Home

Supermicro AS-1022G-NTF

1. i VGA com1 se amp 25 2 SI SH 8 S z KS P 2 m JPL1 E z e Aa cpu ail allalsaiaugllals gl ol olg glgllgle Si ZSZ Z S SE i s 2 2 A w w N N D gt D gt o gt D gt 8 A H o X a SIS Winbond BMC z re M Ae 2 SS ef M F3 mm x E WY a 8 ss siisizllszlziz 22 olol yl elel elele SS s zsszsisziszsz CPU1 oo s sisils sss s HM N N w w A E EDP2 o o D KA amp JBTI G g AMD 4 s AMD SR5670 3 SP5100 S S E i i 2 H WEI om S SATAO SATA2 SATA4 3 Joi a 3 E a 3 Uu 9 sata aras satas Z JF t FAN3 s 8 AE Notes Jumpers not indicated are for test purposes only When LE1 LED is on the onboard power connection is on Make sure to unplug the power cables before removing or installing components IPMI Intelligent Platform Management Interface 2 0 is supported by the H83DGU F For more information on IPMI configuration refer to the Embedded BMC IPMI User Guide http www supermicro com support manuals Warning To provide adequate power to the add on cards installed on the serverboard please connect the UIOP PWR connector to the power supply for these cards to work properly 5 11 SUPERSERVER 1022G NTF User s Ma
2. Hard Drive Bays System Reset Main Power Power Supply Modules USB Ports PCI Expansion Slots w Riser Cards ew LL nO EE Jo Se zc LP EIER UE Stem aera med AG Golf j Ze Sien S neoc k R f PE ANA ETE Mouse Keyboard Ports COM1 Port VGA Port Ethernet Ports 6 2 Control Panel The control panel located on the front of the chassis must be connected to the JF 1 connector on the serverboard to provide you with system status indications These wires have been bundled together as a ribbon cable to simplify the connection Connect the cable from JF1 on the serverboard to the appropriate header on the Control Panel PCB printed circuit board Make sure the red wire plugs into pin 1 on both connectors Pull all excess cabling out of the airflow path The control panel LEDs inform you of system status See Chapter 3 System Interface for details on the LEDs and the control panel buttons Details on JF1 can be found in Chapter 5 Advanced Serverboard Setup 6
3. Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them n single rack installation stabilizers should be attached to the rack In mul tiple rack installations the racks should be coupled together e Always make sure the rack is stable before extending a component from the rack You should extend only one component at a time extending two or more simultaneously may cause the rack to become unstable Server Precautions e Review the electrical and general safety precautions in Chapter 4 e Determine the placement of each component in the rack before you install the rails e Install the heaviest server components on the bottom of the rack first and then work up Use aregulating uninterruptible power supply UPS to protect the server from power surges voltage spikes and to keep your system operating in case of a power failure 2 2 Chapter 2 Server Installation Allow the hot plug SATA drives and power supply modules to cool before touching them Always keep the rack s front door and all panels and components on the serv ers closed when not servicing to maintain proper cooling Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi unit rack assembly the ambient operating temperature of the rack environment may be greater than the ambient temperature of the room Therefore consi
4. Preface Notes SUPERSERVER 1022G NTF User s Manual Table of Contents Chapter 1 Introduction i NES 0 cm o E cde 1 1 1 2 Serverboard Features PRETEREA 1 2 xii oco cr a a E eee 1 2 MEMON EE 1 2 UO c t 1 2 caca 1 2 Onboard Gontrollers POMS aucun iioc orbi ket Spp t cma Exi PER SS pe evaded 1 2 Graphics Controller PNE RR ER RT m 1 3 Other Feat feS P 1 3 1 3 Server Chassis Features e M 1 3 NEE 1 3 SATA DUDS o c O 1 3 uam cip ge c EH 1 3 Front Control eegene 1 4 Bet E 1 4 Cooling SY ci easier ee eo 1 4 1 4 Contacting SUOMI E 1 6 Chapter 2 Server Installation 2 1 Ug enee eegene 2 1 22 Unpacking the System eet 2 1 2 3 Preparing pl 2 ao Uo eee ermee eer meen netrtey Neer ny Pere re eer eevee en err eres ten ee ae 2 1 Ener 2 2 Choosing a Setup LOCA E 2 2 ee 2 2 Seref Preca tlon eT 2 2 Rack Mounting ee ET 2 3 Ambient Operating Temperature xc gesbeagegegsgeeegugd eegene beiegeg 2 3 Reduced te E 2 3 Mechanical Eoadiligius retient o ege eg 2 3 Circuit Overloading EE 2 3 ele RE 2 3 2 4 installing the System Egeter eege ege eg 2 4 Identifying the Sections of the Rack Rails ee 2 4 Jp 2 Male fiat Inner gt M T
5. e Touch a grounded metal object before removing any board from its antistatic bag Handle a board by its edges only do not touch its components peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the serverboard add on cards and peripherals back into their antistatic bags when not in use Unpacking The serverboard is shipped in antistatic packaging to avoid static damage When unpacking the board make sure the person handling it is static protected 5 1 SUPERSERVER 1022G NTF User s Manual 5 5 Processor and Heatsink Installation When handling the processor avoid placing direct pressure on the label N area of the fan Also do not place the serverboard on a conductive surface which can damage the BIOS battery and prevent the system from booting up Notes e Always connect the power cord last and always remove it before adding re moving or changing any hardware components Make sure that you install the processor into the CPU socket before you install the CPU heatsink e f you buy a CPU separately make sure that you use an Intel certified multi directional heatsink only Make sure to install the serverboard into the chassis before you install the CPU heatsinks e When receiving a serverboard without a processor pre installed make sure that the plastic CPU socket cap is in place and none of the socket pins are bent otherwise contact your r
6. eee Sener 2 4 Installing the Outer EN 2 5 vi Table of Contents Installing the Server Into the Rack esu egasEeegehegber ege Ee 2 6 Installing the Server into a Telco Hack eite iro ene be Renan echas 2 7 2 5 Checking the Serverboard KT EE 2 8 2 0 Checking the Drive Bay Setup etna retra rni ba rtu Raps sni gH 2 9 Chapter 3 System Interface Sec EEN oc 3 1 3 2 Control Panel Buttons ous eee eee nr eee ne mere ere vere nena reve err 3 1 le 3 1 PROS OU eebe dE IL Id PLE 3 1 e EE 3 2 3 3 mmol Pen LEDS visa Deiere eege 3 2 Universal Information LED audere tener ar erepti oar pn a emer mere er ener 3 2 Oe 3 3 NIC EE 3 3 PUD RE 3 3 le EE 3 3 3 4 Hard Drive Carrier LED Sissies iein ir naasa aa raine iewe caaan ia ainat Ens 3 4 Chapter 4 System Safety 4 1 Electrical Safety Precautions eege ee 4 1 EE 4 2 43 ESD Proca tonS nee ee eee eee 4 3 4 4 Operating e 4 4 Chapter 5 Advanced Serverboard Setup 5 1 Handling the Serverboard HE 5 1 Le 5 1 NP PACKING TEE 5 1 5 5 Processor and Heatsink Installaton eee ec eeceeeeeeeeeeeeneneeeeeeeeeeenteaeeeeeeeens 5 2 When handling the processor avoid placing direct pressure on the label area of the fan Also do not place the serverboard on a conductive surface which can damage the BIOS battery and prevent the system from booting up 5 2 Installing a Passive CPU En 5 4 5 3 Connecting ee E 5 5 Connecting Data ee 5 5 Elle We 5 5 Connecting the Cont
7. P1 3A P1 8B P1 4A P1 4B Memory Population for Optimal Performance For a Motherboard with Two CPUs CPU1 amp CPU2 Installed DIMMS Branch 0 Branch 1 Branch 2 Branch 3 4 DIMMs cpus resa ren sows omn P eam aal feral CPU2 P2 1A P2 2A P2 3A P2 4A 16 DIMMs CPU1 P1 1A P1 1B P1 2A P1 2B P1 3A P1 3B P1 4A P1 4B CPU2 P2 1A P2 1B P2 2A P2 2B P2 3A P2 3B P2 4A P2 4B DIMM Module Population Configuration For memory to work properly follow the tables below for memory installation DIMM Population Table DIMM DIMMs DIMM Type Reg Speeds in MHz Ranks per DIMM Slots per Populated Registered any combina Channel per Chan tion SR Single nel Rank DR Dual Rank QRzQuad Rank 1066 1333 SR or DR 1066 Mixing SR DR QR 1066 1333 SR or DR Unb DDR3 ECC 1066 1333 Mixing SR DR ine n Note 1 Due to OS limitations some operating systems may not show more than 4 GB of memory Note 2 Due to memory allocation to system devices the amount of memory that remains available for operational use will be reduced when 4 GB of RAM is used The reduction in memory availability is disproportional 5 8 Chapter 5 Advanced Serverboard Setup Possible System Memory Allocation amp Availability System Device Physical Memory Available 4 GB Total System Memory Firmware Hub flash memory System BIOS 3 99 GB Local APIC 3 99 GB Area Reserved
8. The Power On LED connector is located Pin prse on pins 15 and 16 of JF1 This connection F Pin Definition is used to provide LED indication of power SSES y being supplied to the system See the table HS sue 16 Control on the right for pin definitions NMI Button NMI Button The non maskable interrupt button header is Pn m s located on pins 19 and 20 of JF1 Refer to the ae rd Pin Definition table on the right for pin definitions 19 Control 20 Ground Chapter 5 Advanced Serverboard Setup Universal Serial Bus Ports Two Universal Serial Bus ports USB 2 0 are located beside the Keyboard and Mouse PS2 ports One additional Type A port USB6 is included on the motherboard See the table on the right for pin definitions USB Headers Four USB 2 0 headers USB2 3 and USB4 5 are also included on the motherboard These may be connected to provide front side ac cess A USB cable not included is needed for the connection See the table on the right for pin definitions Fan Headers This motherboard has eight fan headers Fani to Fan8 These 4 pin fans headers are backward compatible with 3 pin fans However fan speed control is available for 4 pin fans only The fan speeds are con trolled by the BIOS See the table on the right for pin definitions Serial Ports The COM serial port is located beside the VGA port Refer to the motherboard layout for the location of
9. The left frame displays all the options that can be configured Grayed out options cannot be configured The right frame displays the key legend Above the key legend is an area reserved for a text message When an option is selected in the left frame it is highlighted in white Often a text message will accompany it Note that BIOS has default text messages built in We retain the option to include omit or change any of these text messages Settings printed in Bold are the default values A b indicates a submenu Highlighting such an item and pressing the Enter key will open the list of settings within that submenu The BIOS setup utility uses a key based navigation system called hot keys Most of these hot keys lt F1 gt lt F10 gt lt Enter gt lt ESC gt lt Arrow gt keys etc can be used at any time during the setup navigation process 7 2 Main Menu When you first enter AMI BIOS Setup Utility you will see the Main Menu screen You can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys The Main Menu screen provides you with a system overview which includes the version built date and ID of the AMIBIOS the type speed and number of the processors in the system and the amount of memory installed in the system SUPERSERVER 1022G NTF User s Manual System Time System Date You can edit this field to change the system time and date Highlight System Time o
10. located at LE1 works in conjunction with the rear UID switch to provide easy identification for a unit that might be in need of service Refer to Page 2 15 for further UID details ae DP2 is an Onboard Power LED When this State System Status LED is lit it means power is present on the On Standby power present on serverboard Be sure to turn off the system motherboarg and unplug the power cord s before remov ing or installing components 5 21 SUPERSERVER 1022G NTF User s Manual 5 11 SATA Drive Connections SATA Ports SATA Ports Pin Definitions SATAO SATA3 Pin Definition Pin Definition There are no jumpers to configure the SATA ports which are designated SATAO through SATA5 See the table on the right for pin d definitions 4 Ground 5 22 Chapter 5 Advanced Serverboard Setup 5 12 Enabling SATA RAID Now that the hardware is set up you must install the operating system and the SATA RAID drivers if you wish to use RAID with your SATA drives The installation procedure differs depending on whether you wish to have the operating system installed on a RAID array or on a separate non RAID drive See the instructions below for details Serial ATA SATA Serial ATA SATA is a physical storage interface that employs a single cable with a minimum of four wires to create a point to point connection between devices This connection is a serial link that supports a SATA transf
11. p n FAN 0086L4 4 Push the new fan into the vacant space in the housing while making sure the arrows on the top of the fan indicating air direction point in the same direction as the arrows on the other fans 6 3 SUPERSERVER 1022G NTF User s Manual 5 Reposition the fan housing back over the two mounting posts in the chassis then reconnect the fan wires to the same chassis fan headers you removed them from 6 Power up the system and check that the fan is working properly and that the LED on the control panel has turned off Finish by replacing the chassis cover 6 4 Drive Bay Installation Removal Removing the Front Bezel If your system has a front bezel optional attached to the chassis you must first remove it to gain access to the drive bays To remove the bezel first unlock the front of the chassis then press the release knob see Figure 6 3 Carefully remove the bezel with both hands A filter located within the bezel can be removed for replacement cleaning It is recommended that you keep a maintenance log of filter cleaning replacement since its condition will affect the airflow throughout the whole system Figure 6 3 Removing the Front Bezel 1 Unlock 2 Press release knob 3 Remove bezel assembly Accessing the Drive Bays Hard Drives
