Baumatic PI3SS cooker hood
Contents
1. Instruction manual User Manual for your Baumatic PI3SSS Pythagora 90 cm island cooker hood x Baumatic You will be mine NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance DD 20 06 07 Contents Page Environmental note IMPORTANT SAFETY INFORMATION Specifications of your cooker hood Using your Baumatic cooker hood The control panel The timer button Grease filter maintenance alarm Cleaning your Baumatic cooker hood The grease filters Maintenance Removing and cleaning the grease filters Changing a fluorescent bulb Fitting the carbon filter Installation Electrical connection Before beginning installation Extraction mode or recirculation mode Installing your cooker hood Completing the installation Installing the appliance at minimum height Connecting to external ducting Troubleshooting Baumatic Ltd conditions of guarantee Contact details 10 10 11 11 12 12 13 14 15 15 16 17 18 22 23 24 25 26 2 16 A 22 ENVIRONMENTAL NOTE Note Before discarding an old appliance switch off and disconnect it from the power supply Cut off and render any plug useless Cut2. are unsure of any of the information contained in this booklet please contact the Baumatic Technical Department IMPORTANT Any installation work must be carried out by a qualified electrician or competent person o The hood must be installed in accordance with the installation instructions and all measurements followed o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 amp BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building Standards Scotland Consolidated Regulations issued by the Scottish Development Department o It is dangerous to alter the specifications or to modify this product in any way Do not tamper with it or attempt to modify the appliance o When installing the hood ensure that the following recommended distances are observed between the highest point on the hob top including the burners and the bottom of the cooker hood gt Electric cookers 700 mm gt Gas cookers 700 mm gt Coal oil cookers 800 mm IMPORTANT DO NOT SET YOUR COOKER HOOD LESS THAN 700 mm ABOVE YOUR COOKER o When installed between adjoining wall cabinets the cabinets must not overhang the hob The edges of the cooker hood are sharp be mindful of this as you handle yo
3. hood over to the right so the hood locks against the framework and then fully tighten the 4 M5 screws IMPORTANT YOU MUST STILL SUPPORT THE HOOD FROM UNDERNEATH UNTIL THE 4 M5 SCREWS ARE FULLY TIGHTENED 9 Remove the masking tape from the chimney sections 10 Remove the 4 M4 metric screws that you tightened slightly in step 7 and then slide the upper chimney section downwards 11 Follow the Electrical Connection instructions on pages 15 16 IMPORTANT Do not turn on the electricity supply to the appliance at this stage of the installation process 20 o Raise the upper chimney section to the framework again and retighten the 4 M4 screws At this stage they still should not be fully tightened 12 There are two decorative side pieces H that should be used to cover the grooves in the inner chimney section o Use an appropriate tool to cut the decorative side pieces to your required length The length of the side pieces will be governed by how high you need to raise the inner chimney section o Slide the decorative side pieces into the grooves on each side of the inner chimney section o Bend down the hooks at the top of the decorative side pieces so that they sit over the top of each groove 13 You should fully tighten the 4 M4 metric screws at this stage 21 a ay or Pet itr iw i be ENA i 14 Secure the lower chimney section to the hood with the screws provided IMPO
4. the LCD display o To switch the cooker hood off press the ON OFF button again The timer button o If you press the timer button whilst the cooker hood is in operation then it will countdown for 15 minutes o During the countdown the light around the timer button will flash o When the countdown has finished the cooker hood will switch off o If you press the timer button again during the countdown the light around the timer button will go out and the cooker hood will return to normal operation Grease filter maintenance reminder o After approximately 30 hours of operation the timer button will glow red This means that the grease filters need to be cleaned o You should follow the grease filter cleaning operation that is outlined on pages 11 12 of this instruction booklet o When the grease filters have been put back in position turn on the hood and then hold down the timer button until the red light goes out o Turn the hood off and then back on again to check that the alarm has been reset o IMPORTANT The grease filters should be cleaned at the time intervals suggested on page 11 You should not wait until the maintenance alarm activates before cleaning the grease filters IMPORTANT TO MAINTAIN THE CORRECT FUNCTIONING OF THE CONTROL PANEL WE RECOMMEND THAT YOU REGULARLY CLEAN THIS AREA 10 Cleaning your Baumatic cooker hood IMPORTANT BEFORE CLEANING ALWAYS ENSURE THAT YOU HAVE SWITCHED Y
