Siig Cyber I/O PCI
Contents
1. SP2 or later Server 2003 wSP1 or later select No not this time click Next 2 Select Install the software automatically Recommended then click Next 3 Click Finish Repeat steps 1 3 two more times e 5 Restart Windows to complete the installation 64 bit Windows XP Server 2003 1 At the Found New Hardware Wizard insert the driver CD For XP w SP1 or earlier Server 2003 go to step 2 For XP w SP2 or later Server 2003 wSP1 or later select No not this time click Next 2 Select Install the software automatically Recommended then click Next 3 Click Continue Anyway then click Finish 4 Repeat steps 1 3 several more times 5 Restart Windows to complete the installation To Verify Windows 2000 XP 2003 Installation 1 Rightclick My Computer click Manage then select Device Manager 2 Double click Ports COM amp LPT CyberSerial PCI 16Cxxx andCyberParallel PCI should be displayed 3 Double click Multifunction adapters SIIG CyberPro 1S1P PCI board should be displayed Windows Vista 1 At the Found New Hardware window insert the driver CD click Locate and install driver software recommended then click Continue Click Next then click Close Repeat step 2 to complete the driver installation Note Windows Vista driver installation process may take several minutes to complete To Verify Windows Vista Installation T Rightclick Computer click Manage click Conti2. A number willbe issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in1985 SNG Inc isa leading computer upgrade manufacturer of 1 Oconnectivity products including PCI amp ISA serialand parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the indu
3. P PCI board should be displayed Windows NT 4 0 1 From the desktop click Start then Run 2 Insert the driver CD type in D NT4 Install_Serial exe then click OK Change D to match your CD ROM drive letter Click Next when the Welcome window appears Choose Install then click Next Click Yes then click Exit From the desktop click Start then Run ot e g Typein D NT4 Install_Parallel exe then click OK Change D to match your CD ROM drive letter Repeat steps 3 5 Click Yes to restart Windows to complete the installation To Verify Windows NT 4 0 Installation 1 Goto Start Settings Control Panel double click Ports device icon 2 Anew COM port willbeassigned when successfully installed 3 Click Start Programs Administrative Tools Windows NT Diagnostics Click Resources tab SIIGpar and SIIGser should be displayed Windows 2000 1 At the Found New Hardware Wizard click Next 2 Select Search for a suitable driver for my device recommended and click Next 3 Select Specify a location uncheck the other boxes and click Next 4 Insert the driver CD type in D 2000 then click OK Change D to match your CD ROM drive letter 5 Click Next and Finish 6 Repeat steps 1 5 two more times 7 Restart Windows to complete the installation 32 bit Windows XP Server 2003 1 At the Found New Hardware Wizard insert the driver CD For XP w SP1 or earlier Server 2003 go to step 2 For XP w
4. le use of I O location 278h Click OK click OK again to close Device Manager and click Yes to restart Windows to save the changes Windows 2000 XP Server 2003 Vista 1 From the Device Manager window double click Ports COM amp LPT then doubleclick CyberParallel PCI Click Port Settings tab At the LPT Port Number box click the down arrow and select an LPT port that is not in use Click OK then close Device Manager to save the changes Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RM
5. nue then click Device Manager Click on the plus sign in front of Ports COM amp LPT CyberSerial PCI 16Cxxx and CyberParallel PCI should be displayed Double click Multifunction adapters SIIG CyberPro 1S1P PCI board should be displayed Changing COM Port Address Some serial devices need a specific COM port in order to work If your serial device works properly do not change this setting Windows 95 98 98SE ME 1 From the Device Manager window double click Ports COM amp LPT then double click CyberSerial PCI serial port Click Settings tab at the Port Name box click the down arrow and select a COM address that is not currently in use Click OK click OK again to close Device Manager to save the changes Windows 2000 XP Server 2003 Vista 1 From the Device Manager window double click Ports COM amp LPT then double click CyberSerial PCI serial port Click Settings tab and click Advanced Atthe COM Port number box click the down arrow and select a COM port that is not in use Click OK Click OK then close Device Manager to save the changes Changing Parallel Port Address LPT Some parallel devices need a specific parallel port in order to work If your parallel device works properly do not change this setting Windows 95 98 98SE ME 1 From the Device Manager window double click Ports COM amp LPT then double click CyberParallel PCI Click Settings tab check Enab