12. 12C 1 asta connection on your system around 3 Clock 4 No Connection Video Connector A Video VGA connector is located below the COM Port on the IO backplane This connector is used to provide video and CRT display Compact Flash Card PWR Connector A Compact Flash Card Power Connector is located at JWF1 For the Compact Flash Card to work properly you will need to en able with JCF1 and connect a Compact Flash Card power cable to JWF1 first 5 18 Chapter 5 Advanced Serverboard Setup 5 9 Jumper Settings SX o elele Explanation of Jumpers M To modify the operation of the motherboard jumpers can be used to choose between optional settings Jumpers create shorts be tween two pins to change the function of the connector Pin 1 is identified with a square Mid gt solder pad on the printed circuit board See the diagram at right for an example of jump ing pins 1 and 2 Refer to the motherboard layout page for jumper locations Jumper 3 2 1 L Note On two pin jumpers Closed means the jumper is on and Open means the jumper is off the pins ve JBT1 contact pads CMOS Clear JBT1 is used to clear CMOS which will also clear any passwords Instead of pins this jumper consists of contact pads to prevent accidentally clearing the contents of CMOS To Clear CMOS 1 First power down the system and unplug the power cord s 2 With the power disconnected shor
13. 1333 1066 800 MHz unbuffered ECC non ECC SDRAM in 16 DIMM slots See the following table for memory installation Memory speed support is dependent on the type of CPU used on the board Installing Memory Modules 1 Insert the desired number of DIMMs into the memory slots starting with DIMM 1A For best memory performance please install memory modules of the same type and same speed on the memory slots as indicated on the tables below 2 Insert each DIMM module vertically into its slot Pay attention to the notch along the bottom of the module to avoid installing incorrectly see Figure 5 3 3 Gently press down on the DIMM module until it snaps into place in the slot Repeat for all modules To Install Insert module vertically and press down until it snaps into place Pay attention to the align ment notch at the bottom To Remove Use your thumbs to gen tly push the release tabs near both ends of the module This should release it from the slot Figure 5 3 Installing DIMM into Slot III ymmo Note Notch should align with the receptive key point on the slot Release Tab Release Tab Top View of DDR3 Slot 5 7 SUPERSERVER 1022G NTF User s Manual Memory Population for Optimal Performance For a Motherboard with One CPU CPU1 Installed reps cpu Brancho Branch Branch Saz some cms mea Les 4 DIMMs CPU1 P1 1A P1 2A P1 3A P1 4A 8 DIMMs CPU1 P1 1A P1 1B P1 2A P1 2B
14. 3 System Fans Four 4 cm heavy duty counter rotating fans provide the cooling for the SuperServer 1022G NTF Each fan unit is actually made up of two fans joined back to back which rotate in opposite directions This counter rotating action generates exceptional airflow and works to dampen vibration levels It is very important that the chassis top cover is properly installed and making a good seal in order for the cooling air to circulate properly through the chassis and cool the components See Figure 6 2 for details 6 2 Chapter 6 Advanced Chassis Setup Figure 6 2 System Cooling Fans System Fan Failure Fan speed is controlled by system temperature via a BIOS setting If a fan fails the remaining fan will ramp up to full speed and the overheat fan fail LED on the control panel will turn on Replace any failed fan at your earliest convenience with the same type and model the system can continue to run with a failed fan Remove the top chassis cover while the system is still running to determine which of the two fans has failed Then power down the system before replacing a fan Removing the power cords is also recommended as a safety precaution Replacing System Fans 1 After determining which fan has failed turn off the power to the system 2 Unplug the fan cable from the serverboard and remove the failed fan from the chassis 3 Replace the failed fan with an identical 4 cm 12 volt fan available from Supermicro
15. AMD Power Now feature 7 3 SUPERSERVER 1022G NTF User s Manual Power Cap This option can decide the highest P state in the OS Options include P state 0 through P state 4 ACPI SRAT Table This option Enables or Disables the building of the ACPI SRAT Table CPU Down Core This option sets down core support for the CPU Options include Disabled 2 Cores through 10 Cores in even numbered increments C1E Support This option enables C1E support Options include Enabled and Disabled Clock Speed Spectrum This option enables or disables spread spectrum modulation gt Advanced Chipset Control gt NorthBridge Configuration gt Memory Configuration Bank Interleaving Select Auto to automatically enable a bank interleaving memory scheme when this function is supported by the processor The options are Auto and Disabled Node Interleaving This option enables node memory interleaving Options include Auto or Disabled Channel Interleaving This option enables channel memory interleaving Options include Auto or Disabled CS Sparing This setting will reserve a spare memory rank in each node when enabled Options are Enabled and Disabled Chapter 7 BIOS Bank Swizzle Mode This setting Enables or Disables the bank swizzle mode gt ECC Configuration ECC Mode This submenu affects the DRAM scrub rate based on its setting Options include Disabled Basic Good Super Max and User Selecting User
16. Change User Password Select this option and press Enter to access the sub menu and then type in the password Boot Sector Virus Protection This option is near the bottom of the Security Setup screen Select Disabled to deactivate the Boot Sector Virus Protection Select Enabled to enable boot sector protection When Enabled AMI BIOS displays a warning when any program or virus issues a Disk Format command or attempts to write to the boot sector of the hard disk drive The options are Enabled and Disabled 7 13 SUPERSERVER 1022G NTF User s Manual 7 5 Boot Menu gt Boot Device Priority This feature allows you to prioritize the boot sequence from the list of available devices A device that is in parenthesis has been disabled in the corresponding type menu gt Hard Disk Drives This feature allows you to specify the boot sequence from the list of available hard disk drives A device that is in parenthesis has been disabled in the corresponding type menu gt CD DVD Drives This feature allows you to specify the boot sequence from the list of available CD DVD drives A device that is in parenthesis has been disabled in the corresponding type menu Retry Boot Devices This option allows you to retry boot devices Options include Enabled and Disabled 7 6 Exit Menu Select the Exit tab from AMI BIOS Setup Utility screen to enter the Exit BIOS Setup screen Save Changes and Exit When you have complete
17. POST Chapter 7 BIOS Watch Dog Function Allows system to restart when system is inactive more than 5 minutes The options are Enabled and Disabled Power Button Function This sets the function of the power button when you turn off the system Options include 4 second Overide and Instant Off Restore on AC Power Loss This sets the action that occurs when an AC power loss occurs Options include Power Off Power On and Last State Interrupt 19 Capture Select Enabled to allow ROMs to trap Interrupt 19 The options are Enabled and Disabled EUP Support This setting allows you to enable or disable supplied standby power in S5 Set to Enabled to for EUP requirements and set to Disabled for wakening capability gt Processor and Clock Options CPU Configuration This displays static information on the Module Version Physical Count and Logical Count for the system s processor s and clock CPU Information The information for the installed processor includes Revision Cache L1 L2 L3 Speed NB CLK Able to Change Frequency and uCode Patch Level GART Error Reporting This option should remain disabled for normal operation The driver developer may enable this option for testing purposes Options are Enabled or Disabled Microcode Update This setting Enables or Disables microcode updating Secure Virtual Machine Mode This setting is used to Enable or Disable SVM Power Now This setting is used to Enable or Disable the
18. and pushed fully into the rack which is its normal position Secondly these tabs also lock the server in place when fully extended from the rack This prevents the server from coming completely out of the rack when you pull it out for servicing Figure 2 2 Installing the Rack Rails 2 5 SUPERSERVER 1022G NTF User s Manual Installing the Server into the Rack You should now have rails attached to both the chassis and the rack unit The next step is to install the server into the rack Do this by lining up the rear of the chassis rails with the front of the rack rails Slide the chassis rails into the rack rails keeping the pressure even on both sides you may have to depress the locking tabs when inserting See Figure 2 3 for details When the server has been pushed completely into the rack you should hear the locking tabs click Figure 2 3 Installing the Server into a Rack 2 6 Chapter 2 Server Installation Installing the Server into a Telco Rack To install the 1022G NTF into a Telco type rack use two L shaped brackets on either side of the chassis four total First determine how far follow the server will extend out the front of the rack Larger chassis should be positioned to balance the weight between front and back If a bezel is included on your server remove it Then atta
19. ductive harm Manual Revision 1 0 Release Date April 22 2010 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2010 by Super Micro Computer Inc All rights reserved Printed in the United States of America Preface Preface About This Manual This manual is written for professional system integrators and PC technicians It provides information for the installation and use of the SuperServer 1022G NTF In stallation and maintenance should be performed by experienced technicians only The SuperServer 1022G NTF is a 1U rackmount server based on the SC815TQ 563UBP server chassis and the Super H8DGU F serverboard Please refer to our web site for updates on supported processors Manual Organization Chapter 1 Introduction The first chapter provides a checklist of the main components included with the server system and describes the main features of the Super H8DGU F serverboard and the SC815TQ 563UBP chassis Chapter 2 Server Installation This chapter describes the steps necessary to install the SuperServer 1022G NTF into a rack and check out the server configuration prior to powering up the system If your server was ordered without
20. in the drive bays to maintain proper airflow 6 5 SUPERSERVER 1022G NTF User s Manual Installing Removing a Hard Drive 1 To remove a carrier push the release button located beside the drive LEDs 2 Swing the colored handle fully out and use it to pull the unit straight out see Figure 6 5 Note Your operating system must have RAID support to enable the hot plug ca pability of the hard drives Figure 6 5 Removing a Hard Drive from the Server DVD ROM Drive Installation The top cover of the chassis must be opened to gain full access to the DVD ROM drive bay The 1022G NTF accomodates only slim line DVD ROM drives Side mounting brackets are needed to mount a slim line DVD ROM drive in the 1022G NTF server You must power down the system before installing or removing a DVD ROM drive Removing the Chassis Cover 1 Grasp the two handles on either side and pull the unit straight out until it locks you will hear a click 6 6 Chapter 6 Advanced Chassis Setup 2 Depress the two buttons on the top of the chassis to release the top cover and at the same time push the cover away from you until it stops You can then lift the top cover from the chassis to gain full access to the inside of the server Removing Installing a Drive 1 With the chassis cover removed unplug the power and data cables from the drive you want to remove 2 Locate the locking tab at the rear of the drive It will be on the left sid
21. the COM2 header See the table on the right for pin definitions USBO Pin 4 Definition 1 45V 2 PO Universal Serial Bus Ports Pin Definitions USB0 1 USB6 USB1 Pin Definition 1 5V PO 2 3 PO 3 PO Universal Serial Bus Headers Pin Definitions USB4 5 USB2 USB3 Pin Definition Pin Definition 1 5V 1 5V 2 PO 2 PO 3 PO 3 PO 4 Ground 4 Ground 5 Key 5 NC Note NC indicates no connection Fan Header Pin Definitions Pin Definition Ground 12V ro Tachometer 4 PWR Modulation Serial Port Pin Definitions COM1 COM2 Pin Definition Pin Definition 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 Ground 10 NC Note NC indicates no connection SUPERSERVER 1022G NTF User s Manual T SGPIO SGPIO Header Pin Definitions The T SGPIO1 T SGPIO2 Serial General ESGPIONT SGPIO2 Purpose Input Output headers provide a _Pin Definition Pin Definition bus between the SATA controller and the backpane to provide SATA enclosure man agement functions Connect the appropriate Ground cable from the backplane to the T SGPIO1 header to utilize SATA management func Note NC indicates no connection tions on your system UIO Power Connector UIO Power Connector A Universal I O UIO Power connector is Pin Definitions UIOP located next to the UID switch Connect this Pin Definition Pin Definit
