Foxconn 661FX7MF-S motherboard
Contents
1. 3 Hold components by their edges to avoid touching any exposed integrated circuits ICs 4 Whenever you uninstall a component place it on a grounded anti static pad or into anti static bag that it came in 661FX 7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions CPU This motherboard supports single Pentium 4 Processor including Prescott desktop CPUs in an LGA 775 package It also supports Hyper Threading Tech nology and FSB Dynamic Bus Inversion DBI Installation of CPU Below is the CPU socket illustration Follow these procedures to install a CPU Load stiffener 1 Use thumb amp forefinger to hold the lifted tab of the cap 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions 3 Use thumb amp forefinger to hold the hook of the load lever and pull the lever sideways to unlock it Warning DO NOT use finger to lift or tick the locking lever the improper opera tion will cause finger hurt and the SKT in a poor operation condition A Lift up the lever Use thumb to open the load plate Be careful not to touch the contacts Cin hid D zt Een WE _ D 5 Hold the CPU and tilt it to some degree since the contacts are designed to be hooked then match the triangle marker to Pin 1 position as shown below Carefully insert the CPU into the socket until it fits in place Pin 1 indicator 661FX7MF 648FX2. Installation of DDR Memory 1 There is only one gap in the center of the DIMM socket and the memory module can be fixed in one direction only Unlock a DIMM socket by pressing the module clips outward 2 Align the memory module to the DIMM socket and insert the module verti cally into the DIMM socket 104 80 Pins Pins 3 The plastic clips at both sides of the DIMM socket will lock automatically mm emm mm Be s M if WI 1 8 RI 4 i eae i gee hepni aae EREET e En oil a IEn w a EE AE t UAVS TET ee Teste et T d E E oe e e E E re e em rm re re re D Warning Be sure to unplug the AC power supply before adding or removing expansion cards or other system peripherals especially the memory devices otherwise your motherboard or the system memory might be seriously damaged 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions Memory Qualified Vendor List The following table lists the Memory modules that have been tested and quali fied for use with this motherboard 661FX 7MF amp 648FX7MF Series HLX DDR400 256M KINGMAX DDR400 433 512M LPT DDR466 512M SAMSUNG DDR333 512M SAMSUNG DDR266 256M BAMBO DDR333 256M KINGMAX DDR333 256M INFINEON DDR266 256M Apacer DDR400 512M Apacer DDR333 256M LPT DDR466 256M 512M CORSAIR DDR466 256M CORSAIR DDR500 256M TWINMOS DDR333 1G i Note Make sure to use only the tested and qualified DDR DIMMs listed above Other
3. TU CHENG INDUSTRIAL DISTRICT TAIPEI HSIEN TAIWAN R O C declares that the product Motherboard 661FX7MF 648FX7MF 648C7MF series is in conformity with reference to the specification under which conformity is declared in accordance with 89 336 EEC EMC Directive lV EN 55022 A1 2000 Limits and methods of measurements of radio disturbance characteristics of information technology equipment V EN 61000 3 2 A14 2000 Electromagnetic compatibility EMC Part 3 Limits Section 2 Limits for harmonic current emissions equipment input current lt 16A per phase V EN 61000 3 3 A1 2001 Electromagnetic compatibility EMC Part 3 Limits section 2 Limits of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current lt 16A V EN 55024 A1 2001 Information technology equipment Immunity characteristics limits and methods of measurement d Signature Je Lint Place Date TAIPEI 2004 lt Printed Name James Liang Position Title Assistant President Declaration of conformity Trade Name Model Name Responsible Party Address Telephone Facsimile Equipment Classification Type of Product Manufacturer Address Supplementary Information Foxconn 661FX7MF 648FX7MF 648C7MF PCE Industry Inc 458 E Lambert Rd Fullerton CA 92835 714 738 8868 714 738 8838 FCC Class B Subassembly Motherboard HON HAI PRECISION INDUSTRY COMPANY LTD 66
4. select Enabled to allow caching of the Video BIOS which may improve performance If any other program writes to this memory area a system error may result The available setting values are Enabled and Disabled Memory Hole at 15M 16M Default Disabled This option is used to determine whether the 15M 16M address field of memory is reserved for the ISA expansion card The available setting values are En abled and Disabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Phoenix AwardBlOS CHOS Setup Utility DRAH Clock T ining Control KA Tining Control By SPD 61 Henu Level Fe i x Mi 1U x Hi Pre WP li AT Tac Rouge Enter Select FU FD Value Fi Save ESC Exit Fi General Help F5 Previous Values P Fail Safe Defaults F Optinized Defaults DRAM Clock Timing Control Menu DRAM Timing control Default By SPD This option determines DRAM timing using SPD or manual configuration Only set as manual the following 4 items can be updated DRAM CAS Latency Default depend on memory This option determines CAS Latency The available setting values are 2T 2 5T 3T RAS Active Time tRAS Default depend on memory This option determines RAS active time The available setting values are 4T sdi RAS Precharge Time tRP Default depend on memory This option is used to define the idle clocks after issuing a precharge com mand to the SDRAM RAS to CAS De
5. Default 32 MB only for 661FX7MF This option is used to set the onboard VGA share memory size The available setting are 16MB 32MB 64MB 128MB Graphics Engin Clock Default 133 MHz only for 661FX7MF This option is used to set onchip AGP graphics engin clock The available setting are 100 MHz 133MHZ 166MHZ 200MHz 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 3 BIOS Description Integrated Peripherals Phoenix AwardBIOS CHOS Setup Utility Integrated Peripherals t S18 OnChip IDE Device Press Enter Iren Help FSIS OnChip PLI Device Press Enter H Onboard SuperlO Device Fress Enter IDE ock Aode Enabled Onboard Lan Hoot ROM Disabled Init Display First FCI Slot USER Access Interface EDE Bus es Interface EDP Bus ss Interface EDE Bus ss Interface EDE Bus ss Interface EDH Bus Audio Access Interface EDE Bus Ti Hove Enter Select PU SPD Value Fi Save E E Help FS Peevious Values Fi Fail Safe Defaults tinized Defaults Integrated Peripherals Menu SIS Onchip IDE Device Press enter to set onchip IDE device Please refer to page 42 SIS Onchip PCI Device Press enter to set onchip PCI device Please refer to page 43 Onboard SuperIO Device Press enter to set onboard superlO device Please refer to page 44 IDE HDD Block Mode Default Enabled This option is used to set whether the IDE HDD block mode is allowed The available setting values are Disabled and En
6. CHUNG SHAN RD TU CHENG INDUSTRIAL DISTRICT TAIPEI HSIEN TAIWAN R O C This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Tested to comply with FCC standards Signature Date 2004 Table of Contents Chapter Product Introduction Main BE EE 2 Motherboard Layout 5 Chapter Installation Instructions EE 8 YS le it E E On 12 Power SUI EE 44 Rear Panel Connectors ccc cece ccc ccc ee cecceece cee seuecuecuesuesuesaeeeeeesnaeenesaeene 15 Other COMME CONS tage dead 17 EOSO G EE 21 EMMIS a 23 Chapter BIOS Description Enter BIOS Setup anananananannnnnnnnnnnnnnnnnnnrnnnnranenerenenernnnrnnnnrnrnrererrrerererrnne 26 Main VC NEE 26 Standard CMOS Features 28 Eileen EN Advanced BIOS Features cccecccccccecceeseeeseeeseeuseeeeeeeeeeseeeseaeueaeeeaueeaeens 32 Advanced Chipset Features ccccsssccccsseeecsseseecesseeeceueeeseseesseeseessaaees 37 Integrated Peripherals AA 41 Power Management Setup ccccccseesceeeceeeceeseeeeeeeeseeeeeeeseeaeeeeeseeeeeeeeas 45 ale GOR AMON esen E E E 49 PO SE Un Ee CHE 50 Frequency Voltage Control 51 Load Fail Safe Defaults ssicsnaicontdtasieniadenhevsdniasuideieaidonstecesseendicosnedetnioaeedes 52 Lo
7. DDR DIMMs manufactured by other vendors may not be suitable for this motherboard 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions Power Supply This motherboard uses an ATX power supply In order to avoid damaging any devices make sure that they have been installed properly prior to connecting the power supply 20 pin ATX power connector PWR1 Ee PWR1 is the ATX power supply connector a Se Se EN Make sure that the power supply cable and pins are properly aligned with the connector on the motherboard Firmly plug the power supply cable into the con nector and make sure it is secure 4 pin ATX 12V Power Connector PWR2 The ATX power supply connects to PWR2 and provides power to the CPU Attention You have to press the power button for more than four seconds if you change the default Instant Off setting to Delay 4 Sec from the Power Button Override option in the BIOS Power Management Setup 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions Rear Panel Connectors This motherboard provides the ports as below 4 Parallel Port z LAN Connector Printer Port PSi2Mouse 4D g Connector er PS 2 Keyboard Dn eg Connector A La z Microphone jack Serial Port O VGA Port QO USB 2 0 Ports ol 1394 Port COM1 only for 661FX7MF optional PS 2 Mouse Connector This green 6 pin connector i