6. sA Cyber 1S1P PCI C Quick Installation Guide Introducing the Cyber 181P PCI The Cyber 1S1P PCI high speed serial I O card provides one 9 pin serial port and one parallel port Features and Benefits e Conforms to PCI v2 2 Plug and Play e Full support for Windows based software e Reduces CPU load and improves system performance dramatically e IRQ sharing feature reduces IRQ conflicts e High speed serial port 9 pin works with 56K V 90 external modems ISDN terminal adapters PDAs digital cameras label printers and other serial port devices e Built in FIFO buffers dramatically increase data transmit receive speed especially under Windows multitasking environment e Each serial port can be configured for either 5v or 12v output for serial devices that require power e IEEE 1284 compliant SPP EPP ECP parallel port System Requirements e Pentium or equivalent computer with an available PCI slot e Windows 95 98 98SE ME NT 4 0 2000 XP 32 64 bit Server 2003 32 64 bit Vista 32 64 bit 04 0344C 1 Package Contents e Cyber 151P PCI board e DriverCD e Quick Installation Guide Layout JP1 Serial Port Parallel Port ni aii 1 Figure 1 Layout Jumper Settings JP1 Open 0 volts default Short 1 2 5V Short 2 3 12V Note Most serial devices do not require additional power through the serial port Refer to your serial device s manual for more information This jumper can be remo
7. stry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and throughe commerce sites PRODUCT NAME Cyber 1S1P PCI FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SHG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Cyber 1S1P PCTis a trademark of SHG Inc SIIG and the SHG logo are registered trademarks of SIG Inc Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation Other names used in this publication are for identification only and may be trademarks of their respective companies October 2007 Copyright 2007 by SIG Inc All rights reserved
8. ved if it s not used Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges T Turn OFF the power to your computer and any other connected peripheral devices Unplug the power cord from the back of the computer Remove your computer s cover Remove the slot bracket from an available PCI slot Set JP1 jumper settings to the desired voltage only if your serial device needs additional power from the serial port However most serial devices do not require additional power For more information see Figure 1 on page 2 Skip this step if power is not required To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card Replace the computer cover and reconnect the power cord Driver Installation This section provides information on how to install the Cyber 151P PCI drivers Windows 95 1 At the Update Device Driver Wizard
9. window click Next 2 Insert the driver CD and click Other Locations Type in D 9x click OK then Finish Change D to match your CD ROM drive letter 3 From the Insert Disk window click OK When the Copying Files dialog box appears type in D 9x then click OK 4 Repeat steps 1 3 5 Restart Windows to complete the installation Windows 98 98SE 1 Atthe Add New Hardware Wizard window click Next 2 Select Search for the best driver for your device Recommended then click Next 3 Select Specify a location uncheck the other boxes insert the driver CD type in D 9x then click Next Change D to match your CD ROM drive letter 4 Click Next then Finish 5 Repeat steps 1 4 6 Restart Windows to complete the installation Windows ME 1 Atthe Add New Hardware Wizard choose Specify the location of the driver Advanced then click Next 2 Check Specify a location uncheck the other box insert the driver CD typein D Me then click Next Change D to match your CD ROM drive letter 3 Click Next and Finish 4 Repeat steps 1 3 5 Restart Windows to complete the installation To Verify Windows 95 98 98SE ME Installation 1 From the main desktop right click My Computer click Properties then click Device Manager 2 Double click Ports COM amp LPT CyberSerial PCI 16Cxxx Printer Port and CyberParallel PCI should be displayed 3 Double click Multi function adapters SIIG CyberPro 1S1
Download Pdf Manuals
Related Search