW Rotation Adjust one or the other side of the yaw adjustment bracket backward or forward by loosening two nuts on each side See Figure 15 Adjust bracket as required Tighten nuts See Figure 15 Figure 15 4 ROLL Horizontal Tilt Shift bracket up or down in the side holes on one side or the other by loosening nuts Adjust and tighten nuts on bracket See Figure 16 Figure 16 Routing Cables CAUTION Do NOT attach cables to lower lifting arms or sides of projector bracket Damage may result when lift is raised 1 Lower SL236 to
11. in Other Environmental Air Space in Accordance with Section 300 22 C of the National Electrical Code When using an electrical mounting system basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT A DANG E R TO REDUCE THE RISK OF ELECTRIC SHOCK 1 Always turn off power at source before cleaning WARNING TO REDUCE THE RISK OF BURNS FIRE ELECTRIC SHOCK OR INJURY TO PERSONS Always turn off power at source before putting on or taking off parts e Use this mounting system only for its intended use as described in these instructions Do NOT use attachments not recommended by the manufacturer Never operate this mounting system if it has a damaged test cord or test plug If it is not working properly during testing return the mounting system to a service center for examination and repair e Keep the test power cord away from heated surfaces e Never operate the mounting system with the air openings blocked Keep the air openings free of lint hair and the like e Never drop or insert any object into any opening Do not use outdoors unless marked for outdoor use Route cords and cables as shown in the installation instructions Todisconnect turn all controls to the off position then turn off power at source A WARN NG RISK OF ELECTRIC SHOCK Connect this mounting system to a properly grounded outlet only See Grounding I
12. ion Requirements 6 Power Requirements 6 Pre test Lift Before Installation 6 Power Requirements And Wiring 7 Grounding Instructions 7 Installing In Ceiling 7 Installation Instructions SL236 DIMENSIONS 520 7 260 4 ard SL 236FD 10 25 gt is i J A 732 8 584 2 28 85 2300 698 5 MAXMUM AVAILABLE PACE FOR 27 50 PROJ EC TOR AND EQUIPMENT HxWxD 9 25 x 20 50 x 22 75 INCHES 235 0 x 520 7 x 577 9mm S y Y lt 635 0 25 00 669 3 gt 65 16 5 26 39 19 1 75 E 280 9 11 06 1 06 26 9 914 4 36 00 MAX DIMENSIONS MILLIMETERS 606 3 INCHES 23 87 SL 236SP 520 7 20 50 260 4 0 25 Am ip i k SBS 719 1 K 4 34 28 31 584 2 23 00 I MAXIMUM AVAILABLE SPACE FOR l PROJ EC TOR AND EQUIPMENT Y Y HxWxD 9 25 x 20 50 x 22 75 INC HES 235 0 x 520 7 x 577 9mm 638 0 65 16 5 t 2 12 TY H 1 06 26 9 LJ ial 311 2 11 12 E 12 25 E E Le 107 27 2 41 10 4 Pp lt kr 914 4 36 00 MAX nre eg Y CURRENT 9 26 235 2 ERES MAX9 91 251 7 jp MIN 7 78 197
13. ng tile and grid by sliding it into the open end of the ceiling tile retainer x4 Installation Instructions SL236 A CAUTION Do NOT allow parts of ceiling tile or grid to protrude from the ceiling panel Ensure that all parts assemble easily when installing ceiling tile into ceiling panel Any protruding parts may cause damage to the lift and or ceiling 15 Re install ceiling tile retainer to ceiling panel and secure with four screws removed in Step 10 See Figure 16 Use the provided push button B to operate the SL236SP up and down ensuring that all clearances are adequate after the ceiling has been finished Installing in a Wood Framework Joists 1 Use 1 4 x 1 minimum Grade 2 lag screws not provided to secure SL236 to the joists or wood framework using the mounting tabs located on the sides of the SL236 housing See Figure 10 NOTE There are three mounting tabs on each side and two mounting tabs on the front of the SL236 There are three mounting holes in the back of the SL236 The SL236 must be installed using the back mounting holes AND the front two mounting tabs on both sides OR by using the back mounting holes AND the front mounting tabs IMPORTANT Wood framework must be constructed of nothing larger than 2x6 wood studs across the rear of the SL236 There are no size limitations for the wood framework on the other three sides of the SL236 Mounting 3 Tabs P
