Axis Q8108-R
Contents
1. L AXIS 08108 R User s Guide Page 13 AXIS NVR Manager 1 Connect to the NVR directly via a network cable or through the network and make sure that power has been applied Start AXIS NVR Manager AXIS NVR Manager will automatically discover all NVRs that are in the same network Note that the NVR startup takes more than a minute and must be completed before it can be discovered AXIS NVR Manager DER File Tools Options Help Fkk FEAR Ot S25 Server Address Status Serial Number Model Firmware P busi 10 96 127 231 OK HwW0555023 AXIS Q8108 R 1 00 00 bus 2 10 96 127 221 OK HW0533021 AXIS Q8108 R 1 00 2 bus 3 10 96 127 230 OK Hw0529023 AXIS Q8108 R 1 00 00 P bus 4 10 96 127 229 OK H AXIS Q8108 R 1 00 2 Set the password The default user name is Administrator and password is password It is strongly recommended that the Administrator password be changed at once to a strong password containing both upper and lower case letters and numbers 1 Select the NVR in the AXIS NVR Manager window 2 Go to Tools gt Set Master Credentials 3 Enter a strong password Network configuration Network settings can be assigned either automatically or manually Go to Tools gt Network Configuration To access the NVR from behind a router UPnP must be enabled in AXIS NVR Manager Check Enable UPnP under Network Configuration When enabling UPnP the NVR needs to be in the subnet as your computer Make sure that th2. method 514 5 EN 55022 EN 55024 EN 61000 4 2 ISO 11452 2 EN 61000 4 3 ISO 11452 2 EN 61000 4 4 EN 61000 4 5 EN 61000 4 11 ISO 7637 2 EN50121 3 2 FCC part 15 subpart B class B Project customization WLAN 802 11b g GSM UMTS HSDPA GPS Accelerometer User s Guide AXIS 08108 R Axis Communications AB 2010 Ver 1 0 Printed August 2010 Part No 39382
3. 6W Network connector 1 Gbit port for external network connection Power connector 3 pin terminal block Use a fused power supply 12V DC 10A or 24V DC 5 A 2 USB 2 0 ports To be used with any peripheral USB device Max load 500mA I O connector 2 digital output ports and 8 digital input ports 2 4 6 8 10 12 L AXIS 08108 R User s Guide Page 7 Pin assignment I O connector Pin Function Notes Specifications number 1 Output 1 Open collector NPN transistor with the emitter Max load 500mA 2 Output 2 connected to ground when activated Outputs are reserved for developer use 3 Input 1 Inactive for voltages less than 1V Max input 30V 4 Input 2 Active for voltages more than 3V 5 input 3 Only one input can be programmed via AXIS NVR manager see Power Configuration on page 13 6 Input 4 7 Input 5 8 Input 6 9 Input 7 10 Input 8 11 5V DC Can be used to power auxiliary equipment Max load 250mA Power Note This pin can only be used as power out 12 GND Ground LED indicators LED Color Indication Network Amber Link established Green Steady for connection to 100 Mbit s network Unlit For connection to 1Gbit s network Power Green Power supplied normal operation Green and Battery powered Amber Unlit Power off PoE Link Green Steady Power is being s
4. 8 R User s Guide Page 9 E Connect the cables 1 Gbit network port 8 x PoE network connectors i 1 0 connector Power connector T PAPPP nial f ANE U U U U L 2 USB 2 0 ports Install up to 8 Axis network cameras according to their Installation Guides 2 Connect cameras to AXIS 8108 R via RJ 45 PoE connectors which will provide both power and network connection to each camera 3 Optionally connect external input output devices 4 Connect the supplied power cable to the power block HSITSNA4 L Page 10 AXIS 08108 R User s Guide Mounting Hard Disk AXIS 08108 R supports the use of up to 2 separate hard disk Follow these instructions and consult manufacturer s recommendations to mount or change hard disk Remove the back cover Power off the AXIS 08108 R see Start up and shut down on page 11 and LED indicators on page 7 Insert hard disks into adapter kit It s possible to use one 3 5 or up to two 2 5 hard disks Insert adapter kit with hard disks into the bracket in the lid Attach the SATA connectors Power on the device NO Pw Replace back cover and tighten screws L AXIS 08108 R User s Guide Start up and shut down The AXIS 08108 R starts up automatically when power is supplied See AXIS NVR Manager on page 13 for more options The AXIS 08108 R automatically does a controlled shut down after one minute when the power is shut off Internal pow
