Miele K 9757 ID-1
Contents
1. Fan for dynamic cooling Bottle rack 3 Adjustable shelves 9 PerfectFresh zone dry compartment 9 PerfectFresh zone humidity controlled compartments or compartment depending on model Butter and cheese compartment Egg tray Condiment tray Interior lighting Universal container Condensate channel and drain hole Bottle shelf 42 Bottle divider 49 Regulator to set the humidity level in the humidity controlled compartments or compartment depending on model Depending on model Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please ensure that they are recycled Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre o2. Replacement fuses should be ASTA approved to BS 1362 and have the correct rating Replacement fuses and fuse covers may be purchased from your local electrical supplier WARNING THIS APPLIANCE MUST BE EARTHED 33 Installation This appliance must be built in otherwise it could tip up Location This appliance should be installed in a dry well ventilated room It should not be installed where it is exposed to direct sunlight or directly adjacentto a heat producing appliance such as an oven or a radiator The room temperature should not go above or below the climate range for which the appliance is designed The higher the ambient temperature of the room the more energy the appliance requires to operate Side by side To avoid a build up of condensation and resultant damage refrigerators with PerfectFresh zones should not generally be installed side by side next to other refrigeration appliances The K 9557 iD 1 and K 9757 iD 1 refrigerators however have foamed in side wall heaters enabling them to be installed side by side with certain freezers Your dealer will be able to advise you on which models are suitable m The refrigerator must be installed to the right of the freezer when viewed from the front The side wall heating in the right hand wall is insulated to prevent the build up of condensation between the two appliances 34 Important tropical humid environments During periods of hi
3. The optimum storage temperature for fresh food which is not sensitive to the cold is 0 3 C This is the temperature range which is automatically maintained in the PerfectFresh zone Food can be stored there at this temperature without loss of freshness for considerably longer than in a standard refrigerator as the deterioration process is decelerated at this temperature Humidity level The closer the storage humidity is to the humidity content of the food the crisper and fresher the food remains over a longer period as the water content of the food is largely retained What are the advantages of the PerfectFresh zone As food remains fresh for up to three times as long the advantages for you are fresher tastier food greater convenience due to practical storage and greater savings due to quality preservation Storing food in the dry and humidity controlled compartments The PerfectFresh zone is divided into two areas the dry compartment and the humidity controlled compartment The dry compartment The dry compartment has a relatively low humidity level that is approx the same as that in the refrigerator So the main advantage of the dry compartment is the low temperature of 0 C rather than the humidity The dry compartment is ideal for storing particularly sensitive foods such as fresh fish shellfish meat poultry sausages dairy products and salads Please note tha
4. puncturing the refrigerant channels in the evaporator bending any pipework scratching the surface coating Splashes of refrigerant can damage the eyes The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions How to save energy Normal energy consumption Increased energy consumption Installation site In a ventilated room In an enclosed unventilated room Protected from direct sunlight In direct sunlight Not situated near to a heat source radiator oven Situated near to a heat source radiator oven Where the ideal ambient room temperature is approx 20 C Where there is a high ambient room temperature Temperature setting with a thermostat which is approximate set in stages With a medium setting of 2 to 3 With a high setting the lower the temperature in the compartment the higher the energy consumption Temperature setting with a thermostat which is exact to the degree digital display Cellar section 8 to 12 C Refrigerator section 4 to 5 C On appliances with winter setting please make sure that the winter PerfectFresh zone just above 0 C setting is switched off when the Freezer section 18 C ambient temperature is warmer than 16 C Wine storage section 10 to 12 C Use Only open the doors when Frequent op
5. cake mixtures pizza or quiche dough soft cheese and other dairy products pre packed vegetables and other fresh food with a label stating it should be kept at a temperature of approx 4 C Do not store explosive materials in the appliance or any products containing propellants e g spray cans Danger of explosion If storing alcohol with a high percentage proof make sure it is tightly closed and store upright Do not store cooking oil in the refrigerator door Traces of oil can cause stress cracks to occur in the plastic components in the door Food must not touch the back wall of the refrigerator as it may freeze to the back wall To allow air to circulate efficiently do not pack food too closely together in the refrigerator Do not cover the fan in the rear wall of the refrigerator as this is essential for keeping the appliance cool Using the refrigerator efficiently Food which should not be stored in a refrigerator Not all food is suitable for refrigeration This includes Fruit and vegetables which are sensitive to cold such as bananas avocado papaya passion fruit aubergines peppers tomatoes and cucumbers Fruit which is not yet ripe Potatoes Some hard cheeses e g Parmesan When shopping for food The freshness of food when first placed in the appliance is an important factor in determining how long it stays fresh and how long it can be kept in the
6. conditioner gives long lasting protection and helps to prevent resoiling m Clean the inside of the appliance and the accessories with warm water and a little washing up liquid and then dry with a soft cloth Important To ensure the correct functioning of the appliance let it stand for between 1 and 2 hours after transporting it to its final location before connecting it to the mains 12 Switching on CO Ss N m Press the On Off button The temperature display lights up the appliance starts cooling and the interior light will come on when the door is opened To enable the temperature to get sufficiently cold inside the appliance allow the appliance to run for a few hours before placing food in it Switching off m Press the On Off button until the temperature display goes out The cooling system is switched off If this does not happen the safety lock is still activated Safety lock The safety lock can be activated to prevent the appliance being switched off inadvertently Switching on and off Activating or de activating the safety lock S m Press and hold the Super cool button pressed in for approx 5 seconds The Super cool indicator light flashes and ac flashes in the temperature display m Press the Super cool button again c will light up in the display Ce Le m You can now choose between and 7 by pressing the temperature selector buttons G the
