Acer Aspire X1300
Contents
1. Using electrical power This product should be operated from the type of power indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company Do not allow anything to rest on the power cord Do not locate this product where people will walk on the cord If an extension cord is used with this product make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating Also make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating Do not overload a power outlet strip or receptacle by plugging in too many devices The overall system load must not exceed 80 of the branch circuit rating If power strips are used the load should not exceed 80 of the power strip s input rating This product s power supply is equipped with a three wire grounded plug The plug only fits in a grounded power outlet Make sure the power outlet is properly grounded before inserting the power supply plug Do not insert the plug into a non grounded power outlet Contact your electrician for details Warning The grounding pin is a safety feature Using a power outlet that is not properly grounded may result in electric shock and or injury Note The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with2. focusing on a distant point Blink frequently to keep your eyes from drying out Display Keep your display clean Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display e Adjust the display brightness and or contrast to a comfortable level for enhanced text readability and graphics clarity Eliminate glare and reflections by placing your display in such a way that the side faces the window or any light source minimizing room light by using drapes shades or blinds using a task light e changing the display s viewing angle using a glare reduction filter using a display visor such as a piece of cardboard extended from the display s top front edge e Avoid adjusting your display to an awkward viewing angle e Avoid looking at bright light sources such as open windows for extended periods of time Developing good work habits Develop the following work habits to make your computer use more relaxing and productive e Take short breaks regularly and often Perform some stretching exercises Breathe fresh air as often as possible Exercise regularly and maintain a healthy body Warning We do not recommend using the computer on a couch or bed If this is unavoidable work for only short periods take breaks regularly and do some stretching exercises Information for your safety and comforti Safety ins
3. the use of your computer and each is followed by easy answers and solutions to the situation Q pressed the power switch but the system did not boot up A Check the LED located above the power switch If the LED is not lit no power is being applied to the system Do any of the following e Check if the voltage selector switch located on the rear panel of the computer is set to the correct voltage e Check if you plugged the power cable properly into an electrical outlet e Ifyou are using a power strip or AVR make sure that it is plugged in and turned on If the LED is lit check the following e Is anon bootable non system diskette in the floppy drive If yes remove or replace it with a system diskette and press Ctrl Alt Del to restart your computer e The operating system files may be damaged or missing Insert the start up disk you created during Windows setup into the floppy drive and press Ctrl Alt Del to restart your computer This will automatically diagnose your system and make necessary fixes However if the diagnostic utility still reports a problem then you may have to perform the recovery process to restore your system to its original default factory settings Note For more information about recovering your system refers to the RCD instruction sheet Q Nothing appears on the screen A Your computer s power management function automatically blanks the screen to save power Just press any key t
4. Hungary Czech Republic Slovak Republic Slovenia Cyprus and Malta Bulgaria and Romania Usage allowed in the countries of the European Union as well as Norway Switzerland Iceland and Liechtenstein This device must be used in strict accordance with the regulations and constraints of the country of use For further information please contact the local office in the country of use 13 acer Acer America Corporation 333 West San Carlos St San Jose CA 95110 U S A Tel 254 298 4000 Fax 254 298 4147 www acer com C Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The following local Manufacturer Importer is responsible for this declaration Product Personal Computer Trade Name Acer Model Number AcerSystem SKU Number XXX XXX x 0 9 a z A Z or Blank Name of Responsible Party Acer America Corporation Address of Responsible Party 333 West San Carlos St San Jose CA 95110 U S A Contact Person Acer Representative Phone No 254 298 4000 Fax No 254 298 4147 14 acer Acer Incorporated 8F 88 Sec 1 Hsin Tai Wu Rd Hsichih Taipei Hsien 221 Taiwan Declaration of Conform
5. of our environment The more energy we can save through higher energy efficiency the more we reduce greenhouse gases and the risks of climate change More information refers to http Awww energystar gov or http www energystar gov powermangement Note The statement above is applicable only to Acer system with an ENERGY STAR sticker Acer ENERGY STAR qualified products Produce less heat and reduce cooling loads and warmer climates e Automatically go into display sleep and computer sleep mode after 10 and 30 minute of inactivity respectively e Wake the computer from sleep mode by pushing keyboard or moving mouse Computers will save more than 80 energy at sleep mode ENERGY STAR and the ENERGY STAR mark are registered U S marks Tips and information for comfortable use Computer users may complain of eyestrain and headaches after prolonged use Users are also at risk of physical injury after long hours of working in front of a computer Long work periods bad posture poor work habits stress inadequate working conditions personal health and other factors greatly increase the risk of physical injury Incorrect computer usage may lead to carpal tunnel syndrome tendonitis tenosynovitis or other musculoskeletal disorders The following symptoms may appear in the hands wrists arms shoulders neck or back numbness or a burning or tingling sensation aching soreness or tenderness pain swelling or
