Gefen GTV-ETH-2-COAX
Contents
1. TX RE PLC connected nodes gg120EsC 008 159 161 The local node that the computer is connected to will appear as the ETH connected node All remote nodes will be listed as PLC connected nodes NOTE Both the local and remote nodes must use the same Net ID and encryption passwords for proper operation These will be configured in the next step However it is important to configure the remote nodes first If the local node is configured first all remote nodes will become inaccessible and will have to be removed from their locations and physically connected to the computer where they can be configured to match the local node s settings 7 To begin configuration click on the mac address of the remote node PLC connected node and then click on the next button Gelen TY configuration assist ant Gefen TV configuration assistant Goefenli 7 The assistant detected following nodes in the electric network H you think more nodes should ba shown sure here nodes are connected and prest Update List Once all nodes are in ihe let select the node bo configure and press Theri button you do nol remember the password of the node you wil have fo reset the node wih factory values pressing Factory Reset MAC Net ID Alias Quality ETH connected node AX PLC connected roch ME 348 13 CONFIGURING THE GEFENTV ETHERNET OVER Gefen TV c2. Ethernet Uver Coax GTIV ETH 2 COAX User Manual WWVV gefentv com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday PST Write To Gefen Inc c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentv com support gefentv com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice GefenTV Ethernet Over Coax is a trademark of Gefen Inc 2009 Gefen Inc All Rights Reserved All trademarks are the property of their respective companies Rev X2 A O O 17 19 24 27 28 29 CONTENTS Introduction Operation Notes Features Sender Panel Layout Sender Panel Descriptions Receiver Panel Layout Receiver Panel Descriptions GefenTV Ethernet Over Coax Software Installation Connecting The GefenTV Ethernet Over Coax Automatic Security Setup Feature Advanced Configuration Web Configuration Firmware Update Procedure Specifications Warranty INTRODUCTION Congratulations on your purchase of the GefenTV Ethernet Over Coax Your complete satisfaction is very important to us Gefen TV Gefen TV is a unique product line catering to the growing needs for innovative home theater solutions We specialize in total integration for your home theater while also focusing on goin
3. The program files will copy to the specified location previous step When the process is complete you will see the window below Click on the finish button to complete the software installation process Gefen TV Ethernet over Power Line Setup Completing the Gefen TV Ethernet over Power Line Setup Wizard Gefen TV Ethernet over Power Line has been installed on vour computer Click Finish to close this wizard 10 CONNECTING THE GEFENTV ETHERNET OVER COAX 1 Connect the source i e computer router switch to the GefenTV Ethernet Over Coax sender unit using the supplied CAT 5e cable 2 Connect the GefenTV Ethernet Over Coax sender unit to a coaxial RG 59 or RG 6 cable system Please ensure that the connected coaxial cable system has an available endpoint either directly or through a coaxial cable splitter 3 the GefenTV Ethernet Over Coax receiver unit to the coaxial cable system 4 Connect the Ethernet devices i e computer game system set top box to the GefenTV Ethernet Over Coax receiver unit Up to four devices are supported 5 Connect the included power cables to both the GefenTV Ethernet Over Coax sending and receiving units POWER LED Once the power cable is connected the Power LED should become active with a solid blue color LAN LED When a valid Ethernet connection is detected on the sending and receiving Ethernet jacks their corresponding LED s will become active and
4. and it may not be possible to put all Slave nodes in the ASCM within the time frame It is also possible to temporarily relocate the Slave nodes to a coaxial port closer to the Master node for this configuration process and then move them to their permanent location after this process is complete If a Slave node is accidentally set as a Master node you can hard reset the node by pressing and holding the Security Reset button for approximately 10 seconds This will revert the node to a Slave node and reset all internal configurations to factory settings 18 ADVANCED CONFIGURATION There are optional advanced settings that can be configured for each node The advanced menu can be accessed directly through the main configuration page Click on the MAC address of the node you wish to configure and click on the advanced button to the left of the node listing Gelen TY conliguration assist ant Gefen TV configuration assistant gt efen arriere eletti rev be sure These nodes connected and press Update List Once all nodes ane in Ihe list select the nodis bo configure and press Mest button you do nod rermiestibesr the password of the node you will have fo the node with factory valuez pressing Factory Reset ETH connected neo PLC connected nodes gga GENERAL PLC Padi advanced conligur ation qr General Pro Multicast Vien Det Det Advanced Hade ae Aaral Factoi