7. door using hexagonal screw m Whilst counterholding the adjusting Make sure the two metal edges bolts with a screwdriver tighten are aligned Symbol nuts 8 on the appliance door m Drill fixing holes in the furniture m Cover strip 49 must be completely door and screw in 4 x 14 mm screws hidden in the niche and must not protrude On large or divided doors attach a m Tighten all screws again second pair of fixing brackets in the handle region of the door Use the pre drilled holes in the appliance door Align depth Z on the furniture door Loosen screws at the top of the appliance door and loosen the hexagon headed screw at the bottom of the fixing bracket By moving the furniture doors create a gap of 2 mm between the furniture doors and the front edge of the niche 48 Building in the appliance m Replace all the covers To make sure the appliance is correctly fitted The door must close properly The door must not touch the furniture carcase The seal at the top edge of the handle side must fit properly To double check place a torch in the appliance and close the doors Turn the lights out in the room If you can see any light shining out from the sides double check the installation 49 50 51 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer C
8. on m Check that the fuse is not defective and that the mains fuse has not tripped If it has contact the Miele Service Department the temperature in the refrigerator is too low m Select a warmer temperature m The Super cool function is still switched on Super cool only switches itself off after 6 hours the appliance is switching in too frequently and for too long m Check whether ventilation gaps in the plinth and in the housing unit at the top have been covered over or become too dusty m The door has been opened too frequently or large quantities of fresh food have been put in at once m Check that the door has been closed properly bars flash in the temperature display Check the temperature display about 6 hours after switching on the appliance The display will not show a temperature until the temperature in the appliance has reached a certain level the following messages show in the temperature display FO to F5 There is a fault Call the Service Department you cannot switch the appliance off The safety lock has been activated the alarm sounds Has the appliance door been open for longer than 60 seconds m Close the door 29 Problem solving guide the interior light is not working Has the refrigerator door been left open for too long The lighting switches itself off automatically after approx 15 minutes If it also does not come on whe
9. plinth in the housing unit The cross section of the air inlet and outlet must be at least 200 cm to ensure that air can circulate without hindrance Otherwise the appliance has to work harder resulting in an increase in electricity consumption The air inlet and outlet must not be covered or blocked in any way They should be dusted on a regular basis Before installation m Before installation remove the cover strip sealing strip and other accessories from inside the appliance and from the external rear wall of the appliance m Onno account should the spacers be removed from the back of the appliance These ensure the gap required between the back of the appliance and the wall is maintained m Remove any cable clips from the rear of the appliance m Check that all parts at the back of the appliance are unhindered Carefully remove any hindrance Does your old appliance have a different hinging mechanism If your old appliance had a different type of hinging the furniture door can still be used Remove the old hinges from the housing unit They are no longer required because the furniture door is now fitted to the appliance door All the necessary parts are supplied or can be ordered from the Miele Spare Parts Department 35 Installation Stainless steel front depending on model The old door can be replaced by a stainless st
10. Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 4209 K 9457 iD 1 K 9557 iD 1 K 9757 iD 1 ce M Nr 07 471 431 03
11. a service call E Cloth m A microfibre E Cloth is available from the Miele Spare Parts Department which is suitable for cleaning surfaces such as stainless steel glass plastic and chrome without the use of chemicals It can be washed 300 times Before cleaning m Switch the appliance off switch off at the socket and remove the plug m Take any food out of the appliance and store it in a cool place m Take out any removable parts e g shelves for cleaning m The serving trays and containers in the door can be removed from their stainless steel frames for cleaning Cleaning the interior and accessories Use warm water with a little washing up liquid Accessories and shelves should all be hand washed only The butter dish is however dishwasher safe m Clean the appliance at least once a month m Clean the condensate channel and drain hole frequently so that condensate can drain away unhindered Use a straw or similar to clear the drain if necessary m After cleaning wipe the interior and accessories with a damp cloth and dry with a soft cloth Leave the door open to air the appliance for a short while 27 Cleaning and care m Clean stainless steel surfaces with a suitable non abrasive stainless steel cleaning agent following the manufacturer s instructions on the packaging m To help prevent re soiling a conditioning agent for stainless steel should always be used after cleaning
12. calling 08706 080028 or registering online at www miele co uk 32 Electrical connection Electrical connection U K All electrical work should be carried out by a suitably gualified and competent person in strict accordance with current local and national safety regulations BS 7671 in the UK The appliance is supplied with a mains cable and moulded plug ready for connection to an a c single phase 220 240 V 50 Hz supply Please ensure that the connection data quoted on the data plate match the household mains supply Connection should be made via a suitable switched socket which is easily accessible For extra safety it is advisable to install a suitable residual current device RCD Do not connect the appliance to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating The appliance must not be connected to an inverter and must not be used with a plug adapter as these can cause damage to the appliance s electronic unit Non rewireable plugs BS 1363 The fuse cover must be re fitted when changing the fuse and if the fuse cover is lost the plug must not be used until a suitable replacement is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words in the base of the plug as applicable to the design of the plug fitted
