Samsung SR-8855
Contents
1. 4 F Install the batteries into the After inserting the tip of remote control as shown the cover into the slot by the figure below If the push the other end to batteries are installed with close it until it clicks into the wrong polarity the place remote control will not work x Specification AAA type batteries Assembling the cleaner NAME OF EACH PART Status Display Window YANVATO JHL ONITIEINASSV Z0 DISPLAY PART 1 Number Display Shows the timer display progress status and error codes using numbers letters and graphics 2 Battery Level Indicator Charging Shows the charging progress in 3 steps In Use Shows the battery charge level The battery charge level is reduced by each level from FULL while operating When the battery is fully discharged one level will flash to display LO 3 Scheduled Cleaning When cleaning is scheduled the Scheduled Cleaning icon is lit 4 Daily When daily cleaning is scheduled the Daily icon is lit 5 Recharging This icon turns on when the cleaning robot returns to the charger station to charge its battery 6 Cleaning Mode Display Each time the Cleaning Mode button is pressed the corresponding cleaning mode is displayed a Auto Mode This icon turns on when Auto cleaning mode is selected b Spot Mode This icon turns on when Spot cleaning mode is selected c Max Mode This icon turns on when Max cleaning mode is sele2. Robotic vacuum cleaner is for domestic use only Do not use it in the following locations Attics basements warehouses industrial buildings separate rooms distant from the main building locations exposed to wet or damp conditions such as bathrooms or wash rooms and narrow and highly situated locations such as tables or shelves Critical damage abnormal operation and breakage may occur when used in these locations Open all doors to clean all rooms When a door is closed the robotic vacuum cleaner will not be able to enter that room However make sure to close the doors to the main entrance the veranda and the bathroom and any other rooms where the robotic vacuum cleaner may fall to a lower floor For carpets with long tassels fold the tassels under the carpet Unfolded tassels may result in critical damage to the carpet and the machine itself as they get caught in the driving wheel or the power brush When the cliff sensor is polluted the robotic vacuum cleaner may be in danger of falling down the stairs This may cause personal injury and critical damage to the product To prevent risk install the VIRTUAL GUARDs Fence Mode setting in front of dagerous areas Clean the sensor window and camera Safety information _7 NOILVWHOJNI ALSAVS 10 safety information BEFORE USE CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION Remove
3. Press the button To turn it off press and hold the amp button down for 3 seconds or longer Lift up the robotic vacuum cleaner and manually dock the robotic vacuum onto the charger to charge it Replace the batteries in the remote control AAA type SNILOOHSATENOUL SO Robotic vacuum cleaner stopped operating while cleaning Is the battery level flashing only one level and is LO displayed in the display panel Has the robotic vacuum cleaner become hooked on wires on the floor Is the robotic vacuum cleaner stuck to the floor where there is a height difference The driving wheel is lifted Is there a thin towel cloth wrapped around the driving wheel Is the robotic vacuum cleaner stuck on the doorsill Lift up the robotic vacuum cleaner manually dock the robotic onto the charger to charge it Turn off the Power Switch and remove the wires Turn off the Power Switch and move the cleaning robotic vacuum to another place to clean Turn off the Power Switch and remove the thin towel Turn off the Power Switch and move the robotic vacuum cleaner to another place to clean The suction power is weak while cleaning Check whether the dust bin is full of dust Check whether the suction inlet is clogged by foreign substances Check whether the filter is clogged Stop the robotic vacuum cleaner and empty the dust bin Turn off the Power Switch
4. Before operating this unit please read the instructions carefully English For indoor use only imagine the possibilities Thank you for purchasing a Samsung product To receive a more complete service please register your product at www samsung com register SRB Safety information SAFETY INFORMATION e Before operating the appliance please read this manual thoroughly and retain warnine it for your reference e Because these following operating instructions cover various models the WARNING Characteristics of your vacuum cleaner may differ slightly from those described in this manual CAUTION WARNING SYMBOLS USED Indicates that a danger of death or serious injury exists WARNING CAUTION Indicates that a risk of personal injury or material damage exists OTHER SYMBOLS USED Explains terms to help users understand how use the product properly NOTE 2_ Safety information safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR ROBOTIC VACUUM CLEANER Unplug from outlet when not in use and before conducting maintenance WARNING to reduce the risk of fire electric shock or injury GENERAL Use only as described in this manual Do not operate the robotic vacuum cleaner or charger if it has been damaged in any way If the cleaner is no
5. If the robotic vacuum cleaner is separated from the charger the battery is automatically discharged Operating the cleaner _21 HANVJ7O SHL DNILVH3dO 0 Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER CHARGING When the product is initially purchased the battery is fully discharged and you must charge the robotic vacuum cleaner manually 1 After aligning the charge pins of the main unit with the charge pin of the charger station press the main unit until you hear a Recharging power sound from the charger The Charging Lamp turns green 2 Check the charge status of the robotic vacuum cleaner When charging starts the battery level indicator and H will be displayed in sequence in the display panel When charging is complete the battery level indicator and FULL will be displayed in the display panel Charging Fully charged lt Charge display gt D E When the battery level display flashes TE while cleaning the robotic vacuum a Ca co cleaner stops vacuuming and a automatically charges itself at the charger Charge Charging Required complete charging m When the battery level flashes and LO is displayed while cleaning robotic vacuum cleaner cannot be operated by the remote control or the buttons on the main unit In this case directly carry the robotic vacuum cleaner to the charger to charge the battery This is when the battery