22. the CPU and the heatsink removing the used thermal rmal grease on the surface before Chapter 5 Advanced Serverboard Setup 5 3 Connecting Cables Now that the processors are installed the next step is to connect the cables to the serverboard These include the data ribbon cables for the peripherals and control panel and the power cables Connecting Data Cables The cables used to transfer data from the peripheral devices have been carefully routed in preconfigured systems to prevent them from blocking the flow of cooling air that moves through the system from front to back If you need to disconnect any of these cables you should take care to reroute them as they were originally after reconnecting them make sure the red wires connect to the pin 1 locations If you are configuring the system keep the airflow in mind when routing the cables The following data cables with their serverboard connector locations noted should be connected See the serverboard layout diagram in this chapter for connector locations e DVD ROM drive cable SATA4 SATA cables SATAO SATA3 e Control Panel cable JF1 see next page Connecting Power Cables The H8DGU F has a 20 pin primary power supply connector designated JPW1 for connection to the ATX power supply Connect the appropriate connector from the power supply to JPW1 to supply power to the serverboard See the Connector Definitions section in this chapter for power connector pin
23. the processor and memory components this chap ter will refer you to the appropriate sections of the manual for their installation Chapter 3 System Interface Refer to this chapter for details on the system interface which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system Chapter 4 System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SuperServer 1022G NTF Chapter 5 Advanced Serverboard Setup This chapter provides detailed information on the H8DGU F serverboard including the locations and functions of connectors headers and jumpers Refer to this chap ter when adding or removing processors or main memory and when reconfiguring the serverboard SUPERSERVER 1022G NTF User s Manual Chapter 6 Advanced Chassis Setup Refer to Chapter 6 for detailed information on the SC815TQ 563UBP chassis You should follow the procedures given in this chapter when installing removing or reconfiguring Serial ATA or peripheral drives and when replacing system power supply units and cooling fans Chapter 7 BIOS The BIOS chapter includes an introduction to BIOS and provides detailed informa tion on running the CMOS Setup Utility Appendix A BIOS POST Error Codes Appendix B Installing Windows Appendix C System Specifications
24. 18 Compact Flash Card PWR Connector ssseseeesseeeesereseerreeeerrererirresrrrresne 5 18 5 9 Jumper le CN 5 19 Explanation of Tier 5 19 CMOS e 5 19 12C to PCI Express eege 5 20 Watch Dog Enable Disable eseegsbergeseegeebitte ege ben en pan ead CekRegecesght 5 20 LAN1 2 Enable Disable i 1 iir reae ora Eee er E ER Ente ea repas 5 20 VGA Enable Disable nennen 5 20 5 10 Onboard IndiIGaltors ondes conve oe Ee ia HE DO dne ERR Hd Dv a Eau as NE as 5 21 IR ME LEDS C M 5 21 Dedicated IPMI LAN LEIDs nnne 5 21 Table of Contents 5 11 5 12 5 13 6 1 6 2 6 3 6 4 6 5 7 1 7 2 7 3 7 4 7 5 VID EEDE perme ee TS 5 21 Power DR EE 5 21 SATA Drive RENE 5 22 HE WE 5 22 Enabling SATA RE 5 23 Serial ATA GATAIL ener sheer nnne nnns nennen 5 23 Installing the OS SATA KI 5 23 Building a Driver Diskette sis s ion entere 5 23 Enabling SATA RAID in the BIOG 5 24 Using the Adaptec RAID Utility xc sierra rrr prende to xus centeescdelediesacstanes 5 25 Installing the RAID Driver During OS Installation 5 25 MVS TANNING RTE 5 26 S per BJ e7e4 A uec ree 5 27 Chapter 6 Advanced Chassis Setup Static Sensitive DU s ee EE 6 1 ee EE 6 1 Control Eelere eege 6 2 System Fans eege et 6 2 System Fan Ne 6 3 Drive Bay Installatior PiemoVval icu iiia etae gp Eo ttu leise e eege 6 4 Removing the Front Bezel 5 gere aphids dahi
25. 2G NTF User s Manual Note You need to have an external USB floppy when building the driver diskette Window s Vista Windows 2008 or later Windows OS systems can use a USB stick instead of a floppy Enabling SATA RAID in the BIOS Before installing the Windows Operating System you must change some settings in BIOS Boot up the system and hit the Del key to enter the BIOS Setup Ullility After the Setup Utility loads 1 Use the arrow keys to move to the Exit menu Scroll down with the arrow keys to the Load Optimal Defaults setting and press Enter Select OK to confirm then Enter to load the default settings 2 Use the arrow keys to move to the Advanced menu then scroll down to Chipset Configuration Next enter SourthBridge Configuration and press the Enter key Once in this submenu scroll down to OnChip SATA Type and choose the RAID option see Figure 5 5 Figure 5 5 BIOS Setup Screen BIOS SETUP UTILITY Advanced SouthBridge Chipset Configuration B700 CIMx Version 5 0 2 Native IDE e LIO DUI O OHCI HC Bus 0 Deu 18 Fn 0 Enabled AMD_AHCI OHCI HC BusO Deu 18 Fn 1 Enabled EHCI HC BusO Deu 18 Fn 2 Options OHCI HC BusO Deu 19 Func 0 BhFISUT N UD OHCI HC Bus 0 Deu 19 Func 1a EHCI HC Bus 0 Dev 19 Fn 2 RETER OHCI HC Bus 0 Dev 20 Fn 5 e Select Screen OnChip SATA Chamel Select Item Change Option SATA IDE Combined Mode Enabled General Help PATA Channel Conf
26. Because of their hotswap capability you do not need to access the inside of the chassis or power down the system to install or replace SATA drives Proceed to the next section for instructions DVD ROM Drive For installing removing a DVD ROM drive you will need to gain access to the inside of the 1022G NTF by removing the top cover of the chassis Proceed to the DVD ROM Drive Installation section later in this chapter for instructions Note Only a slim DVD ROM drive will fit into the 1022G NTF 6 4 Chapter 6 Advanced Chassis Setup Hard Drive Installation The hard drives are mounted in drive carriers to simplify their installation and removal from the chassis These carriers also help promote proper airflow for the drive bays For this reason even empty carriers without drives installed must remain in the chassis Mounting a Hard Drive in a Drive Carrier 1 Insert a drive into the carrier with the printed circuit board side facing down so that the mounting holes align with those in the carrier 2 Secure the drive to the carrier with six screws as shown in Figure 6 4 Figure 6 4 Mounting a Hard Drive in a Carrier Use caution when working around the hard drive backplane Do not touch the backplane with any metal objects and make sure no ribbon cables touch the backplane or obstruct the holes which aid in proper airflow Important Regardless of how many hard drives are installed all drive car riers must remain
27. Chip SATA Channel This setting allows you to Enable or Disable the OnChip SATA channel On Chip SATA Type Use this setting to set the On Chip SATA type Options include Native IDE RAID AMD AHCI and Legacy IDE SATA IDE Combined Mode This setting allows you to Enable or Disable the SATA IDE combined mode PATA Channel Configuration This allows you to set PATA channel configuration Options include SATA as Primary or SATA as secondary gt Primary Secondary Third Fourth IDE Master Slave LBA Large Mode LBA Logical Block Addressing is a method of addressing data on a disk drive The options are Disabled and Auto Block Multi Sector Transfer Block mode boosts IDE drive performance by increasing the amount of data transferred Only 512 bytes of data can be transferred per interrupt if block mode is not used Block mode allows transfers of up to 64 KB per interrupt Select Disabled to allow the data to be transferred from and to the device one sector at a time Select Auto to allows the data transfer from and to the device occur multiple sectors at a time if the device supports it The options are Auto and Disabled Chapter 7 BIOS PIO Mode PIO Programmable I O mode programs timing cycles between the IDE drive and the programmable IDE controller As the PIO mode increases the cycle time decreases The options are Auto 0 1 2 3 and 4 Select Auto to allow BIOS to auto detect the PIO mode Use this value if
28. LED will remain flashing or on as long as the indicated condition exists See the table below for descriptions of the LED states Figure 3 1 Universal Information LED States Universal Information LED States State Indication Fast Blinking Red 1x sec Fan Fail Solid Red CPU Overheat Slow Blinking Red 1x 4 sec Power Fail Solid Blue Local UID Button Depressed Blinking Blue IPMI Activated UID 3 2 Chapter 3 System Interface Note deactivating the UID LED must be performed in the same way it was activated If the UID LED was activated via IPMI you can only turn the LED off via IPMI and not with the UID button EZ NIC2 Indicates network activity on LAN2 when flashing ZS NIC Indicates network activity on LAN1 when flashing R HDD On the SuperServer 1022G NTF this light indicates SATA and or DVD ROM drive activity when flashing e a 9 gt Power Indicates power is being supplied to the system s power supply units This LED should normally be illuminated when the system is operating 3 3 SUPERSERVER 1022G NTF User s Manual 3 4 Hard Drive Carrier LEDs Each hard drive carrier has two LEDs e Green When illuminated the green LED on the front of the drive carrier indi cates drive activity A connection to the drive backplane enables this LED to blink on and off when that particular drive is being accessed Red The red LED indicates two states When blinking it indicate
29. OM drive DVM PNSC DVD SBT or DVM TEAC DVD SBT One 1 DVD ROM drive cable CBL 00341L Four 4 sets of 4 cm counter rotating fans FAN 0086L4 One 1 air shroud MCP 310 18002 0N Two 2 passive CPU heatsinks SNK P0042P One 1 RSC R1UU 2E8 for PCI E card see Section 5 6 for details SATA Accessories One 1 SATA backplane BPN SAS 815TQ One 1 SATA Set of 4 43 33 26 22 cm Round cable CBL 0190L One 1 40 cm 8 pin to 8 pin ribbon cable with tube for SGPIO CBL 0157L One 1 rackmount kit CSE PT51L One 1 CD containing drivers and utilities SuperServer 1022G NTF User s Manual 1 1 SUPERSERVER 1022G NTF User s Manual 1 2 Serverboard Features At the heart of the SuperServer 1022G NTF lies the H8DGU F a dual processor serverboard based on the AMD SR5670 SP5100 chipset Below are the main features of the H8DGU F See Figure 1 1 for a block diagram of the chipset Processors The H8DGU F supports single or dual AMD Opteron 6100 Series processors in Socket G34 type sockets Please refer to our web site for a complete listing of supported processors www supermicro com Memory The H8DGU F has sixteen single dual tri quad channel 240 pin DIMM sockets that can support up to 256GB of DDR3 1333 1066 800MHz registered ECC SDRAM or 64 GB of DDR3 1333 1066 800 MHz unbuffered ECC non ECC SDRAM Please refer to Chapter 5 for installing memory UIO The H8DGU F is a specially designed serverboard that features S
30. SUPERG SUPERSERVER 1022G NTF USER S MANUAL The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software and docu mentation is the property of Supermicro and or its licensors and is supplied only under a license Any use or reproduction of this product is not allowed except as expressly permitted by the terms of said license IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between
31. activates the other options for user setting DRAM ECC Enable This setting allows hardware to report and correct memory errors au tomatically maintaining system integrity Options are Enabled or Dis abled This is option is only active if ECC Mode above is set to User gt DRAM Timing Configuration DRAM Timing Config This option allows you to set the DRAM timing configuration for the system Options include Auto or Manual Memory Timing Parameters This selects the which node s timing parameters to display Options are CPU Node 0 or CPU Node 1 IOMMU This setting is used to enable or disable or set the GART size in systems without AGP Options include Enabled and Disabled OHCI EHCI HC Device Functions These settings allow you to either Enable or Disable functions for OHCI or EHCI bus devices USB 2 0 Controller Mode Use this setting to configure the USB 2 0 Controller in either Hi Speed 480 Mps or Full Speed 12 Mps mode Options include Enabled Hi Speed Mode or Disabled Full Speed Mode SUPERSERVER 1022G NTF User s Manual Legacy USB Support Select Enabled to enable the support for USB Legacy Disable Legacy support if there are no USB devices installed in the system Auto disabled Legacy support if no USB devices are connected The options are Disabled Enabled and Auto gt IDE Configuration Onboard PCI IDE Controller This setting allows you to Enable or Disable the PCI IDE controller On