8. Left Front Right Rear Left gait WRear Right 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions Other Connectors This motherboard includes connectors for FDD IDE HDD USB CPU fan system fan and others FDD Connector This motherboard includes a standard FDD connector supporting 360K 720K 1 2M 1 44M and 2 88M FDDs HDD connectors PIDE amp SIDE This connectors supports the provided Ultra DMA 133 100 66 IDE hard disk ribbon cable Connect the cable s blue connector to the primary recommended or secondary IDE connector then connect the gray connector to the Ultra DMA 133 100 66 slave device hard disk drive and the black connector to the Ultra DMA 133 100 66 master device If you install two hard disks you must configure the second drive as a slave device by setting its jumper accordingly Refer to the hard disk documentation for the jumper settings attention Ribbon cables are directional therefore make sure to always connect with the cable on the same side as pin 1 of the PIDE SIDE or FDD connector on the motherboard 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions Front Panel Connector F P1 This motherboard includes one connector for connecting the front panel switch and LED indicators Hard Disk LED Connector IDE_LED The connector connects to the case s IDE indicator LED indicating the activity status of IDE har
9. Max Saving Suspend Mode Default Disabled This option is used to set the idle time before the system enters into sleep status The setting values are Disabled and 1 Min 1 hour Video Off Option Default Susp Stby gt Off This option is used to set video off option The setting values are Always On Suspend gt Off Susp Stby gt Off All Modes gt Off 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Video Off Method Default DPMS Supported This option is used to define the video off method Blank Screen mode means that after the computer enters power saving mode only the monitor will close however the vertical and horizontal scanning movement of the screen continues When you select the V H SYNC Blank mode the vertical and horizontal scanning movement of screen stops when the computer enters power saving mode DPMS Supported mode is a new screen power management system and it needs to be supported by the monitor you re using Switch Function Default Break Wake This option is used to enable or disable switch function to wake up The setting values are Break Wake and disabled MODEM Use IRQ Default AUTO This option is used to set the IRQ in which the modem can use The system will automatically wake up when the modem receives an incoming call Hot Key Function As Default Power Off The option is used to define the hot key function The avai
10. Setup The BIOS ts the communication bridge between hardware and software correctly setting up the BIOS parameters Is critical to maintain optimal system performance Power on the computer when the following message briefly appears at the bottom of the screen during the POST Power On Self Test press lt Del gt key to enter the AWARD BIOS CMOS Setup Utility Press TAB to show POST screen DEL to enter SETUP ET Note We do not suggest that you change the default parameters in the BIOS Setup and we shall not be responsible for any damage that result from any changes that you make Main Menu The main menu allows you to select from the list of setup functions and two exit choices Use the arrow keys to select among the items and press lt Enter gt to accept or go to the sub menu Phoenix AwardBIOS CHOS Setup Utility k Standard CHOS Features F FrequencyVoltage Control H BIOS Features Load Fail Safe Defaults F Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password H Integrated Peripherals k Power Management Setup Save amp Exit Setup F PoF PG Configurations Exit Without Saving t PC Health Status Ese Quit ti e Select Item FiB Save amp Exit Setup Time Date Hard Disk Type Main Menu The items in the main menu are explained as below Standard CMOS Features The basic system configuration can be set up through this menu BIOS Features The special features can be
11. available setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 BIOS Description Full Screen LOGO Show Default Fnabled This option allows you to enable or disable the full screen logo The available setting values are Disabled and Enabled Small Logo EPA Show Default Disabled This option allows you to enable or disable the EPA logo The available setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description enix AwardBIOS CHOS Setup Utility CP Feature enu Leve 0 Wiem Limit CPUID MaxVal Disabled Hk BIOS Control Enabled Thermal Monitor 1 On die throtting re l Honito wo amp UID Ss dt tie mn Tl Move Enter Select PUCPD Value Fi Save ESC Exit FPi General Help FS Previous Values Pe Fail Safe Defaults F Optimized Defaults CPU Feature Menu Thermal Management Default Thermal Monitor 1 This option is used to manage Prescott CPU thermal Note This option will not be displayed until a Prescott CPU has been installed TM2 Bus Ratio Default depend on CPU optional Represents the frequency bus ratio of the throttled performance state that will be initiated when the on die sensor goes from not hot to hot TM2 Bus VID Default depend on CPU optional Represents the voltage of the throttled performance state that will be initi ated when the on die sensor go
12. front panel USB cable optional to provide addi tional four USB ports Fan Connectors CPU FAN FAN1 The speed of CPU_FAN and FAN1 can be de tected and viewed in PC Health Status sec tion of the CMOS Setup These fans will be au tomatically turned off after the system enters suspend mode Audio Connectors CD IN CD_IN is Sony standard CD audio connector it can be connected to a CD ROM drive through a CD audio cable 1394 Header F 1394 optional The 1394 expansion cable can be connected to either the front provided that the front panel of your chassis is equipped with the appropriate interface or real panel of the chassis 661FX7MF 648FX7MF 648C7MF Series User Manual 1 5V Empty RX GND TX IR VCC VCC D D D D GND GND Empty NC F_USB1 2 CONTROL SENSE CPU_FAN POWER 1 GROUND GND 12V SENSE SS u R 7H GND rs CD IN CD L TPA TPA GND GND TPB TPB 12V 12V Empty GND 9 10 F_1394 Chapter 2 Installation Instructions Audio Interface F AUDIO The audio interface provides two kinds of audio output choices the Front Audio the Rear Audio Their priority is sequenced from high to low Front MIC IN MIC GND Audio to Rear Audio If headphones are plugged sive gf into the front panel of the chassis using the Front NA Empty Audio then the Line out Rear Audio on the rear 4 OUT L EE panel will not work If you do not want to use the fei Front Audio pin 5 and 6 pin9
13. is used to set which action will wake up PS 2 mouse from 3 status The setting values are Disabled Click Move amp Click Power Up by Alarm Default Disabled This option is used to set the timing of the start up function In order to use this function the start up password function must be canceled Also the PC power source must not be turned off The setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Month Alarm This option is used to set the timing for the start up month The setting values contain 0 12 and NA Day of Month Alarm This option is used to set the timing for the start up day of the month The setting values contain 0 31 Time hh mm ss Alarm This option is used to set the timing for the start up time The setting values contain hh 0 23 mm 0 59 ss 0 59 Primary Secondary IDE Default Disabled When these items are enabled the system will restart the power saving timeout counters when any activity is detected on any of the drives or devices on the primary or secondary IDE channels The setting values are Disabled and Enabled FDD COM LPT Port Default Disabled When this option is enabled the system will restart the power saving timeout counters when any activity is detected on the floppy disk drive serial ports or the parallel port PCI PIR A D Default Disabled When this option is disabled a