5. User s Guide AXIS 08108 R Network Video Recorder AXISA COMMUNICATIONS HSTION2 About this Document This document includes instructions for installing the AXIS 08108 R Network Video Recorder Legal Considerations Video and audio surveillance can be prohibited by laws that vary from country to country Check the laws in your local region before using this product for surveillance purposes Electromagnetic Compatibility EMC This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a different circuit to the receiver Consult your dealer or an experienced radio TV technician for help Shielded STP network cables must be used with this unit to ensure compliance with EMC standards USA This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart B of Part 15 o
6. actory default settings will not affect AXIS Camera Station settings or recordings HSITSNA4 L Page 12 AXIS 08108 R User s Guide Set up your computer This section will help you install AXIS NVR Manager and AXIS Camera Station Client and configure it for your Axis NVRs and Axis Network Cameras A brief introduction to the functionality of the software is covered here For more information see the context sensitive help files or for AXIS Camera Station see the User s Manual available at www axis com AXIS NVR Manager is for discovery configuration and firmware upgrade of AXIS 08108 R Go to www axis com to download AXIS NVR Manager and follow the install wizard s instructions Make sure you have full administrator rights on the computer you install on AXIS Camera Station Client is for monitoring recording playback and event management of Axis network cameras Launch AXIS Camera Station Client from AXIS NVR Manager and follow the install wizard s instructions or download from www axis com Minimum recommended requirements for AXIS NVR Manager and AXIS Camera Station Client PC minimum requirements e Memory 1 GB RAM Software Windows XP SP2 Server 2003 SP2 Vista Windows 7 For other operating sys tems see www axis com techsup Microsoft NET 3 5 included in installation package e Support for DirectX 9 0c For individual PC requirements for AXIS Camera Station Client refer to the AXIS Camera Station User s Manual
7. all not be liable nor responsible for incidental or consequential damages in connection with the furnishing performance or use of this material RoHS This product complies with both the European N RoHS directive 2002 95 EC and the Chinese O RoHS regulations ACPEIP WEEE Directive The European Union has enacted a Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE Directive This directive is applicable in the European Union member states The WEEE marking on this product see right or its documentation indicates that the product must not be disposed of together with household waste To prevent possible harm to human health and or the environment the product must be disposed of in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the product supplier or the local authority responsible for waste disposal in your area Business users should contact the product supplier for information on how to dispose of this product correctly This product should not be mixed with other commercial waste Support Should you require any technical assistance please contact your Axis reseller If your questions cannot be answered immediately your reseller will forward your queries through the appropriate channels to ensure a rapid response If you are connected to the Internet you can e download user documentation e find an
8. e router is UPnP capable and has UPnP enabled Caution For security reasons enable UPnP in order to access the NVR via AXIS NVR Manager or AXIS Camera Station only when the NVR is behind a router that requires NAT traversal Power Configuration To configure how the NVR powers on go Tools gt Power Configuration The AXIS 08108 R can be configured to power on automatically when external power is available manually with the internal power button or when an external button is wired to an input port Note If power configuration is done incorrectly you might not be able to start the NVR To remedy this situation go to Resetting to the factory default settings on page 11 and follow the instructions HSITSNA4 Page 14 AXIS 08108 R User s Guide AXIS Camera Station AXIS Camera Station Client is for monitoring recording playback and event management Connect AXIS Camera Station Client From AXIS NVR Manager select an NVR device and click the Launch AXIS Camera Station Client icon or start AXIS Camera Station Client from your computer and use the NVR s network address in the logon dialog Notes If the correct version of AXIS Camera Station Client has not been previously installed on the computer running AXIS NVR Manager a prompt will appear to perform an installation e Prior versions of AXIS Camera Station Client and AXIS Camera Station Server need to be removed from the computer before installing this version D