13. do about easily rectify them Rattling vibrating The appliance is uneven Realign the appliance using a spirit level by raising or lowering the screw feet underneath the appliance The appliance is touching another appliance or piece of furniture Move it away Drawers baskets or shelves are unstable or sticking Check all removable items and refit them correctly Are any bottles or containers unstable or knocking against each other Separate them The transport cable clips are hanging loose at the back of the appliance Remove the clips 31 After Sales Guarantee In the event of a fault which you cannot correct yourself or if the appliance is under guarantee please contact your Miele Dealer or Miele see back cover for contact details When contacting your Dealer or Miele please quote the model and serial number of your appliance This information is given on the data plate inside your appliance Please note that telephone calls may be monitored and recorded for training purposes N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions Guarantee For information on the appliance guarantee specific to your country please contact Miele See back cover for contact details In the U K your appliance is guaranteed for 2 years from the date of delivery However you must activate your cover by
14. lower edge X of the fitting aids must be at the same height as the upper edge of the furniture door being fitted see A on the diagram m Undo nuts and take fixing bracket off together with the fitting aids Building in the appliance m Using a pencil lightly mark a line down the centre of the inside of the furniture door m Hang fixing bracket with the fitting aids onto the inside of the furniture door Align the fixing bracket centrally m Attach the fixing bracket securely using at least 6 short chipboard screws 4 x 14 mm On cassette doors only use 4 screws on the edges m Pull the fitting aids upwards to remove them m Turn them around and fit them into the middle slots on fixing bracket for safe keeping m Hang the furniture door onto adjusting bolts m Loosely attach nuts on the adjusting bolts m Close the door and check the distance between the door and neighbouring furniture doors m Align to match neigbouring doors if necessary Side adjustments X are made by sliding the furniture door and height adjustments Y by turning adjusting bolts 8 with a screwdriver m Tighten nuts 47 Building in the appliance Securing the appliance door to the furniture door m Close the door and align it with neighbouring furniture doors m Screw fixing bracket into the pre drilled holes in the appliance
15. refrigerator Time out of the refrigerator e g during transportation should be kept to a minimum For example do not allow food to stay in a hot car for too long Once food has started to deteriorate this process cannot be reversed As little as two hours outside the refrigerator can cause food to start deteriorating 20 Storing food correctly Food should generally be stored covered or packaged in the refrigerator there are some exceptions to this rule in the PerfectFresh zone see below This will prevent food smells from affecting other foods food from drying out and also any cross contamination of bacteria The growth of bacteria such as salmonella can be avoided by setting the correct temperature and maintaining good standards of hygiene Unpacked meat and vegetables Unpackaged meat and vegetables should be stored separately To avoid any microbiological cross contamination these foods may only be stored together if they are wrapped Using the PerfectFresh zone For every type of food there are ideal storage conditions to ensure it stays fresh as long as possible retaining both flavour and vitamins The important factors for this are the storage temperature and the humidity The correct combination of temperature and humidity is a unigue feature of the PerfectFresh zone Food can be stored for up to three times longer in the PerfectFresh zone than in a standard refrigerator Storage temperature
16. Follow the manufacturer s instructions on the label Ventilation gaps m The ventilation gaps should be cleaned on a regular basis with a brush or vacuum cleaner A build up of dust will increase the energy consumption of the appliance Door seal Do not use any oils or grease on the door seal as these will cause the seal to deteriorate and become porous over time The door seal should be cleaned regularly with clean water and then wiped dry with a soft cloth 28 After cleaning m Replace all shelves and accessories in the appliance m Insert the plug in the socket and switch the appliance back on m Switch on the Super cool function for a while so that the appliance can cool down quickly m Place food back in the appliance and close the door Problem solving guide Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Ensure that current is not supplied to the appliance until after maintenance or repair work has been carried out What to do if the appliance does not get cool m Check whether the appliance has been switched on The temperature display must be lit up m Check that the plug is correctly inserted in the socket and switched
17. and the front edge of the housing unit side wall the door may not shut properly This could lead to a build up of ice and condensation and also cause operational faults m Align the appliance height on both sides by altering the adjustable feet using the spanner supplied Securing the appliance in the niche m Press the appliance against the housing unit wall on the hinge side m To fix the appliance to the housing unit at the top and bottom screw the long 4 x 20 mm chip board screws into the hinges at the top and bottom 45 Building in the appliance m Loosen screws on the top and bottom fixing brackets m Press fixing bracket against the side wall and tighten screws m Attach fixing bracket to the housing unit side wall with screws Drill holes in the housing unit side walls if necessary m Break off the protruding end of top cover turn the cover around and fit it on top fixing bracket m Fit oblong cover onto top fixing bracket 46 m Break off the protruding end of bottom cover It is no longer required m Fit angled cover onto bottom fixing bracket m Close the appliance door Fitting a furniture door m A gap of 8 mm must be set between the appliance door and the central fixing bracket m Push fitting aids up to the height of the furniture door the
18. areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Correct use gt Never store explosive materials in the appliance or any products containing propellants e g spray cans Thermostats switching on may produce sparks which could present a fire hazard Flammable compounds could explode gt Do not operate any electrical equipment e g an electric ice cream maker inside the appliance Danger of sparking and explosion gt If storing alcohol with a high percentage proof make sure it is tightly closed and stored upright Danger of explosion gt Observe the use by dates given on food to avoid the risk of food poisoning Storage times will depend on several factors including the freshness and quality of the food as well as the temperature at which it is stored Follow the instructions given on the food manufacturer s packaging on storage conditions required Warning and Safety instructions gt Do not use sharp edged objects to remove frost and ice separate food which has become frozen They will damage the evaporator causing irreversible damage to the appliance gt Do not use defrosting sprays or de icers as they might contain substances which could damage the p