6. If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp ASTA approved to BS 1362 fuse is fitted in the carrier contained in the plug If for any reason the plug is cut off it must be disposed of as it is an electric shock hazard should it be inserted into a 13 amp socket 4_ Safety information Contents SAFETY INFORMATION 06 Power related O7 Before use 10 Inuse 11 Cleaning and maintenance PRODUCT FEATURES 13 Product Features ASSEMBLING THE CLEANER 15 Components 16 Name of each part OPERATING THE CLEANER 20 Installing robotic vacuum cleaner al 20 Installation order 20 Turning the power switch on or off 21 Installing the charger 22 Charging 23 About the battery 24 Setting the Time 25 Installing the VIRTUAL GUARD 27 Using robotic vacuum cleaner 27 Starting stopping cleaning 28 Recharging 29 Auto cleaning 30 Spot cleaning 31 Max cleaning 32 Manual cleaning 33 Edge cleaning 34 Scheduled cleaning 35 Setting daily cleaning MAINTAIN TOOLS AND FILTER 36 Cleaning robotic vacuum cleaner 36 Please keep the cleaning and maintenance methods in mind 36 Cleaning the sensor window and the camera 37 Emptying the dust bin quickly 37 Cleaning the dust bin and the filter 39 Cleaning the power brush 41 Cleaning the edge cleaning side rotating brush 42 Cleaning the driving wheel TROUBLESHOOTING 43 Checklist before svc calls 45 Troubleshooting for Error Co
7. In Spot cleaning mode the robotic vacuum cleaner cleans an area with a length of 1 5m and a width of 1 5m When cleaning is completed the robotic vacuum cleaner will display End Stop and Stand by When the robotic vacuum cleaner is docked with the note Charger station spot cleaning is not supported 30_ Operating the cleaner When cleaning is complete Operating the cleaner USING THE ROBOTIC VACUUM CLEANER MAX CLEANING The robotic vacuum cleaner automatically moves and cleans until the battery runs out and the battery level flashes only one level E If cleaning begins when the robotic vacuum cleaner is docked with the charger station the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving E f the battery level becomes low while cleaning the robotic vacuum cleaner automatically returns to the charger station and resumes cleaning after charging the battery Number of resumed cleaning operations Once YANV3T19 SHL DNILVH3dO 0 Set the mode Cancel the mode While cleaning About the Resume Cleaning function Note e If the robotic vacuum cleaner judges cleaning to be complete resume cleaning is not performed e If you move the robotic vacuum cleaner while it is being charged or
8. 2 Set the fence length using the distance control switch 8 Charger VIRTUAL GUARD 3 Install the VIRTUAL GUARD at the entrance of the room to be cleaned Install the VIRTUAL GUARD so that the distance Distance Detection Sensor detection sensor can form an invisible barrier that the robotic vacuum cleaner cannot cross 30cm B e When not using the VIRTUAL GUARD turn the power off Auer virtual do Nove When not using the robotic vacuum cleaner for guard i i long periods of time separate the batteries to avoid R A discharging them x Since an invisible barrier is formed e If the Mode Power button does not work it indicates ee that the batteries have worn out In this case replace the aa z batteries Specifications Type D LR20 alkaline batteries VIRTUAL GUARD installing the e You can additionally purchase a VIRTUAL GUARD from IRTUAL GUARD within 30 cm of Samsung Electronics customer care Co Ltd the outside walls is recommended About the IrDA sensor CAUTION e The infrared signal transmission may not be smooth in locations exposed to halogen lamps or in outdoor locations e Robotic vacuum cleaner uses 3 types of infrared devices and a device may not work in front of another device with a higher priority e When controlling the robotic vacuum cleaner with the remote control the robotic vacuum cleaner may cross the virtual fence of the VIRTUAL GUARD or run against an obstacle because the remote control sig
9. The 3 Cliff sensors detect downward steps such as stairs or the front door threshold to prevent robotic vacuum cleaner from falling down stairs 14_ Product Features When the robotic vacuum cleaner is lifted up while cleaning the driving wheels power brush suction motor and side rotating brush are stopped autonati all by sensor Assembling the cleaner COMPONENTS m Others Components m Main Body m Remote Control m Charger Station AAA Tvpe Batteries EED ka J Ss User Menuel VIRTUALGUARD Spare Filter Cleaning Brush 2 Battery 9 Loss JN p Remote Control Spare Edge Cleaning Side Cradle Brush 2 Spare Power Brush Assembling the cleaner _15 HANV310 JHL ONIMIEIWASSV 20 Assembling the cleaner NAME OF EACH PART Main unit Dust Outlet Operating Button Display Panel Camera VIRTUAL Obstacle Sensor GUARD Sensor 4 F q Remote Control VIRTUAL GUARD a Sensor Sensor Obstacle Sensor Bumper Sensor Dust Bin Eject Button Dust Bin Dust Outlet Remote Control Poe A Sensor Cliff Sensor Side Brush Driving Wheel Charge Pin Battery Cover Cliff Sensor Power Brush DA Power Brush Charge Pin Wi Cover Roller SQ l l Power Switch i Driving Wheel Cliff Sensor 16_ Assembling the cleaner Assembling the cleaner NAME OF EACH PART Charger Station Power
10. and remove the foreign substances on the suction inlet Clean the filter well Troubleshooting _43 jrouplesnooting CHECKLIST BEFORE SVC CALLS SYMPTOM CHECKLIST MEASURE TO TAKE Robotic vacuum cleaner cannot find the charger Check whether the power plug of the charger is plugged correctly into the outlet If there are any obstacles within a range of about 1m in front of the charger and about 0 5m range to the left and right of the charger you should remove the obstacles If there are any foreign substances on the change pin wipe them off with a dry towel Is the VIRTUAL GUARD installed near the charger Is the distance detection sensor of the VIRTUAL GUARD facing the charger Move the VIRTUAL GUARD to another place so that the robotic vacuum cleaner can charge automatically Change the direction of the VIRTUAL GUARD or set the distance to an appropriate value Robotic vacuum cleaner passes Are the batteries of the VIRTUAL GUARD worn out Replace the batteries 2 type D LR20 alkaline through the batteries VIRTUAL GUARD e Is the VIRTUAL GUARD set to e Set the VIRTUAL GUARD to Guard Fence virtual wall mode virtual door mode e Is the Mode lamp turned off e Check if the VIRTUAL GUARD is turned off and then set the VIRTUAL GUARD to a desired mode The battery e Are you using manganese drycell Replace the batteries with new usage time of the bat