32. address and Interrupt Request address of serial port 1 Select Disabled to prevent the serial port from accessing any system resources When this option is set to Disabled the serial port physically becomes unavailable Select 3F8 IRQ4 to allow the serial port to use 3F8 as its I O port address and IRQ 4 for the interrupt address Options include Disabled 3F8 IRQ4 3E8 IRQ4 and 2E8 IRQ3 Serial 2 Address This option specifies the base I O port address and Interrupt Request address of serial port 2 Select Disabled to prevent the serial port from accessing any system resources When this option is set to Disabled the serial port physically becomes unavailable Select 2F8 IRQ3 to allow the serial port to use 2F8 as its I O port address and IRQ 3 for the interrupt address Options include Disabled 2F8 IRQ3 3E8 IRQ4 and 2F8 IRQ3 Serial Port 2 Attribute This option allows you to set COM2 as a normal serial port or as virtual COM for SOL Options are SOL or COM gt Remote Access Configuration Remote Access Use this option to Enable or Disable Remote Access in your system If enabled the settings below will appear Serial Port Number Use this setting to select the serial port for console redirection Options include COM 1 COM2 The displayed base address and IRQ for the serial port changes to reflect the selection you make Note Make sure the selected port is enabled Serial Port Mode Selects the serial port setting
33. attery may release hazardous materials into the envi ronment Do not discard a used battery in the garbage or a public landfill Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly Please handle used batteries carefully Do not damage the battery in any 4 4 Chapter 5 Advanced Serverboard Setup Chapter 5 Advanced Serverboard Setup This chapter covers the steps required to install processors and heatsinks to the H8DGU F serverboard connect the data and power cables and install add on cards All serverboard jumpers and connections are described and a layout and quick reference chart are included in this chapter Remember to close the chas sis completely when you have finished working on the serverboard to protect and cool the system sufficiently 5 1 Handling the Serverboard Static electrical discharge can damage electronic components To prevent damage to printed circuit boards it is important to handle them very carefully see Chapter 4 Also note that the size and weight of the serverboard can cause it to bend if handled improperly which may result in damage To prevent the serverboard from bending keep one hand under the center of the board to support it when handling The following measures are generally sufficient to protect your equipment from static discharge Precautions Use a grounded wrist strap designed to prevent static discharge
34. ause electrical shock Use extreme caution when using metal tools which can easily damage any electrical components or circuit boards they come into contact with Do not use mats designed to decrease static electrical discharge as protection from electrical shock Instead use rubber mats that have been specifically designed as electrical insulators 4 1 SUPERSERVER 1022G NTF User s Manual e The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets This product may be connected to an IT power system In all cases make sure that the unit is also reliably connected to Earth ground e Serverboard Battery CAUTION There is a danger of explosion if the onboard battery is installed upside down which will reverse its polarites see Figure 4 1 This battery must be replaced only with the same or an equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions e DVD ROM Laser CAUTION this server may have come equipped with a DVD ROM drive To prevent direct exposure to the laser beam and hazardous radiation exposure do not open the enclosure or use the unit in any uncon ventional way e Mainboard replaceable soldered in fuses Self resetting PTC Positive Tempera ture Coefficient fuses on the mainboard must be replaced by trained service technicians only The new fuse must be the same or equivalent as the one re
35. ch the two front brackets to each side of the chassis then the two rear brackets positioned with just enough space to accommodate the width of the telco rack Finish by sliding the chassis into the rack and tightening the brackets to the rack Figure 2 4 Installing the Server into a Telco Rack le 0 00 000 0 00 000 0000000000 00000 000000 000 000000 000000000000 EE EE E 2 7 SUPERSERVER 1022G NTF User s Manual 2 5 Checking the Serverboard Setup After you install the 1022G NTF in the rack you will need to open the top cover to make sure the serverboard is properly installed and all the connections have been made Accessing the Inside of the System 1 First grasp the two handles on either side and pull the system straight out until it locks you will hear a click Depress the two buttons on the top of the chassis to release the top cover 1 Push the cover away from you toward the rear of the chassis until it stops 2 You can then lift the top cover from the chassis to gain full access to the inside of the server See Figure 2 5 To remove the system from the rack completely depress the locking tabs in the chassis rails push the right side tab down and the left side tab up to continue to pull the system out past the locked position Checking the Components 1 You may have one or two processors already installed in the serverboard Each processor needs its own heat
36. d the system configuration changes select this option to leave BIOS Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Exit from the Exit menu and press lt Enter gt Discard Changes and Exit Select this option to quit BIOS Setup without making any permanent changes to the system configuration and reboot the computer Select Discard Changes and Exit from the Exit menu and press lt Enter gt Discard Changes Select this option and press lt Enter gt to discard all the changes and return to AMI BIOS Utility Program 7 14 Chapter 7 BIOS Load Optimal Defaults To set this feature select Load Optimal Defaults from the Exit menu and press lt Enter gt Then Select OK to allow BIOS to automatically load the Optimal Defaults as the BIOS Settings The Optimal settings are designed for maximum system performance but may not work best for all computer applications Load Fail Safe Defaults To set this feature select Load Fail Safe Defaults from the Exit menu and press lt Enter gt The Fail Safe settings are designed for maximum system stability but not maximum performance 7 15 SUPERSERVER 1022G NTF User s Manual Notes Appendix A BIOS Error Beep Codes Appendix A BIOS Error Beep Codes During the POST Power On Self Test routines which are performed each time the system is powered on errors may occur Non fatal errors are those which in
37. definitions In addition your power supply must be connected to the 8 pin Processor Power connectors at JPW2 and JPW3 Connecting the Control Panel JF1 contains header pins for various front control panel connectors See Figure 5 1 for the pin locations of the various front control panel buttons and LED indica tors Please note that even and odd numbered pins are on opposite sides of each header All JF1 wires have been bundled into single keyed ribbon cable to simplify their connection The red wire in the ribbon cable plugs into pin 1 of JF1 Connect the other end of the cable to the Control Panel printed circuit board located just behind the system status LEDs in the chassis 5 5 SUPERSERVER 1022G NTF User s Manual See the Connector Definitions section in this chapter for details and pin descrip tions of JF1 Figure 5 1 Front Control Panel Header Pins JF1 20 19 5 4 UO Ports The I O ports are color coded in conformance with the PC 99 specification See Figure 5 2 below for the colors and locations of the various I O ports Figure 5 2 Rear Panel UO Ports o Li o Chapter 5 Advanced Serverboard Setup 5 5 Installing Memory CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage Memory Support The H8DGU F supports up to 256GB of DDR3 1333 1066 800MHz registered ECC SDRAM or 64 GB of DDR3
38. delivered it Decide on a suitable location for the rack unit that will hold the 1022G NTF It should be situated in a clean dust free area that is well ventilated Avoid areas where heat electrical noise and electromagnetic fields are generated You will also need it placed near a grounded power outlet Be sure to read the Rack and Server Precautions in the next section 2 3 Preparing for Setup The box the SuperServer 1022G NTF was shipped in should include two sets of rail assemblies two rail mounting brackets and the mounting screws you will need to install the system into the rack Follow the steps in the order given to complete the installation process in a minimum amount of time Please read this section in its entirety before you begin the installation procedure outlined in the sections that follow 2 1 SUPERSERVER 1022G NTF User s Manual Choosing a Setup Location Leave enough clearance in front of the rack to enable you to open the front door completely 25 inches and approximately 30 inches of clearance in the back of the rack to allow for sufficient airflow and ease in servicing This product is for installation only in a Restricted Access Location dedicated equipment rooms service closets and the like e This product is not suitable for use with visual display work place devices acccording to 2 of the the German Ordinance for Work with Visual Display Units N Warnings and Precautions N Rack Precautions
39. deration should be given to installing the equipment in an environment compatible with the manufacturer s maximum rated ambient temperature Tmra Reduced Airflow Equipment should be mounted into a rack so that the amount of airflow required for safe operation is not compromised Mechanical Loading Equipment should be mounted into a rack so that a hazardous condition does not arise due to uneven mechanical loading Circuit Overloading Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern Reliable Ground A reliable ground must be maintained at all times To ensure this the rack itself should be grounded Particular attention should be given to power supply connections other than the direct connections to the branch circuit i e the use of power strips etc 2 3 SUPERSERVER 1022G NTF User s Manual 2 4 Installing the System into a Rack This section provides information on installing the 1022G NTF into a rack unit with the rack rails provided If the system has already been mounted into a rack you can skip ahead to Sections 2 5 and 2 6 There are a variety of rack units on the market which may mean the assembly procedure will differ slightly You should also ref
40. e of the drive when viewed from the front of the chassis 3 Pull the tab away from the drive and push the drive unit out the front of the chassis 4 Add anew drive by following this procedure in reverse order You may hear a faint click of the locking tab when the drive is fully inserted 5 Remember to reconnect the data and power cables to the drive before replacing the chassis cover and restoring power to the system 6 5 Power Supply The SuperServer 1022G NTF has a 560 watt redundant power supply configuration consisting of two hot swap power modules The power supply modules have an auto switching capability which enables them to automatically sense and operate with a 100V 240V input voltage Power Supply Failure If either of the two power supply modules fail the other module will take the full load and allow the system to continue operation without interruption The Universal Information LED on the control panel will blink slowly and remain so until the failed module has been replaced Replacement modules can be ordered directly from Supermicro see contact information in the Preface The power supply modules have a hot swap capability meaning you can replace the failed module without powering down the system 6 7 SUPERSERVER 1022G NTF User s Manual Replacing the Power Supply You do not need to shut down the system to replace a power supply module The redundant feature will keep the system up and running while
41. er rate from 150 MBps The serial cables used in SATA are thinner than the traditional cables used in Parallel ATA PATA and can extend up to one meter in length compared to only 40 cm for PATA cables Overall SATA provides better functionality than PATA Installing the OS SATA Driver Before installing the OS operating system and SATA RAID driver you must decide if you wish to have the operating system installed as part of a bootable RAID array or installed to a separate non RAID hard drive If on a separate drive you may install the driver either during or after the OS installation If you wish to have the OS on a SATA RAID array you must follow the procedure below and install the driver during the OS installation Building a Driver Diskette You must first build a driver diskette from the Supermicro CD ROM that was included with the system You will have to create this disk on a computer that is already running and with the OS installed Building a Driver Diskette 1 Insert the CD into your CD ROM drive and start the system A display as shown in Figure 5 7 will appear 2 Click on the icon labeled Build Driver Diskettes and Manuals and follow the instructions to create a floppy disk with the driver on it 3 Once it s been created remove the floppy and insert the installation CD for the Windows Operating System you wish to install into the CD ROM drive of the new system you are about to configure 5 23 SUPERSERVER 102
