Baumatic OMBRA4SS dishwasher
Contents
1. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necessary repair If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then he will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by Baumatic Ltd has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance IMPORTANT Baumatic Ltd operates a policy of continuous improvement and reserves the right to adjust and modify its products without prior notification 34 General troubleshooting Start up problems The appliance does The socket does not work not start The appliance is not properly connected The dishwasher is not properly closed The water tap is closed There is no water supply to the property Insufficient water system pressure Inlet hose is kinked or crushed Filter for outlet hose or solenoid valve is blocked All necessary operations to start the di2. Main filter 2 Coarse filter 3 Fine filter Main filter Food and soil particles are trapped by this filter and pulverised by a special jet on the lower spray arm This debris is then washed down the drain Coarse filter Larger items such as pieces of bone or glass which could clog the drain are trapped in this filter Fine filter This filter holds soil and food residue in the sump area and prevents it from being redeposited on the dishes during a wash cycle IMPORTANT Whilst the filtering system is efficient your dishwasher is not a waste disposal unit All items being washed inside of the dishwasher should have food scraps removed from them before being loaded into the appliance 28 Cleaning the filters For best performance and results the entire filter assembly should be thoroughly cleaned regularly ideally after each wash cycle o Remove the basket from the appliance as described on pages 26 27 o Identify the coarse filter which is located in the middle of the main filter o Turn the coarse filter anti clockwise and then lift it upwards Rinse out this section under a tap to remove any food debris that remains in it o Pull out the main filter and rinse this under the tap to remove any food debris that is trapped in it o Pull out the fine filter and rinse this under the tap to remove any food debris that is trapped in it o Place the fine filter back in its original position o Place th
3. P2 709C Intensive P3 659C Normal P4 409C Rapid 70 Powerful Normal is the testing program for EN 50242 Program details Description 70 C wash 65 C wash 409C wash 70 C wash Intermediate Intermediate Intermediate Intermediate rinse x 2 rinse rinse rinse 70 C rinse 70 C rinse 70 C rinse 70 C rinse Drying Drying Drying Drying option Type of Mixed Mixed Mixed Mixed Mixed dishes resistance delicate resistance resistance dishes dishes dishes dishes Types of Normal Heavy Heavy soiling Light soiling Heavy soiling soiling soiling soiling not not for or using a for delicate delicate dishwasher items items cleaner 20 Opening and closing the door o Lightly press the upper middle part of the glass panel and the glass will detach from the stainless steel frame at the top o Pull the glass door forward to its limit and then continue to pull forward until the drawer comes out of the appliance o IMPORTANT The door should only be opened when the door locked icon N is not lit If the door is opened mid cycle then water may spill out of the machine which may cause damage to property and or injury to person o To close the door use the internal handle to slide the drawer back into place o IMPORTANT DO NOT close the door of the dishwasher without using the internal handle Otherwise there is a risk of trapping your fingers o Slide the drawer back fully into position and then pr
4. Dishes are coming into contact with the door gasket 35 Poor wash results Residue remains on The dishes were not properly arranged or there are dishes too many of them Some of the dishes are touching one another The spray arm cannot turn because of a large plate or saucepan being placed in the dishwasher Insufficient detergent is being used he detergent is old or has hardened The detergent being used is not appropriate The wash program selected is not suitable The spray arm is blocked by some food residue and should be cleaned The filters in the base of the appliance are dirty and or filled with residue The filters in the base are not positioned correctly The drain pump has jammed The water softener lid is not fully tightened The end of the drain hose is immersed in water Some plastic items are Insufficient detergent use detergent without faded chlorine Traces of a white coating Insufficient detergent on dishes and glasses Incorrect amount of rinse aid which ts difficult to Inappropriate salt was used remove The water softener lid is not fully tightened No salt has been added to the water softener or the water softener level has not been appropriately adjusted The dishes are not suitable for being washed in a dishwasher The dishes are not dried The dishes were removed from the appliance before they had sufficient time to dry The dishes were left in
5. appliance needs rinse aid or salt adding to it o The neon indicates that you need to add rinse aid to the appliance You should follow the procedure outlined on pages 13 14 o The S neon indicates that you need to add dishwasher salt to the appliance You should follow the procedure outlined on pages 11 12 Cleaning and maintenance IMPORTANT The appliance should be disconnected from your mains supply before commencing any cleaning process Removing the basket o Fully open the door of the dishwasher o Grasp the basket with both hands and then lift it upwards to detach it from the front part of the door o Push it towards the inside of the machine and with the basket still slightly raised remove it from inside of the dishwasher o IMPORTANT When removing the basket make sure that the upper part of the basket does hit against the inside of the cabinet or hook onto the door seal 26 o When placing the basket back inside of the dishwasher insert the basket wheels into the basket wheel guides o Slide the basket fully into the dishwasher and then refasten the basket to the support on the inside of the door as shown in the picture opposite o Check that the spray arm can turn fully before setting the dishwasher on a wash cycle 24 The filter system Your appliance is fitted with three levels of filtering these are located in the base of the dishwasher for ease of access 1