6. the performance of this product Use the product only with the supplied power supply cord set If you need to replace the power cord set make sure that the new power cord meets the following requirements detachable type UL listed CSA certified VDE approved or its equivalent 4 6 meters 15 feet maximum length Product servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage points or other risks Refer all servicing to qualified service personnel Unplug this product from the wall outlet and refer servicing to qualified service personnel when e the power cord or plug is damaged cut or frayed liquid was spilled into the product e the product was exposed to rain or water e the product has been dropped or the case has been damaged e the product exhibits a distinct change in performance indicating a need for service e the product does not operate normally after following the operating instructions Note Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructi
7. throbbing stiffness or tightness coldness or weakness If you have these symptoms or any other recurring or persistent discomfort and or pain related to computer use consult a physician immediately and inform your company s health and safety department The following section provides tips for more comfortable computer use Finding your comfort zone Find your comfort zone by adjusting the viewing angle of the monitor using a footrest or raising your sitting height to achieve maximum comfort Observe the following tips refrain from staying too long in one fixed posture avoid slouching forward and or leaning backward stand up and walk around regularly to remove the strain on your leg muscles e take short rests to relax your neck and shoulders avoid tensing your muscles or shrugging your shoulders install the external display keyboard and mouse properly and within comfortable reach if you view your monitor more than your documents place the display at the center of your desk to minimize neck strain vi Taking care of your vision Long viewing hours wearing incorrect glasses or contact lenses glare excessive room lighting poorly focused screens very small typefaces and low contrast displays could stress your eyes The following sections provide suggestions on how to reduce eyestrain Eyes Rest your eyes frequently Give your eyes regular breaks by looking away from the monitor and
8. AcerSystem User Guide Copyright 2009 All Rights Reserved AcerSystem User Guide Visit http registration acer com and discover the benefits of being an Acer customer Information for your safety and comfort Safety instructions Read these instructions carefully Keep this document for future reference Follow all warnings and instructions marked on the product Turning the product off before cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning CAUTION for plug as disconnecting device Observe the following guidelines when connecting and disconnecting power to the power supply unit Install the power supply unit before connecting the power cord to the AC power outlet Unplug the power cord before removing the power supply unit from the computer If the system has multiple sources of power disconnect power from the system by unplugging all power cords from the power supplies CAUTION for accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible When you need to disconnect power to the equipment be sure to unplug the power cord from the electrical outlet Warnings Do not use this product near water Do not place this product on an unstable cart stand or table If the product falls it could be seriously damaged
9. S PDIF port selected models only selected models only E PS 2 keyboard connector PS 2 mouse connector VGA port Serial port selected models only gt Printer connector USB port selected models only Microphone in jack RJ 45 Ethernet connector e e Ny Ie iD Line in jack Line out Speaker out jack QY Q HDMI port ESATA port selected models only selected models only 2 Setting up your computer Note The specifications listed above are for reference only The exact configuration of your PC depends on the model purchased Setting up your computer The AcerSystem is a versatile and powerful system supporting a mainstream performance CPU The computer uses a state of the art bus architecture which improves system efficiency and helps the system support varied multimedia and software applications Your AcerSystem has standard I O input output interfaces such as a parallel port PS 2 keyboard and mouse ports USB 2 0 ports and stereo microphone line in and line out jacks configuration may vary by models The system can accommodate extra peripheral equipment through these I O ports Your system can also support an optional high speed fax data modem or an additional LAN local area network card Furthermore the system is compatible with Microsoft Windows or Linux based operating systems Necessary to know before setup Selecting a location Selecting the optimum lo
10. Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register or in a built in installation unless proper ventilation is provided Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind onto or into the product e To avoid damage of internal components and to prevent battery leakage do not place the product on a vibrating surface Never use it under sporting exercising or any vibrating environment which will probably cause unexpected short current or damage rotor devices HDD Optical drive and even exposure risk from lithium battery pack Safe listening Follow these instructions suggested by hearing experts to protect your hearing Gradually increase the volume until you can hear it clearly and comfortably and without distortion After setting the volume level do not increase it afteryour ears adjust Limit the amount of time listening to music at high volume Avoid turning up the volume to block out noisy surroundings Turn the volume down if you can t hear people speaking near you