11. charger to high temperatures or allow moisture or humidity of any kind to come into contact with the charger Safety information _3 Safety information ROBOTIC VACUUM CLEANER Do not pick up hard or sharp objects such as glass nails screws coins and etc Do not use without a filter in place When servicing the unit never put fingers or other objects into the fan chamber in case the unit accidentally turns on Do not put any objects into openings Do not use with any openings blocked keep openings free of dust lint hair and anything that may reduce air flow Do not pick up toxic materials chlorine bleach ammonia drain cleaner etc Do not pick up anything that is burning or smoke such as cigarettes matches or hot ashes Do not use to pick up flammable or combustible liquids such as gasoline nor use on areas where they may be present Do not use robotic vacuum cleaner in an enclosed space filled with vapours given off by oil based paint paint thinner moth proofing substances flammable dust or other explosive or toxic vapours Leaks from battery cells can occur under extreme usage or temperature conditions If the liquid gets on skin wash quickly with water If the liquid gets into the eyes flush them immediately with clean water for a minimum of 10 minutes Seek medical attention SAVE THESE INSTRUCTIONS This vacuum cleaner is intended for household use only FOR RESIDENTS OF THE UNITED KINGDOM ONLY
12. small objects or brittle items from the area to be cleaned in advance Make sure to clear any objects before cleaning Make sure to remove fragile items such as china glass objects flowerpots etc Robotic vacuum cleaner does not recognize coins rings or other valuable items such as jewelry Remove objects scattered on the floor before cleaning Robotic vacuum cleaner is designed to detect obstacles 5cm away from it Bath towels pads in front of bathrooms and sinks entrances utility rooms power cords table cloths or belts can become entangled in the driving wheel or power brush This can cause objects to fall from the table Inform all family members or relevant parties to be cautious before cleaning or when using the Scheduled Cleaning Mode Robotic vacuum cleaner may run into children causing them to fall Ensure that children do not step or sit on the robotic vacuum Children may fall and injure themselves or critical damage may occur to the product When a child or pet is left alone make sure to turn off the Power Switch of the robotic vacuum cleaner Robotic vacuum cleaner may attract their attention When the rotating wheel or brush catches fingers feet clothing or hair this may result in injury If a child or pet is in the way of the robotic vacuum cleaner it may be identified as an obstacle and the area may not cleaned When the Power Switch i
13. then reassemble the side rotating brush Letter R is carved at the right side rotating brush Because the side rotating brush easily attracts hair and other foreign substances note Make sure to clean it frequently Excessive foreign substances on the side rotating brush can damage the brush Maintain tools and filter 41 Maintain tools and titer CLEANING THE ROBOTIC VACUUM CLEANER CLEANING THE DRIVING WHEEL You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic E f the robotic vacuum cleaner suddenly starts to zigzag there may be foreign substances stuck on the driving wheel 1 When cleaning the driving wheel place a soft cloth on the floor and flip the main unit placing it down carefully 2 Check for foreign substances and remove them using a stick or a pair of blunt nippers if necessary 42_ Maintain tools and filter trouplesnooting CHECKLIST BEFORE SVC CALLS SYMPTOM CHECKLIST MEASURE TO TAKE Robotic vacuum cleaner does not operate at all before cleaning Is the dust bin assembled Is the Power Switch turned on e Is cleaning mode fa in the display panel turned on Is the battery level flashing only one level and is LO displayed in the display panel Robotic vacuum cleaner will not operate when the battery in the remote control is depleted Install the dust bin Turn on the Power Switch
14. ING THE POWER SWITCH ON OR OFF To use the robotic vacuum cleaner you must turn the Power Switch on If you turn the Power Switch off all settings will be reset 1 Turn over the main unit and turn the Power Switch on If the icons are not turned on it indicates that the battery charge is depleted In this case dock the robotic vacuum cleaner to the charger station after turning the Power Switch on The configured time may be different from the current time If the configure time is incorrect set the time to the current time If the Power Switch is turned off the robotic vacuum cleaner will not be charged caution even if it is docked with the charger station 20_ Operating the cleaner Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER INSTALLING THE CHARGER 1 Install the charger on a flat surface 2 There should be no obstacles 0 5m to the left and right and within 1 m of the front 3 Install the charger in a location where it can be easily accessed by the robotic vacuum cleaner 4 Arrange the power cord along the wall 5 When the floor is made of wood install the charger in the same direction as the grain of the wood BE Alwavs keep the power cord of the charger plugged into the power outlet If no power is supplied to the charger the robotic vacuum will not be able to find the charger and will not be able to charge automatically
15. Lamp Charging Lamp Remote Control Holder Charge Pin Vents Catching Sill YANV3AT9 JHL NNANWASSY 20 Distance Detection Sensor Main Body Detection Mode Power Button Sensor Distance Control Switch m Installing the batteries Batteries are not supplied with the product You have to purchase the batteries separately Install the alkaline batteries type D before use Lift the cover of the Install the batteries into the After inserting the tip of VIRTUAL GUARD while VIRTUAL GUARD as shown the cover into the slot pressing the locking tab by the figure below If the push the other end to batteries are installed with close it until it clicks into the incorrect polarity the place VIRTUAL GUARD will not work x Specification Alkaline Type D LR20 batteries Assembling the cleaner _17 Assembling the cleaner NAME OF EACH PART Directional Buttons moving backwards is not supported Manual Edge m Installing the batteries Remote Control Recharging Auto Spot Max Spot Start Stop Timer Dailv Clock SAMSUNG Batteries are not installed in the remote control when purchasing the product Install the batteries tvpe AAA before use Lift the batterv compartment cover at the back of the remote control while pressing the locking tab 18 Assembling the cleaner