6. going to be used for a prolonged period of time then we would recommend that you do the following Fill the rinse aid dispenser Run one or two cycles with the dishwasher empty Disconnect the electrical and water connections Leave the door ajar slightly to prevent an unpleasant odour from developing o Clean all of the filters and dry the inside of the machine thoroughly 0 O O O Reconnecting the appliance after a period of disuse If the appliance has not been used for a prolonged period of time then before using the appliance again we would recommend that you do the following o Check that no sludge or rust has built up in the pipes If this has happened let water run through the tap for a few minutes o Reconnect the inlet hose and outlet hose making sure that the water tap is open o Reconnect the appliance to your mains supply 22 Error code failure system If your appliance senses that it is not operating correctly then an error code may appear on the LED display and or the warning icon I may light The following error codes can possibly be remedied by the customer and the steps outlined below should be followed BEFORE COMPLETING ANY MAINTAINEANCE ON THE APPLIANCE IT SHOULD BE DISCONNECTED FROM YOUR MAINS POWER SUPPLY EO o Insufficient amount of water in the dishwasher v Check that the water tap is fully open v Check that the filter in the inlet hose is not clogged Y Check that the inlet
7. hose is not kinked or crushed E1 o No water v Check that the water tap is fully open v Check that the filter in the inlet hose is not clogged Y Check that the inlet hose is not kinked or crushed E2 o The dishwasher does not drain v Check that the drain hose is not kinked or crushed v Check that the drain hose is not blocked Y Check that the filter system inside the dishwasher is not blocked o The machine was not able to fill with water v Check that the drain hose is not kinked or crushed Y Check that the drain hose is not blocked Y Check that the filter system inside the dishwasher is not blocked v Insufficient water pressure EC o Insufficient amount of water in the dishwasher v Check that no bowls have overturned inside the dishwasher Ed o The door is not locked correctly Y Check that the door is closed v Open and close the door After taking the necessary action to clear the fault code you should switch the machine off using the ON OFF key A Wait for a few seconds before switching the machine back on again 33 IMPORTANT If any other fault code appears on the LED display or the same fault code reoccurs you should not attempt to clear it yourself and contact the Baumatic Customer Care Department IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact Baumatic Customer Care on telephone number 0118 933 6911
8. of a wash cycle O When the wash cycle has completed the LCD display will show 0 and an audible signal will sound The 0 will disappear from the LCD display after 10 minutes but the audible signal will repeat every 10 minutes until the dishwasher is switched off IMPORTANT The door should only be opened when the door locked icon N is not lit The door locked icon will remain on for approximately 2 minutes after the wash cycle has completed When the door locked icon has gone out use the ON OFF key A to switch the dishwasher off IMPORTANT You should leave the appliance for 15 minutes BEFORE opening the door This will allow the steam generated from the final rinse s to dry the dishes Carefully open the door of the appliance as described on page 21 and leave it ajar for a few minutes to allow any remaining steam to disperse WARNING Hot steam may escape when the door is first opened so care should be taken Unload the dishwasher you should take care in case any of the items are still warm IMPORTANT If you leave the door of the dishwasher shut and do not unload the dishwasher for a prolonged period of time then you may get water droplets reforming on the washload 23 Additional rinse option If you are washing dishes that are very heavily soiled then it is possible to program the dishwasher so that it gives an additional rinse during the wash program o After you have selected a wash cycle as
9. of the Environment o Building Standards issued by the Scottish Development Department o IEE Wiring Regulations o Electricity At Work Regulations Before connecting the appliance make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage WARNING THIS APPLIANCE MUST BE EARTHED INSTALLATION OF THIS APPLIANCE PARTICULARLY WHEN LIFTING THE OVEN INTO THE HOUSING UNIT WE RECOMMEND THAT TWO PEOPLE COMPLETE THE IMPORTANT THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL YOU SHOULD DISPOSE OF ALL PACKAGING IN AN ENVIRONMENTALLY FRIENDLY MANNER 37 Installing the dishwasher into a kitchen cabinet o Ensure that the aperture that you will be fitting the dishwasher into is of the size given in the diagram above o Ensure that the rear panel of the furniture housing unit has been removed and that the ventilation cut out shown is adhered to o You must ensure that there is a hole to feed the electrical cable through There must also be holes left to connect the appliance to your mains water supply and to your drain outlet These steps must be done before commencing the rest of the installation process o IMPORTANT The stop valve for your water supply MUST be easily accessible during an emergency o Before proceeding with the rest of the installation you must connect the inlet h