42. er to the installation instructions that came with the rack unit you are using Identifying the Sections of the Rack Rails You should have received two rack rail assemblies in the rack mounting kit Each assembly consists of two sections an inner fixed chassis rail that secures directly to the server chassis and an outer fixed rack rail that secures directly to the rack itself see Figure 2 1 Two pairs of short brackets to be used on the front side of the outer rails are also included Installing the Inner Rails Both the left and right side inner rails have been pre attached to the chassis Proceed to the next step Figure 2 1 Identifying the Sections of the Rack Rails right side rail shown Inner Rail pre installed 2 4 Chapter 2 Server Installation Installing the Outer Rails Begin by measuring the distance from the front rail to the rear rail of the rack Attach a short bracket to the front side of the right outer rail and a long bracket to the rear side of the right outer rail Adjust both the short and long brackets to the proper distance so that the rail can fit snugly into the rack Secure the short bracket to the front side of the outer rail with two screws and the long bracket to the rear side of the outer rail with three screws Repeat these steps for the left outer rail Locking Tabs Both chassis rails have a locking tab which serves two functions The first is to lock the server into place when installed
43. etailer immediately Refer to the Supermicro web site for updates on CPU support Installing the Processors 1 Begin by removing the cover plate that protects the CPU Lift the lever on the CPU socket until it points straight up 2 With the lever raised lift open the silver CPU retention plate 5 2 Chapter 5 Advanced Serverboard Setup 3 Use your thumb and your index finger to hold the CPU Locate and align pin 1 of the CPU socket with pin 1 of the CPU Both are marked with a triangle 4 Align pin 1 of the CPU with pin 1 of the socket Once aligned carefully place the CPU into the socket Do not drop the CPU on the socket move the CPU horizontally or vertically or rub the CPU against the socket or against any pins of the socket which may damage the CPU and or the socket 5 With the CPU inserted into the socket inspect the four corners of the CPU to make sure that it is properly installed and flush with the socket Then gently lower the silver CPU retention plate into place 6 Carefully press the CPU socket lever down until it locks into its retention tab For a dual CPU system repeat these steps to install another CPU into the CPU 2 socket and into CPU 2 3 and 4 sockets for a quad CPU configura tion Note in single and dual CPU configurations memory must be installed in the DIMM slots associated with the installed CPU s Memory is limited to a maximum of 32 GB for a single CPU and 64 GB f
44. f the chassis for easy system location in large stack configurations The LED will remain on until the button is pushed a second time Another UID button on the rear of the chassis serves the same function RESET Reset Use the reset button to reboot the system 3 1 SUPERSERVER 1022G NTF User s Manual Power The main power button is used to apply or remove power from the power supply to the server system Turning off system power with this button removes the main power but keeps standby power supplied to the system 3 3 Control Panel LEDs The control panel located on the front of the SC815TS R560U SC815TS 560UBP chassis has five LEDs These LEDs provide you with critical information related to different parts of the system This section explains what each LED indicates when illuminated and any corrective action you may need to take Universal Information LED When this LED blinks red quickly it indicates a fan failure and when blinking red slowly a power failure The LED will be blue when used for UID Unit Identifier When on continuously it indicates an overheat condition which may be caused by cables obstructing the airflow in the system or the ambient room temperature being too warm Check the routing of the cables and make sure all fans are present and operating normally You should also check to make sure that the chassis covers are installed Finally verify that the heatsinks are installed properly see Chapter 5 This
45. for the chipset 2 MB 3 99 GB I O APIC 4 Kbytes 4 KB 3 99 GB PCI Enumeration Area 1 256 MB 3 76 GB PCI Express 256 MB 256 MB 3 51 GB PCI Enumeration Area 2 if needed Aligned on 256 M boundary Memory available for the OS amp other applications 2 84 GB 5 9 SUPERSERVER 1022G NTF User s Manual 5 6 Adding PCI Cards PCI Expansion Slots Riser cards are used to support add on cards to the system Installing a PCI Expansion Card 1 Confirm that you have the correct riser card for your chassis model and the add on card includes a standard bracket 2 Remove the chassis cover 3 Install the riser card by sliding card into the appropriate riser card in the motherboard 4 Choose the PCI slot shield in which to place the add on card 5 In that slot open the PCI slot shield lever and slide the shield sideways 6 From inside the chassis remove the PCI slot shield 7 Slide the add on card into the riser card and attach the add on card bracket in place of the PCI slot shield 8 Secure the add on card by closing the PCI slot shield lever 9 Connect cables to the add on card as necessary 5 10 Chapter 5 Advanced Serverboard Setup 5 7 Serverboard Details Figure 5 4 SUPER H8DGU F Layout not drawn to scale UID
46. g System Cooling Four 4 4 cm heavy duty counter rotating fans System Input Requirements AC Input Voltage 100 240 VAC Rated Input Current 8A 115V to 4A 230V Rated Input Frequency 50 60 Hz Power Supply Rated Output Power 560W Model PWS 563 1H Rated Output Voltages 5V 18A 3 3V 15A 12V 49A 5Vsb 3A Operating Environment Operating Temperature 10 to 35 C 50 to 95 F Non operating Temperature 40 to 70 C 40 to 158 F Operating Relative Humidity 8 to 90 non condensing Non operating Relative Humidity 5 to 95 non condensing C 2 Appendix C System Specifications Regulatory Compliance Electromagnetic Emissions FCC Class A EN 55022 Class A EN 61000 3 2 3 3 CISPR 22 Class A Electromagnetic Immunity EN 55024 CISPR 24 EN 61000 4 2 EN 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 EN 61000 4 8 EN 61000 4 11 Safety CSA EN IEC UL 60950 1 Compliant UL or CSA Listed USA and Canada CE Marking Europe California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate C 3 SUPERSERVER 1022G NTF User s Manual continued from front The products sold by Supermicro are not intended for and will not be used in life support systems medical equi
47. ig SATA as primary Save and Exit ESC Exit Power Saving Features Disabled v02 61 C Copyright 1985 2006 American Megatrends Inc 3 Hit the lt Esc gt key twice and scroll to the Exit menu Select Save Changes and Exit and hit lt enter gt then hit lt Enter gt again to verify 5 24 Chapter 5 Advanced Serverboard Setup 1 After exiting the BIOS Setup Utility the system will reboot When prompted during the startup press the lt CTRL A gt key when prompted to run the Dot Hill RAID Utility program see Figure 5 6 Figure 5 6 Adaptec RAID Utility Program Screen anage Arrays reate Array dd Delete Hotspare Configure Drives Using the Adaptec RAID Utility The Adaptec RAID Utility program is where you can define the drives you want to include in the RAID array and the mode and type of RAID Installing the RAID Driver During OS Installation You may also use the procedure below to install the RAID driver during the Win dow s OS installation 1 With the Windows OS installation CD in the CD ROM drive restart the sys tem 2 When you see the prompt hit the lt F6 gt key to enter Windows setup 3 Eventually a blue screen will appear with a message that begins Windows could not determine the type of one or more storage devices When you see the screen hit the lt S gt key to Specify Additional Device then insert the driver diskette you just created into the floppy drive 4 Highligh
48. inistration ms Management Report Help a Health Information Intrusion CPUL Chassis CPU2 Chassis 5 27 SUPERSERVER 1022G NTF User s Manual Figure 5 9 Supero Doctor Ill Interface Display Screen Remote Control E Supero Doctor III Microsoft Internet Explorer 3 8 xl File Edit view Favorites Tools Help Sc Ree Ls FSuper Docior III TIED cmm Remote Management DEE System Info Health Info Performance Remote Control Configuration Administration Systems Managerment Report Help Remote Control Graceful power control Supero Doctor III allows a user to inform the OS to reboot or shut down within a specified time the default is 30 seconds Before the system reboots or shuts down it s allowed to cancel the action Requirements Keep Supero SD3Service Daemon running at all times on this system Provide TCP IP connectivity Power control Note Super Doctor Ill Software Revision 1 0 can be downloaded from our Web Site at ftp ftp supermicro com utility Supero_Doctor_Ill You can also down load the Super Doctor III User s Guide at lt http www supermicro com PROD UCT Manuals SDIII UserGuide pdf gt For Linux we recommend that you use the Supero Doctor II applictation instead 5 28 Chapter 5 Advanced Serverboard Setup Notes 5 29 Chapter 6 Advanced Chassis Setup Chapter 6 Advanced Chassis Setup This chapter covers the steps required to in
49. ion connector to the power supply to provide ad SVELI equate power to the UIO device installed on we 2 the slot for this device to function properly B3 95V 3 Ai 3V3 3 B6 5V 6 AG 3V3 6 B7 5V_7 A7 S B9 DN 9 A9 E B10 Ee 3V3_10 B13 3V3_STBY A13 P12V_2 B14 GND A14 P12V sw ow avs Tea B16 GND 1 A16 P12V Bim GND_2 A17 P12V B18 GND 3 GND 7 LAN1 2 Ethernet Ports Two Gigabit Ethernet ports designated LAN1 and LAN2 are located beside the VGA port Additionally for the H8DGU F serverboard there is a dedicated LAN for IPMI on top of the two rear USB ports These Ethernet ports accept RJ45 type cables Chapter 5 Advanced Serverboard Setup Chassis Intrusion Chassis Intrusion Pin Definitions JL1 Pin Definition a chassis intrusion 1 Battery voltage 2 Intrusion signal A Chassis Intrusion header is located at JL1 Attach the appropriate cable to inform you of Overheat LED Overheat LED Connect an LED to the JOH1 header to pro Rin Definitions JOH1 vide warning of chassis overheating See the m Pin Definition table on the right for pin definitions 1 3 3V 2 OH Active Power LED Speaker PWR LED Connector Pin Definitions On the JD1 header pins 1 3 are used for ee Pin Setting Definiti power LED indication and pins 4 7 are for Ee the speaker See the tables on the right for d SE pin definitions If you wish to use the onboard di
50. irflow 1 Airflow is provided by four sets of 4 cm fans each set of fans consists of two fans that are mounted back to back The system component layout was carefully designed to direct sufficient cooling airflow to the components that generate the most heat Note that all power and data cables have been routed in such a way that they do not block the airflow generated by the fans Providing Power 1 The last thing you must do is to provide input power to the system Plug the power cords from the power supply modules into a high quality power strip that offers protection from electrical noise and power surges It is recommended that you use an uninterruptible power supply UPS 2 10 Chapter 3 System Interface Chapter 3 System Interface 3 1 Overview There are several LEDs on the control panel as well as others on the SATA drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specific components There are also two buttons on the chassis control panel and an on off switch on the power supply This chapter explains the meanings of all LED indicators and the appropriate response you may need to take 3 2 Control Panel Buttons There are three push buttons located on the front of the chassis a reset button a UID button and a power on off button Q UID Depressing the UID unit identifier button illuminates an LED on both the front and rear o
51. l 6 4 Accessing the Drive Bay Szansa aii 6 4 Hard Drive rui u C 6 5 DVD ROM Drive TnstallatiDFl cuan eue Ruo E ebur Eua FE n Rte R n enisuESEE 6 6 Power SUD secs ee een eT eee ener eC tute rer ee eee tor toS eee 6 7 Power Supply EIERE 6 7 Chapter 7 BIOS ege ee EE 7 1 Starting the Setup RRE 7 1 Mai MENU scassi asenn annaia alee eee Secale EE AE COENA see EEES 7 1 System Time System Date 4 oco rne ripetuto eege ee 7 2 EE dl E 7 2 el E 7 13 Boot UE EE 7 14 4 P T 7 14 7 6 Appendix A BIOS Error Beep Codes Appendix B Installing Windows B 1 Installing the Windows OS for a RAID System seesesessss B 1 SUPERSERVER 1022G NTF User s Manual B 2 Installing the Windows OS for a Non RAID System Appendix C System Specifications Chapter 1 Introduction 1 1 Chapter 1 Introduction Overview The SuperServer 1022G NTF is a high end server comprised of two main subsystems the SC815TQ 563UBP 1U server chassis and the H8DGU F dual processor serverboard Please refer to our web site for information on operating systems that have been certified for use with the system www supermicro com In addition to the serverboard and chassis various hardware components have been included with the 1022G NTF as listed below One 1 mini SATA to USB adapter for slim DVD CDM USATA G O P One 1 Slim SATA DVD kit MCP 220 81502 0N One 1 slim DVD R