11. Some parameters required for compliance with Telecom s Telepermit requirements are dependent on the equipment PC associated with this device The associated equipment shall be set to operate within the following limits for compliance with Telecom s Specifications a There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation and b The equipment shall go on hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next call attempt Some parameters required for compliance with Telecom s Telepermit requirements are dependent on the equipment PC associated with this device In order to operate within the limits for compliance with Telecom s specifications the associated equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is not less than 5 seconds between the end of one call attempt and the beginning of another This equipment shall not be set up to make automatic calls to Telecom s 111 Emergency Service This device is equipped with pulse dialing while the Telecom standard is DTMF tone dialing There is no guarantee that Telecom lines will always continue to support pulse dialing Use of pulse dialing when this equipment is connected to the same line as other equipment may give rise to bell tinkle or noise and may also cause a false answer condition Should such problems occ
12. cation for your computer e Do not place the system too close to other electrical equipment e Do not place the system in high traffic areas or where the power cord or other cords may be stepped on e Avoid placing the system in any location that is excessively dusty or damp CAUTION Please use the foot stand when placing your PC in the upright position Opening the package Open the package carefully and keep all packing materials for later use Ensure that all items are present and in good condition If any of the following items are missing or appear damaged contact your dealer immediately e AcerSystem e Mouse PS 2 or USB e Keyboard PS 2 or USB e Wireless keyboard with pointing function e Remote control for Microsoft Windows Media Center Edition Note Mouse keyboard wireless keyboard or remote control configuration may vary by selected models e User s Guide and Starter poster Other user documentation and third party software Connecting peripherals After everything is connected plug the power cord into the system and insert the other end into a power outlet Note Don t connect the system power cord before connecting all peripherals to the system Starting your computer After connecting all the peripheral equipment start your computer according to the steps below 1 Turn on all peripheral equipment such as the monitor printer fax speakers etc 2 Turn on the system Once the start up pr
13. cer com support index htm for information on how and where to contact the service centers available in your area Regulations and safety notices FCC notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the device off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help Notice Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations In compliance with FCC regulations use shielded cables to connect to other computing
14. devices A dual link cable is recommended for DVI output Notice Peripheral devices Only peripherals input output devices terminals printers etc certified to comply with the Class B limits may be attached to this equipment Operation with non certified peripherals is likely to result in interference to radio and TV reception Caution Changes or modifications not expressly approved by the manufacturer could void the user s authority which is granted by the Federal Communications Commission to operate this computer 10 Operation conditions This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Notice Canadian users This Class B digital apparatus complies with Canadian ICES 003 Remarque a l intention des utilisateurs canadiens Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Declaration of Conformity for EU countries Hereby Acer declares that this PC series is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Compliant with Russian regulatory certification ME61 List of applicable countries EU member states as of July 2009 are Belgium Denmark Germany Greece Spain France Ireland Italy Luxemb
15. ity We Acer Incorporated 8F 88 Sec 1 Hsin Tai Wu Rd Hsichih Taipei Hsien 221 Taiwan Contact Person Mr Easy Lai e mail easy_lai acer com tw And Acer Europe SA Via Cantonale Centro Galleria 2 6928 Manno Switzerland Hereby declare that Product Personal Computer Trade Name Acer Model Number AcerSystem SKU Number XXX xxx x 0 9 a z A Z or Blank Is compliant with the essential requirements and other relevant provisions of the following EC directives and that all the necessary steps have been taken and are in force to assure that production units of the same product will continue comply with the requirements EMC Directive 2004 108 EC as attested by conformity with the following harmonized standards EN55022 AS NZS CISPR22 Class B EN55024 EN55013 Applicable to product built with TV tuner modue EN55020 Applicable to product built with TV tuner module EN61000 3 2 Class D EN61000 3 3 Low Voltage Directive 2006 95 EC as attested by conformity with the following harmonized standard EN60950 1 EN60065 Applicable to product built with TV tuner module Council Decision 98 482 EC CTR21 for pan European single terminal connection to the Public Switched Telephone Network PSTN RoHS Directive 2002 95 EC on the Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment The maximum concentration values of the restricted substances by weight in h