5. the cable off directly behind the appliance to prevent misuse This should be undertaken by a competent person CONFORMITY TO W E E E DIRECTIVE This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol cic on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product o The packaging materials that Baumatic uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you
6. OUR COOKER HOOD OFF AT THE OMNI POLAR SWITCH SET AT THE WALL FROM THE CABLE Cleaning O O Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth Never use abrasive powder corrosive solvents or brushes Never insert pointed objects into the motor s protective grid Only clean the control panel and grease filters with mild liquid detergents and a new damp cloth If you are using the appliance in recirculation mode then be sure to replace the carbon filters at the recommended interval see section on Fitting the carbon filter A build up of grease could cause a fire hazard Never attempt to clean the area above the grease filters The grease filters O O O O Your cooker hood includes grease filters which help to absorb grease particles to protect your kitchen amp furniture from greasy residues This metallic filters may become flammable if they become saturated with this greasy residue To prevent this fire hazard the filters should be cleaned regularly Depending on use this should be done every 10 15 days or at least once a month using hot water and normal washing up detergent DO NOT WASH THE GREASE FILTERS IN A DISHWASHER 11 Maintenance Removing and cleaning the grease filters o Remove the grease filters by lifting up the catch and then pull the filters away from the hood o Soak the grease filters in hot water and washing up liquid
7. RTANT Make sure that these screws are fully tightened Completing the installation The electrical connection should have already been completed at step 11 as per the electrical connection information on pages 15 16 At this stage you can now switch on your mains supply Fit the grease filters and charcoal filter if you are using the appliance in recirculation mode Then press the ON OFF button and check that the appliance is operating correctly on each speed 22 Installing the appliance at minimum height 1 If you are installing the product at minimum height then you need to remove the 10 screws from the framework including the 2 pre tightened screws Separate the inner and outer sections of the framework 2 Remove the 4 rivets that hold the upper plates onto the inner framework 3 Fix the upper plates to the outer section of the framework to make it stable using 4 of the screws that you have removed in step 1 IMPORTANT You should not use either of the pre tightened screws to fix the upper plates to the outer section of the framework 4 Continue the installation process from step 3 on page 19 23 Connecting to external ducting o You may find an anti draft flap included with the fixtures and fittings for the cooker hood If you are going to duct the product externally you should fit this as shown in the circular hole on top of the motor o Connect the coupling D to the top of th
8. TANT The two pre tightened screws indicated in the diagram opposite should not be loosened 18 3 Lift the framework to the ceiling and mark the position of the 4 screw holes that are indicated by the arrows in figure 3 4 Remove the framework from the ceiling Using a drill bit with an 8 mm diametre drill out the holes on the ceiling that you have just marked and insert rawlplugs into them 5 Fasten the framework to the ceiling using the screws provided 6 Adjust the inner and outer chimney sections to your required height Use masking tape to secure the chimney sections during the installation process o IMPORTANT If you are installing the appliance at minimum height then you only need to utilise the outer piece of the two chimney sections 19 7 Lift the chimney section up to the framework and then fasten it to the framework using the 4 x M4 metric screws supplied The chimney section should be fixed to the existing holes in the framework IMPORTANT Do not tighten these screws completely at this stage IMPORTANT If you are going to connect the cooker hood to external ducting then you must follow the Connecting to external ducting section on page 24 before proceeding with the steps below A ee pee bka Bai IEE IUT iUa il 8 Raise the hood to the framework and locate the 4 M5 screws on the bottom of the framework into the 4 holes that are around the outside of the motor housing Slide the