19. d the following tools across slotted screwdriver ascrewdriver a selection of Torx screwdrivers a spanner Appliance door m Open the appliance door m Remove covers and with a screwdriver m Loosen fixing screws at the top and the bottom slightly m Slide the door outwards and lift it off m Unscrew the fixing screws completely and loosely screw them in at the top and bottom on the opposite side of the appliance If you have put locking pins into the hinges to stop the door opening too far m Remove the locking pins from the top of the hinges To remove the soft close mechanism m Place the door with the outer side downwards on a stable surface m Using a screwdriver carefully push tension spring outwards Warning The soft close mechanism snaps shut when dismantled Danger of injury 39 Changing the door hinging m Unscrew mounting and pull soft close mechanism 3 downwards to remove it m Undo ball joint using a spanner and remove it m Stand the appliance door up and loosen the hinges at the front the hinges remain open m Remove screws and use the stoppers supplied to plug the empty holes Do not close up the hinges Danger of inury 40 m Replace the hinges in their diagonally opposite corners m Use a powered screwdriver to secure the hinges screws are self tapping To secure the soft c
20. eee Viele Operating and installation instructions Refrigerator with PerfectFresh zone and dynamic cooling K 9457 iD 1 K 9557 iD 1 K 9757 iD 1 To avoid the risk of accidents or en GB HK damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 471 431 Contents Guidetotheappliance 4 Caringfortheenvironment 6 Warning and Safety instructions 7 Howtosaveenergy 11 Switchingonandoft 12 Before using for thefirsttime 12 DAISY JOCK sun Wa oh asad Kaa Br RUA Are ee a Pea re 12 Switching off for longer periods oftime 13 Thecorrecttemperature 14 in the refrigerator and the PerfectFresh zone 14 Dynamic COOMING WAA 24 een hie ie ent 14 Setting the temperature in the refrigerator 14 Temperature III ae einer 15 Setting the temperature in the PerfectFresh zone 15 Temperature display auusuu san aa Pode nn ae han NI 16 Temperature display brightness 16 WI ee en ae eae eee ie 17 Switching
21. eel front if required This is available from your dealer or the Miele Spare Parts Department 36 Building in dimensions 5 gt 200 cm Niche height mm A K 9457 iD 1 1220 1236 K 9557 iD 1 1397 1413 K 9757 iD 1 1772 1788 37 Adjusting the door hinges The door hinges are set ex works to enable the door to be opened wide However ifthe opening angle of the door needs to be limited for any reason the hinge can be adjusted to accommodate this For example ifthe appliance door hits an adjacent wall when opened the opening angle can be limited to 90 m Place the locking pins supplied for limiting the door opening into the hinges from above The door opening angle is now limited to 90 38 If you would like the appliance door to be cushioned so that it opens more softly the spring tension on the appliance door can be adjusted To do this use the allen key supplied to adjust the door hinges To reduce the opening angle m Turn the allen key clockwise This tightens the hinges and makes it harder to open the door wide To open the door fully m Turn the allen key anticlockwise Changing the door hinging Before building the appliance in you will need to decide on which side the door is to be hinged If left hand door hinging is reguired follow the instructions below To change the door hinging you will nee
22. ening of the doors for necessary and for as short atime long periods will cause a loss of as possible coldness Store food in an organised way If food is not stored in an organised way searching for an item will mean the door is open for longer Allow hot food and drinks to cool Placing hot food in the appliance down before placing them in the will cause the compressor to run appliance for along time as the appliance will have to work harder to lower the temperature Store food covered or packaged The evaporation or condensation of liquids will cause a loss of coldness in the refrigerator Place frozen food in the refrigerator to defrost Do not over fill the appliance to allow air to circulate Defrosting Defrost the freezer compartment A layer of ice hinders the cold when a layer of ice 0 5 cm thick has built up from reaching the frozen food and causes an increase in energy consumption 11 Switching on and off Before using for the first time The stainless steel trim to the interior shelves and the door shelves has a layer of protective foil to prevent scratching during transportation m Do not remove this foil until the appliance has been built in m Treat the stainless steel surfaces with a proprietary stainless steel conditioner immediately after removing the foil available from the Miele Spare Parts Department or via the internet on www miele co uk Important A stainless steel
23. g electric shock gt If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger Warning and Safety instructions gt Safe operation of the appliance is only assured if it has been installed and connected in accordance with these operating and installation instructions gt This equipment may only be used in mobile installations such as ships caravans aircraft etc if a risk assessment of the installation has been carried out by a suitably qualified engineer gt gt Installation work maintenance and repairs may only be carried out by suitably qualified and competent persons in accordance with national and local safety regulations Repairs and other work by unqualified persons could be dangerous and the manufacturer will not be held liable Ensure current is not supplied to the appliance until after maintenance or repair work has been carried out gt The appliance is only completely isolated from the electricity supply when it has been switched off at the wall socket and the plug has been withdrawn the mains fuse is withdrawn or the screw out fuse is removed in countries where this is applicable gt Do not connect the appliance to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the machine e g danger of overheating gt In countries where there are