16. o turn the display back on If pressing a key does not work you can restart your computer If restarting your computer does not work contact your dealer or the technical support center for assistance Q The printer does not work A Do the following e Make sure that the printer is connected to a power outlet and that it is turned on e Make sure that the printer cable is connected securely to the system s parallel port and the corresponding port on the printer e For additional information concerning the printer refer to the printer s documentation Q No sound comes out from the computer A Check the following e The volume may be muted Look for the Volume icon on the taskbar If it is crossed out click on the icon and deselect the Mute option You can also press the volume control mute knob on your USB keyboard to toggle from mute to sound on e If headphones earphones or external speakers are connected to the line out jack of your computer the internal or built in speakers are automatically turned off Q System cannot read diskette hard disk CD or DVD information A Check the following e Make sure that you are using the correct type of disk e Make sure the CD or DVD is inserted into the drive correctly e Check if the CD or DVD is clean and not scratched e Check your drive by using a good i e undamaged disk If your drive cannot read the information on the good disc there may be a problem
17. ocess is complete you can begin to use your computer Shutting down your computer From the Start menu select Shut Down and click OK 4 Setting up your computer In the event of a system crash press and hold the power button on the front of the system for four seconds After the system has shut down turn off all peripheral devices System upgrade You can expand your AcerSystem system quickly and easily by adding components You can also upgrade the components of your AcerSystem system Opening the computer Before removing any panels or covers please make sure to shut off the computer and unplug the power cord from the outlet e Remove the screws on the chassis e Slide the panel off Setting up new components You can only use components compatible with AcerSystem computers Before you choose new components please ask your authorized Acer dealer whether the part will operate within your AcerSystem system In order to ensure proper setup and installation please refer to the instructions provided with your new components Probable upgrades are e Upgrade to high capacity HDD e Expand high level memory e Upgrade from a CD ROM drive to CD RW DVD ROM DVD CD RW combo or DVD write selected models only r e Install additional interface cards in empty PCI slots e g PCI fax modem card selected models only Frequently asked questions The following questions are possible situations that may arise during
18. omogenous material are Lead 0 1 Polybrominated Biphenyls PBB s 0 1 Mercury 0 1 Polybrominated Diphenyl Ethers PBDE s 0 1 Hexavalent 0 1 Cadmium 0 01 Chromium 15 The standards listed below are applied to the product if built with WLAN module or wireless keyboard and mouse CE R amp TTE Directive 1999 5 EC as attested by conformity with the following harmonized standard e Article 3 1 a Health and Safety EN60950 1 EN62311 e Article 3 1 b EMC EN301 489 1 EN301 489 3 Applicable to non bluetooth wireless keyboard mouse set EN301 489 17 e Article 3 2 Spectrum Usages EN300 440 2 Applicable to non bluetooth wireless keyboard mouse set EN300 328 EN301 893 Applicable to 5GHz high performance RLAN Year to begin affixing CE marking 2009 Cas oe Jul 9 2009 Easy ti Manager Date Regulation Center Acer Inc 16 Remark All images are for reference purposes only Actual configuration may vary VO9A3
19. ons Additional safety information Your device and its enhancements may contain small parts Keep them out of the reach of small children Disposal instructions Do not throw this electronic device into the trash when discarding To minimize pollution and ensure utmost protection of the global environment please recycle For more information on the Waste from Electrical and iv Electronics Equipment WEEE regulations visit http Awww acer group com public Sustainability sustainability01 htm Mercury advisory For projectors or electronic products containing an LCD CRT monitor or display Lamp s inside this product contain mercury and must be recycled or disposed of according to local state or federal laws For more information contact the Electronic Industries Alliance at www eiae org For lamp specific disposal information check www lamprecycle org ENERGY STAR Acer s ENERGY STAR qualified products save your money by reducing energy cost and protecting the environment without sacrificing features or performance Acer is proud to offer our customers products with the ENERGY STAR mark What is ENERGY STAR Products that are ENERGY STAR qualified use less energy and prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the U S Environmental Protection Agency Acer is committed to offer products and services worldwide that help customers save money conserve energy and improve the quality
20. ourg the Netherlands Austria Portugal Finland Sweden United Kingdom Estonia Latvia Lithuania Poland Hungary Czech Republic Slovak Republic Slovenia Cyprus and Malta Bulgaria and Romania Usage allowed in the countries of the European Union as well as Norway Switzerland Iceland and Liechtenstein This device must be used in strict accordance with the regulations and constraints of the country of use For further information please contact the local office in the country of use Notice for Australia For safety reasons only connect headsets with a telecommunications compliance label This includes customer equipment previously labelled permitted or certified 11 Notice for New Zealand 1 The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network It indicates no endorsement of the product by Telecom nor does it provide any sort of warranty Above all it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model nor does it imply that any product is compatible with all of Telecom s network services This equipment is not capable under all operating conditions of correct operation at the higher speeds for which it is designed Telecom will accept no responsibility should difficulties arise in such circumstances