16. ROBOTIC VACUUM CLEANER 4 Wipe the dust from the filter and the dust bin k You can wash them with water 5 Install the filter into the dust bin Make sure that the grid pattern of the filter is facing downwards It cannot be installed in the wrong direction 6 Close the dust bin cover and install it into the main unit Structure of the Dust Bin Dust Bin Eject PUSH Button Filter Sas Dust Outlet Cover Dust Bin 38_ Maintain tools and filter Maintain tools and iter CLEANING THE ROBOTIC VACUUM CLEANER CLEANING THE POWER BRUSH You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic vacuum e Because the dust in the dust bin may come out caution Separate the dust bin first before cleaning the power brush 1 Separate the dust bin by pressing the Dust Bin Eject PUSH button 431114 ANY STOOL NIVLNIVIN 70 2 After checking whether there are any foreign substances press the hook that is fixing the brush cover to separate it 3 Lift the power brush up from the main unit 4 Remove any foreign substances such as long hairs or strings wrapped around the power brush using a cleaning brush or a vacuum cleaner 5 When cleaning is complete fix the Power Switch side of the power brush first and then fix the other side of the brush in the same way Maintain tools and filter _39 Maintain tools and
17. and cleaning mode icons are turned on Turning the power off Remote control Press the Power button Main unit Press and hold the button down for 3 seconds All icons except for the battery level indicator are turned off Starting Remote control Press the Auto Spot Max Manual or Edgebutton Main unit Select Auto Spot Max Manual Edge Ka mode by using the 9 button and then pressing the button s When cleaning begins the robotic vacuum cleaner starts to move x Pressing the e button without selecting cleaning mode starts to perform the Auto mode cleaning angaa Stopping l To stop press the remote control or main unit button When cleaning is stopped the robotic vacuum cleaner stops Operating the cleaner _27 HANV31O JHL DNILVH3dO 0 Operating the cleaner USING THE ROBOTIC VACUUM CLEANER RECHARGING You can have the robotic vacuum cleaner return to the charger to charge the battery by using the Recharging button m When the robotic vacuum cleaner is operating press the button to cancel the operation and press the Recharging button 1 Press the Recharging button The main unit icon f is turned on and the robotic vacuum cleaner will return to the charger 2 To stop the robotic vacuum cleaner while it is returning to the charger press the 69 button 3 To test the auto charge function press the R
18. ay water thinner benzene etc directly onto the main unit of robotic vacuum cleaner m Lightly wipe the sensor window or camera using a soft cloth Display Panel Front Sensor window Front Sensor Window and Camera Cliff Sensor Window Rear Sensor Window 36_ Maintain tools and filter Maintain tools and iter CLEANING THE ROBOTIC VACUUM CLEANER EMPTYING DUST QUICKLY m You can easily empty the dust bin using a normal vacuum cleaner without separating the dust bin 1 Open the dust outlet cover 2 If you hold the air inlet of the vacuum cleaner to the dust outlet it will vacuum the dust directly from the dust bin 431114 ANY STOOL NIVLNIVIN vO CLEANING THE DUST BIN AND THE FILTER First empty the dust bin before cleaning it m When separating the dust bin take care not to spill the dust out of the dust bin m Empty the dust bin in the following cases 1 When dust has accumulated inside the dust bin 2 When the suction power suddenly becomes weak 3 When the noise suddenly increases 1 Press the Dust Bin Eject PUSH button and pull the dust bin to separate the dust bin 2 Separate the dust bin cover by pulling it in the direction of the arrow in the figure 3 Separate the filter from the dust bin by pulling it in the direction of the arrow in the figure Maintain tools and filter _37 Maintain tools and titer CLEANING THE
19. cted d Manual Mode This icon turns on when Manual cleaning mode is selected e Edge Mode Ed 9B is on when Edge cleaning mode is selected BUTTON PART 7 Start Stop Press to start stop cleaning 8 Cleaning Mode l Press to select a cleaning mode After selecting a cleaning mode press the 6 button to start cleaning 9 Timer Dailv Press to set a scheduled or daily cleaning 10 Recharging When this button is pressed the Recharging icon is turned on and the cleaning robot will return to the charger station to charge its battery Assembling the cleaner _19 Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER INSTALATION ORDER 1 Turning the Power Switch on or off To use the robotic vacuum cleaner you must turn on the Power Switch at the bottom of the main unit 2 Installing the Charger To charge the robotic vacuum cleaner you must first install the charger Since the battery is discharged when the product is purchased you must fully charge the battery before use 3 Charging the Battery You should charge the battery completely before using the robotic vacuum cleaner 4 Setting the Time You should set the time to use the scheduled and daily cleaning options 5 Installing the VIRTUAL GUARD You can confine the robotic vacuum cleaner to a particular section by using Fence virtual wall mode or clean several sections one by one using Guard virtual door mode TURN
20. cuum cleaner immediately turn off the Power Switch and call NOTE the customer care center Robotic vacuum cleaner may not be able to continue its operation if it is stuck at the entrance or veranda doorsill Robotic vacuum cleaner stops operating for safety reasons if it cannot move for more than 5 minutes To resume operating turn the Power Switch off and then on again after moving it to a location where it can continue cleaning 10_ Safety information Safety information IN USE B NOTE NOTE Robotic vacuum cleaner cannot completelv clean locations that it cannot reach such as corners and spaces between sofas and walls Please clean these locations occasionally Dust clusters may remain after cleaning when the robotic vacuum cleaner fails to pick up dust clusters that were formed while cleaning In this case sweep up the dust with another cleaning tool CLEANING AND MAINTENANCE CAUTION CAUTION CAUTION WARNING When cleaning the product do not spray water directly onto the exterior or wipe it with a volatile material such as benzene thinner or alcohol This may result in critical damage to the product Do not forcefully press the bumper on the robotic vacuum cleaner If the bumper sensor gets damaged the robotic vacuum cleaner may bump into walls or furniture The unit must not be disassembled or reconstr