14. not support FSB 800MHz CPU Chipset e 661FX7ME Series SiS 661FX North Bridge SiS 964 South Bridge e 648FX7MF Series SiS 648FX North Bridge SiS 964 South Bridge e 648C7MF Series SiS 648 North Bridge SiS 964L South Bridge system Memory DDR JC e Two 184 pin DIMM slots e Supports PC 3200 PC 2700 PC 2100 memory e Supports 128 Mb 256 Mb 512 Mb 1 Gb technology up to 2GB Note 648C7MF series motherboard do not support PC 3200 memory USB 2 0 Ports e Supports hot plug e Eight USB 2 0 ports four rear panel ports two onboard USB header providing four extra ports e Supports wake up from S1 and S3 mode e Supports USB 2 0 protocol up to 480 Mbps transmission rate Onboard Serial ATA qoticnal e 150MBps transfer rate e Supports two S ATA devices such as HDD etc e Supports RAID 0 RAID 1 and JBOD optional 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 1 Product Introduction Onboard 1394 E optional i e Supports hot plug e With rate of transmission up to 400Mbps e Self configured addressing e Can connect with 2 independent 1394 units synchronously at most such as HDD CD ROM Onboard LAN L sono ns e Supports 10 100Mbit sec Ethernet e LAN interface built in on board ACP 3x Sax e AGP 8X AGP 3 0 is the VGA interface specification that enabled enhanced graphics performance with high bandwidth speeds up to 2 12 GB s Onboard Audio ei E e AC 97 2 3 Specification Compli
15. set up through this menu 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Advanced BIOS Features The advanced system features can be set up through this menu Advanced Chipset Features The values for the chipset can be changed through this menu and the sys tem performance can be optimized Integrated Peripherals All onboard peripherals can be set up through this menu Power Management Setup All the items of green function features can be set up through this menu PnP PCI Configurations The system s PnP PCI settings and parameters can be modified through this menu PC Health Status This will display the current status of your PC Frequency Voltage Control Frequency and voltage settings can be adjusted through this menu Load Fail Safe Defaults The default BIOS settings can be loaded through this menu Load Optimized Defaults The optimal performance settings can be loaded through this menu however the stable default values may be affected Set Supervisor User Password The supervisor user password can be set up through this menu Save amp Exit Setup save CMOS value settings to CMOS and exit setup Exit Without Saving Abandon all CMOS value changes and exit setup 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Standard CMOS Features This sub menu is used to set up the standard CMOS features such as the date time HDD model and so on Use the
16. upon the first normal start up of your PC and the relevant parameters will be restored to help the system start up more quickly on each subsequent start up The available setting values are Disabled and Enabled vn SuperBIOS Protect SuperBIOS Protect Default Disabled superBIOS Protect function protects your PC from being affected by viruses e g CIH The available setting values are Disabled and Enabled SuperRecovery SuperRecovery Hotkey Default LSHIFT F12 SuperRecovery provides the users with an excellent data protection and HDD recovery function There are 12 optional hotkey and the default hotkey is LSHIFT F12 SuperSpeed CPU Clock Depending on the specification of the CPU The conventional over clock method uses the jumpers on the motherboard and it is both troublesome and apt to errors By using SuperSpeed a CPU can be overclocked by keying in the desired in the CPU clock range CPU DRAM Frequency Ratio Default SPD This option is used to set CPU DRAM Frequency Ratio DRAM Frequency This option is used to show DRAM frequency OH Warning Be sure your selection is right CPU overclock will be dangerous We will not be responsible for any damage caused 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Advanced BIOS Features Phoenix AwardBlOS CHOS Setup Utility Advanced BIOS Features t CPU Feature E Fress Enter Iten Help F Hard Disk Boot Priority Pre
17. 7MF 648C7ME Series User Manual Chapter 2 Installation Instructions 6 Close the load plate and slightly push down the tonque side Slightly push down the tongue side 7 Lower the lever and lock it to the load plate then the CPU is locked completely zi Note Excessive temperatures will severely damage the CPU and system Therefore you should install CPU cooling fan and make sure that the cooling fan works normally at all times in order to prevent overheating and damaging to the CPU Please refer to your CPU fan user guide to install it properly 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions CPU Qualified Vendor List The following table lists the CPUs that have been tested and qualified for use with this motherboard 661FX 7MF amp 648FX7MF Series Pentium prescott 800MHz Pentium prescott 800MHz Pentium prescott 800MHz Celeron D 533MHz Celeron D 533MHz Pentium prescott 800MHz 661FX7MF 648FX7MF 648C7ME Series User Manual 4 q Chapter 2 Installation Instructions Memory This motherboard includes two 184 pin dual in line memory module DIMM sockets You can install corresponding PC 3200 DDR400 PC 2700 DDR333 or PC 2100 DDR266 memory modules You must install at least one memory module to ensure normal operation If you install two modules they must be the same speed Mixed memory modules from different manufac turers is not recommended
18. DD is installed or set Auto means the system can auto detect the hard disk when booting up by choosing Manual and changing Access Mode to CHS the related information should be entered manually Enter the information directly from the keyboard and press lt Enter gt Cylinder number of cylinders number of heads write pre compensation Landing Zone Sector numberof sectors fT 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Award Phoenix BIOS can support 3 HDD modes CHS LBA and Large or Auto mode For HDD lt 528MB For HDD gt 528MB amp supporting LBA Logical Block Addressing Large For HDD gt 528MB but not supporting LBA Recommended mode Drive A B This option allows you to select the kind of FDD to be installed including None S60K 5 25 in 1 2M 5 25 in 720K 3 5 in 1 44M 3 5 in and 2 88 M 3 5 in Video The following table is provided for your reference in setting the display mode for your system EGA VGA Enhanced Graphics Adapter Video Graphic Array For EGA VGA SEGA SVGA or PGA monitor adapters CGA 40 Color Graphic Adapter powering up in 40 column mode CGA 80 Color Graphic Adapter powering up in 80 column mode MONO Monochrome adapter including high resolution monochrome adapters Halt On This category determines whether or not the computer will stop if an error is detected during powering up All Errors Whenever the BIOS det
19. IS OnChip PCI Device Menu SIS USB Controller Default Enabled This option is used to enable or disable SIS USB controller USB 2 0 Supports Default Enabled This option is used to enable or disable USB 2 0 USB Keyboard Support Default Enabled This option is used to enable or disable USB keyboard under legacy OS USB Mouse Support Default Enabled This option is used to enable or disable USB mouse under legacy OS SIS AC97 AUDIO Default Enabled This option is used to enable or disable SIS AC97 AUDIO SIS 10 100M ETHERNET Default Enabled This option is used to enable or disable SIS 10 100M ethernet SiS Serial ATA Controller Default Enabled This option is used to enable or disable SiS serial ATA controller The available setting values are Disabled and Enabled SiS Serial ATA Mode Default IDE This option is used to set Serial ATA mode The default is recommended The available setting values are IDE and RAID 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description enix AwardBlOS CMOS Setup Utility Onboard Super Device Onboard FIC Controller Enabled Iten Help 1 ENKEN EDU Onboard Serial Port Onboard Parallel Port Lave TAQ Parallel Fort Mode SPF ECP Hode Use DAA 3 Tl Move Enter Select PU PD Walue Fi Save ESC Exit Fi General Help FS Previous Values Ph Pail Safe Defaults F7 Optinized Defaults Onboard SuperlO Device Menu
20. MSI8923 GeForce FX5200 128M DDR ASUS V9180 GF4FX 440 8X 64M DDR All ATI9500 128M DDR MSI5800 GeForce FX5800 128M DDR TYAN9700 ATI9700 128M DDR ELIXIR FX5200 GeForce FX5200 128M DDR All ATI9000 64M DDR Note Make sure to use only the tested and qualified AGP cards listed above Other AGP cards manufactured by other vendors may not be suitable for this motherboard 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions Jumpers The users can change the jumper settings on this motherboard if needed This section explains how to use the various functions of this motherboard by changing the jumper settings Users should read the following contents carefully prior to modifying any jumper settings Description of Jumpers 1 For the jumpers on this motherboard pin 1 can be identified by the silk screen printed A next to it However in this manual pin 1 is simply labeled as 1 2 The following table provides some explanation of the jumper pin settings User should refer to this when adjusting jumper settings Sa See PE er Set eae and pin3 closed Clear CMOS Jumper CLS CMOS This motherboard uses the CMOS RAM to store all the set parameters The CMOS can be cleared by removing the CMOS jumper Normal Status How to clear CMOS Default 12 3 1 Turn off the AC power supply and quickly connect pins 1 and 2 together using the Kee Clearcmos D I 12 3 2 Return the jumper