24. gh humidity some condensation may appear on outside surfaces of cooling appliances This condensation will disappear when humidity levels drop For prevention it is advisable to install the appliance with sufficient ventilation in a dry and or an air conditioned room Please ensure that doors are closing and sealing properly Please ensure that the appliance is installed in accordance with these installation instructions and that the handle is fitted correctly Should you require further assistance please contact your Miele customer service centre Climate range The appliance is designed for use within certain climate ranges ambient temperatures and should not be used outside this range The climate range of the appliance is stated on the data plate inside the appliance Climate range Ambient room temperature SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C Operating in aroom which is too cold will cause the cooling system to switch off for too long causing the internal temperature in the appliance to rise with the risk of food deteriorating and going off Installation Ventilation Air at the back of the appliance gets warm The appliance housing unit must be constructed to allow sufficient space for ventilation A ventilation gap of at least 38 mm depth must be allowed for behind the appliance for air to circulate The air inlet to the appliance is via the
25. harmful to the eyes In the event of any damage avoid open fires and anything which creates a spark disconnect from the mains air the room in which the appliance is located for several minutes and contact the Service Department for advice gt The more coolant there is in an appliance the larger the room it should be installed in In the event of a leakage if the appliance is in a small room there is the danger of combustible gases building up For every 8 g of coolant at least 1 m of room space is required The amount of coolant in the appliance is stated on the data plate inside the appliance gt Before connecting the appliance to the mains supply make sure that the rating on the data plate corresponds to the voltage and frequency of the household supply This data must correspond in order to avoid the risk of damage to the appliance Consult a qualified electrician if in any doubt gt The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for damage or injury caused by the lack of or inadequacy of an effective earthing system e
26. he fully extended runners The front of the runners must be right up against the front of the compartment m Then push the compartment back in 24 Adjusting the condiment tray bottle shelf m Lift the tray shelf up and out of the stainless steel frame to remove m Push up the stainless steel frame and remove m Replace the frame at the required height Ensure that it is securely pushed back into position m Replace the tray shelf in the frame The tray shelf can be removed completely and used as a serving tray at the table Adjusting the interior fittings Universal container Moving the bottle divider depending on model depending on model The universal container can be used The bottle divider can be moved to the both to store and serve food left or right to ensure that bottles are held securely in position when the door is opened and shut The bottle divider can be removed completely e g for cleaning m To do this push up the front edge of the bottle divider and disengage it It consists of a deep tray anda shallow tray Both trays fit the stainless steel frame If you wish to use the universal container to serve food m place the shallow tray in the stainless steel frame and use the deep tray as a lid You can lift the universal container including contents out of the frame and take it to the table 25 Automatic defrost Refrigerator sect
27. igerator is automatically shown If you have adjusted the temperature wait for approx 6 hours if the appliance is not very full and for approx 24 hours if the appliance is full before checking the temperature display as it will take this long for the display to give an accurate reading If after this time the temperature is still too high or too low you will need to adjust it again Temperature range The temperature can be adjusted from 4 C to 9 C The ambient temperature in the room and the installation location can affect the time it takes for the appliance to reach the lowest temperature If the ambient temperature is too high the appliance may not reach the lowest temperature Setting the temperature in the PerfectFresh zone The temperature in the PerfectFresh zone is automatically held at O to 3 C It can be raised or lowered e g if you want to use it for storing items like fish coe m Press and hold the Super cool button pressed in for approx 5 seconds The Super cool indicator light flashes and a flashes in the temperature display SER m Press one of the temperature selector buttons repeatedly until a amp appears in the display Press the Super cool button again 6 lights up in the display m You can now adjust the temperature in the PerfectFresh zone by pressing the temperature selector buttons You can choose from settings 7 to 9 7 lowest temperature 5 highest tem
28. ion and PerfectFresh zone The refrigerator section and the PerfectFresh zone defrost automatically Condensate and frost can build up on the back wall of the refrigerator section and the PerfectFresh zone whilst in use You do not need to remove this as it will defrost and evaporate automatically with the warmth generated by the appliance The condensate is drained away via a channel and drain hole into an evaporation system at the back of the appliance Ensure that the condensate channel and drain hole are kept clean and are never blocked so that condensate can flow away without hindrance 26 Cleaning and care Never use cleaning agents containing abrasive substances such as sand soda acids chlorides Or chemical solvents Non abrasive cleaning agents are also unsuitable as they can cause matt areas to appear To help prevent re soiling treat stainless steel surfaces with a proprietary conditioning agent for stainless steel available from the Miele Spare Parts Department or via the internet on www miele co uk Do not let water get into the electronic unit or the light Do not let water get into the drainage channel and drain hole when cleaning Do not use steam cleaning apparatus to clean the appliance Steam could reach the electrical components and cause a short eircuit The data plate located inside the appliance must not be removed It contains information which is required in the event of
29. it the sealing strip so that it meets up with the lower edge of top cover and then cut the sealing strip 2 3 mm above bottom fixing bracket m Push the appliance into the niche until covers and touch the front edge of the side walls of the housing unit 44 Building in the appliance With 16 mm thick walls The spacers should touch the front edge at the top and bottom of the side walls of the housing unit detail With 19 mm thick walls The front edges of the top and bottom hinges sit flush with the front edge of the housing unit side walls detail m Make sure that the covers on the top and bottom fixing brackets sit flush with the front edges of the housing unit side walls detail This will create a gap all round of 42 mm to the front edges of the housing unit side walls Building in the appliance On furniture with door fittings e g stubs seals etc the dimension of these must be taken into account when making sure there is a gap all round of 42 mm m Pull the appliance forwards by the dimension of the door fitting to keep the gap at 42 mm all round The hinges and the covers will now protrude by the dimension of the door fitting Tip Removing the door fittings This will ensure that the door is flush with the surrounding kitchen unit furniture doors If the all round gap of 42 mm is not maintained between the appliance casing