9. atulations on purchasing a Baumatic Cooker Hood PRODUCT DIMENSIONS PBS Height mm 640 1212 Width mm 898 Depth mm 656 Chimney dimensions mm 318 width x 256 depth Your cooker hood is fitted with o High extraction tangential motor o Touch control operation o 4 Speeds o 3 Stainless steel grease filters o 2 fluorescent lights Extraction capacity 800 m3 hr Optional Extra 1 x SCS14 carbon filter for air recirculation mode Using your Baumatic cooker hood The control panel o Make sure that it has been installed by a suitably qualified person as per the information contained in Baumatic s installation instructions o Find the control panel which is located at the front of the cooker hood o There are several buttons on the control panel which perform separate functions amp 1A Ee ee ee ee ee ee iJ Timer button Increase speed On off button Decrease speed Light ON OFF button 4 LCD display IMPORTANT IDEALLY YOU SHOULD TURN ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK OR AT THE VERY LEAST WHEN YOU BEGIN COOKING YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING Controlling your cooker hood o Use the ON OFF button to switch the cooker hood on o Use the plus and minus buttons to regulate the speed that the motor is running at o The speed level that you have selected will appear on
10. e appliance is connected by a qualified electrician who is a member of the N I C E I C and who will comply with the I E E and local regulations The wires in the mains lead are coloured in accordance with the following UK code Blue Neutral Brown Live Green Yellow Ground If you only find two wires in the main s lead blue and brown then neither must be connected to the earth terminal o As the colour of the wires in the appliance s mains lead may not correspond with the coloured markings identifying the terminals in your spur box please proceed as follows o The blue wire must be connected to the terminal marked N neutral or coloured black o The brown wire must be connected to the SE A 3 AMP FUSE terminal marked L live or coloured red Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area In addition check whether there is an electrical socket available that will be accessible once the hood is mounted If the product is going to be used in extraction mode then there should also be space to connect a ducting hose to the outside o Carry out all necessary masonry work prior to the fitting of the cooker hood o Ensure that all electrical connections are carried out by a suitably qualified person o Before commencing installation of the cooker hood the grease filters should be removed o Check inside the product and ensure tha
11. e being observed Note that it removes odours from the room not steam o Warning Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood including cleaning and replacing light bulbs o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose o Do not install the appliance above a cooker with a high level grill o Never leave frying pans unattended during use as overheated fats and oils might catch fire o Never flamb cook under this cooker hood o The cooker hood should not be exposed to a direct heat source from the cooking device underneath it i e a naked flame from a gas burner or heat from electric hob zones without a pan on them o Check the appliance for any signs of transport damage If you notice any damage then you should not connect your appliance to your mains supply and should contact your retailer o Never attempt to use it without the grease filters fitted or if the filters are excessively greasy o The lights on this appliance should only be used during operation of the cooker hood They should not be left on permanently and used as a lighting source THE MANUFACTURER DECLINES ALL RESPONSIBILITY IN THE EVENT OF FAILURE TO OBSERVE THE INSTRUCTIONS GIVEN HERE FOR INSTALLATION MAINTENANCE AND SUITABLE USE OF THE HOOD Specifications of your cooker hood Congr
12. e cooker hood o Connect a 125 mm ducting hose to a discharge outlet that is Suitable for cooking vapours It should have a cross section of at least 150 cm please note that the ducting hose is not supplied with the appliance but is available from the Baumatic Spares Department o The maximum distance between the coupling and your discharge outlet can be upto 3 metres long with one 90 degree bend o Before fixing the cooker hood to the framework you should connect the other end of the ducting hose to the coupling in the top of the cooker hood 24 Troubleshooting IMPORTANT If your cooker hood appears not to be operating properly before contacting the Baumatic Service Department please refer to the checklist below My cooker hood will not start o Check that the hood is connected to the power supply and whether you have selected any of the fan speeds My cooker hood is not working effectively o Check that fan speed is set to an appropriate setting o Check that the grease filters are not dirty and if they require cleaning o Ifthe hood is set up for recirculation mode check that the carbon filter does not need to be replaced o Ifthe hood is set up for extraction mode check that the ducting hose and discharge outlet are not blocked 2 D My cooker hood is noisy and or vibrating o Check whether the installation has been completed as per the instruction booklet o Itis normal to get a certain amoun