21. Onboard FDC Controller Default Enabled This option is used to set whether the Onboard FDC Controller is enabled The available setting values are Disabled and Enabled Onboard Serial Port1 2 Default 3F8 IRO4 2F8 IRQ3 This option is used to assign the I O address and interrupt request IRQ for the onboard serial port 1 2 Note Do not try to set the same values for serial ports 1 and 2 Onboard Parallel Port Default 378 IRQ7 This option allows you to determine onboard parallel port controller I O ad dress and interrupt request IRQ Setting values include Disabled 378 IRQ 7 278 IRQ5 and 3BC IRQ7 Parallel Port Mode Default SPP Select an address and corresponding interrupt for the onboard parallel port Setting values include SPP EPP ECP ECP EPP ECP Mode Use DMA Default 3 Select a DMA Channel for the parallel port when using the ECP mode This field is only configurable if Parallel Port Mode is set to ECP The available setting values are 3 and 1 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Power Management Setup enix AwardBlOS CHOS Setup Utility Power Hanagement Setup ACPI function Enabled lten Help EA Sus pane pape 1 P05 Power Har User Define Aus Geer nd Ho de Video OFF Option ideo OFF Hethod BreakWake DO Power OFF Disabled Power Button Override Instant OFF Power State Res a Control Alwa aye OFF FPA Wake Up Eve Press Enter De lay Brin
22. Statement This manual is the intellectual property of Foxconn Inc Although the information in this manual may be changed or modified at any time Foxconn does not obligate itself to inform the user of these changes Trademark All trademarks are the property of their respective owners Version Users Manual V1 0 in English for 661FX7MF 648FX 7MF 648C7ME series motherboard P N 91 181 U48 M0 0E Symbol description KR Note refers to important information that can help you to use motherboard better i Attention indicates that it may damage hardware or cause data loss and tells you how to avoid such problems OH Warning means that a potential risk of property damage or physical injury exists More information lf you want more information about our products please visit Foxconn s website http Awww foxconnchannel com ltem Checklist Thank for your purchasing Foxconn s 661FX7MF 648FX 7MF 648C7MEF series motherboard Please check the package if there are missing or damaged items contact your distributor as soon as possible 661FX7MF 648FX 7MF 648C7ME series motherboard x1 Foxconn Utility CD x1 User s Manual x1 lt RAID Manual x1 optional lt IDE Ribbon Cable x1 FDD Ribbon Cable x1 I O Shield x1 lt S ATA Signal Cable x1 optional lt S ATA Power Cable x1 optional Declaration of conformity LE HON HAI PRECISION INDUSTRY COMPANY LTD 66 CHUNG SHAN RD
23. abled Onboard Lan Boot ROM Default Disabled This option is used to decide whether to invoke the boot ROM of the onboard LAN chip Init Display First Default PCI Slot This option is used to set which display device will be used first when your PC starts up The available setting values are AGP and PCI Slot e USBO 1 2 2 0 Access Interface Default EDB Bus This option is used to set USBO 1 2 2 0 Access Interface The available set ting values are PCI Bus and EDB Bus MAC Access Interface Default EDB Bus This option is used to set MAC access interface The available setting values are PCI Bus and EDB Bus audio Access Interface Default EDB Bus This option is used to set audio Access Interface The available setting values PCI B EDB Bus are PCI Bus and US 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Phoenix AwardBlOS CHOS Setup Utility SIS OnChip IDE Device Internal PCI IDE Both Iten Help IDE Primary Master PIO Auto IDE Primary Slave PIO Auto IDE Secondary Master FIO Auto IDE Secondary Slave PIO Auto Primary Master UltraDMA Auto Primary alee UltraDMA Auto secondary HasterllltraDH Auto Secondary Slave KC Auto IDE DAA transfer acces Enabled IDE Burst Hode Enabled Lac Buue Enter Select PU PD Walue FPi Save FESC Exit Pi General Help FS Previous Values F Fail Safe Defaults F Optinized Defaults SIS OnChip IDE Dev
24. ad Optimized Defaults ccccccccsceecceceesseeeeceeeeeeeseeeseeeeseeaeeesseseeeesaaaes 52 Set Supervisor User Password 52 Sys Noire Bol 0 6 EE 53 Ei VV OUP SAVING ME 53 Chapter Utility CD content Start to install drivers Table of Contents Driver CD Introduction Warning 1 Attach the CPU and heatsink using silica gel to ensure full contact 2 It is suggested to select high quality certified fans in order to avoid damage to the motherboard and CPU due to high temperatures 3 Never turn on the machine if the CPU fan is not properly installed 4 Ensure that the DC power supply is turned off before inserting or removing expansion cards or other peripherals especially when you insert or remove a memory module Failure to switch off the DC power supply may result in serious damage to your system or memory module OH Warning We cannot guarantee that your system will operate normally while over clocked Normal operation depends on the over clock capacity of your device Attention since BIOS programs are upgraded from time to time the BIOS de scription in this manual is just for reference We do not guarantee that the content of this manual will remain consistent with the actual BIOS version at any given time in the future Attention The pictures of objects used in this manual are just for your reference Please refer to the physical motherboard This manu
25. al is suitable for motherboard of 661FX 7MEF 648FX7MF 648C7MF series Each motherboard is carefully designed for the PC user who wants diverse features L supports onboard 100M LAN K supports onboard 1G LAN 6 supports 6 Channel Audio 8 supports 8 Channel Audio E supports 1394 function S supports SATA function R supports RAID function You can find PPID label on the motherboard It indicates the functions that the motherboard has For example O ULBA4160000BE PC 65M01 FE HELS On the blue mark of the PPID label it means the motherboard supports 6 Channel Audio 6 1394 function E onboard 100M LAN L SATA function S me Chapter Thank you for your buying Foxconn s 661FX MF 648FX 7MF 648C 7MF series motherboard This series of motherboard is one of our new products and offers superior performance reliability and quality at a reasonable price This motherboard adopts the advanced SiS 661FX 648FX 648 964 964L chipset providing users a computer platform with a high integration compatibility performance price ratio This chapter includes the following information Main Features Motherboard Layout Chapter1 Product Introduction Main Features Size e mATX form factor of 9 6 x 8 3 Microprocessor BD ny ding e Supports Intel Prescott T processor in an LGA775 package e Supports FSB at 533MHz 800MHz e Supports Hyper Threading technology Note 648C7MF series motherboard do
26. and 10 must be short and then the signal will be sent to the rear audio port S PDIF Out Connector SPD OUT optional 5V The S PDIF out connector is capable of provid Empty ing digital audio to external speakers or com a pressed AC3 data to an external Dolby digital SPD_OUT decoder Note The empty pin of S PDIF cable should be aligned to empty pin of S PDIF out connector Chassis Intruder Connector INIR The connector connects to the chassis security switch on the case The system can detect the chassis intrusion through the status of this connector If the connector has been closed once the system will send a message To utilize this function set Case Open Warning to Enabled in the PC Health Status section of the CMOS Setup Save and exit then boot the operating sys tem once to make sure this function takes effect Speaker Connector SPEAKER The speaker connector is used to connect peaker of the chassis 1 INTRUDERJ GND INTR 1 SPK Pull high Empty NC SPKJ SPEAKER 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions Expansion Slots This motherboard includes three 32 bit master PCI bus slots one AGP slot PCI Slots The expansion cards can be installed in the three PCI slots When you install or take out such cards you must make sure that the power plug has been pulled out Please read carefully the instructions provided for such cards and instal