9. er button aye ss ADAC Internal power button Use this button to manually start up or shut down the AXIS Q8108 R When pushed briefly the NVR will power down in a controlled manner which will take 15 30 seconds If the button is held down for more than 3 seconds the NVR will hard power down This is useful if for some reason the NVR becomes unresponsive The internal power button is also used for resetting the NVR to factory default settings see Resetting to the factor default settings Battery backup function The AXIS 08108 R has an Uninterruptable Power Supply UPS designed for short power shortages For periods more than 1 minute the UPS will provide enough power to the AXIS 08108 R for a controlled shut down A controlled shutdown may not occur if the battery temperature is outside of charging range 0 45 C 32 113 F Resetting to the factory default settings This will reset parameters to the factory default settings including the password 1 Disconnect power from the NVR and remove back cover 2 Make sure all indicator LEDs are off this could take a few moments 3 Press and hold the Internal power button and reconnect power 4 Release the Internal power button when the power LED is lit These settings will be reset e Network configuration is set to factory default DHCP and UPnP off e Administrator password is set to password e Power Configuration is set to Automatic Resetting the NVR to f
10. f FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his her own expense will be required to take whatever measures may be required to correct the interference Europe C This digital equipment fulfills the requirements for radiated emission according to limit B of EN55022 and the requirements for immunity according to EN55024 residential and commercial industry Equipment Modifications This equipment must be installed and used in strict accordance with the instructions given in the user documentation This equipment contains no user serviceable components Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals Liability Every care has been taken in the preparation of this document Please inform your local Axis office of any inaccuracies or omissions Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and documentation without prior notice Axis Communications AB makes no warranty of any kind with regard to the material contained within this document including but not limited to the implied warranties of merchantability and fitness for a particular purpose Axis Communications AB sh
11. l Atom Z5 series CPU RAM 1GB SODIMM DDR2 System disk Compact Flash PATA drive 4GB Operating system Windows Embedded Standard 2009 Battery backup Controlled shutdown 1 minute after power loss Network Security Password protection user access log NTP NTP server included Software Video Management AXIS Camera Station 8 channel license included Software For more information see www axis com products cam_station_software Application Open API for software integration Programming Interface Video compression H 264 MPEG 4 Part 10 AVC MPEG 4 Part 2 Motion JPEG Audio compression AAC G 711 G 726 Resolutions Supports connected Axis video product resolutions Recording frame rate Supports connected Axis video product frame rates Maximum total recording bit rate 70 Mb s General Casing Rugged IP43 rated aluminum casing Input voltage 12 or 24V DC Max power 84 W PoE output 8 PoE class 1 or 1 PoE class 0 4 PoE class 1 or 2 PoE class 0 Connectors 2x high speed USB ports 1x Gbit port for external connection 8 RJ 45 10BASE T 100BASE TX PoE 2 digital output ports and 8 digital input ports 2 SATA connectors Operating 10 to 50 C 14 122 F Temperatures Weights 3 7 kg 8 14 Ib HSIN L Pane 16 AXIS 08108 R User s Guide Function Item Specification group Approvals EU directive 2002 96 EC MIL STD 810F Method 516 5 Procedure MIL STD 810F