30. k of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Safety with children gt This appliance is not a toy To avoid the risk of injury do not allow children to play on or near it or to play with the controls Older children may only use the appliance if its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse gt Keep children away from the appliance at all times and supervise them whilst you are using it Warning and Safety instructions Technical safety gt gt Before setting up the appliance check it for any externally visible damage Do not install and use a damaged appliance R600a gt This appliance contains the coolant Isobutane R600a a natural gas which is environmentally friendly Although it is flammable it does not damage the ozone layer and does not increase the greenhouse effect The use of this coolant has however led to a slight increase in the noise level of the appliance In addition to the noise of the compressor you might be able to hear the coolant flowing around the system This is unavoidable but does not have any adverse effect on the performance of the appliance Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged Leaking coolant can be
31. lastic parts or which could cause a build up of gases and pose a danger to health gt Do not use any oils or grease on the door seal as these will cause the seal to become porous with time gt Do not store cooking oil in the refrigerator door Traces of oil can cause stress cracks to occur in the plastic components in the door gt Do not block the ventilation gap in the plinth or the top of the appliance housing unit as this would impair the efficiency of the appliance increase the electricity consumption and could cause damage to the appliance gt The appliance is designed for use within certain climate ranges ambient temperatures and should not be used outside this range The climate range for your appliance is stated on the data plate inside the appliance Installing it in a room with too low an ambient temperature e g a garage can lead to the appliance switching off for longer periods so that it cannot maintain the required temperature 10 gt Never use a steam cleaning appliance to clean this appliance Pressurised steam could reach the electrical components and cause a short circuit Disposal of your old appliance gt Before disposing of an old appliance first make the door latch or lock unusable This way you will prevent children from accidentally locking themselves in and endangering their lives gt Be careful not to damage any part of the pipework whilst awaiting disposal e g by
32. lose mechanism m Place the door with the outer side downwards on a stable surface m Screw ball joint of soft close mechanism into the new fixing holes m Push tension spring inwards again m Screw mounting onto the hinge and tighten securely m Open out soft close mechanism and hook it onto ball joint W Changing the door hinging m Push the appliance door onto the pre fitted screws and then tighten the screws m Replace covers and m Replace the locking pins into the top of the hinges to prevent the doors opening too far 41 Building in the appliance All fitting instructions given are for a right hand hinged appliance If you have converted the appliance to left hand hinging you will need to adapt these instructions accordingly To install the appliance you will need the following across slotted screwdriver a selection of Torx screwdrivers a hexagon spanner Weight of the furniture door Before fitting a furniture door ensure that the weight of the door does not exceed the maximum permitted Maximum weight of APPIIaNEE furniture door in kg K 9457 iD 1 19 K 9557 iD 1 15 K 9757 iD 1 19 Fitting a door which is heavier than the maximum permitted could damage the hinges 42 Building into a peninsular run When built into a peninsular run the rear of the building in niche must be fitted with a kitchen fur
33. n be raised or lowered to the required level The raised edge at the back must face upwards to prevent food from touching the back of the appliance and freezing to it Stoppers prevent the shelves from being dislodged by mistake Split shelf In order to accommodate tall items in the appliance one of the shelves is divided The front section can be pushed under the rear section m Push the rear half of the glass shelf up slightly from below m At the same time pull the front half of the glass shelf forwards slightly and then push it carefully under the rear half To move the split shelf m Take both halves of the split glass shelf out m fit the two brackets onto the supports on either side at the required height m and push the glass shelves in one after the other The shelf with the raised edge must be at the back 23 Adjusting the interior fittings PerfectFresh zone compartments The compartments in the PerfectFresh zone are on telescopic rails and can be removed for filling emptying or cleaning purposes m Pull out the compartment as far as it will go and then lift it up and out Push the runners back in again to avoid injury or damage m Carefully pull out the lid between the compartments slightly and lift it down and out m TO replace it insert the compartment lid from beneath into the holders and push it back into place To replace the compartment m place it back on t
34. n the door is opened briefly but the temperature display is working then the light is defective m Call the Service Department The LED lighting may only be repaired or changed by a service technician Danger of injury and damage Should the cover be damaged or need to be removed due to damage exercise caution Never look at the lighting with optical instruments magnifying glass or similar the floor of the refrigerator is wet The drain hole is blocked m Clean the condensate channel and drain hole If you still cannot remedy the fault having followed these suggestions please contact the Miele Service Department To prevent unnecessary loss of temperature it is advisable not to open the door while waiting for the appliance to be serviced 30 Noises Normal noises What causes them Brrrrr Humming noise made by the motor compressor This noise can get louder for brief periods when the motor is switching on Blubb blubb A gurgling noise can be heard when coolant is circulating through the pipes Click Clicking sounds are made when the thermostat switches the motor on and off Sssrrrrr On multi zone and frost free appliances you can sometimes just hear the movement of air circulating inside the appliance Remember that the noise of the compressor and the coolant circulating in the system is unavoidable Noises that you can What causes them and what can you