27. ant e Supports S PDIF output e Onboard Line in jack Microphone jack Line out jack e Supports 5 1 channels audio setting via software Expansion Slots e Three PCI slots e One AGP slot BIOS e Licensed advanced AWARD Phoenix BIOS supports flash ROM plug and play ready e Supports HDD CD ROM or USB device boot up Green Function e Supports ACPI Advanced Configuration and Power Interface e Supports SO normal S1 power on suspend S3 Suspend to RAM S4 Suspend to disk depends on OS and S5 soft off 661FX 7MF 648FX7MF 648C7MEF Series User Manual Chapter1 Product Introduction Advanced Features e PCI 2 2 Specification Compliant e Supports Windows 98 2000 ME XP soft off e Supports Wake on LAN e Supports PC Health function capable of monitoring system voltage CPU temperature system temperature and fan speed 661FX7MF 648FX7MF 648C7ME Series User Manual oO AJ o o Fb oO MM Motherboard Layout 60 00000 CD_IN Connector 1894 Header optional PCI Slots COM2 Connector S PDIF OUT Connector optional FDD Connector South Bridge SiS 964 964L Front USB Headers 9 Speaker Connector 10 Chassis Intruder Connector 11 Front Panel Connector 12 System Fan Connector ET Note Chapter 1 Product Introduction we hees S O G Ge d d 13 Clear CMOS Jumper 14 IrDA Header optional 15 HDD Connector 16 20 pin ATX Pow
28. arrow keys select the item to set up and then use the lt PgUp gt or lt PgDn gt keys to choose the setting values Fheemix AwardBlOS CHOS Setup Utility Standard CMOS Features Date Cmmiddsyy Fri May 21 7004 Item Help Time Chhtewss 8 5S 0 IDE Channel O Master Hone t IDE Channel O Slave Hone Change the day month IDE Channel 1 Haster Hone year and century t TIDE Channel 1 Slave Hone IDE Channel Haster Hone IDE Channel 3 Waster Hone Drive 1 464 3 5 in Drive E Hone Henu Level Video Halt On thee Move Inter Select PU PD Value Fi Saue ESC Exit FiiGeneral Help FS Previous Values F Fail Safe Defaults d Defaults F7 Optimize Standard CMOS Features Menu Date This option allows you to set the desired date usually as the current date with the lt day gt lt month gt lt date gt lt year gt format Day weekday from Sun to Sat defined by BIOS read only Month month from Jan to Dec Date date from 1 to 31 can be changed using the keyboard Year year set up by users Time This option allows you to set up the desired time usually as the current time with lt hour gt lt minute gt lt second gt format IDE Channel 0 1 Master Slave amp IDE Channel 2 3 Master These categories identify the HDD types of 2 IDE channels installed in the computer system There are three choices provided for the Enhanced IDE BIOS None Auto and Manual None means no H
29. c Delay Msec Default 250 Use this option to define how many milliseconds must elapse before a held down key begins generating repeat characters Security Option Default Setup When it is set to Setup a password is required to enter the CMOS Setup screen When it is set to System a password is required not only to enter CMOS Setup but also to start up your PC APIC Mode Default Enabled This option is used to enable or disable APIC mode MPS Version Control For OS Default 1 4 This option is used to set up the version of MPS Table used in NT4 0 OS OS Select For DRAM gt 64MB Default Non OS2 This option is only required if you have installed more than 64 MB of memory and you are running the OS 2 operating system Otherwise leave this option at the default HDD S M A R T Capability Default Disabled This option is used to enable or disable hard disk M A R T support function The available setting values are Disabled and Enabled Report No FDD For WIN 95 Default No If you are using the Windows 95 and running a system with on floppy drive select es for this option to ensure compatibility with Windows 95 logo certification The available setting values are No and Yes Video BIOS Shadow Default Enabled This option is used to enable or disable Video BIOS Shadow If you enable this option the video BIOS will be copied to RAM Video shadow will increase the video speed The
30. d disk Reset Switch RESET Attach the connector to the Reset switch on the front panel of the case the system will restart when the switch is pressed Power LED Connector PLED Attach the connector to the power LED on the front panel of the case The Power LED indicates the system s status When the system is in SO status the LED is on When the system is in S1 status the LED is blink When the system is in S3 S4 S5 status the LED is off PLED PWRBTN Power Swith Connector PWRBITN Attach the connector to the power button of the case Pushing this switch allows the system 1 zl to be turned on and off rather than using the BEY een power supply button Ro COM2 Connector COM2 This connector accommodates a second serial Steg f 4 SIN port using an optional serial port bracket Con SOUT DIR nect the bracket cable to this connector then in Wa e stall the bracket into a slot opening at the back of i NA the system chassis 9 10 COM2 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions ITA Header IR tiaal This connector supports wireless transmitting and receiving device Before using this function configure the settings of IR Address IR Mode and IR IRQ from the Integrated Peripherals section of the CMOS Setup USB Headers F USB1 F USB2 Besides four USB ports on the rear panel the series of motherboards also have two 10 pin header on board which may connect to
31. e to GN i Zem a That Bu ve ae Select PU PD Walue Fi Save ESC Exit Pi General Help S Previous Values fo Fail Safe Defaults F Optinized Defaults Power Management Setup Menu vo ACPI function Default Enabled ACPI stands for Advanced Configuration and Power Interface ACPlis a standard that defines power and configuration management interfaces be tween an operating system and the BIOS In other words it is a standard that describes how computer components work together to manage system hardware In order to use this function the ACPI specification must be sup ported by the OS for example Windows 2000 or Windows XP The available setting values are Enabled and Disabled ACPI Suspend Type Default S1 POS This option is used to set the energy saving mode of the ACPI function When you select S1 POS mode the power will not shut off and the Supply status will remain as it is in S1 mode the computer can beresumed at any time When you select S3 STR mode the power will be cut off after a delay period The status of the computer before it enters STR will be saved in memory and the computer can quickly return to previous status when the STR function wakes When you select S1 amp S3 mode the system will automatically select the delay time Power Management Default User Define This option is used to set the power management scheme Available settings are User Define Min Saving and
32. ects a nonfatal error the syste No Errors The system boot will not stop for any errors that may TI Jeer o e rrop toran eror mat may it will stop for all other errors All But Diskette The system boot will not stop for a diskette error but it TTT Tee All But Disk Key The system boot will not stop for a keyboard or disk error but it will stop for all other errors 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 BIOS Description Memory This is a Display Only Category determined by POST Power On Self Test of the BIOS Base Memory The BIOS POST will determine the amount of base or conventional memory installed in the system Extended Memory The BIOS determines how much extended memory is present during the POST Total Memory Total memory of the system 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description BIOS Features Phoenix AwardBlOS CHOS Setup Utility BIOS Features SuperRoat Iten Help SuperBoot Disabled Louperilis Pratect Superb O Protect Disabled uperkei very SuperRecovery Hotkey LSHIFT F12 Supers peed CPU Clock 288 LP DUR Frequency Ratio SPD DRAM Freouenc Ti Aove Enter Select FU PFDWalue FIB Save ESC Exit FliGeneral Help FS ious Values F Fail Safe Defaults Pi Optinized Defaults BIOS Features Menu SuperBoot SuperBoot Default Disabled SuperBoot allows system relevant information to be stored in CMOS
33. er Connector 17 SATA Connector 18 Memory Slots 19 North Bridge SiS 661FX 648FX 648 20 CPU Socket 21 AGP 8X Slot 22 CPU Fan Connector 23 4 pin ATX 12V Power Connector 24 Front Audio Connector The above motherboard layout is provided for reference only please refer to the physical motherboard 661FX 7MF 648FX7MF 648C7ME Series User Manual doter This chapter introduces the hardware installation process including the installation of the CPU and memory It also addresses the connection of your power supply use of the rear panel connectors connection of hard drive and floppy drive data cables and setting up various other feature of the motherboard Caution should be exercised during the installation process Please refer to the motherboard layout prior to any installation and read the contents in this chapter carefully This chapter includes the following information CPU Memory Power Supply Rear Panel Connectors Other Connectors Expansion Slots Jumpers E Ze Ze Zef Ze Ze Chapter 2 Installation Instructions Si Notes Take note of the following precautions before you install compo nents or change settings 1 Use a grounded wrist strap or touch a safely grounded object such as an attached power supply before handling compo nents to avoid damaging them due to static electricity 2 Unplug the power cord before opening your chassis or touching any component
