Siig 2S1P Combo-Value
Contents
1. Figure 1 Layout Note When connecting the DB9 serial port cable to Serial Port 2 S2 position the ribbon cable so the colored stripe is on the side farthest away from the slot bracket Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 2 Turn OFF the power to your computer Unplug the power cord and remove the computer s cover Remove the slot bracket cover from an available PCI slot If you need the second serial port connect the 9 pin ribbon cable connector now and remove another slot bracket cover from an available PCI slot See Figure 1 on page 2 for more details Skip this step if you need only one serial port Carefully align the card to the selected PCI slot push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card Mount the second serial port and secure it with the slot bracket holding screw Skip this step if you need only one serial port Replace the computer cover and reconnect the power cord2. Driver Installation This section provides information on how to install the SIIG 2S1P Combo Value drivers Please make sure the board is installed before proceeding Windows 95 1 Atthe Update Device Driver Wizard click Next 2 Insert the driver CD and click Other Locations 3 Type in X 2S1P 95 click OK then click Finish Change X to match your CD ROM drive letter 4 From the Insert Disk window click OK When the Copying Files dialog box appears type in X 95 then click OK Change X to match your CD ROM drive letter 5 Restart Windows to complete the installation Windows 98 98SE 1 Atthe Add New Hardware Wizard click Next 2 Select Search for the best driver for your device Recommended then click Next 3 Select Specify a location uncheck the other boxes insert the driver CD type in X 2S1P 98 then click Next Change X to match your CD ROM drive letter 4 Click Next then click Finish 5 Restart Windows to complete the installation Windows ME 1 Atthe Add New Hardware Wizard check Specify the location of the driver Advanced then click Next 2 Check Specify a location uncheck the other box insert the driver CD type in X 2S1P ME then click Next Change X to match your CD ROM drive letter 3 Click Next then click Finish 4 Restart Windows to complete the installation Windows NT 4 0 1 From the desktop click Start then Run 2 Insert the driver CD type X 2S1P NT Set
3. P SIIG 2S1P Combo Value Quick Installation Guide Introducing the SIIG 2S1P Combo Value The SIG 251P Combo Value is a total solution for serial and parallel device connections It provides two 16550 UART serial ports which supports data transfer rates up to 115Kbps and one ECP EPP parallel port which supports data transfer rates up to 1 5 MB sec Features and Benefits Conforms to PCI v2 2 Plug and Play Can be installed in 32 64 bit 3 3V 5V PCI and PCI X slots e Fullsupport for DOS and Windows based software e PCI IRQ sharing feature reduces IRQ conflicts Serial interface e Two high speed 16550 UART serial ports 9 pin supports baud rate up to 115K Works with 56K modems PDAs and other high speed serial devices Parallel interface Compliant with IEEE 1284 1994 parallel port standard e Supports ECP EPP Bi directional PS2 and Standard Parallel Port SPP modes e Works with various types of parallel devices including printers removable drives scanners CD R RWs and more 04 0353B 1 System Requirements e Pentium or equivalent computer with an available PCI slot e DOS Windows 95 98 98SE ME NT 4 0 2000 XP 32 64 bit Server 2003 Vista 32 64 bit Package Contents e SIIG 2S1P Combo Value board e DB9 9 pin serial port cable for 2nd serial port e DriverCD e Quick installation guide Layout Serial Port 2 S2 g Serial Port 1 S1 Parallel Port
4. ck Manage then click Device Manger 2 Double click Multifunction adapters NetMos Controller should be listed 3 Double click Ports COM amp LPT two NetMos Serial Ports and one NetMoos Parallel Port should be listed Windows XP 64 bit Server 2003 1 Right click My Computer click Manage then click Device Manger 2 Double click Multifunction adapters MosChip Controller should be listed 3 Double click Ports COM amp LPT two MosChip Serial Ports and one MosChip Parallel Portshould be listed Windows Vista 1 Rightclick Computer click Manage click Continue then click Device Manger 2 Double click Multifunction adapters MosChip Controller should be listed 3 Double click Ports COM amp LPT two MosChip Serial Ports and one MosChip Parallel Portshould be listed Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could bejusta few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a 2 year manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please ret