5. ID and Encryption Key set 4 Open the Gefen TV Config Tool page 12 There should be a random ASCII value as the Net ID If you wish to use this Net ID for the other Slave nodes proceed to step 5 Otherwise you can now set your own Net ID and encryption password which will be applied to all of the Slave nodes in the next step To do this click on the local ETH connected node MAC address and press the next button Change only the Net ID and encryption password fields and click on the next button Once the local node has been updated proceed to step 5 5 For this step to complete successfully both the Master and Slave nodes have to be in ASCM To do this press and hold the Security Reset button on the Master node for approximately 2 seconds The Power LED should begin flashing RED Within 30 seconds press and hold the Security Reset button on the Slave node s for 2 seconds to enter ASCM The Slave node s Power LED should also begin to flash while it receives the Net ID and Encryption Key information from the Master node Once the Power LED on both the Master and Slave nodes stop flashing and glow solid the setup will be complete Check this by opening the Gefen TV Config Tool and seeing that all nodes have the same Net ID NOTE If the Slave nodes are located at a great distance from the Master node itis recommended that Step 5 be repeated for each Slave node separately The window that each device remains in ASCM is only 30 seconds
6. Input Input for the supplied AC power cable Coaxial Output Coaxial output to link the sending and receiving units together This connector will support RG 6 and RG 59 cables LAN 1 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 1 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port LAN 2 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 2 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port LAN 3 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 3 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port LAN 4 LED This LED will activate when a connection from a valid Ethernet device to Ethernet port 4 is established It will blink when activity is detected to signify that data is actively being trafficked to and from this port Link LED This LED will activate once a link has been established between the sending and receiving units It will blink when activity is detected to signify that data is actively being trafficked to and from the sender Power LED This LED will activate once the included power supply is properly connected 7 GEFENTV ETHERNET SOFTWARE
7. The default password is 24 WEB CONFIGURATION MAIN PAGE Qe e menm im ime z Jr d jag ng 3 efen ty DWIOP 9010 Web Configuration An aulae Lenger fg PLC oeren PLE Pert MARC Arer i20E 6 TOR Faber ir tetris EXTA Hur ir a ra Charge ee L ssral Information MAC MAC Apes IS ADC RX AUC TX Acces Protecol Lm get Cheer contig see Tu F r Nep Bridge tair sn r H Grokied rim TY Threagkper Fit 106 liridgw dang AU pde Type EK Vall Ferit pa di 183 IHE T ER Mumbi of Denr Duablid TAG Durst The main page will display general configuration information Clicking on the further information link will navigate to a new page with all the current configuration information see page 26 Clicking on the change configuration link will navigate to a new page where all configuration options will be available for adjustment see below WEB CONFIGURATION N P gp Web Comiganation Change Contiguratiam Micrasoft mennel Explarer provided hy olen inc E hp t hire dr Bowne 10 we Configuraben Change Configurar 3 efen ty DW10P 9010 Web Configuration ALAC Configuration In Home AV Configuration Node Type Network identifier h
8. from the main page 27 SPECIFICATIONS Standard Support un aussen UPA DHS 200 Mbps PLC Interface One Power Line port One coaxial port 4 Ethernet 10 100M Ports 21610 e 3DES 168 bits encryption x AC 100 240V 50 60Hz 0 15A Power Consumption 8W 230V Max amp 7W 110V Max Operating Temp 0 40 C 32 104 F Operating Humidity 22 10 90 non condensing Storage Temp RANGE 20 70 C 4 158 F Storage Humidity een 5 95 non condensing Storage Altitude Sea level to 40 000 feet 1 le tte EE 15 B Class B CE Class B 28 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties
9. INSTALLATION How to Connect the GefenTV Ethernet Over Coax Installation of the GefenTV Configuration Assistant 1 Insert the included installation CD ROM into your computer that will be used to configure the GefenTV Ethernet Over Coax 2 The auto run will begin the installation process If auto run does not start or auto run has been disabled please navigate to X V drive where X is the drive letter or your CD ROM drive and run the autorun exe file 3 Click on the Install Utility option CD Autorun Gefen Sie ir r Power Line Anstall Utility D Quick Installation Guide S Browse User Manual Guide 4 Choose your preferred language and click on the OK button to continue Currently English is the only selectable language Installer Language Please select a language GEFENTV ETHERNET OVER COAX SOFTWARE INSTALLATION 5 Close all other applications and press the Next button to continue Gefen TV Ethernet over Coax Setup ee Welcome to the Gefen TV Ethernet over Coax Setup Wizard This wizard will guide you through the installation of Gefen TV Ethernet over Coax It is recommended that you close all other applications before starting Setup This will make it possible to update relevant system files without having to reboot your computer ATTENTION To install the software you must have administrator user privileges If you do not have such privileg
10. connected to the local node 3 Start the Gefen TV Config Tool from this location Start Menu All Programs GefenTV Ethernet Over Coax Gefen TV Config Tool 4 The introduction screen should appear as the image below Click on the next button to continue Gefen configuration assistant Welcome to the assistant for the Gefen TV configuration This assistant will help you to configure your Gefen PLC node Once the assistant is finished the Geten PLC node will be fully ready for ts use Before you start the assistant be sure that the Gefen PLC Nodes are correctly connected to the electric network Besides be sure you have the ETH wire connecting correctly the modem with the computer 5 The program will begin to search for all connected nodes CONFIGURING THE GEFENTV ETHERNET OVER 6 Once all possible nodes have been detected the program will display all of these nodes as in the window below Gefen TV configuration assist ant Gefen TV configuration assistant Goefenli 7 The assistant detected following nodes in the electric network H you think more nodes should ba seen sure hese nodes ans connected and press Update Lisl Once all nodes are in ihe legt select the node to configure and press Theri button li you do nol remember the password oi the node you vil have do reset the node with factory values pressing Factory Rese MAC Nt 10 Nios Qual ETH connected node
11. e fields are completed click on the next button to continue 14 CONFIGURING THE GEFENTV ETHERNET OVER 9 Once the update is complete a message will appear to indicate the update was successful Click on the ok button to continue Gefen Config Tool J Updated successfully 10 Once the update to the remote node is complete you will be presented with a window that will give the option to either return to the main configuration window or continue with advanced configuration Gefen TV A assistant Gefen TV Config Tool v2 7 228 PLC node configuration completed successfully PLC node is ready to use Please press Next to keep configurating nodes Press Advanced for advanced operations For basic usage it will not be necessary to continue to the advanced configuration For advanced options please see the ADVANCED CONFIGURATION section on page 19 To continue with the basic configuration click on the next button 15 CONFIGURING THE GEFENTV ETHERNET OVER 11 Once the configuration for the remote node is complete the local node will then have to be configured Click on the local node which is labeled as the ETH connected node and press next to continue Gefen TV configuration assistant Gefen TV configuration assistant Gefen 7 The assistant detected following nodes in the electric network H you think more nodes should ba shown be sure hepe nodes are connected and pre
12. eir w for OR This page will allow the user to adjust all options that are available just as in the ADVANCED CONFIGURATION PANEL in the GEFENTV CONFIG TOOL 25 WEB CONFIGURATION The configuration options are as follows MAC Configuration Network Configuration Multicast Configuration VLAN Configuration Priority Configuration QOS Security Configuration Hardware Reset Flash Upgrade Please refer to the ADVANCED CONFIGURATION section starting on page 19 for information on the above categories Going back to the main page can be done by clicking on any of the Return to main page links FURTHER INFORMATION P Nip 192 168 2 1 fee vd A 2010 Web Configuration Further Information efe n ty DW10P_9010 Web Configuration Svstem Information Uperne Firmware Version Return to main page MAC States MAC Address MAC Twe Node Network Identifier Encryption Kev ASCII Renan te mam This page will display all of the information and status of the current node The following sections are listed System Information MAC Status Network Status PHY Status Multicast Status VLAN Status Priority Status Security Status Information on this page is not configurable If you wish to make adjustments to any of these categories return to the main menu by clicking on any of the Return to main page links on the page Then click o