34. es from not hot to hot Limit CPUID MaxVal Default Disabled goticnal The option is used to set limit CPUID MaxVal The available setting values are Disabled and Enabled NX BIOS Control Default depend on CPU optional When disabled forces the NX feature flag to always return 0 The available setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Advanced Chipset Features Phoenix awardBlos CMOS Setup Utility Agran sz hips at Ee DRA ak Ak Al ining T okt 5 ba 3 Ente d Iren Help Kigd Bridge Aas F er Contre abla d er RAN tla Mesory Hole at 15H 16H DAAT we Ente Sele ot RS PD Value KS Save ESC Exit FLG ere naral He tel j WIOUs er F Fail Safe Defaults Ei Optiniz ed Defa ilts Advanced Chipset Features Menu DRAM Clock Timing Control Press enter to set the items about DDR RAM Please refer to page 38 AGP amp P2P Bridge Control Press enter to set the items about AGP Please refer to page 39 OnChip AGP Control only for 661FX7MF Press enter to set the items about onchip AGP Please refer to page 40 System BIOS Cacheable Default Enabled select Enabled to allow caching of the system BIOS which may improve performance If any other program writes to this memory area a system error may result The available setting values are Enabled and Disabled Video RAM Cacheable Default Enabled
35. he driver that you want to install and begin the setup steps Cl Note The following setup steps are based on Windows XP environment There may be some differences with other operating systems EIS Series Sa FOXCONN UtiTity o e Ve sf ka Follow screen order to install the motherboard drivers 661FX7MF 648FX7MF 648C7MF Series User Manual
36. ice Menu Internal PCT IDE Default Both This option is used to set the ports of onboard IDE The available setting values are Disabled Primary Secondary and Both IDE Primary Secondary Master Slave PIO Default Auto These four items let you assign which kind of PIO Programmed Input Output is used by IDE devices Choose Auto to let the system auto detect which PIO mode is the best or select a PIO mode from 0 4 Primary Secondary Master Slave UltraDMA Default Auto UltraDMA technology provides faster access to IDE devices If you install a device that supports UltraDMA change the appropriate item on this list to Auto The available setting values are Disabled and Auto IDE DMA transfer access Default Enabled This option is used to enable or disable IDE DMA transfer access IDE Burst Mode Default Enabled This option is used to enable or disable IDE burst mode 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Phoenix AwardBIOS CHOS ER Utility SIS OnChip PCI Devi SIS USE Controller Enabled Iren Help USE 2 8 Supports Enabled USE Keyboard Support Enabled Henu Level kk USB Mouse Support Enabled 313 ACT AUDIO Enabled SIS 16 100 ETHERNET Enah led Sif Serial ATA Controller Enabled Sis Serial ATA Rode IDE Ti Hove Enter Select WA ETA HUT ESC Exit Fi General Help FS Previous Values Po Fail Safe Defaults F Optinized Defaults S
37. l and set the necessary hardware and software for such cards such as the jumper or BIOS setup AGP Slot This motherboard has an AGP slot that supports 1 5V AGP cards AGP is an interfacing specification designed to display 3D images It provides a specialized 66MHz 32 bit channel to allow the graphic controller to directly access the master memory and supports 4X and 8X speeds Warning The motherboard may be damaged if a 3 3V AGP card is used Make sure that your AGP card is 1 5V specification Note the notches on the card golden fingers to ensure that they fit the AGP slot on your motherboard Installing an expansion card 1 Before installing the expansion card read carefully the documentation that came with it and make the necessary hardware settings for the card 2 Make sure to unplug the power cord before adding or removing any expan sion cards 3 Remove the bracket opposite the slot that you intend to use 4 Align the card connector with the slot and press firmly until the card is completely seated in the slot 5 Secure the card to the chassis with the screw you removed earlier 21 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions AGP Qualified Vendor List The following table lists the AGP cards that have been tested and qualified for use with this motherboard 661FX7MF amp 648FX7MF Series Vender Video Memory FX 5200 GEFORCE FX5200 128M DDR All ATI9200 128M DDR
38. lable setting values are Disabled Power off Suspend HDD Off After Default Disabled This option is used to define the continuous HDD idle time before the HDD enters power saving mode The setting values are Disabled and 1 Min 15 Min Power Button Override Default Instant Off This option is used to set the power down method This function is only valid for systems using an ATX power supply When Instant Off is selected press the power switch to immediately turn off power When Delay 4 Sec is selected press and hold the power button for four seconds to turn off power Power State Resume Control Default Always Off This option is used to control power resume state The available setting val ues are Always Off Always On Keep Pre State PM Wake Up Events Press enter to set the items of PM wake up Events Please refer to page 47 Delay Prior to Thermal Default None This option is used to set the delay time before the CPU enters auto thermal mode The setting values are None 1Min 2 Min 4 Min 8 Min 16 Min 32 Min 64 Min 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Fhoenix AwardBIOS CMOS Setup Utility RQ 3 7 9 15 Nal Ru 8 Break Suspend RING Power Up Control MACPME Power Up Control PCIPRE Power Wp Control PS2KB Wakeup from 3 PSZRS Wakeup from 3 Power Up by Alarm Month Alar lt Day of Honth Alarm x Tine hh mm ss Alarm Disabled Prima
39. lay tRCD Default depend on memory This option is used to define the minimum RAS to CAS delay using 1us granularity 68 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 3 BIOS Description Pa k Setup Utility Awardelos CHOS Setup AGP amp PZP Bridge Control 4GP Aperture Size raphic Window WR Conbin AGP Fast Write Support ab AGP Data Rate EM to Iten Help AHE OH Tan zMowg EnteriSelect PU PO alue El zaue ESC Exit FiliGeneral Help a Ce rif lte FS Previous Values FG Fail Safe Defaults T Optimized Gefaul AGP amp P2P Bridge Control Menu AGP Aperture Size Default 64 MB This option defines the size of the aperture if you use an AGP graphics adapter The aperture is a portion of the PCI memory address range dedicated for graphic memory address space Note This function does not work when Onboard VGA Is used Graphic Window WR Combin Default Disabled only for 661FX7MF This option is used to disable or enable Graphic Window Write Combin mode AGP Fast Write Support Default Disabled only for 661FX7MF Use this option to enable or disable AGP fast write support AGP Data Rate Default Auto only for 661FX7MF Use this option to set AGP data rate 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description AwardeTOS CHOS Setup Utility inchip Cp Control J MB WGA Share Henory Size ES Graphics Engin Clock BEE IFA VGA Share Memory Size
40. n select the desired option and press the lt F gt key Set Supervisor User Password The access rights and permissions associated with the Supervisor password are higher than those of a regular User password The Supervisor password can be used to start the system or modify the CMOS settings The User password can also start the system While the User password can be used to view the current CMOS settings these settings cannot be modified using the User password When you select the Set Supervisor User Password option the following message will appear in the center of the screen which will help you to set the password Enter Password Enter your password not exceeding 8 characters then press lt Enter gt The password you enter will replace any previous password When prompted key in the new password and press lt Enter gt 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 BIOS Description lf you do not want to set a password just press lt Enter gt when prompted to enter a password and in the screen the following message will appear If no password is keyed in any user can enter the system and view modify the CMOS settings Password Disabled Press any key to continue Under the menu Advanced BIOS Features Setup if you select System from the Security Option you will be prompted to enter a password once the system is started or whenever you want to enter the CMOS setting program If the incor rec