10. placed with their bases upwards o Deep saucepans should be slanted to allow water to run off IMPORTANT Care should be taken to make sure that the spray arm can move freely when items have been loaded into the basket The cutlery basket Cutlery should be placed inside of the cutlery basket The cutlery basket should then be placed in the appropriate position in the lower basket 1 Teaspoons 2 Dessert spoons o Soup spoons 4 Forks 5 Knives 6 Ladle 7 Serving fork IMPORTANT Do not allow items of cutlery to fall through the bottom of the cutlery basket as this may cause damage to the spray arm and or the cutlery If the bottom of the basket begins to deteriorate and allows items to fall through you should replace the cutlery basket 17 Loading dishes and cutlery Household cloths sponges or any other object that may absorb water SHOULD NOT be washed in a dishwasher o Remove leftovers and soften the remnants of burnt food in pans prior to loading dishes in the appliance o Once the dishwasher has been loaded check that the spray arm can move freely If the spray arm comes into contact with any item then you should rearrange the wash load o Cups glasses pans etc should all be loaded with their bases upwards so that water does not collect inside of them o Cutlery and dishes should not cover each other otherwise you may get poor wash results o Do not allow glasses to touch inside
11. 18 933 6933 E mail sales baumatic co uk customercare baumatic co uk Spares baumatic co uk technical baumatic co uk Website www baumatic co uk Republic of Ireland 01 6266 798 Czech Republic Baumatic CR spol s r o Pr myslov z na Sever 696 460 11 Liberec 11 Czech Republic 420 483 577 200 www baumatic cz Slovakia Baumatic Slovakia s r o Galv niho 7 D Slovakia 421 255 640 618 Germany Baumatic Gmbh Lilienthalstrasse 1 320 52 Herford Deutschland 49 5221 694 99 0 www baumatic de Italy Baumatic Italia S R L Via Galvani N 3 35011 Campodarsego PD 3904 9920 2297 www baumatic it Holland Baumatic Benelux B V Grindzuigerstraat 22 1333 MS ALMERE Nederland 3136 549 1555 www baumatic nl 43
12. 8 gt 50 gt 35 gt 50 o The dishwasher will leave the factory with the water softener on setting 2 12 You should adjust the amount of salt that is released by the machine taking into account the water hardness of your geographical area to do this you should o Close the door of the dishwasher you will hear a mechanical click when the door of the dishwasher is shut properly o Press the ON OFF key A to switch the machine on the LED display will light up and show PO Immediately press and hold the program selection key B until the LED display is showing a flashing hO o To alter the water hardness setting use the additional rinse key D to cycle through numbers O 4 o When the LED display shows the water softener setting that you require press the program selection button to confirm your choice The LED display will show PO to indicate that the dishwasher is ready to program o If you live in a soft water area and as a result select setting 0 for the water softener there is no need to fill the water softener with dishwasher salt The salt required icon J will remain lit o IMPORTANT If you are using 3 in 1 dishwasher tablets then it may still be necessary to fill the water softener You should refer to the instructions given by the dishwasher salt manufacturer If they suggest using 3 in 1 tablets and separate dishwasher salt we would recommend that water softener setting 1 is selected Fill
13. Vac 50 Hz Maximum rated input 1 58 kW Supply connection 13 A double pole switched fused outlet with 3 mm contact gap Description of the appliance Interior of the appliance Water softener Spray ar FE t Main filter Control panel ON OFF key Program selection key Delay start key Delay start icon Additional rinse key Additional rinse icon 3 in 1 key 3 in 1 icon Start program key Digits Warning icon Salt required icon Rinse aid required icon Wash program icons Wash temperature icons Door locked icon Using your dishwasher Before first use o Install the appliance as per the installation instructions contained within this booklet o Fill the water softener with 1 litre of tap water and then fill with specialist dishwasher salt After this you should set the water softener level o Fill the rinse aid dispenser and then set the rinse aid dosage Filling with dishwasher salt IMPORTANT You should only use salt that is specially designed for use in a dishwasher If any other type of salt is used in the appliance in particular table salt it will damage the water softener o Ideally you should fill the water softener with salt just before you are about to run a wash program This will help to clear any salt that may have overflowed from the water softener during the salt filling process o Open the door of the dishwasher and then unhook the basket from the door The basket sho