13. es please contact your systems administrator Click Next to continue Leo 6 Please read the license agreement and click on the Agree button to continue Gefen TV Ethernet over Power Line Setup License Agreement Please review the license terms before installing Gefen TV Ethernet over Power Line C with offices located at 1949 5th Street Suite 103 is California USA CACE or Licensor and icensee as defined hereunder If you accept the terms of the agreement click I Agree to continue You must accept the agreement ko install Gefen TV Ethernet over Power Line ee Tore Do emen _ GEFENTV ETHERNET OVER COAX SOFTWARE INSTALLATION 7 Please choose the program installation destination The default location is Program Files Gefen TV Ethernet Over Coax set your own destination click on the browse button and navigate to your preferred location Click the install button to continue Gefen TV Ethernet over Power Line Setup Choose Install Location Choose the Folder in which to install Gefen TV Ethernet over Power Line Setup will install Gefen TV Ethernet over Power Line in the following Folder To install in a different Folder click Browse and select another Folder Click Install to start the installation Destination Folder C Program Files Gefen TV Ethernet over Power n Space required 5 3MB Space available 88 8GB 4 lie fF Install y t 8
14. expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information please visit Gefen s Warranty web page at http www gefen com kvm aboutus warranty jsp PRODUCT REGISTRATION Please register your product online by visiting Gefen s web site at http www gefen com kvm Registry Registration jsp 29 Rev X2 MA ETH 2 COAXx 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefentv com support gefentv com E e c ix
15. g above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line and hope you find your solutions Don t see what you are looking for here Please call us so we can better assist you with your particular needs The Gefen Ethernet Over Coax The Gefen TV Ethernet Over Coaxial Sender and Receiver units send RJ 45 Ethernet over RG 59 or RG 6 Coax cable at a distance of up to 300m 1000 feet Ideal for legacy installations where Coaxial cable is already permanently in place these devices breathe new life into remote network extensions where re wiring is not possible How It Works Connect your existing Ethernet network cables to the Ethernet Over Coaxial Sender unit then plug in your Coaxial cable to the Coaxial jack on the Sender unit At the other end of your Coaxial cable run attach the Ethernet Over Coax Receiver unit and your network cables Power cycle your equipment You will now receive Ethernet network signals at the end of your cable run as if you had cabled the run with Ethernet cables OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE GEFENTV ETHERNET OVER COAX This device passes all 10 100BASE T Ethernet network protocols TCP IP NETBUEI Microsoft Networking etc at speeds of up to 200Mbps Full duplex fast Ethernet All devices connected to the sending and receiving nodes must be on the same subnet with unique IP addresses to co
16. mmunicate properly Multiple receiving nodes can be used on the same coaxial cable system to extend the network to multiple locations FEATURES Features e Supports up to 200 Mbps data transmission rate e Extension of up to 1000 feet 300 meters e Web configuration for easy maintenance Features include IGMP multicast VLAN and QOS packet management e _ 3DES 168 bits encryption used for secure operation e Four RJ 45 Ethernet ports Package Includes 1 GefenTV Ethernet Over Coax sender 1 GefenTV Ethernet Over Coax receiver 2 3 foot Ethernet Patch Cable 2 Power Adapter Cables SENDER PANEL LAYOUT Front Panel Standby Ri Rasat AC In Coax Out 4 5 Top Panel LA LIME MWA Gefen Ethernet over Coar 5 SENDER PANEL DESCRIPTIONS Standby Button Pressing this will put the sending unit in standby mode The unit will not transfer any information to the receiving unit in this mode To release standby mode simply press the button again Ethernet Input Port Connects to the Ethernet source i e a router computer or Internet connection via a standard network cable Security Reset Button Pressing this button for 2 seconds will activate the Automatic Security Configuration please see page 17 Pressing this button for more than 10 seconds will perform a factory reset AC Power Cable Input Input for the supplied AC power cable Coaxial Output Coaxial