14. nstructions CAUTION Changes or modifications to this unit not expressly approved by the manufacturer can void the units FCC compliance rating and make the unit illegal to operate WAR N NG Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARN NG Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the weight of all components attached to the SL236 does not exceed 35 Ibs 15 9 kg WARN NG RISK OF INJURY Do not place video equipment such as televisions or computer monitors on the ceiling panel of the SL236 The total weight of any objects on the ceiling panel must not exceed 5 Ibs 2 3 kg NOTE This system has no user serviceable parts SAVE THESE INSTRUCTIONS Installation Instructions SL236 TOOLS REQUIRED FOR INSTALLATION PARTS A 1 Ceiling Lift SL236FD Shown B 1 Push Button Assembly D 1 C 5 External Terminal Cable Tie Cover Plate S E 1 K 9 l Jumper Wire F 5 S Cable Tie un meant 6 32 x 3 16 rane SZ R
15. ord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 T 4 W S d b o OECONSUNER
16. ructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS A WAR N NG alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTI ON alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARN NG FAILURE TO READ AND FOLLOW THE FOLLOWING INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY DAMAGE TO EQUIPMENT OR VOIDING OF FACTORY WARRANTY It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided IMPORTANT Model SL236 is suitable for use
17. service position 2 Route and secure electrical and video cables using supplied mounting tabs F and cable ties C See Figure 17 IMPORTANT Leave slack between securing points OI 3 Connects to projector Figure 17 Connecting Control Wiring following all local codes and ordinances WARNING All wiring should be performed by a licensed electrician 1 Unplug the SL236 s power cord used for testing 2 Remove the jumper wire and supplied push button wiring previously installed in the Pre Test Lift before Installation section from the external terminal block See Figure 3 3 Connect control wiring following instructions included with the controller and information in Table 1 Wiring Table NOTE Any knockouts removed in the SL236 must be replaced with a supplied rubber grommet H 4 Feed the video and or communications cables through the knockout in the rear or top of the lift and connect it to the projector NOTE Ensure there is enough slack in the cables to allow for up and down movement of the lift 5 Secure cables as necessary using supplied mounting pads F and cable ties C CAUTION KEEP SL236 OPEN WHILE PROJECTOR IS RUNNING OR IN COOLING MODE Premature bulb failure or damage to electrical components may occur if lift closes NOTE If SL236 is cycled up and down repeatedly the motor s thermal overload protection will stop operation Operation will
18. ted to ground initiating any other function 13GROUUNNDD j amp rund Immediately reverses direction of travel when aoaaa eaaa kande o nomerar sone to groun ato mor mode 7 oenas ____ w pmsiwiewiikranaw monenarysonedintegunhieremrmode RETRACT ERROR triggered while unit is retracting momentary connection to ground initiates error mode E EXTEND LIMIT RELAY full extension 17 EXTEND LIMIT RELAY A A set of internal dry contacts when unit reaches RETRACT LIMIT RELAY full retraction 19 RETRACT LIMIT RELAY x E ojew jerund 0 0 E 14 Installation Instructions SL236 SUM ADJ5 pau 10 umomq ta S im Di o c s s 95 af J D Ld O o u U W ig i xo 5 E FE 8 Sc U S E o U S o ii pelg fa Q Q OO AO m Le eN T T Le m a E m E i 2 s o x U 9 E ca a 5 m d 8 v E 9 E v Z JE im 7 o Gi o a N el Figure 19 15 SL236 Installation Instructions CI CH E F USA International Our Mounts Your Vision m Europe Chief Manufacturing a products division of Milestone AV Technologies Asia Pacific 8820 002008 Rev02 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 04 10 gt TI U gt TI U gt TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Felleno
19. ubber Grommet Installing In A Suspended Ceiling SL236SP 7 Installing In A Wood Framework Joists 9 Installing Projector On SL2396 9 Adjustments 10 Routing Cables 11 Connecting Control Wiring 11 Connecting To Power Supply 12 Wiring Options 12 SL236 Installation Instructions LEGEND Tighten Fastener Phillips Screwdriver Apretar elemento de fijaci n Marcar con l piz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com l pis Serrare il fissaggio GB Segno a maiita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Adjust Aflojar elemento de fijaci n Perforar Befestigungsteil l sen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou TABLE OF CONTENTS Bie iy PR 2 Table 1 Wiring Table 13 Tools Required For Installation 3 Table 2 Internal Terminal Descriptions 14 RE PWC 3 Internal External Wiring Terminal E ATE 4 Descriptions 15 B1 sek VET 5 Installat
Download Pdf Manuals
Related Search