Draper Access/Series M AutoReturn
Contents
1. brush or cloth and carefully dust the surface DO NOT USE SOAP WATER SOLVENTS OR ABRASIVES These substances will damage a glass beaded viewing surface Case Dimensions Mounting hardware supplied by others g Mounting brackets slide left and right as needed fgagement bracket one on each end of the bottom access panel clicks into place with the ball detent on each endcap Mounting Bracket Dimensions 3 _ gt 4 lt 3 16 Yo ry R1 4 1 8 13 8 413 16 gt 73 4 gt lt q 9 p www draperinc com DRAPER 765 987 79992. Installation Operating Instructions Access Series M Projection Screen by Draper Caution Read instructions through completely before proceeding Follow instructions carefully Installation contrary to instructions invalidates warranty Entire bottom of screen case should be unobstructed to permit access to bottom panel for servicing Screen should be installed level using a carpenter s level Nothing should be fastened to screen dowel or viewing surface NOTE Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment Hanging Screen When locating viewing surface and checking clearance for screen operation remember surface is centered in the length of the case Regardless of mounting method used the following points apply Mounting brackets are shipped attached to the case Engage each bracket with top of housing as shown below and tighten set screws A bracket should be within 18 of each end of screen case Brackets can be removed and case mounted with lag screws through top of case holes drilled on site Screen should be positively and securely supported so that vibration or even abusive pulling on viewing surface will not weaken installation Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen Supporting hardware chains cables s rods etc must be essentially vertical Enti
3. ly tighten the four set screws on the idler end mounting bracket Reinstall the bottom access panel as previously described Spring Roller Fabric Removal Reverse the instructions above Spring Roller Fabric Installation for removal of the unit Operating Instructions Standard To lower picture surface pull screen down Hesifate then allow screen to retract very slowly until it locks in place To raise picture surface pull screen down and while holding allow for slow retraction into the case to reduce risk of injury from falling screen Operating Instructions AutoReturn To lower picture surface pull screen down Hesifate then allow screen to retract very slowly until it locks in place To raise picture surface pull screen down gently until it stops then release Viewing Surface Care amp Maintenance Matt White amp High Contrast Grey Clean surface with a solution of mild dishwashing liquid diluted with warm Page 2 of 2 Retaining clip Washer Nylon bushing Roller mtg brkt as clip Roller Standard Roller AutoReturn Roller Roller Hole Dia Position 134 A j z 24 B 3 C B B C A A o J o J water Sponge the surface rinse with clear water and blot dry Do not use cleaning solvents or abrasives Glass Beaded Clean with a very soft
4. r of panel adjacent to slot in bottom of the housing With bottom access panel angled up approximately at 20 it can be lifted off of the lip of the housing and then lowered out of the housing completely a Bottom flange of Access housing Bottom access panel pushup points for panel removal Caution Beware of pinch points at ends of closure Access case as seen from below Spring Roller Fabric Installation The bottom access panel must be removed first The spear end mounting bracket has rectangular openings for accepting roller spear Back out the four set screws in bracket until they are flush with top side of bracket To engage the spear end bracket flange above the two channels in the top of the screen housing rotate the bracket approximately 45 counterclockwise to allow the top surface of the motor bracket to rest flat against the top inside of the housing Rotating the bracket clockwise until it is engaged with the channels slide it along the length of the housing toward the left end of housing leaving approximately clearance between bracket and endcap Tighten the four set screws on the bracket flange using t s hex key Engage the idler end bracket nylon bushing in the same manner as the spear end bracket and slide it toward the opposite end of the screen housing Do not tighten the set screws on this bracket until the roller fabric assembly is installed Locate the roller fabric assembly and remove
5. re bottom of case must be readily accessible after installation is complete Front back and top of case must be straight not forced to warp or bow If case is painted on location removal of roller fabric assembly is recommended prior to painting If not removed slot on bottom of case should be shielded to protect viewing surface from paint splatters or overspray Typical Installation Slots along top of case permit gt eae to Alternate g be set at an Installation angle additional set of brackets required but not included Bottom Access Panel Installation Removal Bottom access panel hooks over the lower inside edge of the screen housing and then is pivoted downward until the engagement brackets on each end of the bottom panel click into place with the ball detents on each endcap Make sure bottom access panel clicks in place at each end of its length Mise 411 S Pearl St Spiceland IN 47385 USA I 765 987 7999 www draperinc com I fax 765 987 7142 Copyright 2009 Draper Inc Form AccessM_Inst09 Printed in U S A Using the hook and lip as a pivot pull the panel downward until the engagement brackets click into place with the ball detent on each endcap With bottom access panel angled up approx 20 degrees engage hook on the panel with lip of the housing Engagement bracket ia one on each end of the i bottom access panel Cy Remove bottom access panel by pushing up at each corne
6. the retaining clip and flat washer from the idler end pin and remove retaining clip from the spear Remove brackets from roller NOTE This may require two people to perform safely Raise the roller fabric assembly up into the screen housing and engage the spear of the roller completely into the spear mounting bracket If roller is 13 4 diameter there will be an arrow imprinted on the spring end of the roller This arrow must be pointing UP and you must use the slot closest to the edge of the bracket If roller is 2 4 or 3 diameter there will be a notch cut out on the spring end of the roller This notch must be pointing DOWN and you must use the appropriate slot Continued on page 2 If you encounter any difficulties installing or servicing your Access Series M screen call your dealer or Draper Inc in Spiceland Indiana 765 987 7999 or fax 765 987 7142 Access Series M by Draper Continued from Page 1 Install the retaining clip on the spear locking spear and bracket together While supporting the idler end of the roller slide the idler end mounting bracket toward the roller Insert the roller pin into the nylon bushing on the idler end mounting bracket The roller idler pin needs to go through the idler bracket far enough to allow the washer and retaining clip to be reinstalled on the pin Failure to replace the washer and retaining clip as shown could result in the separation of the roller from the brackets Secure
Download Pdf Manuals
Related Search