14. Water outlet Drain hose hook Max 800 mm mM Min 400 mm al Y Connect the drain hose to the rear of the appliance Y Place the end of the drain hose on your drain pipe Push it a short way down into your drain pipe The drain hose should be in the shape shown in the above line drawing v IMPORTANT Do not place the drain hose higher than 800 mm v IMPORTANT Do not insert the drain hose too deeply into the water pipe as this may cause siphoning v Secure the drain hose so that it cannot move whilst the dishwasher is in use v A drain hose hook is supplied and should be attached in one of the two ways shown in the diagram below Y If you are placing the drain hose into a sink then you should make sure it is secured to the sink or use a cord to fix it in position 40 v NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH Power supply v IMPORTANT The electrical socket must still be accessible once the appliance is installed v Consult the rating plate located on the right hand of the inner surface of the door BEFORE making the electrical connections Ensure that the voltage reaching the plug is the same as that on the rating plate v DO NOT REMOVE THE RATING PLATE AS THE INFORMATION ON IT IS IMPORTANT v The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket v If you are not going to use the plug that is fitted to the power cable then the
15. al socket o The machine should not be sprayed with water o The external surface of the appliance may become hot whilst your dishwasher is in use o It is possible for small animals to chew either mains cables or water hoses which could cause an electric shock hazard Installation o The installation instructions contained within this user manual should be followed o It is obligatory for the completed installation to comply with all relevant building regulations and local water authority requirements o Before the first use of the appliance you should follow the steps listed in the Before first use section on page 11 and page 42 of this manual Care should be taken not to trap the power supply cable underneath the appliance whilst installing it No attempt should be made to alter or modify the specifications of this appliance In daily use O This appliance is only designed to wash normal domestic washloads If you use your dishwasher in any other way or it is incorrectly used then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void It is recommended that the appliance is unplugged and the water supply is turned off after the machine is used The detergents rinse aid and salt that you place in this appliance should be suitable for automatic dishwashers With regards to dosage levels the detergent manufacturer s recommendations should be followed Sharp knives or o
16. d their rear limit you should gently slide forward the upper plate only and clip this onto the drip tray catch fastener o Refit the basket IMPORTANT The drip tray MUST be in position before loading the basket and setting the appliance on a wash program The dishwasher MUST NOT BE USED without the drip tray being in position Cleaning the spray arm The spray arm should be cleaned regularly to prevent hard water deposits from clogging the spray arm jets and bearings o IMPORTANT Remove the basket before attempting to clean the spray arm o Check that the nozzles of the spray arm are not obstructed by food residue Cleaning the control panel IMPORTANT Do not use any abrasive cleaner or household polish on either the control panel or operating parts o Wipe over the control panel using a brand new damp cloth with warm water 3l Cleaning the door o To clean the edge around the outside of the door you should use a soft damp cloth only o To prevent water from penetrating the door lock or electrical components DO NOT use a spray cleaner of any kind o DO NOT use any abrasive cleaner or scouring pads on the inner or outer surfaces as they may cause damage to them Cleaning the door gasket o Use a damp sponge to clean the door gasket from time to time This will prevent the build up of food residues which could cause unpleasant odours Not using the appliance for prolonged periods If the dishwasher is not
17. described on pages 21 22 press the additional rinse key D to select the additional rinse option o The additional rinse icon D1 will light on the LED display o If you press the additional rinse key in error then it is possible to switch this option off by pressing the additional rinse key again the additional rinse icon will go out o IMPORTANT Once the wash cycle has started it is not possible to switch off the additional rinse option 3 in 1 key o IMPORTANT If you are using 3 in 1 dishwasher tablets then it may still be necessary to fill the water softener You should refer to the instructions given by the dishwasher salt manufacturer If they suggest using 3 in 1 tablets and separate dishwasher salt we would recommend that water softener setting 1 is selected o IMPORTANT If you are using 3 in 1 dishwasher tablets then it may still be necessary to fill the rinse aid dispenser You should refer to the instructions given by the rinse aid manufacturer o IMPORTANT If you are using 3 in 1 detergent tablets and not also using separate dishwasher salt and rinse aid after selecting your wash program you must press the 3 in 1 key E The 3 in 1 icon E1 will light on the LED display If your wash results are poor then we would recommend that you use a dishwasher detergent that doesn t have rinse aid and salt included in the tablet The water softener 1 and rinse aid levels should then be adjusted appropriate
18. dishwasher should be wired into a 13 A double pole switched fused spur outlet having 3 mm contact separation and placed in an easily accessible position adjacent to the appliance The spur outlet must still be accessible even when your dishwasher is located in its housing Y Broken or damaged power leads must only be replaced by a suitably qualified person A power lead of a similar type must be used in replacement v Power lead type HOVV F 3G 1 5 4 v IMPORTANT We do not recommend that this appliance is connected to an extension lead Before first use You should check the following before using the appliance for the first time That the dishwasher is level and fixed in position That the water tap is fully open That there are no leaks at either end of the drain or inlet hoses That the inlet and drain hoses are fully tightened That the inlet and drain hoses are not kinked That the power is switched on That the water softener has been filled with 1 litre of water and filled with dishwasher salt o Thatthe rinse aid dispenser has been filled OQ O O O 0 O 42 ox Baumatic United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 OQX United Kingdom Sales Telephone 0118 933 6900 Sales Fax 0118 931 0035 Customer Care Telephone 0118 933 6911 Customer Care Fax 0118 986 9124 Spares Telephone 01235 437244 Advice Line Telephone 01