13. e filters 1 Locate the SCS14 carbon filter into the Slots on the cooker hood below the motor 2 Push the other side of the filter upwards until it clicks into place 3 Securely tighten the screw through the hole in the SCS14 carbon filter and the corresponding hole in the underneath of the cooker hood o Refit the grease filters o The carbon filter should be replaced every three months or if it shows signs of damage 14 Installation IMPORTANT Before installation and usage read all the instructions and make sure that the voltage V and the frequency Hz indicated on the rating plate are exactly the same as the voltage and frequency of your home The rating plate can be found behind the grease filters on the motor The manufacturer declines all responsibility in the event of the installer failing to observe all the accident prevention regulations in force which are necessary for the normal use and the regular operation of the electric system Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION o The cooker hood s power cable must be fitted upstream from the electrical connection using an omni polar switch with a contact distance of at least 3 mm WARNING THIS APPLIANCE MUST BE EARTHED It Should only be connected by a competent person using fixed wiring via a double pole switched fused spur outlet UK ONLY 15 We recommend that th
14. ecessary to remove the appliance from it operating position Whilst all reasonable care will be taken Baumatic Ltd cannot accept responsibility for damage sustained to any property whatsoever in this process This guarantee is in addition to and does not diminish your statutory or legal rights Contacting Baumatic Ltd Sales Service Spares Technical Advice TEL 0118 933 6900 TEL 0118 933 6911 TEL 0118 933 6922 0118 933 6933 FAX 0118 9310035 FAX 0118 986 9124 FAX 0118 933 6942 0118 933 6942 For ROI Republic of Ireland please contact one of the numbers below TEL 01 6266798 FAX 01 6266634 Thanks you for buying Baumatic Applies to UK Scotland Wales amp Northern Ireland only Republic of Ireland has 1 year labour amp 1 year parts warranty only 26 lt l Baumatic You will be mine Headquarters Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 44 118 933 6900 Sales Fax 44 118 931 0035 Service Telephone 44 118 933 6911 Service Fax 44 118 986 9124 Spares Telephone 44 118 933 6922 Technical Advice Telephone 44 118 933 6933 E mail sales baumatic co uk technical baumatic co uk Website http www baumatic com 27 Baumatic WWW baumatic com
15. for about an hour o Rinse them off thoroughly with hot water o Repeat the process if required 7 H o Refit the grease filters once they have dried o IMPORTANT Let the grease filters dry thoroughly before refitting them in the cooker hood 12 Changing a fluorescent bulb IMPORTANT BEFORE ATTEMPTING TO CHANGE A FLUORESCENT TUBE YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY o Prior to touching a fluorescent tube ensure that it has cooled down o Unscrew the fixing screws and remove the panel that covers the fluorescent tube that needs replacing o Remove the fluorescent tube by rotating it through 90 o Replace the fluorescent tube with one of the same rating as the tube originally supplied with the cooker hood o Replace the bottom panel and fully tighten the fixing screws o IMPORTANT A defective fluorescent tube should be replaced immediately o If the light still does not work make sure that the fluorescent tube is fitted properly into its housing before you call for technical assistance 13 Fitting the carbon filter If the appliance is going to be used in recirculation mode then it is necessary to fit a carbon filter This will help to absorb unpleasant odours caused by cooking IMPORTANT BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTER YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY o Remove the greas
16. on mode stale air is taken via the grease filters and passed through a charcoal filter for purification The air then re enters the kitchen via an opening in the hood For optimum performance we recommend that the cooker hood is used in extraction mode and connected to external ducting Unfortunately if you live in a flat or the hood is too far from an outside wall this may not be possible The only alternative is to recirculate the alr Do I need a charcoal filter All cooker hoods have grease filters but if you are using your cooker hood in recirculation mode then a charcoal filter must be fitted in addition to the grease filter 17 Installing your cooker hood o We recommend that at least two people install this hood IMPORTANT THE MAINS SUPPLY THAT YOUR COOKER HOOD IS CONNECTED TO MUST NOT BE SWITCHED ON UNTIL AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED 1 Identify the framework The side that has the two fully visible circles in it will be where the control panel is positioned when installation is complete IMPORTANT If you are going to install the appliance with the chimney sections at their minimum height then please turn to the Installing the appliance at minimum height section on page 23 before completing any of the steps below 2 Remove the 8 screws from the framework and then adjust it to your desired height Fully retighten the 8 screws that you have just removed IMPOR