12. m 7 g come E N Leer E s L ae z G Je 9 7 URRA s E 2 Z ale PAARE zE 1 5 2 E a E N 5 le N H S 193 6 mm 7 6 z 211mm 8 3 L AXIS 08108 R User s Guide Page 5 E Back SATA power cable adapter PoE and Link LED indicators Internal power button Hale do PEARS Power LED indicators SATA connectors Battery Front 1 Gbit network port Network LED indicators Ss 0 connector NV 8 x PoE network connectors 2 USB 2 0 ports Power connector HSITSNA L Page 6 AXIS 08108 R User s Guide Unit connectors 8 PoE network connectors RJ 45 Ethernet connectors Provides power to up to 8 network cameras that are PoE enabled Class 1 The PoE ports are divided into a left and right group of four A maximum load of 16W is allowed per group For example a PoE class 0 can be connected in the left group and up to 4 PoE class 1 can be connected in the right group If a PoE class 0 is connected the other ports in the group must not be used See illustration below and Technical specifications on page 15 Possible combinations yey r2 E FeAl 4 PoE Class 1 4 PoE Class 1 4 PoE Class 1 1 PoE Class 0 rs o a sy 1 PoE Classo 4 PoE Class 1 Left group Right group Total 8 5 5 1 PoE Class 0 1 PoE Class 0 2 Left group Right group 4 PoE class 1 4 PoE class 1 1 PoE class 0 1 PoE class O Max load 16W Max load 1
13. o not continue with the installation if the removal of prior versions is not your intent To log onto the NVR enter the administrator user name and password you set up in NVR Manager see Set the password on page 13 Configure AXIS Camera Station For easy navigation AXIS Camera Station is divided into workspaces Live view Recordings Logs and Configuration e Live view Provides a single interface to organize and monitor AXIS network cameras and video encoders on your network e Recordings Search playback and export recordings from one or many cameras in a desired time interval with timeline visualization e Logs Alarm event and audit logs for an instant overview of the system e Configuration has a collection of all the important links to add cameras set up recording settings user permissions event configuration and more When AXIS Camera Station is started for the first time it automatically adds Axis cameras and video encoders it finds on your network If there are more cameras on your network than you have a license for go to Configuration gt Add Edit Cameras Note To use the NVR as an NIP server for the added cameras use the NVR s IP address For more information see the context sensitive help in AXIS Camera Station or the User s Manual L AXIS 08108 R User s Guide Page 15 Technical Specifications Function Item Specification group Model AXIS 08108 R System Processor 1 1GHz Inte
14. swers to resolved problems in the FAQ database Search by product category or phrases e report problems to Axis support by logging in to your private support area L AXIS 08108 R User s Guide Page 3 AXIS Q8108 R User s Guide This user s guide provides instructions for installing the AXIS Q8108 R Network Video Recorder Hardware overview page 4 Unit connectors page 5 Install the hardware page 8 Connect the cables page 9 Mounting Hard Disk page 10 Set up your computer page 12 Technical Specifications page 15 Important The network video recorder should be installed by a trained professional Please observe relevant national and local regulations for the installation Package contents Item Models variants notes Network Video Recorder AXIS 08108 R Printed materials AXIS 08108 R User s Guide this document Included accessories Power cable with terminal block Cable shelf Not included accessory Power supply Cable sealing for IP65 rating HSITSNA4 Page 4 AXIS 08108 R User s Guide Hardware overview a Back cover Front panel Cable shelf Screws to clamp cables Dimensions L J Ve 178 m
15. upplied to the camera Flash slowly Short circuit 2 flash sequence Error in PoE connection 5 flash sequence Connected units exceed the max load 6 flash sequence Connected units in the left or right group exceed the max load Amber Link established HSNI L Page 8 AXIS 08108 R User s Guide Install the hardware Before you begin There are a few considerations before installing the AXIS 08108 R e The AXIS 08108 R casing is designed to mount directly on any surface using a minimum of 4 screws appropriate for the surface type e The operating temperature range is dependent on the Hard Disk e Install in an open area allowing for 10mm of space on all sides for cooling and ventilation e Ensure there is proper fuse protection 12V DC 10A or 24V DC 5 A 1 Use at least 4 screws appropriate for the surface The AXIS 08108 R is designed to install in any position but if it is to be installed in a vertical position the cable shelf should be pointing up for optimal heat dissipation Cables should point up v installing in the verical ax 9 m 8 ax Thread the cables through cable shelf For an IP65 rating use Cable Sealing not included Connect all appropriate cables See Connect the cables on page 9 Attach front cable shelf to AXIS 08108 R with the four provided screws Tighten shelf to clamp cables This prevents connector damage during operation ao E L AXIS 0810
Download Pdf Manuals
Related Search