17. n the Change configuration link which is also available on the main page 26 FIRMWARE UPDATE PROCEDURE The firmware for the GefenTV Ethernet Over Coax can be updated by FTP TFTP or a direct file The firmware update can be executed from either the ADVANCED CONFIGURATION PANEL or the WEB UTILITY UPDATE VIA THE ADVANCED CONFIGURATION PANEL Firmware updates can be accomplished from the General tab in the ADVANCED CONFIGURATION PANEL See page 19 for instructions on how to enter the ADVANCED CONFIGURATION PANEL ADDR T32 168 2179 ME THAS 255 255 255 0 GATE 0 IF KAUM RT gre HL TMASK 255 255 Upgrade Via FTP or TFTP 1 Select the update protocol Either FTP or TFTP 2 Enter the server IP address 3 Enter the user name and password 4 Enter the name of the file if the file is not in the root directory of the TFTP or FTP directory you have to write the whole route from root server directory 5 Select which section you would like to update Firmware Loader or Factory Settings 6 Click on the firmware update button Upgrade Via File 1 Use the browse button to the right of the firmware file window and select the firmware update file You can also manually type the full path to the firmware file 2 Click on the upgrade firmware button NOTE This procedure is the same using the web utility The web update section is located in the change configuration settings which is accessible
18. network ID and the alias for the node For a detailed description of each of these options please see page 14 21 ADVANCED CONFIGURATION IP ADDR 192 IER 2 178 nn 0000 SN STATEsDona MODE STATE 13 JAGC_Fix_STATE Ensbled This option will enable or disable the node s ability to accept VLAN data If this feature is enabled on one of the nodes it must be set on all other for VLAN tag packets to pass QOS PLC Node advanced confiquration Pe Mulicssi Security G05 QoS Advanced Quality of Service At ADDA MESSAGE Vald Piest upc IF_CONFIG_DPTIONS DHCP Fixed CONFIGsF ied IF ADDA 182 168 2179 ADDR NVAAM 1 92 168 2 173 JH SIE 255 255 255 0 GATEWAY AVRAM 0 0 000 SIN No RG STATES TX STATE Disabled 5 STATEaZ ACCESS STATE SCONE ALITOCUMF STATE QOS quality of service is supported for managing traffic between nodes The supported protocols are TCP port priority UDP port priority 802 1p TOS RFC 1122 DSCP RFC 2475 No Priority Oe Se 22 ADVANCED CONFIGURATION ADAVANCED QOS PLC hode advanced configuration INFO 3C 7008 r QoS Advanced PASS De General Network Mac Pie Secunty Van 5 K Ss S010 Quabl of Service SYTSUPTIME 0 days h Gm EURE D evt 1 sedes Vale Place upe DHCP CR QOS
19. onfiguration assistant Gefen TV configuration assistant Gefen ty This is the current configuration of the PLC node If you want to modify some parameter do it and press Next button PLC Node configuration Current firmware spi dwi p 901052 4 6 cvs Net ID Encryption key Alias Kind of node New password Confirm password Pv Ne J Ext The PLC node configuration screen is separated into the following items NET ID This is the name of the network This name must be the same for both the local and remote nodes for proper operation The NET ID can be an ASCII string up to 20 characters long ENCRYPTION KEY This is the password needed for network authentication by all nodes If you wish to set an encryption key please set the NET ID first The password can be an ASCII string up to 24 characters long ALIAS This name is for easy identification of the node This can be an ASCII string of up to 10 characters long This field is optional NEW PASSWORD CONFIGURATION PASSWORD This is to set the configuration password If a new password is set here the configuration tool will ask for it every time you access the node The default password is paterna This field is optional CONFIRM PASSWORD The password entered into the new password listing above must also be entered here This is for confirmation purposes Enter the Net ID encryption key and alias into the corresponding fields Once thes
20. output to link the sending and receiving units together This connector will support RG 6 and RG 59 cables LAN LED This LED will activate when a connection to a valid Ethernet source is established It will blink when activity is detected to signify that data is actively being trafficked to and from the receiver Link LED This LED will activate once a link has been established between the sending and receiving units It will blink when activity is detected to signify that data is actively being trafficked Power LED This LED will activate once the included power supply is properly connected RECEIVER PANEL LAYOUT Front Panel Standby 4 3 e 4 Reset 1 2 3 Back Panel In Out 4 5 Top Panel Gefen vo 6 7 8 9 10 11 Ethernet over Goan A o 10 11 RECEIVER PANEL DESCRIPTIONS Standby Button Pressing this will put the receiving unit in standby mode The unit will not transfer any information to the sending unit in this mode To release standby mode simply press the button again Ethernet Input Port 1 through 4 Connects to an Ethernet device i e a computer or gaming system via a standard network cable 4 ports are available for 4 separate devices Security Reset Button Pressing this button for 2 seconds will activate the Automatic Security Configuration please see page 17 Pressing this button for more than 10 seconds will perform a factory reset AC Power Cable