21. des PRODUCT SPECIFICATION 46 Product specification Contents 5 Safety information POWER RELATED Do not bend the power cord forcefully or place a WARNING heavy object on it that could break it This may result in fire or electric shock Make sure to remove any dust or water from the WARNING POWer plug Failing to do so may result in a malfunction or electric shock Do not pull the power plug by the cord or touch the WARNING Plug with wet hands This may result in fire or electric shock Do not use multiple plugs in a single socket warning Do not leave the cord lying exposed on the floor This may result in fire or electric shock Do not use a damaged power cord plug or a loose WARNING POWer outlet This may result in fire or electric shock 6_ Safety information Safety information BEFORE USE CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION Before activating the robotic vacuum cleaner make sure that the dust bin is assembled If the dust bin is not inserted robotic vacuum cleaner will not operate Never use robotic vacuum cleaner in locations with combustible material such as Locations with candles or desk lamps on the floor Locations with unattended fires fire or embers Locations with gasoline distilled alcohol thinner ashtrays with burning cigarettes etc
22. during the cleaning the Robot vacuum Cleaner reduces its speed to minimize the bumping impact and the Bumper Sensor also helps it lower the bumping impact It cleans the corners by reaching to them as close as possible This Robotic vacuum Cleaner is a touching type cleaner The robotic vacuum cleaner will move by itself and automatically clean the house until cleaning is completed once E f cleaning begins when the robotic vacuum cleaner is docked with the charger station the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving YANV3T19 JHL ONILVYAdO 0 m f the battery level becomes too low while cleaning the robotic vacuum Cleaner will automatically return to the charger station and resume cleaning after charging its battery Number of cleaning operations resumed Once Set the mode I cure Peal at a g a Timer jin Cancel the mode While cleaning E About the Resume Cleaning function note e If the robotic vacuum cleaner judges cleaning to be complete resume cleaning is not performed e If you move the robotic vacuum cleaner while it is being charged or press a button robotic vacuum cleaner judges cleaning to be complete cleaning is not resumed Do not move the robotic vacuum cleaner while it i
23. e e What is ceiling shape recognition a Visionary mapping Se This function recognizes the shape of the ceiling using the camera on top to identify the area to be cleaned and determines the best wav to pass over and clean everv section of the floor DELICATE CLEANING OF EVERV CORNER Since the robotic vacuum cleaner cleans the floor in a sequential wav 14 along the map determined by the ceiling shape recognition function it cleans every corner of the floor VARIOUS CLEANING MODES Various cleaning modes are provided to meet all your needs 1 zj 2 Approximately 1 5 m 3 an il Auto Mode l e C Po ee Cleans all rooms automatically 5 a 2 SPOT MODE KI ye 8 B i Cleans a localized area intenselv It i ll U 4 l IL can be used to clean bread or cookie G L crumbs 115 6 7 3 Max Mode Runs until the battery is nearly i depleted i 2 l 4 Manual Mode E You can clean the floor manually by moving the cleaning robot Te 5 Edge Mode is oe When the Obstacle Sensor detects an obstacle during the cleaning m the Robot Cleaner reduces its speed
24. echarging button when the robotic vacuum cleaner is less than 1 5m from the charger Manual Edge Timer Daily lack OOO Troubleshooting when the robotic vacuum cleaner does not return to the charger e Check the installation of the charger When the charger is in a location where the charger cannot guide the robotic vacuum cleaner to the charger When the charger is more than 5m away from robotic vacuum cleaner It may require a longer time for the robotic vacuum cleaner to return to the charger e Manually charge the robotic vacuum cleaner in the following cases When the charger is installed in a corner When the battery is fully discharged When the robotic vacuum cleaner is trapped by an obstacle furniture etc When the robotic vacuum cleaner cannot pass over the doorsill to the location where the charger is installed The height of the doorsill should be about 1cm or less 28_ Operating the cleaner aw i Timer Recharging Daily Operating the cleaner USING THE ROBOTIC VACUUM CLEANER AUTO CLEANING The robotic vacuum cleaner will move by itself and automatically clean the house until cleaning is completed once E If cleaning begins when the robotic vacuum cleaner is docked with the charger station the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving E f the battery level becomes too low wh
25. g i Cleaning mode Edge Scheduled Setting Daily Auto Spot Max Manual Cleaning Charging time About 120 minutes Cleaning time on the basis of hard floor About 90 minutes Cleaning method Ceiling shape recognition Main unit button type Touch type This Vacuum cleaner is approved the following Electromagnetic Compatibility Directive 2004 108 EEC Low Voltage Directive 2006 95 EC Product specification _47 NOILVOIsaIDAdS LONGOYd 90 If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center Country Customer Care Center Web Site U K 0845 SAMSUNG 7267864 www samsung com SOUTH AFRICA O860 SAMSUNG 726 7864 www samsung com DJ68 00518B REV 0 0
26. ile cleaning the robotic vacuum cleaner will automatically return to the charger station and resume Cleaning after charging its battery Number of cleaning operations resumed Once NOTE CAUTION HIANV37O JHL DNILVH3dO 0 Auto Set the mode Cancel the mode About the Resume Cleaning function e If the robotic vacuum cleaner has evaluated that cleaning is complete the resume cleaning function is not performed e If you move the robotic vacuum cleaner when it D is being charged or press a button the robotic Belay Wren vacuum cleaner judges cleaning to be complete and does not resume cleaning When cleaning is complete Do not move the robotic vacuum cleaner when it is cleaning or press a button while it is cleaning Otherwise the robotic vacuum cleaner judges cleaning to be complete and starts cleaning again from the beginning Operating the cleaner _29 Operating the cleaner USING THE ROBOTIC VACUUM CLEANER SPOT CLEANING You can conveniently clean a specific area that has aa lot of cookie crumbs dust and etc E Move the robotic vacuum cleaner to the location where you want to perform a spot clean About 1 5m About 1 5m Set the mode Spot Mode Start eat Stop EAA AN Cancel the mode Start Stops
27. is completely discharged P e When the product is initially purchased it will take about 120 minutes to fully charge the battery and will run for about 90 minutes e When charging the battery while the battery is over heated the charging time can increase e Measures to take when charging is not smooth When the robotic vacuum cleaner cannot be automatically charged check the following Turn the Power Switch at the bottom of the robotic vacuum cleaner off and on Reset Re plug the power of the charger Reset Check whether there are any foreign substances on the charge connector and wipe the charge connector on the main unit and the charger with a dry cloth Check whether there are objects near the charger that are strong reflectors e When separating the robotic vacuum cleaner from the charger it will discharge naturally Charge the robotic vacuum cleaner through the charger if possible When leaving your home unattended for a long period of time due to a business trip travelling etc turn off the Power Switch of the robotic vacuum cleaner and unplug the power of the charger to store them NOTE 22_ Operating the cleaner Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER ABOUT THE BATTERY m The robotic vacuum cleaner is powered by an environment friendly Nickel Metal Hydride NiMH rechargeable battery and an over charge prevention function guarantees an extended life time m The battery war