5. e recommended click Continue 2 When prompted insert the driver CD and the driver will install automatically 3 At The software for this device has been successfully installed window click Close to complete the installation Note Driver installation may take several minutes to complete If your internet connection is enabled the driver may install automatically via Windows Update In this case steps 2 3 are not needed DOS 1 Insert the driver CD From the C gt prompt type copy X 2S1P dos and press Enter Change X to match your CD ROM drive letter 2 Type edit autoexec bat and press Enter 3 Add C nmdosin exe a at the bottom of the Autoexec bat file 4 Go to File save the changes and exit 5 Restart your system for the new setup to take effect Verify Windows Installation Windows 95 98 98SE ME 1 Right click My Computer click Properties click Device Manager 2 Double click Multi function adapters or NetMos MultiFunction NetMos PCI Controller should be listed 3 Double click Ports COM amp LPT two NetMos PCI Serial Ports and one NetMos PCI Parallel Port should be listed Windows NT 4 0 1 Click Start Settings Control Panel 2 Double click NetMos Multi I O Ports icon click Parallel Port tab a parallel port should be listed under Ports 3 Click Serial Port tab two serial ports should be listed under Ports Windows 2000 XP 1 Right click My Computer cli
6. he driver CD check Include this location in the search uncheck the other box type X 2S1P 64bit click Next Change X to match your CD ROM drive letter Click Continue Anyway then click Finish Repeat steps 1 4 three times to complete the installation Windows Server 2003 1 4 J At the Found New Hardware Wizard Eor Server 2003 Select Install from a list or specific location Advanced then click Next Eor Server 2003 SP1 or later Select No not this time click Next Select Install from a list or specific location Advanced then click Next Insert the driver CD check Include this location in the search uncheck the other box type in X 2S1P 2003 then click Next Change X to match your CD ROM drive letter At the Hardware Installation window click Continue Anyway then click Finish Repeat steps 1 3 three times Restart Windows to complete the installation 64 bit Windows Server 2003 1 Atthe Found New Hardware Wizard select No not this time click Next Select Install from a list or specific location Advanced click Next Insert the driver CD check Include this location in the search uncheck the other box type X 2S1P 64bit click Next Change X to match your CD ROM drive letter Click Continue Anyway then click Finish Repeat steps 1 4 three times to complete the installation Windows Vista 1 Atthe Found New Hardware window click Locate and install driver softwar
7. is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME SIG 2S1P Combo Value FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SHG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA SIIG 251P Combo Value isa trademark of SHG Inc SIIG and the SIG logo are registered trademarks of SHG Inc Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Pentium is a registered trademark of Intel Corporation Other names used in this publication are fo
8. r identification only and may be trademarks of their respective companies November 2007 Copyright 2007 by SIIG Inc All rights reserved
9. up_Combo exe then click OK Change X to match your CD ROM drive letter 3 At the Welcome window click Continue 4 Atthe Multi IO Drivers Setup window click Next 5 Select Yes and click Finish to restart NT to complete the installation Windows 2000 1 At the Found New Hardware Wizard click Next Select Search for a suitable driver for my device Recommended then click Next 3 Select Specify the location uncheck the other boxes then click Next 4 Insert the driver CD type in X 2S1P 2000 then click OK Change X to match your CD ROM drive letter 5 Click Next then click Finish to complete the installation Windows XP 1 4 J At the Found New Hardware Wizard Eor XP SP1 or earlier Select Install from a list or specific location Advanced then click Next For XP SP2 or later Select No not this time click Next Select Install from a list or specific location Advanced then click Next Insert the driver CD check Include this location in the search uncheck the other box type in X 2S1P XP then click Next Change X to match your CD ROM drive letter At the Hardware Installation window click Continue Anyway then click Finish Repeat steps 1 3 three times Restart Windows to complete the installation 64 bit Windows XP 1 Atthe Found New Hardware Wizard select No not this time click Next Select Install from a list or specific location Advanced click Next Insert t
10. urn the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number will be issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in1985 SHG Inc isa leading computer upgrade manufacturer of 1 Oconnectivity products including PCI amp ISA serialand parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG
Download Pdf Manuals
Related Search