21. p the Gefen TV Ethernet Over Coaxial for secure use the Automatic Security Configuration Mode ASCM can be activated on each node Follow the below steps to automatically setup a secure connection between multiple nodes It is important to understand these concepts before proceeding with the Automatic Security Configuration Master Node Fixed Access Point The Master node is the unit that all of the Slave nodes use to copy the Net ID and Encryption Key from Because all of the nodes on a network need to have the same Net ID and encryption key to operate properly together there needs to be a single Master node that stores the information that all other Slave nodes will use to properly configure themselves A Master node is indicated by its Power LED glowing a solid RED color It is recommended to have only one Master node on the coaxial network Slave Node Normal A node in this mode will be indicated by its Power LED glowing a solid Blue color Multiple Slave nodes can be on the same coaxial network Automatic Security Configuration Mode ASCM This mode is initialized by pressing and holding the Security Reset button on the front panel for approximately 2 seconds Once the node s Power LED begins flashing RED release the button This mode lasts for approximately 30 seconds and will return to normal operation after this time period Both the Master and Slave nodes must be in ASCM for the automatic procedure to complete successfull
22. quality of service prioritization Rule 1 will be applied to all packets first and then Rule 2 Prioritization protocols are UDP is high priority TCP is low priority TCP is high priority UDP is low priority UDP port XXXX is high priority the rest is low priority UDP port XXXX is low priority the rest is high priority TCP port XXXX is high priority the rest is low priority TCP port XXXX is low priority the rest is high priority Use 802 1p prioritization No prioritization DL POLI Te 23 WEB CONFIGURATION If an IP address has been set in the ADVANCE CONFIGURATION PANEL access to the WEB UTILITY will be enabled To access the WEB UTILITY open your web browser and type the ip address into the address field The IP address is dependant on the IP Configuration Setting assigned on page 20 The IP address can either be assigned by the DHCP server or a static IP address can be manually assigned AUTHENTICATION The browser should open the authentication page displayed below er r ADWIDP SOLD Web b terrgen Gefen Gy DWi P 5010 Web Configuration Factory Ret Password Warniag will br kat Authentication To enter the WEB UTILITY enter the configuration password The default password is paterna unless modified during the setup stage on page 14 Factory Reset The unit can be reset to factory settings from this menu Enter the factory reset password
23. should emit a solid blue color LINK LED The Link LED should be flashing red on initial boot up Once a link between the sending and receiving units has been established it will emit a solid blue color on both units IMPORTANT The Link LED must be emitting a sold blue color before configuration can continue If this LED continues to flash red on both the sending and receiving units it is possible that they are not physically connected within the current coaxial cable system Please confirm that both the sending and receiving units are attached to the same coaxial cable system 11 CONFIGURING THE GEFENTV ETHERNET OVER Once both the sending and receiving units are linked and powered basic configuration can proceed This section of the manual refers to the sending unit as the LOCAL NODE and the receiving unit as the REMOTE NODE NOTE The following steps are for manual configuration of the nodes for a basic secure network These steps are optional as the nodes will function with their default settings However for security and performance purposes it is recommended that the following steps be performed Automatic configuration is also possible using the Automatic Security Configuration feature on page 17 in lieu of the procedure outlined in this section 1 Ensure that both the local and remote nodes are powered and are properly linked 2 Confirm that the computer with the installed GefenTV Ethernet Over Coax software is