28. iter CLEANING THE ROBOTIC VACUUM CLEANER 6 After inserting the 3 tips at the top of the cover push the other end in until it clicks into place e To prevent the robotic vacuum cleaner from becoming clogged be careful not to caution Vacuum tooth picks or cotton swabs e When removing foreign substances becomes difficult contact a customer care center e Because the power brush vacuums the dust on the floor long strings or hair can become wrapped around the brush Check and clean the power brush regularly 40_ Maintain tools and filter Maintain tools and iter CLEANING THE ROBOTIC VACUUM CLEANER CLEANING THE EDGE CLEANING SIDE ROTATING BRUSH You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic vacuum 1 Check whether the side rotating brush is bent or whether there are any foreign substances stuck on the brush 43 11114 ANY STOOL NIVLNIVIN 70 2 Wearing rubber gloves wrap the side rotating brush with a cloth using hot water for about 10 seconds and wipe it on the cloth 3 Turning the side rotating brush repeat the procedures in Step 2 4 If hair or string is wrapped between the main unit and the side rotating brush undo the screw of the side rotating brush using a driver to remove it When reassembling the brush check the L mark on the edge cleaning side rotating brush and the L mark on the main unit and
29. le The current time 07 00 a m Enter Daily Cleaning The desired cleaning start Timer Dail mode and confirm that LT po 1 the configured time is time 09 30 a m ix G correct Check the daily am UU reservation time IS Ls HANVJ1O JHL DNILVH3dO 0 Start the setting TimeriDail mer B Dai Set the hour Confirm the hour TimeriDail Dai l Set the minutes Complete the settings Timer Timer Daily AN a R A U T JILI Cancel the settings Sto gt ae When completing the settings and you press the button instead of the Delay note Daily button Daily Cleaning mode is exited Daily The icon is turned off Operating the cleaner _35 Maintain tools and titer CLEANING THE ROBOTIC VACUUM CLEANER PLEASE KEEP THE CLEANING AND MAINTENANCE METHODS IN MIND m When the Power Switch is damaged please contact the service agent so that it does not cause any accidents m Do not use any means or mechanical devices not installed by the manufacturer that could accelerate the deformation of the robotic vacuum cleaner m Always turn off the power switch at the bottom of the main unit before cleaning the robotic vacuum The robotic vacuum cleaner could operate suddenly and cause an injury CLEANING THE SENSOR WINDOW AND THE CAMERA You must turn off the Power Switch at the bottom of the main unit before cleaning the robotic vacuum Never spr
30. nal has a higher priority than the VIRTUAL GUARD signal e When using the robotic vacuum cleaner in a small location or at a close distance it may malfunction due to interference of the infrared signals e Install the VIRTUAL GUARD away from the charger as auto charging may be interrupted if the VIRTUAL GUARD is near the charger e If the fence length is set to a value longer than the required distance the robotic vacuum cleaner may fail to clean properly Set the fence length to an appropriate value using the distance control switch e If more than one robotic vacuum is used simultaneously they may malfunction due to interference of the infrared signals e Turn the VIRTUAL GUARD in another direction or set the fence length to an appropriate value if the distance detection sensor of the VIRTUAL GUARD faces the charger as it may interrupt auto charging Infrared Signal Priority Remote Control Virtual guard Charger 26_ Operating the cleaner Operating the cleaner USING THE ROBOTIC VACUUM CLEANER STARTING STOPPING CLEANING You can run or stop all robotic vacuum functions m Each robotic vacuum function only runs when the Power Switch is turned on m When the robotic vacuum is operating press the E button to cancel the operation and select a function Turning the power on Remote control Press the Power button Main unit Press the 5 button The main unit buttons battery level indicator
31. nsor Set the distance to restrict the access of robotic vacuum cleaner from the VIRTUAL GUARD using the distance control switch S 4m 2 3m 1 2m Switch Setting Max e Short About 1 2m The distance detection sensor ee Medium About 2 3m forms a virtual straight barrier of the eee Long About 3 4m specified fence length l l Set the switch according to the required fence length VIRTUAL GUARD creates an invisible barrier that the robotic vacuum cleaner cannot cross E g in front of pots furniture the front door and so on 1 Select Fence virtual wall mode using the Mode lt l f 1_ Distance Power button 1 Ais The mode lamp flashes red 9 ye J A fence 2 Set the fence length using the distance control virtual wal is switch formed 3 Install the VIRTUAL GUARD in front of the area you want to block access from the robotic vacuum cleaner Install the VIRTUAL GUARD so that the distance detection sensor can form an invisible barrier that the robotic vacuum cleaner cannot cross Operating the cleaner _25 Operating the cleaner The VIRTUAL GUARD forms an invisible door that the robotic vacuum cleaner cannot cross until current room is completly cleaned The VIRTUAL GUARD opens the invisible door when cleaning the of room is complete 1 Select Guard virtual door mode using the Mode Power button The mode lamp flashes green
32. o use the Scheduled Cleaning and Daily Cleaning functions properly setting the time is necessary You can only set the time using the remote control m You can only set the time using the remote control Suppose current time is 07 00 Enter the current hour ju am IDI Enter setup mode Set the hour a m Enter the current minutes am 4 Clock Finish the setting am l E K Press the button instead of the Time Set button while setting the time to exit Time Set mode When a Scheduled Cleaning is set you cannot change the time setting 24 Operating the cleaner Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER INSTALLING THE VIRTUAL GUARD You can confine the robotic vacuum cleaner to Mode Lamp a particular section by using Fence virtual wall Distance Detection mode or clean several sections one by one Sensor A Main Unit Detection Sensor using Guard virtual door mode yet one Distance Control Switch Fence Guard Off 1 Mode lamp operations Fence virtual wall Mode The red lamp flashes Guard virtual door Mode The green lamp flashes Off The lamp is turned off HIANV37O JHL DNILVH3dO 0 2 Setting the mode Whenever you press the Mode Power button Fence virtual wall mode Guard virtual door mode Power off is selected in this sequence 3 Setting the Fence length Distance Detection Se