41. ntire hard disk CPU L1 amp L2 Cache Default Enabled This option is used to enable or disable the CPU L1 and L2 cache The available setting values are Disabled and Enabled CPU I3 Cache Default Disabled qotimal This option is used to enable or disable CPU L3 cache The available setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 BIOS Description Hyper Threading Technology Default Enabled optional This option is used to turn on or off the Hyper Threading function of the CPU The available setting values are Disabled and Enabled Note This function will not be displayed until a CPU that supports Hyper Threading has been installed CPU L2 Cache ECC Checking Default Enabled This option is used to enable or disable CPU L2 cache ECC Checking The available setting values are Disabled and Enabled Quick Power On Self Test Default Enabled Enable this option to shorten the power on testing POST and have your sys tem start up faster The available setting values are Disabled and Enabled First Second Third Boot Device Default Floppy Hard DiskCDROM This option allows you to set the boot device s sequence The available setting values are Floppy LS120 Hard Disk CDROM ZIP100 USB FDD USB ZIP USB CDROM LAN and Disabled vo Boot Other Device Default Enabled With this function set to enable the system will to boot from s
42. ny PCI device set as the master will not power on the system 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description PnP PCI Configurations Phoenix AwardBlOS CHOS Setup Utility PoP PG Conf igurat ions Reset Configuration Data Disabled Iten Help Resources Controlled By CAuto ESCD Menu Level F k TAQ Resources Press Enter Default is Disabled PCI UGA Palette Snoop Disabled Select Enabled to reset Extended Sustem ii Ca Til TA inf 1 ii of z the D E hoot Tl4 Nove Enter Select PU PD Value Fi Save ESC Exit Fi DA GE FS Previous Values Fail Safe Defaults PI Optinized Defar PnP PCI Configurations Menu Reset Configuration Data Default Disabled This option is used to set whether the system is permitted to automatically distribute IRQ DMA and I O addresses when each time that the machine is turned on The setting values are Disabled and Enabled Resources Controlled By Default Auto ESCD This option is used to define the system resource control scheme If all cards you use support PnP then select Auto ESCD and the BIOS automatically distributes interruption resources If you install ISA cards not supporting PnP you will need to select Manual and manually adjust interruption resources in the event of hardware conflicts However since this motherboard has no ISA slot this option does not apply vo TRO Resources Press the lt Enter gt key then manuall
43. o 1 Install Driver Using this choice you can install all the drivers for your motherboard You should install the drivers in order and restart your computer after the drivers installed A IDE Driver B SiS SATA RAID optional C AGP Driver D VGA Driver optional E DirectX 9 0b F USB 2 0 Driver G Audio Driver H LAN Driver 2 Accessories Use this option to install additional software programs A SuperUtility a SuperLogo SuperLogo can display user designed graphics and pictures such as a company logo or personal photos thus making your PC more personalized and friendly b SuperStep Superstep is a powerful and easy to operate tool for overclocking You can quickly increase your CPU s working frequency through its user friendly interface It will enhance your CPU s performance and meet all kinds of DIY requirements c SuperUpdate SuperUpdate function can help to update the BIOS through internet directly B Adobe Reader C Norton Internet Security 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 4 Driver CD Introduction 3 Browse CD Click here to browse CD content 4 Homepage Click here to visit Foxconn motherboard homepage ET Note 1 Install the latest patch first if your OS is Windows XP or Win dows 2000 2 Follow the CD screen order to install your motherboard drivers Start to Install divers Select lt Install Driver gt and click to enter the install driver screen You can select t
44. ome other devices if the first second third boot devices failed The available setting val ues are Disabled and Enabled Swap Floppy Drive Default Disabled If you have two floppy diskette drives in your system this option allows you to swap the assigned drive letters The available setting values are Disabled and Enabled Boot Up Floppy Seek Default Disabled If this option is enabled BIOS will activate the floppy drive during the system boot and the drive s indicator will flash after the activation The magnetic head will move back and forth from A to B The available setting values are Disabled and Enabled Boot Up NumLock Status Default On This option defines if the keyboard Num Lock key is active when your system is started The available setting values are On and Off Gate A20 Option Default Fast This option is used to set up the A20 signal control necessary for access to the 1MB memory The available setting values are Normal and Fast 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Typematic Rate Setting Default Disabled If this option is enabled you can use the following two items to see the typematic rate and the typematic delay settings for your keyboard The avail able setting values are Disabled and Enabled Typematic Rate Chars Sec Default ei Use this option to define how many characters per second a held down key generated Typemati
45. rature will be automatically detected by the system CPU FAN Speed The CPU fan speed will be automatically detected by the system System FAN Speed The system fan speed will be automatically detected by the system Case Opened Warning Default Disabled This option is used to enable or disable case opened warning function The setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description Frequency Voltage Control Phoenix AwardBlOS CMOS Setup Utility FrequencyVoltage Contra GPU Glock Ratio Ra Auto Detect DINNZPCI Clk Enabled 2 Cpectrun Disabled tle Move Enter Select PU PD Walue Fi Save ESC Exit Hi General Help FS Previous Values Fo Pail Safe Defaults F7 Optinized Defaults Frequency Voltage Control Menu e CPU Clock Ratio Default based on CPU specifications This option is used to set the ratio of an unlocked CPU Using different CPU the setting values are different Note this option is invisible for locking frequency CPU Auto Detect DIMM PCI Clk Default Enabled This option is used to set whether the clock of an unused PCI DIMM slot will be disabled to reduce electromagnetic interference The setting values are Disabled and Enabled Spread Spectrum Default Disabled lf you enable spread spectrum it can significantly reduce the EMI Electro Magnetic Interference generated by the system Warning Be sure your
46. ry IDE secondary IDE FDD COA LFT Fort PC PIRQ A b1 Tl Hove Enter Select eeler H HIR Baue PS Previous Values Wake Up Events Enabled Disabled Enabled Enabled Enabled Hot Key Glick Disabled HA A p fienu Level kk Nr H Disabled Disabled Disabled ail Safe Defaults z OLUDLZE ESC Exit Fi General Help F7 Optini efaults PM Wake Up Events Menu IRQ 3 7 9 15 NMI Default Fnabled This option is used to enable or disable IRQ 3 7 9 15 NMI IRQ 8 Break Suspend Default Disabled This option is used to enable or disable IRQ8 break suspend RING Power Up Control Default Enabled lf this option is enable it allows the system to resume from a software power down or power saving mode whenever there is an incoming call to an in Stalled fax modem This function needs to be supported by the relevant hard ware and software The setting values are Disabled and Enabled MACPME Power Up Control Default Enabled This option is used to enable or disable the system to be waken up by onboard LAN PCIPME Power Up Control Default Enabled This option is used to enable or disable the system to be waken up by PCI card PS2KB Wakeup from S3 Default Hot Key This option is used to set which action will wake up PS 2 keyboard from 3 status The setting values are Any Key Hot Key Password PS2MS Wakeup from S3 Default Click This option
47. s for a PS 2 mouse PS 2 Keyboard Connector This purple 6 pin connector is for a PS 2 keyboard Serial Port COM1 This 9 pin COM1 port is for pointing devices or other serial devices Parallel Port Printer Port This 25 pin port connects a parallel printer a scanner or other devices VGA Port only for 661FX7MF The VGA Port is for output to a VGA compatible device USB 2 0 Ports These four Universal Serial Bus USB ports are available for connecting USB 2 0 1 1 devices LAN Connector This port allows connection to a Local Area Network LAN through a network hub 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 Installation Instructions 1394 Port optional This digital interface supports electronic devices such as digital cameras scan ners and printers Line in jack Line out jack Microphone jack When using a two channel sound source the Line out jack is used to connect to speakers or headphones the Line in port connects to an external CD player tape player or other audio device The Microphone jack is used to connect to the microphone L Line in Line out co j lt amp d Microphone etre When using a 6 Channel sound source connect the front speaker to the green audio output connect the surround sound speaker to the blue audio input connect the center soeaker subwoofer to the red Microphone input as shown in the follow ing figure Center Front