19. e dishwasher salt and rinse aid after selecting your wash program you must press the 3 in 1 key E The 3 in 1 icon E1 will light on the LED display Start the wash cycle by pressing the start program key F after a few seconds you will hear the appliance begin to fill with water and the wash program will have started The door locked icon P will light and the LED display will show the time remaining until the end of the wash cycle Changing the wash program O Whilst the program number still flashes on the LED display the wash program has not been confirmed and it is possible to alter the wash program using the program selection key B Once the wash cycle is in progress we do not recommend that you attempt to change the wash program However if you do wish to do this you should press and hold down the program selection key for 3 seconds to cancel the wash cycle in progress The LED display will show 00 and you will hear the appliance pump out the water in the appliance An audible signal will sound when the appliance has finished pumping out Press the ON OFF key A to switch the appliance off You can then set a new wash program by following the setting a wash program section of this manual 22 O IMPORTANT Depending on what stage of the wash cycle has been reached it may be necessary to place a new detergent tablet detergent powder into the appliance for the new wash cycle At the end
20. e main and coarse filter back into their original positions in the base of the dishwasher You must turn the coarse filter clockwise to lock it back into position 29 IMPORTANT THE DISHWASHER SHOULD NEVER BE SET ON A WASH CYCLE WITHOUT THE FILTERS BEING INSIDE OF THE APPLIANCE The drip tray The drip tray is positioned under the basket and it is designed to catch dirt and food residue that may drop from items when they are placed in the dishwasher It is hooked directly onto the door for reasons of safety and will slide out when the door is opened o To remove the drip tray for cleaning you should firstly remove the basket from the appliance as described on pages 26 27 Drip tray catch fastener o Grip the sides of the drip tray and raise it slightly so that it unclips from the drip tray catch fastener Then push the drip tray back inside of the appliance o You should slide the upper plate of the drip tray over the lower plate of the drip tray Grip the sides of the drip tray and then remove it from the inside of the dishwasher o Clean both plates of the drip tray using hot soapy water and a damp cloth then rinse thoroughly and dry 30 Drip tray wheel Drip tray guide Plastic teeth o Slide the drip tray back into the dishwasher with the upper and lower plates closed together Making sure that the wheels locate into their guides at the side of the dishwasher tank o Once the wheels have reache
21. ess in the centre of the LED display until you hear a mechanical click This is when the door of the dishwasher is shut properly o Push the glass door back into its original position it is possible to clip it back in place by pressing the upper middle part of the glass door Setting a wash program Make sure that the Before first use section has been followed IMPORTANT The drip tray MUST be in position before loading the basket and setting the appliance on a wash program See the cleaning and maintenance section for more information o Pull out the basket and then load it in accordance with the loading instructions o Push the basket fully back into position o Place one detergent tablet into the relevant location in the cutlery basket Al Close the door firmly so that you hear the door lock click shut Press the ON OFF key A to switch the machine on the LED display will light up and show PO Check whether the salt required icon J or rinse aid required icon K are lit If they are and you usually utilise separate salt and rinse aid then before continuing with the wash program you should fill the dishwasher with salt and or rinse aid Press the program selection key B until the program that you require appears on the LED display Select any program option that you want to use e g delay start additional rinse etc IMPORTANT If you are using 3 in 1 detergent tablets and not also using separat
22. f gt gt IE C n L al USER MANUAL FOR YOUR BAUMATIC OMBRA4BL R SS W 46 cm High compact dishwasher Baumatic x _ Baumatic NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance DD 29 03 10 Environmental note 4 Important safety information 5 7 Specifications 8 Product and aperture dimensions 8 Product specifications 8 9 Energy efficiency details 9 Electrical details 9 Description of the appliance 9 10 Control panel 10 Using your dishwasher 11 19 Before first use ial Filling with dishwasher salt 11 12 Setting the water softener level 12 13 Filling with rinse aid 13 14 Setting the rinse aid level 14 15 Filling with dishwasher detergent 15 16 Loading the basket 16 17 The cutlery basket 17 Loading dishes and cutlery 18 19 Program table 20 26 Setting a wash program 21 22 Changing a wash program 22 23 At the end of a wash cycle 23 Additional rinse option 24 3 in 1 key 24 Setting a delay start 25 Rinse aid and salt indicator neons 26 Cleaning and maintenance 26 32 Removing the basket 26 27 The filter system 28 Cleaning the filters 29 30 The drip tray 30 31 Cleaning the spray arm 31 Cleaning the co