52. lect the time out for detecting ATA ATAPI devices The default value is 35 SUPERSERVER 1022G NTF User s Manual gt PCI PnP Configuration Clear NVRAM Select Yes to clear NVRAM during boot up The options are Yes and No Plug amp Play O S Select Yes to allow the OS to configure Plug amp Play devices This is not required for system boot if your system has an OS that supports Plug amp Play Select No to allow AMIBIOS to configure all devices in the system PCI Latency Timer This option sets the latency of all PCI devices on the PCI bus Select a value to set the PCI latency in PCI clock cycles Options are 32 64 96 128 160 192 224 and 248 ROM Scan Ordering This setting determines which kind of option ROM activates prior to another Options include Onboard First and Addon First SXB1 Slot SXB2 Slot These settings Enable or Disable the specified PCI slot in your system Onboard LAN Option ROM Select This setting allows you to select the onboard LAN option ROM for iSCSI or PXE Load Onboard LAN 1 Option ROM This option allows you to Enable or Disable the onboard LAN 1 option ROM Load Onboard LAN 2 Option ROM This option allows you to Enable or Disable the onboard LAN 2 option ROM Primary Video Controller This option specifies the primary video controller for Onboard VGA or Other Chapter 7 BIOS gt SuperlO Device Configuration Serial 1 Address This option specifies the base I O port
53. m Technical Support Web Site www supermicro com Europe Address Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 Email sales supermicro nl General Information support 2supermicro nl Technical Support rma supermicro nl Customer Support Asia Pacific Address Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C Tel 886 2 8226 3990 Fax 886 2 8226 3991 Web Site www supermicro com tw Technical Support Email support supermicro com tw Tel 886 2 8228 1366 ext 132 or 139 1 6 Chapter 2 Server Installation Chapter 2 Server Installation 2 1 Overview This chapter provides a quick setup checklist to get your SuperServer 1022G NTF up and running Following these steps in the order given should enable you to have the system operational within a minimum amount of time This quick setup assumes that your system has come to you with the processors and memory preinstalled If your system is not already fully integrated with a serverboard processors system memory etc please turn to the chapter or section noted in each step for details on installing specific components 2 2 Unpacking the System You should inspect the box the SuperServer 1022G NTF was shipped in and note if it was damaged in any way If the server itself shows damage you should file a damage claim with the carrier who
54. manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warn ing applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate WARNING Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other repro
55. most cases allow the system to continue the boot up process The error messages normally appear on the screen Fatal errors are those which will not allow the system to continue the boot up pro cedure If a fatal error occurs you should consult with your system manufacturer for possible repairs Beep Code 1 beep 1 long beep 8 beeps 1 continuous beep with the front panel OH LED on BIOS Error Beep Codes Error Message Description Refresh Circuits have been reset Ready to power up Memory error No memory detected in the system Display memory read Video adapter missing or with faulty write error memory System Overheat 1 continuous beep with the front panel OH LED on SUPERSERVER 1022G NTF User s Manual Notes Appendix B Installing Windows Appendix B Installing Windows After all hardware components have been installed you must first configure Intel South Bridge RAID Settings before you install the Windows OS and other software drivers To configure RAID settings please refer to RAID Configuration User Guides posted on our web site at www supermicro com support manuals B 1 il Installing the Windows OS for a RAID System Insert Microsoft s Windows XP 2003 2008 Vista Setup CD in the CD driver and the system will start booting up from CD Press the lt F6 gt key when the message Press F6 if you need to install a third party SCSI or RAID driver displays When the Windows OS Setu
56. nual H8DGU F Quick Reference Jumper Description JBT1 CMOS Clear JI2C1 JI2C2 JPG1 VGA Enable Disable JPL1 JWD Watch Dog LED LAN Ports Dedicated IPMI LAN LE1 DP2 Connector COM1 COM2 FAN 1 8 IPMB IPMI LAN JD1 JF1 JL1 JOH1 JPW1 JPW2 3 JWF1 LAN1 2 PS2 Mouse Keyboard SATAO SATA5 T SGPIO 1 TSGPIO 2 UID UIOP USBO 1 USB2 3 USB4 5 USB6 VGA I2C to PCI E Slot Enable Disable LAN 1 2 Enable Disable Default Setting See Section 2 7 Both Closed Enabled Pins 1 2 Enabled Pins 1 2 Enabled Pins 1 2 Reset Description LEDs for the LAN Ethernet ports LEDs for the dedicated IPMI LAN Ethernet port LED for UID Button LED for Serverboard Power On Description COM Serial Port Header Chassis CPU Fan Headers System Management Bus Header for the IPMI Slot Dedicated IPMI LAN Port H8DGU F only Speaker Header Front Panel Connector Chassis Intrusion Header Overheat Warning Header 24 pin Main ATX Power Connector 12V 8 pin CPU Power Connectors Compact Flash Card Power Connector Gigabit Ethernet RJ45 Ports PS2 Mouse Keyboard connectors SATA Ports Serial General Purpose Input Output Header for SATA Unit Identifier Button Universal I O Power Connector Universal Serial Bus USB Ports Headers and Type A Port VGA Connector Chapter 5 Advanced Serverboard Setup 5 8 Connector Definitions ATX Power 24 pin Connector Pin Definitions Powe
57. ocedures can be found in Chapter 6 The following is a general outline of the main features of both chassis System Power The SC815TQ 563UBP features a redundant 560W power supply consisting of two power modules The system does not need to be shut down when replacing or removing a single power supply module SATA Subsystem The SC815TQ 563UBP chassis was designed to support four hot swap SATA hard drives PCI Expansion Slots A riser card RSC R1UU UE16 optional on the right side of the chassis can support an AOC PG i2 add on card to provide two additional Gb LAN ports The left side supports a UIO card and one PCI E x16 card The system can support four SAS SATA drives with an optional UIO SAS card See our web site for details http www supermicro com products nfo UIO cfm See section 5 6 for further details Right and left refer to the side when viewed from the front of the system 1 3 SUPERSERVER 1022G NTF User s Manual Front Control Panel The chassis control panel provides you with system monitoring and control LEDs indicate system power HDD activity network activity two and UlD overheat fan fail power fail A main power button a system reset button and a UID button are also included UO Backplane The SC815TQ 563UBP is an extended ATX form factor chassis that is designed to be used in a 1U rackmount configuration Ports on the I O backplane include one COM port a VGA port two USB 2 0 ports PS 2 mou
58. or dual CPU configurations 5 3 SUPERSERVER 1022G NTF User s Manual Installing a Passive CPU Heatsi quired amount has already been applied nk Do not apply any thermal grease to the heatsink or the CPU die the re 2 Place the heatsink directly on top of the CPU so that the heat sink screws are aligned with the mounting holes on the back plate 3 Make sure the screwdriver torgue setting is no more than 5 0 Kgf cm 4 3 Ibf in and keep the heat sink direction vertical 4 until fully tightened Tighten each screw a few turns at a time while alternating between the two Figure 5 3 SNK 0042P Heatsink No 1 Screw No 2 Screw Removing the Heatsink Unscrew the heatsink screws from the mo N N A N Ki SSN Warning We do not recommend removing the CPU or the heatsink How ever if you do need to remove the heatsink please follow the instructions below to prevent damage to the CPU or other components therboard a few turns at a time alternating between the two until the screws can be removed 2 Gently wriggle the heatsink to loosen it from the CPU Do not use excessive force when wriggling the heatsink 3 Once the CPU is loose remove the it from the CPU socket 4 grease Reapply the proper amount of the re installing the CPU and the heatsink 5 4 Clean the surface of
59. orm only The current subnet address in the BMC is shown Gateway Address In the field provided here enter the Gateway address in the decimal form of XXX XXX XXX Xxx With xxx having a value of less than 256 and in decimal form only The current Gateway address in the BMC is shown MAC Address In the field provided here enter the MAC address in the hex form of xx xx XX XX XX XX with xx in hex form only The current MAC address in the BMC is shown BMC Watch Dog Timer Action This setting is used to set the Watch Dog function which allows the BMC to reset or powerdown the system if the OS crashes or hangs Options include Disabled Reset System Power Down and Power Cycle Chapter 7 BIOS gt Event Log Configuration View Event Log Pressing the Enter key will open the event log Use the Tt and 4 keys to navigate through the system event log Mark All Events as Read Selecting this and pressing the Enter key marks all events as read in the event log Clear Event Log Selecting this and pressing the Enter key clears the system event log SR56x0 RD890S PCIE Error Log This setting allows you set an error log ofr PCIE errors Options include Yes or No 7 4 Security Menu AMI BIOS provides a Supervisor and a User password If you use both passwords the Supervisor password must be set first Change Supervisor Password Select this option and press Enter to access the sub menu and then type in the password
60. p screen appears press S to specify additional device s Insert the driver diskette Intel AA RAID Windows XP 2003 2008 Vista Driver for ICH10R into the floppy drive and press the Enter key Choose the Intel R ICH10R SATA RAID Controller from the list indicated in the Windows OS Setup Screen and press the Enter key Press the Enter key to continue the installation process If you need to specify any additional devices to be installed do so at this time Once all devices are specified press the Enter key to continue with the installation From the Windows OS Setup screen press the Enter key The Windows OS Setup will automatically load all device files and then continue the Win dows OS installation After the Windows OS Installation is complete the system will automatically reboot B 1 SUPERSERVER 1022G NTF User s Manual B 2 Installing the Windows OS for a Non RAID System Insert Microsoft s Windows XP Windows 2003 Windows 2008 Windows Vista Setup CD in the CD drive and the system will start booting up from CD Continue with the OS installation The Windows OS Setup screen will display From the Windows OS Setup screen press the lt Enter gt key The Windows OS Setup will automatically load all device files and then continue with the OS installation After the Windows OS Installation is complete the system will automatically reboot Insert the Supermicro Setup CD that came with your
61. placed Contact technical support for details and support 4 2 General Safety Precautions A Follow these rules to ensure general safety Keep the area around the 1012G MTF clean and free of clutter e The 1022G NTF weighs approximately 43 Ibs 19 5 kg when fully loaded When lifting the system two people at either end should lift slowly with their feet spread out to distribute the weight Always keep your back straight and lift with your legs Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won t accidentally be stepped on 4 2 Chapter 4 System Safety While working on the system do not wear loose clothing such as neckties 4 3 and unbuttoned shirt sleeves which can come into contact with electrical circuits or be pulled into a cooling fan Remove any jewelry or metal objects from your body which are excellent metal conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present After accessing the inside of the system close the system back up and secure it to the rack unit with the retention screws after ensuring that all con nections have been made ESD Precautions A Electrostatic discharge ESD is generated by two objects with different electrical charges coming into contact with each other An electrical discharge is created to neutralize
62. pment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale C 4
63. r Connectors Pin Definition Pin Definition 13 3 3V 1 3 3V A24 pin main power supply connector JPW1 FAET PERS my and three 8 pin CPU PWR connectors ES STE JPW2 JPW3 JPW4 on the motherboard ppm F mm These power connectors meet the SSI EPS de x 17 COM 5 COM 12V specification In addition to the 24 pin 18 COM 6 5V ATX power connector the 12V 8 pin CPU PWR connectors at UPW2 JPW3 JPW4 must LU SON 7 COM 20 Res NC 8 PWR_OK also be connected to your power supply See the table on the right for pin definitions p noy UM Ee 22 45V 10 12V Warning To prevent damage to the power SSES eeler supply or motherboard please use a power a Leem ee aaay supply that contains a 24 pin and three 8 pin power connectors Be sure to connect these 12V 8 pin PWR Connector connectors to the 24 pin JPW1 and the Pin Demians three 8 pin JPW2 JPW3 and JPW4 power Ss en h4 connectors on the motherboard Failure in BUE Gouna n h 12V doing so will void the manufacturer warranty 9 torougn amp M on your power supply and motherboard ERC PW ON Connector Power Button Pin Definitions The PW ON connector is on pins 1 and 2 of JF1 JF1 This header should be connected to the Pin Definition chassis power button See the table on the T ewon right for pin definitions 2 Ground Reset Connector Reset Button Pin Definitions The reset connector is located on pins 3 and JF1 4 of JF1 and attaches