35. niture panel Aligning the housing unit The housing unit must be carefully aligned using a spirit level before installing the appliance The unit corners must be at right angles as otherwise the furniture door will not align correctly with the 4 corners of the appliance Building in the appliance Preparing the appliance m Slide cover strip into the holder in the middle of the appliance as illustrated with the bumps facing downwards The bumps will fit into the keyhole slots Position the mains electricity cable so that the appliance can be connected easily once installed Push the appliance two thirds of the way into its niche When doing this make sure that the mains cable does not get trapped With 16 mm thick furniture walls clip spacers over the hinges m Open the appliance door m Using a screwdriver remove cover G from the top corner of the appliance m Fit cover onto fixing bracket m Secure fixing bracket to the top of the appliance with screws M5 x 15 43 Building in the appliance m Fit cover onto fixing bracket m Secure fixing bracket to the bottom of the appliance with screws M5 x 15 m Carefully remove the protective foil from sealing strip 49 m Apply the sealing strip to the side of the appliance on which the door is opened so that it is flush with the front edge of the appliance F
36. ontact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk Internet www miele hk India Miele Appliances India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa iele Pty
37. perature 6 5 is the default setting for the PerfectFresh zone If a setting of 6 7 tob 4 is selected the temperature can fall below 0 C Food could freeze m Press the Super cool button to save the setting CO Ss N m Press the On Off button to come out of setting mode If you do not do this the electronics will switch over to normal operation automatically after a couple of minutes The correct temperature Temperature display During normal operation the temperature display on the control panel shows the average temperature in the refrigerator If the temperature is not within the range that the appliance is able to display bars will flash in the temperature display Temperature display brightness The appliance is supplied with the brightness of the temperature display set as low as possible However if the door is opened a setting changed or if the alarm is sounding the temperature display will appear much brighter The level of brightness can be adjusted cz N m Press and hold the Super cool button pressed in for approx 5 seconds The Super cool indicator light flashes and ac flashes in the temperature display CE je m Press one of the temperature selector buttons repeatedly until appears in the display m Press the Super cool button again h lights up in the display 16 m You can now adjust the level of brightness by pressing the temperature selector buttons Yo
38. r contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person Take care not to damage the pipework at the back of it before or during transportation to an authorised collection depot In this way refrigerant in the pipework and oil in the compressor will be contained and will not leak out into the environment Warning and Safety instructions This appliance complies with all relevant legal safety reguirements Improper use of the appliance can however present arisk of both personal injury and material damage To avoid the risk of accidents and damage to the appliance please read these instructions carefully before installation and before using it for the first time They contain important notes on the installation safety operation and care of the appliance Keep these instructions in a safe place and pass them on to any future user Correct application gt This appliance is intended for domestic use only for the cool storage of food and drink Any other usage is not supported by the manufacturer and could be dangerous The manufacturer cannot be held liable for damage resulting from incorrect or improper use or operation gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lac
39. r rare ni eee Ea nern T TA ee eee es 28 Problem solving guide 29 NOISES AA eed ee KA ka ee a RER ean ak b eee ante 31 After Sales Guarantee 32 Electrical connection 33 Installation IIIA ae nenn an 34 POC AU OMe e nae AR A IA E E 34 Side by side 34 Climate aa EA AAA AAA WA AAA AAA 34 Ventilation s ii AAA 35 Before Installation IIIA AIKA 35 Does your old appliance have a different hinging mechanism 35 Stainless Steel Ont er nats i kee ga geen sd as en ews bak 36 Building in dimensions 37 Adjusting the door hinges 38 Changingthedoorhinging 39 WA WA ui te ae KUMBU EU MANA ee ne ee 39 Building in the appliance 42 Weight of the furniture door 0 0020 Aaaa 42 Building into a peninsular run IAA Aa 42 Fitting a Tunniture door 25 ao snk siege nea aa Die cee Seabee news 46 Guide to the appliance Safety lock indicator light 2 On Off button 3 Refrigerator temperature display Temperature selector buttons for warmer for colder Super cool button and indicator light Alarm off button Guide to the appliance
40. r the ambient temperature surrounding the appliance The appliance is designed for use in specific ambient temperatures climate ranges Do not use in ambient temperatures for which it is not designed n the refrigerator and the PerfectFresh zone We recommend a temperature of 4 C in the refrigerator The temperature in the PerfectFresh zone is controlled automatically and is maintained at 0 to 3 C 14 Dynamic cooling The dynamic cooling fan automatically switches on when the cooling system for the refrigerator switches on It distributes the temperature in the appliance to all areas more evenly so that all the food will be chilled to about the same degree Setting the temperature in the refrigerator Use the two buttons underneath the temperature display to set the temperature for the refrigerator Press the EEE EEE button to raise the temperature it gets warmer button to reduce the temperature it gets cooler The temperature being set will flash in the display When pressing the buttons the following information shows in the display When first pressed the last temperature selected flashes Each subsequent press of the button adjusts the temperature shown in 1 C steps Keeping the button pressed in adjusts the temperature continually The correct temperature Approx 5 seconds after letting go of the button the current average temperature of the refr
41. rticularly can be switched off once food and recommended for faster chilling of drinks are sufficiently chilled large amounts of fresh food or drink m Press the Super cool button The 2 Super cool indicator light will go out N and the appliance will continue to operate at normal power m Press the Super cool button The Super cool indicator light will come on The appliance will then work at full power to lower the temperature 18 Using the refrigerator efficiently Different storage zones Due to the natural circulation of the air in the appliance there are different temperature zones in the refrigerator Cold heavy air sinks to the lowest section of the appliance Make use of the different zones when placing food in the appliance This appliance has automatic dynamic cooling which helps to keep an even temperature when the fan is running For this reason the difference between the various zones is less pronounced Warmest area The warmest area is in the top section of the door Use this for storing butter and cheese Coldest area The coldest area in the refrigerator is directly above the PerfectFresh zone However the PerfectFresh zone is even colder Use these areas in the refrigerator and in the PerfectFresh zone for all delicate and highly perishable food e g fish meat poultry sausage products ready meals dishes or baked goods containing eggs or cream fresh dough