48. selection is right CPU overclock will be dangerous We will not be responsible for any damages caused 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 2 BIOS Description Load Fail Safe Defaults Press lt Enter gt to select this option A dialogue box will pop up that allows you to load the default BIOS settings Select lt Y gt and then press lt Enter gt to load the defaults Select lt N gt and press lt Enter gt to exit without loading The defaults set by BIOS set the basic system functions in order to ensure system stability But if your computer cannot POST properly you should load the fail safe defaults to restore the original settings Then carry out failure testing If you only want to load the defaults for a single option you can select the desired option the lt F6 gt key Load Optimized Defaults Select this option and press lt Enter gt and a dialogue box will pop up to let you load the optimized BIOS default settings Select lt Y gt and then press lt Enter gt to load the optimized defaults Select lt N gt and press lt Enter gt to exit without loading The defaults set by BIOS are the optimized performance parameters for the system to improve the performance of your system components However if the optimized performance parameters are not supported by your hardware devices it will likely cause system reliability and stability issues If you only want to load the optimized default for a single optio
49. setting to normal pins 2 and 3 locked together with the jumper cap 3 Turn the AC power supply back on Clear CMOS Jumper Q Warning 1 Disconnect the power cable before adjusting the jumper settings 2 Do not clear the CMOS while the system is turned on 661FX7MF 648FX7MF 648C7MF Series User Manual Chapter 2 Installation Instructions Starting up for the first time 1 After making all the connections replace the system case cover 2 Be sure that all switches are off 3 Turn on the devices in the following order a Monitor b External SCSI devices starting with the last device on the chain c System power 4 After applying power Led on the system front panel case lights up For ATX power supplies the system LED lights up when you press the ATX power switch If your monitor complies with green standards or if it has a power standby feature the monitor LED may light up or switch between orange and green after the system LED turns on The system then runs the power on tests While the tests are running the BIOS beeps or additional mes Sages appear on the screen If you do not see anything within 30 seconds from the time you turned on the power the system may have failed a power on test Check the jumper settings and connections or call your retailer for assistance 5 At power on hold down lt Delete gt to enter BIOS Setup Follow the instruc tions in Chapter 3 Powering off the computer 1 Using the OS shu
50. ss Enter gek Warning Disabled Li amp L Cache Enabled GN Ld Cache Disabled dien Ihreading Technology lEnabled L Cache ECC Checking Enabled Quick Power On Self Test Enabled First Boot Device Second Boot Device Third Boot Device Hoot Other Device Enabled Swap Floppy Drive Disabled Boot Up Floppy Seek Disabled Boot Up RE Status n Gate A20 Option Fast security Opt ion Setup APIG Rode Enabled APS Wersion Control For 0S 1 4 Tl Nove Enter Select PU PD Walue Fi8 Save ESC Exit Fi General we FS Previous Walues F Fail Safe Defaults F Optinized Default Advanced BIOS Features Menu CPU Feature Press enter to set the items of CPU feature Please refer to page 36 Hard Disk Boot Priority This option is used to select the priority for HDD startup After pressing lt Enter gt you can select the HDD using the lt PageUp gt lt PageDn gt or Up Down arrow keys and change the HDD priority using lt gt or lt gt you can exit this menu by pressing lt Esc gt Virus Warning Default Disabled Allows you to choose the VIRUS warning feature for IDE hard disk boot sector protection If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on screen and an alarm will beep The available setting values are Disabled and Enabled Note Such function provides protection to the start up sector only it does not protect the e
51. t down function lf you use windows 98 ME 2000 XP click the Start button click Shut Down then click the OK button to shut down the computer The power supply should turn off after Windows shuts down 2 Using the dual function power switch While the system is ON pressing the power switch for less than 4 sec onds puts the system to sleep mode or to soft off mode depending on the BIOS setting Pressing the power switch for more than 4 seconds lets the system enter the soft off mode regardless of the BIOS setting 661FX7MF 648FX7MF 648C7ME Series User Manual napter This chapter tells how to change system settings through the BIOS Setup menus Detailed descriptions of the BIOS parameters are also provided You have to run the Setup Program when the following cases occur 1 An error message appears on the screen during the system POST process 2 You want to change the default CMOS settings This chapter includes the following information Get Ze Ze Ze Ze Ze Ze Ze Ze Ze Ze Ze Ze Ze Ze Ze Enter BIOS Setup Main Menu Standard CMOS Features BIOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP PCI Configurations PC Health Status Frequency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor User Password Save amp Exit Setup Exit Without Saving Chapter 3 BIOS Description Enter BIOS
52. t password is entered you will not be permitted to continue Under the menu Advanced BIOS Features Setup if you select Setup from the security Option you will be prompted to enter a password only when you enter the CMOS setting program Save amp Exit Setup When you select this option and press lt Enter gt the following message will appear in the center of the screen SAVE to CMOS and EXIT Y N Y Press lt Y gt to save your changes in CMOS and exit the program press lt N gt or lt ESC gt to return to the main menu Exit Without Saving If you select this option and press lt Enter gt the following message will appear in the center of the screen Quit Without Saving Y N N Press lt Y gt to exit CMOS without saving your modifications press lt N gt or lt ESC gt to return to the main menu 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter The utility CD that came with the motherboard contains use ful software and several utility drivers that enhance the motherboard features This chapter includes the following information Utility CD content Start to install drivers Chapter A Driver CD Introduction Utility CD content This motherboard comes with one Utility CD To begin using the CD simply insert the CD into your CD ROM drive The CD will automatically display the main menu screen FOXCONN Utility ch Fa SIS SET VES SCHAN d K baa P e po
53. y set IRQ resources PCI VGA Palette Snoop Default Disabled lf you use a non standard VGA card use this option to solve graphic accelera tion card or MPEG audio card problems e g colors not accurately displayed The setting values are Disabled and Enabled 661FX7MF 648FX7MF 648C7ME Series User Manual Chapter 3 BIOS Description PC Health Status enix AwardBlOS CMOS Setup Utility PG Health Status CPU Fan Control Disabled Iten Help Enu LEVE Shutdown Temperature Disabled CPU Vcore Lzy LAU eni em Speed Kg FAHI Speed Case Opened warning Disabled Suste GPU FAH Cun Tl4 Nove Enter Select PU PD Walue Fi Save ESC Exit Fi General Help FS Previous Values fo Fail Safe Defaults F Optinized Defaults PC Health Status Menu CPU Fan Control Default Disabled This option is used to disable or enable CPU fan control function The setting values are Enabled Disabled Shutdown Temperature Default Disabled This option is used to set the system temperature upper limit When the temperature exceeds the setting value the motherboard will automatically cut off power to the computer The setting values are and 60 C 140 F 65 C 149 F 70 C 158 F Disabled CPU Vcore 3 3v 5v 12v The current voltages will be automatically detected by the system CPU Temp The current CPU temperature will be automatically detected by the system System Temp The system tempe
Download Pdf Manuals
Related Search