23. ies with the following European Directives 73 23 dated 19 02 1973 Low Voltage Directive and subsequent modifications 89 336 dated 03 05 1989 Electromagnetic Compatibility Directive and subsequent modifications For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice The rating plate of your dishwasher is located on the right hand side of the drop down door Model Number tee Serial Number Reel Date of Purchase aaa Specifications Product and aperture dimensions Product dimensions Aperture dimensions Height 457 mm Height 450 mm Width 598 mm Height 460 mm Depth 568 mm built under Width 560 mm Depth 560 mm Product specifications o 6 Place settings o 5 functions Normal Intensive Economy Rapid Powerful o 4 Wash temperatures 40 C 50 C 65 C 70 C o 2 Rinse temperatures 68 C 70 C Electronic aqua stop Delay start LED display Residual drying Concealed heating element Mark resistant coating stainless steel sections only Self cleaning stainless steel micro filter Anti leak device Anti flood device O O O O O O O O Low water consumption 8 litres o Noise level 49 dB Q Energy efficiency details Energy efficiency class A Washing performance class A Drying performance class A Electrical details Rated voltage 230
24. ing with rinse aid The rinse aid is released during the final rinse and it helps to prevent water from forming droplets on your dishes These droplets will lead to spots and streaks being left on items after the wash program has completed o Your dishwasher is designed to utilise liquid rinse aid o The rinse aid container is located on the inside of the dishwasher door o To access the rinse aid dispenser you should turn and remove the cap to reveal the spout 13 o Slowly pour in liquid rinse aid the rinse aid Pour the rinsa aid dispenser will hold into this spout EN Xu approximately 100ml TOS I of rinse aid You should continue to fill with rinse aid until the dispenser is full Be careful not to overfill the dispenser as this could cause oversudsing when a wash program is selected Wipe away any rinse aid excess or spillages with a damp cloth Replace the cap and turn it until it locks into position When the rinse aid required neon K lights on the control panel then you should follow the filing with rinse aid procedure again IMPORTANT If you are using 3 in 1 dishwasher tablets then it may still be necessary to fill the rinse aid dispenser You should refer to the instructions given by the rinse aid manufacturer Setting the rinse aid level The amount of rinse aid that the dishwasher requires also depends on the hardness of your water You should experiment with the rinse aid setting
25. ly for the hardness of the water in your area 24 Setting a delay start It is possible to delay the start of the wash program for a maximum of 9 hours o After you have selected a wash cycle as described on pages 21 22 press the delay start key C The LED display will show di indicating that the start of the wash cycle has been delayed by 1 hour o Continue to press the delay start key until the delay start interval that you require appears on the LED display d9 is the maximum delay start time interval that you can program 9 hours o Approximately 4 seconds after you release the delay start key the delay start icon C1 will appear on the LED display and the delay start time interval is confirmed o To commence the delay start countdown press the start program key F o After the delay time has elapsed you will hear the appliance begin to fill with water and the wash program will start o When a delay start countdown is set if you press and hold the delay start key the machine will immediately start the wash cycle that you set previously o To cancel the delay start and the wash program that you set press and hold the program selection key B until PO appears on the LED display You can then either switch the machine off or set a completely new wash program 25 Rinse aid and salt indicator neons o The rinse aid and salt indicator neons on the control panel will let you know when the
26. nes with long blades are a potential safety hazard when placed in an upright position in the cutlery basket We would recommend that these items are placed horizontally in the main basket You should not wash any items that have come into contact with corrosive acidic or alkaline chemicals paint petrol iron or steel debris You should not open the door whilst the appliance is set on a wash program Depending on which stage that the wash program is at hot water could escape the machine You should not leave the door of the appliance open unless you are loading or unloading the dishwasher You should not stand or sit on the door when it is open Child Safety O Your dishwasher should only be used by adults You should not allow children in the area of the machine unsupervised You should not let them touch the controls or play with the appliance It could be possible for a child or pet to gain access to the dishwasher if the door is left open Therefore please check the inside of the appliance before setting it on a wash cycle Any packaging that is removed from the machine should be kept away from children All detergents should be kept out of children s reach in a safe place Some water will remain inside the dishwasher when it has completed a wash cycle This water is not suitable for drinking and may contain residues from the detergents that are used in the appliance Declaration of conformity This appliance compl