64. r System Date using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt key or the lt Arrow gt keys to move between fields The date must be entered in DAY MM DD YYYY format The time is entered in HH MM SS format Please note that time is in a 24 hour format For example 5 30 A M appears as 05 30 00 and 5 30 P M as 17 30 00 7 3 Advanced Settings Menu gt Boot Feature Quick Boot If Enabled this option will skip certain tests during POST to reduce the time needed for the system to boot up The options are Enabled and Disabled Quiet Boot If Disabled normal POST messages will be displayed on boot up If Enabled this display the OEM logo instead of POST messages Add On ROM Display Mode This option sets the display mode for Option ROM The options are Force BIOS or Keep Current Bootup Num Lock This option selects the power on state for the NUM lock to either On or Off PS 2 Mouse Support Use this option to select support for the PS 2 mouse Options are Disabled Enabled or Auto Wait for F1 if Error This setting controls the system response when an error is detected during the boot sequence When enabled BIOS will stop the boot sequence when an error is detected at which point you will need to press the F1 button to re enter the BIOS setup menu The options are Enabled and Disabled Hit DEL Message Display Use this option to Enable or Disable the Press DEL to run setup message in
65. rmation CPU Temperature CPU1 Temperature CPU2 Temperature NB Temperature VRD1 Temperature VRD2 Temperature System Temperature Air Tempera ture Fan 1 8 Reading CPU1 VCore CPU2 VCore CPU1 Mem VTT CPU2 Mem VTT CPU1 Mem CPU2 Men 1 1V 1 8V 5V 12V 12V 3 3 Vcc 3 3 VSB VBAT and HT Voltage Chapter 7 BIOS gt ACPI Configuration PS2 KB MS Wakeup This setting allows you to Enable or Disable PS2 keyboard and mouse wakeup ACPI Aware O S This setting Enables or Disables ACPI support for the system s operating system Options include Yes enabled or No disabled ACPI APIC Support Determines whether to include the ACPI APIC table pointer in the RSDT pointer list The available options are Enabled and Disabled Headless Mode Use this setting to Enable or Disable headless operation mode through ACPI ACPI Version Features Use this setting the determine which ACPI version to use Options are ACPI v1 0 ACPI v2 0 and ACPI v3 0 gt IPMI Configuration This menu shows static information about the IPMI firmware revision and status of the BMC as well as options for IPMI configuration gt View BMC System Event Log Pressing the Enter key will open the following settings Use the and keys to navigate through the system event log Clear BMC System Event Log Selecting this and pressing the Enter key will clear the BMC system event log gt Set LAN Configuration Use the and keys to choo
66. rol Eeer ege 5 5 Bu MO POMS esu o EE M MM SUE rere 5 6 5 0 Installing MeMO cr B 5 7 Memory SUPPO HERREN eet et 5 7 DIMM Module Population Configuration ke 5 8 vii SUPERSERVER 1022G NTF User s Manual 56 Adding PI NS mr 5 10 PCI Eet 5 10 5 7 Serverboard Details cccccccecceeceeeeececeeeeeeeeeeneaeeeeeeeeeseeeaeeeeeeeeesessnsneaeeeees 5 11 H8DGU F Quick Reference Me 5 12 5 8 Connector Definitions rosiers aeaee a eE EEE E REEE EENE 5 13 Power Connectors ccccecccccceceeeeeceeeeeeceeeeeceeceeaeeeeeeeeesncneaeeeeeeeeeeseeeaees 5 13 PAN ON GODnDDnGGIOF eet te NE e Exeter dece Dev aaan aas 5 13 Reset ere glar Te o 5 13 Overheat Fan ESIEEDAQDLDD dai atcdicecuendo cuidas cic atn nts dasea r tae etcen ect 5 14 NIC2 LANZ LE D ME c 5 14 NICI LAN ER E 5 14 miD BAE D E A A E A E AEE A AEE E 5 14 Power Ee 5 14 BINA ES PR aoro p IDE ps osama E 5 14 Universal Serial Bus Porte 5 15 USB EE 5 15 Fani Headers rt en nr trn n HE na ects Fa ERE EEE PE EYRR Ere TEE ois 5 15 Serial Porte 5 15 jte c PLU 5 16 UIO Power GCOhneCIOr ieiie rine tke ket eae a E ESE EAR 5 16 LAN1 2 Ethernet Porte 5 16 EE EL Te EE 5 17 Overheat LED es rae eoa E ae a Eaa a e a AE EEAS aas 5 17 e 5 17 ATX PS 2 Keyboard and PS 2 Mouse Porte ek 5 17 Unit Identifier Button ME 5 18 Eege 5 18 Video Connecti senere epee EE eE aa e EE aA AEA Cae evataSeatey deste eee 5
67. s Cathode 7 Pin3 NA speaker you should close pins 6 7 with a jumper Connect a cable to pins 4 7 of JD1 Speaker Connector to use an external speaker Pin Definitions Pin Setting Definition Pins 4 7 External Speaker Pins 6 7 Internal Speaker ATX PS 2 Keyboard and PS 2 Mouse PS 2 Keyboard Mouse Pin Ports Definitions The ATX PS 2 keyboard and PS 2 mouse are PS Keyboard Pos Mouse located next to the Back Panel USB Ports Pin Definition Pin Deinen 0 3 on the motherboard See the table at KB Data 1 Mouse Data right for pin definitions a New 2 ke Connection Connection 3 Ground 3 Ground 4 Mouse KB 4 Mouse KB VCC 5V VCC 5V 5 KB Clock 5 Mouse Clock 6 No Connec 6 No Connec tion tion VCC with 1 5A PTC current limit SUPERSERVER 1022G NTF User s Manual Unit Identifier Button In addition to the UID Unit Identifier button Piin Definitions on the rear I O panel there is another UID pie Definition button located on the control panel When you push either UID button both Rear UID and Front Panel UID Indicators will illumi nate Push either button again to turn off both indicators These UID indicators provide easy identification of a system unit that may be in need of service 2 Ground Button In IPMB IPMB A System Management Bus header for the Pin Definitions IPMI slot is located at IPMB Connect the Lee eon i appropriate cable here to use the IPMB
68. s the drive is rebuilding When solid it indicates a drive failure If a hard drive fails you should be notified by your system management software Please refer to Chapter 6 for instructions on replacing failed hard drives 3 4 Chapter 4 System Safety 4 1 Chapter 4 System Safety Electrical Safety Precautions A Basic electrical safety precautions should be followed to protect yourself from harm and the SuperServer 1022G NTF from damage Be aware of the locations of the power on off switch on the chassis as well as the room s emergency power off switch disconnection switch or electrical outlet If an electrical accident occurs you can then quickly remove power from the system Do not work alone when working with high voltage components Power should always be disconnected from the system when removing or in stalling main system components such as the serverboard memory modules and floppy drive When disconnecting power you should first power down the operating system first and then unplug the power cords The unit has more than one power supply cord Disconnect two power supply cords before servicing to avoid electrical shock When working around exposed electrical circuits another person who is familiar with the power off controls should be nearby to switch off the power if neces sary Use only one hand when working with powered on electrical equipment This is to avoid making a complete circuit which will c
69. s to use Options are 115200 8 n 1 57600 8 n 1 38400 8 n 1 19200 8 n 1 and 09600 8 n 1 Flow Control Selects the flow control to be used for console redirection Options are None Hardware and Software 7 9 SUPERSERVER 1022G NTF User s Manual Redirection After BIOS POST Options are Disable no redirection after BIOS POST Boot Loader redirection during POST and during boot loader and Always redirection always active Note that some OS s may not work with this set to Always Terminal Type Selects the type of the target terminal Options are ANSI VT100 and VT UTF8 VT UTF8 Combo Key Support Allows you to Enable or Disable VT UTF8 combination key support for ANSI VT100 terminals Sredir Memory Display Delay Use this setting to set the delay in seconds to display memory information Options are No Delay 1 sec 2 secs and 4 secs gt Hardware Health Configuration CPU Overheat Alarm This setting allows you to specify the type of alarm for CPU overheating Options include The Early Alarm and The Default Alarm Fan Speed Control This feature allows the user to determine how the system will control the speed of the onboard fans The options are Full Speed FS Max Cooling Performance PF Better Cooling Balanced BL Balance between performance and energy saving Energy Saving ES Lower Power and Noise Other items in the submenu are systems monitor displays for the following info
70. se and keyboard ports and two gigabit Ethernet ports A UID Unit Identifier button and LED are also located beside the LAN2 Ethernet port Cooling System The SC815TQ 563UBP chassis has an innovative cooling design that features four sets of 4 cm counter rotating fans located in the middle section of the chassis There is a Fan Speed Control Mode setting in BIOS that allows chassis fan speed to be determined by system temperature The power supply module also includes a cooling fan 1 4 Chapter 1 Introduction Figure 1 1 AMD SR5670 SP5100 Chipset System Block Diagram Note This is a general block diagram Please see Chapter 5 for details DIMM A in Foma KX 848 3 2GT s DI CE fame AMO us AMD CREER DIMM BO DIMM B1 Socket G34 DIMM BO DIMM CT Socket G34 K gt Lowi co ons Cu Kae C a DIMM DO HT3 Link 16x16 5 2GT s HT3 Link 8 8 x 8 8 6 4GT s KAWELA SR5670 D idi GE ES PCI E GEN x8 in x4 DDR2 SDRAM Sue M PSU 12C VGA SMBus SP5100 SATA x6 mee CE ie WPCMASOR pe Jr COM T RJ45 E INTEL PCI E GEN2 x16 K POLEGENZX4 SIO HWM we3527 ISB MS W83795G FE PHY 7xUSB 1 5 SUPERSERVER 1022G NTF User s Manual 1 4 Contacting Supermicro Headquarters Address Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A Tel 1 408 503 8000 Fax 1 408 503 8008 Email marketing supermicro com General Information support supermicro co
71. se the desired channel number This displays Channel Number and Channel Number Status information This menu contains options for inputing settings for the SET LAN Configuration Command See IPMI 1 5 Specification table 11 1 for details Use the and keys to choose the desired channel number Note Each question in this group may take a considerable amount of time 75 SUPERSERVER 1022G NTF User s Manual IP Address Source Select the source of this machine s IP address If Static is selected you will need to know and enter manually the IP address of this machine below If DHCP is selected the BIOS will search for a DHCP Dynamic Host Configu ration Protocol server in the network it is attached to and request the next available IP address The options are DHCP and Static The following items are assigned IP addresses automatically if DHCP is selected under IP Address Source above IP Address This submenu sets the IP address source as either Static or DHCP Selecting Static allows you to manually set the IP Address Subnet Mask and Gateway Address In the field provided here enter the IP address in the decimal form of xxx xxx XXX XXX With xxx having a value of less than 256 and in decimal form only The IP address and current IP address in the BMC are shown Subnet Mask In the field provided here enter the Subnet address in the decimal form of XXX XXX XXX XXX With xxx having a value of less than 256 and in decimal f
72. serverboard into the CD drive during system boot and the main screen will display B 2 Appendix C System Specifications Appendix C System Specifications Processors Dual AMD Opteron 6100 series Socket G34 type processors Note You must install at least two processors for full functions to be supported Note Please refer to our web site for a complete listing of supported processors Chipset One AMD SR5670 chipset and one SP5100 Southbridge chipset BIOS 16 Mb AMIBIOS SPI Flash ROM Memory Capacity Sixteen single dual tri quad channel DIMM slots supporting up to 256GB of DDR3 1333 1066 800MHz registered ECC SDRAM or 64 GB of DDR3 1333 1066 800 MHz unbuffered ECC non ECC SDRAM Note See the memory section in Chapter 5 for details SATA Controller AMD SP5100 on chip controller for six port Serial ATA RAID 0 1 and 10 supported Drive Bays Four 4 hot swap drive bays to house four 4 SATA drives Peripheral Drive Bays One 1 slim DVD ROM drive Expansion Slots Right side optional 2x Gb LAN ports w RSC R1UU E8PR riser card and AOC PG i2 add on card Left side one UIO card and one PCI Express x16 slot C 1 SUPERSERVER 1022G NTF User s Manual Serverboard H8DGU F Proprietary form factor Dimensions 12 28 x 13 05 312 x 331 mm Chassis SC815TQ 563UBP Form Factor 1U rackmount Dimensions WxHxD 17 x 1 7 x 25 6 in 432 x 43 x 650 mm Weight Gross Bare Bone 43 lbs 19 5 k
73. sink See Chapter 5 for instructions on processor and heatsink installation Your server system may have come with system memory already installed Make sure all DIMMs are fully seated in their slots For details on adding system memory refer to Chapter 5 If desired you can install add on cards to the system See Chapter 5 for details on installing PCI add on cards Make sure all power and data cables are properly connected and not blocking the chassis airflow See Chapter 5 for details on cable connections 2 8 Chapter 2 Server Installation Figure 2 5 Accessing the Inside of the System 2 6 Checking the Drive Bay Setup Next you should check to make sure the peripheral drives and the SATA drives and SATA backplane have been properly installed and all connections have been made Checking the Drives 1 All drives are accessable from the front of the server The SATA disk drives can be installed and removed from the front of the chassis without removing the top chassis cover 2 Aslim DVD ROM drive should be preinstalled in your server For servicing the DVD ROM drive you will need to remove the top chassis cover Refer to Chapter 6 if you need to reinstall a DVD ROM drive to the system 3 Depending upon your system s configuration your system may have one or more drives already installed If you need to install SATA drives please refer to Chapter 6 2 9 SUPERSERVER 1022G NTF User s Manual Checking the A
