Siig JU-SW4112
Contents
1. Computer click Properties then click Device Manager 2 Depending on the status of the Power LED Manual Switching Button use the option that best matches the system Power LED 1s lit Double click Universal Serial Bus controllers and Generic USB Hub should be displayed Power LED is off Double click Human Interface Devices HID compliant device and either USB Human Interface Device or USB Input Device should be displayed Windows Device Switching Hotkey Control Status Indicator and Manual switching button are the three methods that can be used to switch devices between systems Note For Mass Storage devices such as flash drives USB memory card readers and CD ROMs before switching the USB device to another system it must be released from the system that controls it Use Windows Safely Remove Hardware feature located in the taskbar to Stop the USB device Hotkey Control Press Ctrl F11 to switch the USB device to the current system Status Indicator L The Status Indicatoris located in the taskbar by the system clock The indicator has three functions Red Another system is accessing the device switching not allowed Green The current system controls the device Yellow No system controls the device switching is allowed 2 Double click the USB Sharing icon to start USB sharing program manually 3 Right click the Status Indicator and select Switch can also switch USB access to the current system2. Note Devices such as external hard drives and printers send signals back and forth to your computer when they are connected This causes the Status Indicator to remain red Switching is still possible by clicking Yes in the Enforce Switching pop up box Manual Switching Button Press a Power LED Manual switching button to switch to another system Mac OS Installation No driver installation is necessary Simply plug the USB 2 0 Switch into an available USB port USB 2 0 recommended Mac OS Device Switching Device switching is controlled by the Power LED Manual switching button Follow the instructions in the next section for your device type Memory Card Readers 1 Drag the memory card s driveicon into the Trashcan 2 Remove the memory card from the card reader then press a switching button to change systems 3 Insert a memory card into the memory card reader Mass Storage Devices CD ROMs flash drives external hard disk drives and Zip drives typically add drive icons to the desktop Use the directions below for switching these devices 1 Drag the drive icon into the Trashcan 2 Press the switching button to change systems 3 The drive icon will appear on the other system Other Devices For other devicesjust press the switching button to change to another system Connecting USB Devices When connecting your USB device s to the USB 2 0 Switch follow the USB device s driver installation procedures Te
3. USB 2 0 Switch 2 to 1 USB 2 0 Switch 4 to 1 Four Type B connectors for system connection One Type A connector for device connection Convenient manual switching buttons Power LED Manual switching button To PC Type B connector To PC Type B connector To USB device Type A connector Figure 2 USB 2 0 Switch 4 to 1 Windows Installation Important Do not connect the USB 2 0 Switch to your system until after the driver has been installed In order for the driver to install properly the Power LED to that system must be switched to another system For example if you connect port A to system A make sure the Power LED on port A is not lit Windows 7 32 64 bit Windows Vista 32 64 bit L ol a Te Insert the driver CD after Windows boots At the AutoPlay box Click Run Setup exe If AutoPlay doesn t start Click Start in Start Search type D Setup exe press Enter Change D to match your CD DVD ROM drive letter At User Account Control click Allow Select your language then click OK Click Next Next then Finish Plug the USB 2 0 Switch into an available USB port USB 2 0 recommended with the supplied USB cables and the driver will install automatically Press the Power LED Manual switching button that matches the system to complete the installation Windows XP 32 64 bit Server 2003 32 64 bit l 2 a Insert the driver CD after Windows boots AutoRun should start the in
4. cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 USB 2 0 Switch is a trademark of SHG Inc SUG and the SIIG logo are registered trademarks of SHG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation Mac and Mac OS are registered trademarks of Apple Computer All other names used in this publication are for identification only and may be trademarks of their respective owners April 2010 Copyright 2010 by SIG Inc All rights reserved