21. ting Cleaning and servicing To clean your computer and keyboard 1 2 Turn off the computer and unplug the power cord Use a soft cloth moistened with water and gently wipe the exterior of the computer and the keyboard Do not use liquid or aerosol cleaners To clean your pointing device To clean a regular mouse with rubber ball 1 Open the circular cover at the base of the mouse 2 Take out the rubber ball and wipe it with a soft damp cloth 3 Put the ball back and replace the cover To clean an optical mouse For users of an optical mouse refer to the documentation that came with your mouse for maintenance instructions To clean your monitor Make sure that you keep your screen clean For cleaning instructions refer to the documentation that came with your monitor When to contact a service technician e Ifyou dropped and damaged the computer e If liquid has been spilled into the computer e Ifthe computer is not operating normally e If a computer problem persists even after you have checked and applied the troubleshooting tips discussed in the Frequently asked questions section on page 5 e If your problem is not listed in the Frequently asked questions section on page 5 e Ifyou want to replace or upgrade any of your computer s internal components Asking for technical assistance For technical assistance contact your local dealer or distributor You may also access the Web site http global a
22. tructions Additional safety information Disposal instructions Tips and information for comfortable use System tour Setting up your computer Necessary to know before setup Selecting a location Opening the package Connecting peripherals Starting your computer Shutting down your computer System upgrade Opening the computer Setting up new components Frequently asked questions Taking care of your computer Important tips Cleaning and servicing To clean your computer and keyboard To clean your pointing device To clean your monitor When to contact a service technician Asking for technical assistance Regulations and safety notices FCC notice Laser compliance statement Digital audio output statement Radio device regulatory notice General Federal Communications Commission Wnwnonvunyn N Uananannnwnnn N Se Contents Remark All images are for reference purposes only Actual configuration may vary System tour Your computer consists of the following Power button Floppy drive selected models only Optical drive selected models only Microphone jack ORIG amp VE Speaker or Media card reader headphone jack selected models only s USB port IEEE 1394 FireWire jack ei selected models only Copy button Backup button selected models only selected models only Media navigation Removable hard interface drivecarriers selected models only selected models only RCA jack
23. ur the user should NOT contact the telecom Fault Service This equipment may not provide for the effective hand over of a call to another device connected to the same line Under power failure conditions this appliance may not operate Please ensure that a separate telephone not dependent on local power is available for emergency use 12 Laser compliance statement The CD or DVD drive used with this computer is a laser product The CD or DVD drive s classification label shown below is located on the drive CLASS 1 LASER PRODUCT CAUTION INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM Digital audio output statement The optical connector contains no laser or light emitting diode LED more than Class I Radio device regulatory notice Note Below regulatory information is for models with wireless LAN and or Bluetooth only General This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use Depending on configurations this product may or may not contain wireless radio devices such as wireless LAN and or Bluetooth modules Below information is for products with such devices List of applicable countries EU member states as of July 2009 are Belgium Denmark Germany Greece Spain France Ireland Italy Luxembourg the Netherlands Austria Portugal Finland Sweden United Kingdom Estonia Latvia Lithuania Poland
24. with the drive Contact your dealer or technical support center for assistance Q System cannot write data on the hard disk or writeable re writeable disk A Check the following e Make sure the diskette or hard disk is not write protected e Make sure that you are using the correct type of disk or diskette Taking care of your computer Please read the important instructions listed in this section Following these instructions will help you maximize the durability of your computer Important tips Do not expose the computer to direct sunlight Do not place it near sources of heat such as a radiator Do not expose the computer to temperatures below 0 C 32 F or above 50 C 122 F Do not subject the computer to magnetic fields Do not expose the computer to rain or moisture Do not spill liquid on the computer Do not subject the computer to heavy shock or vibration Do not expose the computer to dust and dirt Never place the system on uneven surfaces Do not step on the power cord or place heavy objects on top of it Carefully route the power cord and any cables away from personal traffic When unplugging the power cord do not pull on the cord itself but pull on the plug The total ampere rating of the equipment plugged in should not exceed the ampere rating of the cord if you are using an extension cord Also the total current rating of all equipment plugged into a single wall outlet should not exceed the fuse ra
Download Pdf Manuals
Related Search