17. t of noise and vibration due to the extraction capacity of the cooker hood DO NOT MAKE ANY ATTEMPT TO REPAIR THE APPLIANCE YOURSELF IF THE APPLIANCE IS STILL NOT OPERATING CORRECTLY PLEASE CONTACT THE BAUMATIC SERVICE DEPARTMENT ON TELEPHONE NUMBER 0118 933 6911 25 Baumatic Ltd Conditions of guarantee Dear Customer Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost giving an initial guarantee period of 24 months The extended guarantee period applies to England Scotland Wales and Northern Ireland only To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase to be covered under this guarantee This can be done online via www baumatic co uk or through returning the guarantee card which can be found in each new Baumatic appliance In addition your appliance is covered by a 5 year parts warranty Baumatic Ltd will provide free of charge the parts required to repair the appliance only if they are fitted by a Baumatic engineer for any defect that arises due to faulty materials or workmanship within a period of 5 years from the original purchase date An additional to 3 year insurance scheme for labour is available should you wish to extend
18. t there is no transit packaging or any other materials such as packets of screws guarantees etc These should be removed and kept for future use o If possible disconnect and move freestanding or slot in cookers from their position to provide easier access to the ceiling If this is not possible then a thick protective covering should be placed over the worktop hob top or cooker This will help to protect these surfaces from damage and debris 16 o Select a flat surface for assembling the cooker hood Cover that surface with a protective covering and place all cooker hood parts and fittings on it o Rawlplugs are provided to secure the hood to most types of ceilings However a qualified technician must verify the Suitability of the materials in accordance with the type of ceiling The ceiling must be strong enough to take the weight of the hood o Do not tile grout or silicone this appliance to the ceiling This appliance is designed to be surface mounted only o Remove any protective wrapping that has been put on the cooker hood or chimney sections to protect them during transit Extraction mode or recirculation mode IMPORTANT YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE What is the difference between extraction and recirculation modes In extraction mode the stale air will be taken out of the room via external ducting In recirculati
19. the watranty period Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance the policy is negated and Baumatic Ltd will be under no further liability The guarantee covers the appliance for normal domestic use only unless otherwise stated Any claims made under the terms of the guarantee must be supported by the original invoice bill of sale issued at the time of purchase This guarantee is transferable only with the written consent of Baumatic Ltd If the appliance fails and is considered either not repairable or uneconomical to repair between 12 months 2 years if registered and five years a free of charge replacement will not be offered The guarantee for any replacement will only be for the remainder of the guarantee on the original product purchased The guarantee does not cover Sinks and taps Failure to comply with the manufacturers instructions for use The replacement of cosmetic components of accessories Accidental damage or wilful abuse Subsequent loss or damage owing to the failure of the appliance or electrical supply Incorrect installation Losses caused by Acts of God civil war failure to obtain spare parts strikes or lockouts Filters fuses light bulbs external hoses damage to bodywork paintwork plastic items covers baskets trays shelves burner bases burner caps decals corrosion rubber seals In the course of the work carried out it may be n
20. ur appliance especially during installation and cleaning DO NOT CLEAN IN BEHIND THE GREASE FILTER If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air in the room When the hood is being used in extraction mode ensure that the ducting is fire retardant and that there are no bends sharper than 90 degrees as this will reduce the efficiency of the hood Ensure that the ducting used in extraction mode has the same diameter as the outlet hole all the way through Keep young children from using playing with or tampering with the cooker hood Older children and infirm persons should be supervised if they are using the cooker hood Your cooker hood is for domestic use only Please dispose of the packing material carefully children are especially vulnerable to it Dirty oil is an even greater fire risk Always put lids on pots and pans when cooking on a gas cooker Eo The manufacturer refuses to accept any responsibility for damages arising to the cooker hood or your property from a failure to observe the fire safety advice contained in this instruction booklet o Remember that when in extraction mode your cooker hood is removing air from the room it is installed in Ensure that proper ventilation measures ar
Download Pdf Manuals
Related Search