74. stall components and perform maintenance on the 815TS 563UBP chassis For component installation follow the steps in the order given to eliminate the most common problems encountered If some steps are unnecessary skip ahead to the next step Tools Required The only tool you will need to install components and perform maintenance is a Philips screwdriver 6 1 Static Sensitive Devices Electrostatic discharge ESD can damage electronic components To prevent damage to any printed circuit boards PCBs it is important to handle them very carefully The following measures are generally sufficient to protect your equipment from ESD damage Precautions Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing any board from its antistatic bag e Handle a board by its edges only do not touch its components peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins e Put the serverboard add on cards and peripherals back into their antistatic bags when not in use For grounding purposes make sure your computer chassis provides excellent conductivity between the power supply the case the mounting fasteners and the serverboard 6 1 SUPERSERVER 1022G NTF User s Manual Figure 6 1 Chassis Front and Rear Views Slim DVD ROM Drive System LEDs Control Panel U Ans o6000 90 o
75. t Manufuacturer Supplied Hardware Support Disk and hit the lt En ter gt key 5 25 SUPERSERVER 1022G NTF User s Manual 5 Highlight the first Adaptec RAID driver shown and press the lt Enter gt key to install it 6 Press lt Enter gt again to continue with the Windows setup 5 13 Installing Drivers The CD that came bundled with the system contains drivers some of which must be installed such as the chipset driver After inserting this CD into your CD ROM drive the display shown in Figure 5 7 should appear If this display does not appear click on the My Computer icon and then on the icon representing your CD ROM drive Finally double click on the S Setup icon Click the icons showing a hand writing on paper to view the readme files for each item Click the computer icons to the right of these items to install each item from top to the bottom one at a time After installing each item you should reboot the system before moving on to the next item on the list The bottom icon with a CD on it allows you to view the entire contents of the CD Figure 5 7 Driver Tool Installation Display Screen amp SUPERMICRO H8DGU Motherboard Drivers and Tools WinXP B ATI Catalyst Install Manager SUPERMICR Matrox G200e Graphics Driver Drivers amp Tools SR5670 Chipset H8DGU Intel PRO Network Connections Drivers SUPERMICRO Supero Doctor III Build driver diskettes and manuals Browse CD Auto Start Up Ne
76. t the CMOS pads with a metal object such as a small screwdriver 3 Remove the screwdriver or shorting device 4 Reconnect the power cord s and power on the system Note Do not use the PW_ON connector to clear CMOS 5 19 SUPERSERVER 1022G NTF User s Manual 12C to PCI Express Slot Jl C1 JI C2 allows you to enable the 1 C bus to communicate with the PCI Express slot For the jumpers to work properly please set both jumpers to the same setting If enabled both jumpers must be enabled If disabled both jumpers must be disabled See the table on the right for jumper settings Watch Dog Enable Disable JWD enables the Watch Dog function a system monitor that takes action when a software application freezes the system Jumping pins 1 2 will have WD reboot the system if a program freezes Jumping pins 2 3 will generate a non maskable interrupt for the program that has frozen See the table on the right for jumper settings Watch Dog must also be enabled in BIOS LAN1 2 Enable Disable Change the setting of jumper JPL1 to enable to enable or disable the LAN1 and LAN2 Ethernets ports See the table on the right for jumper settings The default setting is enabled VGA Enable Disable JPG1 allows you to enable or disable the VGA port The default position is on pins 1 and 2 to enable VGA See the table on the right for jumper settings 5 20 I2C to PCI Express Slot Jumper Settings JI2C1 JI2C2 Jumper Set
77. the IDE disk drive support cannot be determined Select 0 to allow BIOS to use PIO mode 0 which has a data transfer rate of 3 3 MBs Select 1 to allow BIOS to use PIO mode 1 which has a data transfer rate of 5 2 MBs Select 2 to allow BIOS to use PIO mode 2 which has a data transfer rate of 8 3 MBs Select 3 to allow BIOS to use PIO mode 3 which has a data transfer rate of 11 1 MBs Select 4 to allow BIOS to use PIO mode 4 which has a data transfer rate of 16 6 MBs This setting generally works with all hard disk drives manufactured after 1999 For other disk drives such as IDE CD ROM drives check the specifications of the drive DMA Mode Selects the DMA Mode Options are Auto SWDMAO SWDMA1 SWDMA2 MWDMAO MDWDMA1 MWDMA2 UDMAO UDMA1 UDMA2 UDMA3 UDMA4 and UDMAS5 SWDMA Single Word DMA MWDMA Multi Word DMA UDMA UltraDMA S M A R T Self Monitoring Analysis and Reporting Technology SMART can help predict impending drive failures Select Auto to allow BIOS to auto detect hard disk drive support Select Disabled to prevent AMI BIOS from using the S M A R T Select Enabled to allow AMI BIOS to use the S M A R T to sup port hard drive disk The options are Disabled Enabled and Auto 32 Bit Data Transfer Select Enabled to activate the function of 32 Bit data transfer Select Dis abled to deactivate the function The options are Enabled and Disabled IDE Detect Timeout Sec Use the keys to adjust and se
78. this difference which can damage electronic components and printed circuit boards The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD Use a grounded wrist strap designed to prevent static discharge Keep all components and printed circuit boards PCBs in their antistatic bags until ready for use Touch a grounded metal object before removing the board from the antistatic bag Do not let components or PCBs come into contact with your clothing which may retain a charge even if you are wearing a wrist strap Handle a board by its edges only do not touch its components peripheral chips memory modules or contacts When handling chips or modules avoid touching their pins Put the serverboard and peripherals back into their antistatic bags when not in use 4 3 SUPERSERVER 1022G NTF User s Manual For grounding purposes make sure your computer chassis provides excellent conductivity between the power supply the case the mounting fasteners and the serverboard 4 4 Operating Precautions A Care must be taken to assure that the chassis cover is in place when the 1022G NTF is operating to assure proper cooling Out of warranty damage to the system can occur if this practice is not strictly followed Figure 4 1 Installing the Onboard Battery m C LITHIUM BATTERY S SS BATTERY HOLDER KR Du H way a damaged b
79. ting Definition Closed Enabled Open Disabled Watch Dog Jumper Settings JWD Jumper Setting Definition Pins 1 2 Reset Pins 2 3 NMI Open Disabled Note When Watch Dog is enabled the user must write their own appli cation software to disable the Watch Dog Timer LAN1 2 En Disable Jumper Settings JPL1 Jumper Setting Definition Pins 1 2 Enabled Pins 2 3 Disabled VGA Enable Disable Jumper Settings JPG1 Jumper Setting Definition Pins 1 2 Enabled Pins 2 3 Disabled Chapter 5 Advanced Serverboard Setup 5 10 Onboard Indicators LAN LED Connection Speed Indica tor ED Color Definition LAN1 LAN2 LEDs L The Ethernet ports located beside the VGA Off 10 MHz port have two LEDs On each Gb LAN port Ge 100 MHz one LED blinks to indicate activity while the other may be green amber or off to indicate the speed of the connection See the table on the right for the functions associated with the connection speed LED Dedicated IPMI LAN LEDs IPMI LAN Link LED Left amp A dedicated IPM LAN is also included on GE E the H8DGU F serverboard DP5001 The E Se SES SC Link Green 100 Mb s amber LED on the right indicates activity Left fm Ee while the green LED on the left indicates Activity the speed of the connection See the table Righi eee at right for more information UID LED LE1 A rear UID LED Indicator
80. to the reset switch on the computer chassis See the table on the right for pin definitions Pin Definition 3 Reset 4 Ground SUPERSERVER 1022G NTF User s Manual Overheat Fan Fail LED OH OH Fan Fail LED Pin Definitions OH Fan Fail Connect an LED to the OH connection on JF1 LED Status pins 7 and 8 of JF1 to provide advanced warning of chassis overheating or fan failure SES cc P ae Solid Overheat Refer to the table on the right for pin defini See ss 8 Control Blinking Fan fail tions and status indicators NIC2 LAN2 LED NIC2 LED Pin Definitions JF1 Pin Definition Pin Definition State Indication The LED connections for LAN2 are on pins 9 and 10 of JF1 Attach LAN LED cables to display network activity See the table on the i a B Vcc right for pin definitions 10 Ground NIC1 LAN1 LED NIC1 LED Pin Definitions JF1 Pin Definition The LED connections for LAN1 are on pins 11 and 12 of JF1 Attach LAN LED cables to display network activity See the table on the a 11 Vcc right for pin definitions 12 Ground Pin Definitions The HDD LED connection is located on pins JF1 13 and 14 of JF1 Attach the hard drive LED cable here to display disk activity for any 13 Vec hard drives on the system including SAS 14 HD Active Serial ATA and IDE See the table on the right for pin definitions Power On LED Power LED
81. upermicro s UIO Universal I O technology UIO serverboards have a PCI Express x8 slot that can support any one of several types of UIO card types to add SAS ports additional LAN ports etc to the serverboard This allows the user to tailor the serverboard to their own needs Note the server does not come with a UIO card installed Serial ATA An on chip SP5100 SATA controller is integrated into the H8DGU F to provide a six port 3 Gb sec SATA subsystem which is RAID 0 1 and 10 supported The SATA drives are hot swappable units Note You must have RAID set up to enable the hot swap capability of the SATA drives Documentation on RAID setup guidelines can be found on our web site Onboard Controllers Ports The color coded I O ports include two COM ports one header and one port a VGA monitor port Seven USB 2 0 ports 2x rear 4x header 1x type A PS 2 mouse and keyboard ports two gigabit Ethernet ports and one dedicated IPMI LAN port 1 2 Chapter 1 Introduction Graphics Controller The H8DGU F features an integrated Matrox G200eW graphics chip which includes 16 MB of DDR2 memory Other Features Other onboard features that promote system health include onboard voltage monitors auto switching voltage regulators chassis and CPU overheat sensors virus protection and BIOS rescue 1 3 Server Chassis Features The 1022G NTF is built upon the SC815TQ 563UBP chassis Details on the chassis and on servicing pr
82. xt Time For more information please visit SUPERMICRO s web site SUPERMICRO Computer Inc 5 26 Chapter 5 Advanced Serverboard Setup Supero Doctor Ill The Supero Doctor III program is a Web base management tool that supports remote management capability It includes Remote and Local Management tools The local management is called SD III Client The Supero Doctor III program included on the CD ROM that came with your motherboard allows you to monitor the environment and operations of your system Supero Doctor III displays crucial system information such as CPU temperature system voltages and fan status See the Figure below for a display of the Supero Doctor Ill interface Note The default User Name and Password for SuperDoctor III is ADMIN AD MIN Note When SuperDoctor III is first installed it adopts the temperature threshold settings that have been set in BIOS Any subsequent changes to these thresholds must be made within Super Doctor as the Super Doctor settings override the BIOS settings To set the BIOS temperature threshold settings again you would first need to uninstall SuperDoctor III Figure 5 8 Supero Doctor Ill Interface Display Screen Health Information T Supero Doctor IHI Microsoft Internet Explorer NIS lal x File Edit View Favorites Tools Help E Sou Wee ESuper Doctor TIME cmm Remote Management EAT System Info Health Info Performance Remote Control Configuration Adm
83. you replace the failed hot swap module Replace with the same model which can be ordered directly from Supermicro see Contact Information in the Preface T First unplug the power cord from the failed power supply module To remove the failed power module push the release tab on the back of the power supply to the side and then pull the module straight out see Figure 6 6 The power supply wiring was designed to detach automatically when the module is pulled from the chassis Replace the failed power module with another PWS 651 1R power supply module Simply push the new power supply module into the power bay until you hear a click Finish by plugging the AC power cord back into the module Figure 6 6 Removing Replacing the Power Supply 6 8 Chapter 7 BIOS Chapter 7 BIOS 7 1 Introduction This chapter describes the AMI BIOS Setup Utility for the SuperServer 1022G NTF The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens Starting the Setup Utility To enter the BIOS Setup Utility hit the lt Delete gt key while the system is booting up In most cases the lt Delete gt key is used to invoke the BIOS setup screen There are a few cases when other keys are used such as lt F1 gt lt F2 gt etc Each main BIOS menu option is described in this manual The Main BIOS screen has two main frames

Supermicro AS-1022G-NTF

Contents

Download Pdf Manuals

Related Search

Related Contents