27. ntrol panel 31 Cleaning the door 32 Cleaning the door gasket 32 Not using the appliance for a prolonged period 32 Reconnecting the appliance after a period of disuse 32 Error code failure system 33 34 General troubleshooting 35 36 Installation 37 42 Installing the dishwasher into a kitchen cabinet 38 39 Connecting to the mains water supply 39 Water outlet 40 41 Power supply 41 42 Before first use 42 Contact details 43 ENVIRONMENTAL NOTE Note Before discarding an old appliance switch off and disconnect it from the power supply Cut off and render any plug useless Cut the cable off directly behind the appliance to prevent misuse This should be undertaken by a competent person Disable the door lock to make sure that children cannot get stuck inside the appliance Ihis appliance is marked according to the European directive 2002 96 E C on Waste electrical and Electronic Equipment WEE E By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol zia on the product or on the documents accompanving the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in acco
28. ose page 39 and the outlet hose page 40 to the rear of the appliance o Lift the dishwasher towards the aperture and then feed the electrical cable inlet hose and outlet hose through the holes in the housing unit that you made previously 38 o Open the door of the dishwasher and then fix it to the housing unit using the four screws provided These should be screwed through the dishwasher cabinet and into the housing unit These screws must be fully tightened Connecting to the mains water supply IMPORTANT Do not connect the appliance to your mains water supply using an old or an existing water inlet hose The inlet hose supplied with the dishwasher is the ONLY one that should be used DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP o The inlet hose will be located inside the cabinet of the dishwasher o Connect the inlet hose to the inlet valve on the rear of the product Please refer to the photographs above to see the correct position that the inlet hose should be in when connected o Connect the water inlet hose to a threaded water tap that has a 3 4 thread o Fully tighten the inlet hose to the water tap and the dishwasher IMPORTANT The inlet hose is fitted with an aqua stop This MUST be fitted in the upright position as shown in the above diagram Otherwise the appliance will not operate correctly Minimum water pressure 50KPa 0 5 bar Maximum water pressure 1MPa 10 bar 39
29. rdance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office vour household waste disposal service or the shop where you purchased the product O o The packaging materials that Baumatic uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in this booklet please contact the Baumatic Advice Line General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents Any attempt by an inexperienced person to repair the appliance could result in injury or damage to your dishwasher o If you notice that the mains cable is damaged The appliance must not be used The same applies if you notice that the worktop control panel or base area is damaged As this could allow access to the internal components of the machine o The appliance should be turned off and isolated from the mains supply before either cleaning or maintenance work is attempted o The mains cable must not be used to pull the plug out of the electric
30. shwasher have not been performed Fuse in the plug has blown or there is a problem with the mains supply Dishwasher LED display is showing an error code Problems during wash cycle Routine formation of Loading error there is wash detergent in the rinse aid suds dispenser Rinse aid liquid spread over the inner door liner After filling with rinse aid remove any excess rinse aid with a damp cloth The appliance shuts Power cut down during the No water in appliance wash cycle A whining sound can A whining sound coming from the pump is not be heard during the significant There may be too much detergent or a wash cycle detergent without phosphates If the problem persists then contact the Customer Care Department Noise during cycle The spray arm is striking dishes Dishes have not been properly arranged in the basket Beating sound of the Generated by water distribution it has no effect on the inlet valve whilst mechanical operation of the appliance This type of noise filling with water is unavoidable The spray arm is blocked by some food residue and struggling to rotate should be cleaned Water is left in the The drain hose is kinked or blocked appliance at the end The drain pump has jammed of the wash cycle The filters in the base of the appliance are dirty and or filled with residue The door is difficult The appliance is not fitted correctly into the aperture to close
31. side of the appliance for too long after the wash cycle had finished No rinse aid has been added to the appliance or the rinse aid level has not been appropriately adjusted Glasses have a greyish The glasses are not suitable for washing in a looked dishwasher Stubborn traces of tea Insufficient detergent coffee or lipstick The wash cycle temperature was too low The detergent is old or has hardened or is of poor quality are stained material Damaged dishes and Type and manufacturing methods of the glasses glasses and dishes are not suitable for a dishwasher The chemical composition of the detergent is unsuitable The temperature of the water and or the duration of the wash program are not appropriate Do not leave dishes and glasses in the dishwasher for an extended period Traces of rust on the Dishes are not made completely of stainless steel dishes The water softener level has been set too high The water softener lid is not fully tightened Salt has been left in the base of the dishwasher after filling the water softener If salt spills into the base of the dishwasher then use the rapid wash to remove the salt Installation Installation of this appliance must be carried out by a suitably qualified person in accordance with the current version of the following o UK Regulations and Safety Standards or their European Norm Replacements o Building Regulations issued by the Department