33. press a button robotic vacuum cleaner judges cleaning to be complete cleaning is not resumed Do not move the robotic vacuum cleaner while it is cleaning or press a button while caution Cleaning Otherwise the robotic vacuum cleaner judges cleaning to be complete and starts cleaning again from the beginning Operating the cleaner _31 Operating the cleaner USING THE ROBOTIC VACUUM CLEANER MANUAL CLEANING You can move the robotic vacuum cleaner to clean ee a particular location directly by using the remote control E Move the robotic vacuum cleaner to the location where you want to perform manual cleaning E You can manually clean using the remote control only Set the mode ka Manual 6 TOEN ka AT Cancel the mode B While cleaning L Rehan Directional Buttons Forwards Left Right A backwards function is not supported B e When the robotic vacuum cleaner is docked NOTE with the charger station manual cleaning is not supported In manual cleaning mode you can navigate to locations such as areas with a fence tape or areas with a risk of falling stairs etc using the remote control CAUTION 32_ Operating the cleaner Operating the cleaner USING THE ROBOTIC VACUUM CLEANER EDGE CLEANING When the Obstacle Sensor detects an obstacle
34. ranty period is 6 months from the date of purchase m When purchasing a battery ask the customer care center for the genuine part symbol gS and model number before purchasing it 3 Battery information AA Size Ni MH UNION SUPPO Model HPY 12 EA This battery is only for Samsung robotic vacuums It is strictly prohibited to use it for other appliances or for other purposes Do not disassemble or modify the battery Charge it in a location with good ventilation Do not expose the battery to fire and do not heat it Do not connect any metallic objects to the or terminals of the battery Keep it indoors 0 C 40 C Before you discard product dispose of batteries in an environmentally safe manner Do not discard this batteries with your regular household trash Follow all local regulations when disposing of old batteries HANV37O JHL DNILVH3dO 0 If the battery is out of order do not disassemble it Contact your nearest customer care center 3 An increased charging time and a shorter battery life indicates the near end of the battery life Please contact an authorized customer care center to replace your battery The rechargeable battery incorporated in this product is not user replaceable For information on its replacement please contact your service provider Operating the cleaner _23 Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER SETTING THE TIME T
35. robotic vacuum cleaner does not vacuum or WARNING Move over liquids such as water oil or pet litter This may result in critical damage to the product Liquids may spread through the wheels resulting in contamination Do not use the charger for other purposes WARNING This may result in critical damage to the charger or cause a fire Safety information _9 NOILVWHOJNI ALSAVS 10 safety information IN USE CAUTION CAUTION CAUTION CAUTION CAUTION You cannot use the robotic vacuum cleaner on thick carpets This may result in problems with the robotic vacuum cleaner This may result in damage to carpets Do not use the robotic vacuum cleaner on a table or other high locations This may result in damage when the unit accidentally drops Robotic vacuum cleaner may bump into furniture such as chair legs table legs thin and long furniture etc while operating For a quicker and cleaner performance place the chairs on top of the table Do not place any objects on top of the robotic vacuum cleaner This may result in malfunction Immediately remove any large pieces of paper or plastic bags from the machine while cleaning Using the machine for an extended period of time with its inlet port obstructed may result in critical damage to the product If an unusual sound smell or smoke is emitted from the robotic WARNING Va
36. s caution Cleaning or press a button while cleaning Otherwise the robotic vacuum cleaner judges cleaning to be complete and starts cleaning again from the beginning When cleaning is complete Operating the cleaner _33 Operating the cleaner USING THE ROBOTIC VACUUM CLEANER SCHEDULED CLEANING You can schedule robotic vacuum cleaner to start cleaning from a particular time m Scheduled cleaning is only performed when robotic vacuum cleaner is docked with the charger station Example Enter Scheduled ae PRA ini sa ebel l f Cleaning mode and MEGESTES ee Timeri Timer Daily confirm that the time 09 30 a m D x l configured time is MAIN correct Lt FINI Start the settings Timer Daily Binks A AM Fl l A Ltt amp Set the hour am FICI i Ltt d Confirm the hour aM TUF ULL Set the minutes ADIN U4JUO Complete the settings am FID ZMI Ls Cancel the settings The icon is turned off When completing the settings and you press the button instead of the Delay note Daily button Scheduled Cleaning mode is exited 34_ Operating the cleaner Operating the cleaner USING THE ROBOTIC VACUUM CLEANER SETTING DAILY CLEANING You can schedule the cleaning robot to start cleaning everyday from a particular time apon Tue Ned m Daily cleaning is only performed when the cleaning robot is docked with the charger station Examp
37. s turned off it will cut off the power supply and deactivate all functions When installing the charger station do not leave the power cord exposed on the floor When the robotic vacuum cleaner automatically recharges or passes by the charger station it may drag the power cord around with it Always keep the power cord of the charger plugged into the outlet Although the robotic vacuum cleaner has a self charging function if the power cord of the charger station is unplugged it cannot charge its battery automatically 8_ Safety information Safety information BEFORE USE Install the charger in a location that can be easily accessed caution by the robotic vacuum cleaner If the charger is installed in a corner this may cause extra movements and may disturb the automatic recharging process Objects in front of the charger will prevent the robotic caution Vacuum cleaner from auto charging itself Clear the area There should be no obstacles 0 5 m to the left and WARNING fight and within 1 m of the front Do not short circuit the charge pins with metal objects such WARNING 45 Chopsticks screwdrivers and etc This will result in critical damage to the charger Make sure that there is no trace of liquids on the charger station Failing to do so may result in fire or electric shock WARNING Make sure the