42. safety lock is de activated i the safety lock is activated m Press the Super cool button to save the setting The safety lock indicator light FF will light up when the safety lock has been activated N m Press the On Off button to come out of the setting mode If you do not do this the electronics will switch over to normal operation automatically after a couple of minutes Switching off for longer periods of time If the appliance is not going to be used for a longer period of time e g whilst on holiday m switch the appliance off m switch off at the wall socket and withdraw the plug m clean the appliance out and m leave the door ajar to air the appliance If during a long absence the appliance is switched off but not cleaned out and the door is left shut there is a danger of mould and odours building up inside the appliance The correct temperature Itis very important to set the correct temperature for storing food in the appliance Micro organisms will cause food which is not stored at the correct temperature to deteriorate rapidly Temperature influences the growth rate of these micro organisms Reducing the temperature reduces their growth rate The temperature in the appliance will rise the more often the door is opened and the longer it is kept open if too much food is stored in it at once the warmer the food is which is being put into it the highe
43. t foods rich in protein deteriorate faster than others Shellfish for example deteriorates faster than fish and fish deteriorates faster than meat 21 Using the PerfectFresh zone Always keep these foods covered or wrapped Exception Meat The surface of the meat dries out slightly helping to prevent the growth of bacteria which results in the meat lasting longer To prevent the risk of bacterial cross contamination and meat deteriorating do not let one type of meat come into direct contact with another type Humidity controlled compartment The humidity controlled compartment has a regulator which is used to adjust the relative humidity Slide the regulator to the relative humidity level required 666 high humidity low humidity If high humidity 666 is selected a humidity level of 90 can be achieved when the compartment is full The humidity depends strongly on the type and quanltiy of food being stored Please take into account that high humidity is only achieved and is only effective on the food if the food is stored unwrapped or loosely wrapped The humidty controlled compartment at the high humidity setting 666 is ideal for storing freshly harvested products such as vegetables salad heros mushrooms and home grown seasonal fruit At the low humidity setting 6 the atmosphere inside the humidity controlled compartment is the same as in the dry compartment 22 Take food out of
44. the PerfectFresh zone approx 30 60 minutes before using it The aroma and taste do not fully develop until the food has reached room temperature Can all types of food be stored together Do not place all types of food together in one drawer Some types of food do not store well together Aromas and flavours can transfer from one type of food to another e g carrots absorb the smell and flavour of onions very easily Some food also gives off a natural gas ethylene which speeds up the rate at which other food perishes Examples of fruit and vegetables which produce a large amount of this natural gas are Apples apricots pears nectarines peaches plums avocado figs blueberries melons and beans Examples of fruit and vegetables which react strongly to the natural gases given off by other types of fruit and vegetables are Kiwis broccoli cauliflower Brussels sprouts mangos honeydew melons apples apricots cucumbers tomatoes pears nectarines and peaches Example Broccoli should not be stored with apples as apples produce a large amount of natural gas to which broccoli is very sensitive The result is a shorter than expected storage time for the broccoli Adjusting the interior fittings Moving the shelves The shelves can be adjusted according to the height of the food m Raise the shelf and pull it forwards slightly until the notch at the side is in line with the shelf support It can the
45. the alarm off early Ua 17 Switching on the alarm system 2 22 000 cet 17 S per Cool iii ee ee 18 Using the refrigerator efficiently 19 Different storage ZONES 19 Food which should not be stored in arefrigerator 20 When shopping fOr food as nsei Hear er 20 StoriNgTOOA COFFECIY tens ds re ee a ehr 20 Unpacked meat and vegetables 20 Using the PerfectFresh zone 21 Storage temperature sews sigare skeen ana gear an ana 21 Humidity level WW aa eee 21 Storing food in the dry and humidity controlled compartments 21 The dry Eompantment rare entre Pea ee daa ee 21 Humidity controlled compartment iia een en 22 Contents Adjusting the interiorfittings 23 MOVING ES EE IIIA wa rennen 23 SA Mesa ee ern re Bee ee 23 Adjusting the condiment tray bottle shelf 24 Universal container IAEA E o a a E a O E aaa 25 Moving the Dolla 25 Automatic defrost 26 Refrigerator section and PerfectFresh zone 26 Cleaning and care 27 Cleaning the interior and accessories 27 Ventilation Gaps sse es erra iarra i En ee 28 Door Seal sx rn a
46. u can choose from settings 7 to 5 i dimmest setting 5 brightest setting m Press the Super cool button to save the setting CO Ss N m Press the On Off button to come out of setting mode If you do not do this the electronics will switch over to normal operation automatically after a couple of minutes Alarm Your appliance has been fitted with an alarm to avoid energy being wasted if the door is left open and to prevent stored food becoming too warm The alarm will sound if the door is left open for more than approx 60 seconds The alarm will stop as soon as the door is closed If you want to keep the door open for more than approx 60 seconds intentionally we recommend that you switch the alarm off Switching the alarm off early EN N m Press the alarm off button The alarm will stop Switching on the alarm system The alarm system switches back on automatically as soon as the door is closed It does not have to be switched on manually Super cool Super cool Switching off Super cool The Super cool function can be used to The Super cool function will switch itself rapidly reduce the temperature in the off automatically after approx 6 hours refrigerator section to its lowest setting The indicator light will go out and the depending on the room temperature appliance will run at normal power again Swishina om Super cool To save energy the Super cool function Super cool is pa
Download Pdf Manuals
Related Search