24. st Update List Once all nodes ane in ihe list select the node geg bo configure and press Theri Hi pou do not remember the password of the node ou wil have do reset the node wih Tactory Values pressing Factory Alias PLC connected nodes PIT ICH 12 Using the same Net ID and encryption key from the remote node input the same information into the corresponding fields for the local node The Alias field should be set to a different name as the remote node for easy identification Gefen TY confiquration assistant Sa gt ex Gefen TV configuration assistant Gefen tv 3 This isthe current configuration of the PLC node If you want to modify some parameter do it and press Next button PLC configuration Current firmware spirit dwi p 901052 4 5 cvs Net ID Encryption key Alias Kind of node Mew password Confirm password ER Once the information has been input click on the next button to continue A confirmation window will appear once the update is complete The same window in step 10 will appear with the option to continue with the advanced configuration It is not necessary to continue with the advanced configuration for basic operation Click on the next button to return to the main configuration window and exit the configuration tool by clicking on the exit button 16 AUTOMATIC SECURITY CONFIGURATION FEATURE To quickly setu
25. ust be assigned Options are Fixed Manually assigned IP address DHCP IP assigned by the networks DHCP server Fixed IP Configuration Assign an IP address subnet mask and default gateway for web tool access Click on the Update button to apply settings made in this tab 20 ADVANCED CONFIGURATION MULTICAST PLC Hode advanced configuration ee ae General Mac Phy Mudcat 5 Van QoS QoS Advanced d B evi CE Valid Please of ux IGMP Missa IP_CONFIG_OPTIONS DHCP Fred e COHFIG IP ADDR 132 163 2178 AB STATE Disabled THG HATES ACCESS STATESDOME ALITOCOMF STATE UM 8007542 EXTA STATE STATE EXTB RI EE Eron HH 1 CONNECTION FR ADOR 20 9 PLC CONNECTION PHY TX XPUT 56 par A si IGMP Multicast This option will enable or disable the node s ability to transmit IGMP multicast data SECURITY PLC hode advanced configuration Securty Vian QoS QoS Advanced Secunty Configuration Coden give Coden Fiatsuced Encryption Ee Conima E ncnoplion ten CONHECTION PORT PLC CONNECTION ADDRTIT20E SC PLE COHNECTION PHY TX _ BRUT i The security tab will allow the user to adjust the configuration password the encryption password the
26. y TRITT Firmware Update Upgrade Protocol Server IP FTP Uzer HVELAM F ed IP ADDR NNRAMeT82 1682178 FTP HET 255 GATEWAY NVRAM Q 00 0 inim SYNC STATE Done Update Section MODE STATE 13 AGC STATE Enablad Hardware Reset This will reboot the node Settings made in this menu will be applied once the node is restarted Factory Reset This will return the node to factory default settings A password is required to complete this operation The default password 15 This has the same effect as pressing and holding the Securty Reset button on the front panel for approximately 10 seconds 19 ADVANCED CONFIGURATION Firmware Update This section is used to update the node s firmware from a server location Please see the Firmware Update section on page 27 for full details Upgrade Firmware This section is used to update the node s firmware from a file Please see the Firmware Update section on page 27 for full details NETWORK PLC hode advanced configuration T General Ph Man o5 Uo Advanced Al changes m network conhigurshon vell have effec new system reboot Configuration Fixed IP Configuration IP Adhat 132168 2173 Mach 255 255 255 0 Delak Gateway IP Address 152168 2 1 IP Configuration For access to the node s web configuration tool an IP address m
27. y When a Slave node initializes ASCM it will first attempt to find a Master node in ASCM If a Master node in ASCM is not found it will assume the role of the Master node To avoid accidentally setting a Slave node as a Master node make sure that the Master node is in ASCM when activating a Slave s ASCM Any Slave node that assumes the role of a Master node will automatically have a random ASCII Net ID and Encryption Key generated Connect the computer with the installed Gefen TV Config Tool software to the node that you wish to initially set as the Master node If a node is connected to media server or router it is recommended that this node be set as the Master node for increased performance Please refer to the next page for step by step instructions on how to activate the Automatic Security Configuration feature for the Gefen TV Ethernet Over Coax nodes 17 AUTOMATIC SECURITY CONFIGURATION 1 Connect the computer with the installed Gefen TV software to the node you wish to set as the Master node 2 Press and hold the Security Reset button on the node ASCM located on the front panel for approximately 2 seconds The Power LED should begin to flash RED then release the button 3 After approximately 30 seconds the Power LED should stop flashing and glow solid RED This indicates that it is now a Master node If this node was a Slave node normal node before this process it will now have a randomly generated ASCII Net
Download Pdf Manuals
Related Search