38. substance dust e Turn off the Power Switch at the bottom and L L stain etc is on the Obstacle wipe the foreign substance from the front sensor window and rear sensor windows using a soft cloth ron e A foreign substance Dust e Turn off the Power Switch at the bottom L U i stain etc is on the Cliff sensor and wipe the foreign substance on the cilff window sensor window with a soft cloth ue je Dust bin not inserted e Insert the dust bin until you hear a Click LU sound e A foreign substance String e Turn off the Power Switch at the bottom and rome cloth etc is caught on the wipe the foreign substance from the edge ttt edge cleaning side rotating cleaning side rotating brush brush 3 If you press the Start Stop button or turn off the Power Switch the error code is cleared Troubleshooting _45 Product soeciication 93 mm Height 355 mm Length l w Main Body 122 mm Height 161 mm Length 275 mm Width Charger Station 46_ Product specification Product soecification CLASSIFICATION ITEM DETAIL Diameter 355mm Mechanical l Specifications Height 93mm Weight 4 0kg Power voltage AC220 240V 50 GOHz l Charge power consumption 50 W Electrical specitricatlona Main unit power consumption 40 W Battery specifications 14 4V 2 000 mA Cleaning Specifications Dust bin capacity About 0 6 Auto Charging Manual Charging type j onan
39. t working as it should has been dropped damaged left outdoors or dropped in water return it to a customer care center Do not handle the charger or robotic vacuum cleaner with wet hands Use only on dry indoor surfaces This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance BATTERY CHARGER Do not modify the polarized plug to fit a non polarized outlet or extension cord Do not use outdoors or on wet surfaces Unplug the charger from the outlet when not in use and before servicing Use only the charger supplied by the manufacturer to recharge Do not use with a damaged cord or plug Do not pull or carry by the cord use the cord as a handle close the door on the cord or pull the cord around sharp edges or corners Keep the cord away from heated surfaces Do not use extension cords or outlets with inadequate current carrying capacity Do not unplug by pulling on the cord To unplug grasp the plug not the cord Do not mutilate or incinerate batteries as they will explode at high temperatures Do not attempt to open the charger Repairs should only be carried out by a qualified customer care centre Do not expose the
40. teries alkaline batteries VIRTUAL GUARD 2 type D LR20 alkaline is too short batteries In the display e Is the robotic vacuum cleaner e When the robotic vacuum panel From forced to seperate from charger cleaner is seperated or pressed 30 29 28 or pressed during charging during the charging after 30 the number is counted down second it returns to the charger for automatic recharging 44_ Troubleshooting jroublesnooting TROUBLESHOOTING FOR ERROR CODES SNILOOHSATENOUL SO CAUSE SOLUTION e Robotic vacuum cleaner is e Turn off the Power Switch at the bottom O FMI l f e U caught stuck or trapped while and move the robotic vacuum cleaner to a navigating different location ror e A foreign substance string e Turn off the Power Switch at the bottom L lil l paper toy etc is caught inthe and remove the foreign substance from the power brush power brush ror e A foreign substance string e Turn off the Power Switch at the bottom and a fe paper toy etc is caught in the remove the foreign substance from the left left driving wheel driving wheel ronc e A foreign substance string e Turn off the Power Switch at the L wos paper toy etc is caught in the bottom and remove the foreign substance right driving wheel from the right driving wheel IB mg e Check bumper sensor e Slightly pull the stuck bumper outward r Ae e A foreign
41. to minimize the bumping impact and the Bumper Sensor also helps it lower the bumping impact And it cleans the corners by reaching to them as close as possible 6 Scheduled Cleaning Mode At the specified time the cleaning robot cleans the floor 7 Daily Cleaning Mode The cleaning robot cleans the floor everyday at the specified time EASY DUST OUTLET Dy The dust output at the top enables emptying the dust bin easily using anormal vacuum cleaner without dust flying around Product Features _13 Product Features AUTO CHARGING When the battery is low the robotic vacuum cleaner is automatically guided to the charger to enable it to perform a quick auto charge ROTATING BRUSH DOO The edge cleaning side rotating brush cleans dust from the edges About 1cm Stair type Vertical type Mb LM ANTI CRASH The robotic vacuum cleaner s innovative driving system makes it possible for it to cross over doorsills with a height of about 1 cm and clean all rooms The robotic vacuum cleaner has been designed so that it does not cross over doorsills that are higher than 1 cm for safety purposes ANTI The robotic vacuum cleaner detects and avoids obstacles in 2 stages First the 7 obstacle sensors detect obstacles in stage 1 and if the robotic vacuum cleaner does crash into an obstacle the 2 bumper sensors absorb the impact
42. ucted by anyone other than a qualified service engineer This may result in damage to the product Remove any foreign substances accumulated on the Obstacle and Cliff sensors on a regular basis Dirt accumulated on the sensors will result in inaccurate functioning of the sensors sensor Safety information _11 NOILVWHOJNI ALSAVS LO Safety information CLEANING AND MAINTENANCE When removing foreign substances always use the cleaning WARNING brush after turning the Power Switch off Failing to do so may result in sudden operation of the unit and cause an injury or critical damage to the product If the power cord is damaged have it replaced by a qualified WARNING Service engineer from the customer care center Failing to do so may result in fire or electric shock Before cleaning the charger make sure to disconnect the WARNING power cord for safety Contact the Samsung Electronics customer care center to WARNING replace the battery Failing to use original batteries will result in product failure x Battery information AA Size Ni MH UNION SUPPO Model HPY 12 EA 12_ Safety information Product Features CONVENIENT VIRTUAL GUARD FUNCTION You can confine the robotic vacuum cleaner to a particular section by using the Fence virtual wall mode or by cleaning several sections one by one using the Guard virtual door mod
Download Pdf Manuals
Related Search