5. chnical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a 5 year manufacturer warranty with this product Please see our web site for more warranty details If youencounter any problems with this product please follow the procedures below If it is within the store s return policy period please return the product to the store where you purchased from If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SIG RMA Your RMA request will be processed if the product is determined to be defective an RMA number willbe issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youareresponsible for the
6. commended with the supplied USB cables and the driver will install automatically Press the Power LED Manual switching button that matches the system to complete the installation Windows 98SE L 2 Insert the driver CD after Windows boots AutoRun should start the installation If AutoRun doesn t start click Start Run type D setup exe then click OK Change D to match yourCD DVD ROM drive letter Select your language then click OK Click Next Next then Finish Restart Windows When Windows resumes plug the USB 2 0 Switch into an available USB port USB 2 0 recommended with the supplied USB cables When Windows prompts for the driver click Next rs Select Search for the best driver and click Next 8 Clear all check boxes click Next click Next again Note If prompted for Windows Installation CD ROM click OK Insert this CD then click OK again 9 Click Finish If prompted click Yes to restart To Verify Windows Installation 1 Go to Device Manager to verify installation For Windows 7 Right click Computer click Manage then click Device Manager For Windows Vista Right click Computer click Manage click Continue then click Device Manager For Windows XP Server 2003 2000 Right click My Computer click Manage then click Device Manager For Windows Server 2008 Right click Computer click Manage double click Diagnostics then click Device Manager For Windows ME 98SE Right click My
7. cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 11 About SIIG Inc Founded in 1985 SIIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio SIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME USB 2 0 Switch FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not
8. l USB 2 0 Switch UJ Quick Installation Guide Introducing the USB 2 0 Switch The USB 2 0 Switch is designed to share USB device s between multiple systems Features and Benefits Compliant with USB Specifications Revision 2 0 Hot swapping feature allows you to attach detach USB devices without powering down your computer Use keyboard Hotkey control Windows only or Power LED Manual switching button to switch between computers Designed for USB devices including printers scanners hard disk drives cameras CD ROMS and Zip drives Note Not designed to work with keyboard or mouse System Requirements PC or Mac computer with an available USB port USB 2 0 recommended Windows 7 32 64 bit Vista 32 64 bit XP 32 64 bit Server 2003 amp 2008 32 64 bit 2000 ME 98SE Mac OS X v10 0 or later 04 0318C 1 Package Contents USB 2 0 Switch e USB cables 6 Ft Type A to Type B Software CD and quick installation guide Layout Do not connect the USB 2 0 Switch to your system until after the driver has been installed Please refer to the Installation section starting on page 4 to install its driver USB 2 0 Switch 2 to 1 e Two Type B connectors for system connection One Type A connector for device connection Convenient manual switching buttons To PC Type B connector DE Power LED Manual switching button EJ To USB device Type A connector Figure 1
9. stallation If AutoRun doesn t start click Start Run type D setup exe then click OK Change D to match your CD DVD ROM derive letter Select your language then click OK Click Next Next then Finish Plug the USB 2 0 Switch into an available USB port USB 2 0 recommended with the supplied USB cables and the driver will install automatically Press the Power LED Manual switching button that matches the system to complete the installation Windows Server 2008 32 64 bit 1 a Insert the driver CD after Windows boots At the AutoPlay box Click Run Setup exe If AutoPlay doesn t start Click Start in Start Search type D Setup exe press Enter Change D to match your CD DVD ROM drive letter Select your language then click OK Click Next Next then Finish Plug the USB 2 0 Switch into an available USB port USB 2 0 recommended with the supplied USB cables and the driver will install automatically Press the Power LED Manual switching button that matches the system to complete the installation 5 Windows 2000 ME I Insert the driver CD after Windows boots AutoRun should start the installation If AutoRun doesn t start click Start Run type D setup exe then click OK Change D to match your CD DVD ROM drive letter Select your language then click OK Click Next Next then Finish Restart Windows When Windows resumes plug the USB 2 0 Switch into an available USB port USB 2 0 re
Download Pdf Manuals
Related Search