32. the dishwasher otherwise damage may occur o Small objects can be placed inside of the cutlery basket o Sharp knives or ones with long blades are a potential safety hazard when placed in an upright position in the cutlery basket We would recommend that these items are placed horizontally in the main basket 18 The following items are NOT suitable for washing inside a dishwasher o Cutlery with a handle of mother of pearl wood horn or china o Plastic items that are not resistant to heat o Cutlery that consists of glued parts that are not resistant to heat o Cutlery items or crockery that are bonded o Copper or pewter items o Leadcrystal glass o Wooden platters o Synthetic fibre items The following items are not always suitable for washing inside a dishwasher o Stoneware should only be washed if the manufacturer of the item has marked it as dishwasher safe o Plastic items such as lunchboxes should only be washed if the manufacturer has marked it as dishwasher safe o Glazed crockery may fade with repeated washing inside of a dishwasher o Items made of silverware or aluminium can discolour when washed inside a dishwasher o Any food residue should be removed from silver items immediately as this can also result in discolouration o Certain types of glass may become dull or cloudy after a large number of washes 19 Program table LED display information shown P1 50 C Economy
33. uld be empty when you remove it o Turn the water softener cap anticlockwise and remove it o Pour 1 litre of water into the water softener IMPORTANT It is only necessary to do this when you fill the container with salt for the first time o Ensure that the supplied funnel is positioned correctly 11 o Pour salt into the water softener you should add approximately 1 kg of salt into the water softener o Itis perfectly normal for a small amount of water to come out of the water softener whilst you are filling it with salt This does not mean that the water softener is filed with the correct amount of salt o Refit and fully tighten the water softener cap o To remove any excess salt that may have spilled out of the water softener we would recommend that the rapid wash program is completed afterwards o When the salt required neon J lights on the control panel then you should follow the filing with dishwasher salt procedure again o IMPORTANT You do not need to pour 1 litre of water into the container when you subsequently fill the water softener with salt Setting the water softener level It is possible to regulate the amount of salt that the water softener will release during a wash cycle The water softener should be set to a level that is appropriate for the hardness of your water please refer to the table below Display dH fH Clarke mmol l 9 9 5 07510 0 7 0 1 4 2
34. until you find a level that gives the best results O The dishwasher will leave the factory with the water softener on setting A1 The rinse aid level can only be set whilst the LED display is showing PO Close the door of the dishwasher you will hear a mechanical click when the door of the dishwasher is shut properly Press the ON OFF key A to switch the machine on the LED display will light up and show PO Immediately press and hold the delay start key C until the LED display is showing A1 To alter the rinse aid setting use the additional rinse key D to cycle through AO A2 14 When the LED display shows the rinse aid setting that you require press the program selection button to confirm your choice The LED display will show PO to indicate that the dishwasher is ready to program If you get water spots and poor drying performance then the rinse aid level should be increased to a higher level You should continue to increase the rinse aid level until you get no water spots If you get cloudiness or streaking on your dishes the rinse aid level is set too high and it is causing foaming during the wash cycle The rinse aid level should be decreased to a lower level Filling with dishwasher detergent The detergent dispenser must be refilled at the start of each wash ig La TU hv T nege F 5 V Sean iw HE IF NM b F o Your dishwasher is designed to use detergent tablets
35. you should place one per wash cycle in the cutlery basket in the position shown in the above picture o If you are not placing the cutlery basket inside the dishwasher on a particular wash cycle then it is possible to place the detergent tablet in one of the corners of the drip tray see above picture 15 If you are using powder detergent this should also be placed in one of the corners of the drip tray You should refer to the manufacturer s instructions when it comes to the amount of power detergent to use per wash cycle IMPORTANT We do not recommend that you use liquid detergent in this appliance IMPORTANT If you are using 3 in 1 detergent tablets and not also using separate dishwasher salt and rinse aid then the salt required icon J and rinse aid required icon K will remain lit IMPORTANT If you are using 3 in 1 detergent tablets and not also using separate dishwasher salt and rinse aid after selecting your wash program you must press the 5 in 1 key E The 3 in 1 icon E1 will light on the LED display Loading the basket The basket is designed to wash plates up to 26 cm in diameter bowls glasses cups pots pans lids salad bowls etc Examples of appropriate ways to load the basket are shown in the pictures below o Loading without saucepans o Loading without plates 16 o Loading with a mixture of plates and saucepans o Saucepans and serving bowls must always be
Download Pdf Manuals
Related Search