Multibrackets 7350022732629 projection screen
Contents
1. Multibrackets Motorized Projection Screen Operation Manual 1 Thank you for your purchase Multibrackets Europe AB would like to thank you for purchasing a Multibrackets product We hope that this product meets your demands in terms of use and quality Feedback on our product line is highly appreciated Please send us such to the address on the back of this operations manual 2 Power cord connection Before connecting the projector screen to an electric power supply please properly connect the GX16 Controller as follows a Plug the four pin female connector at one end of the connect cable into the four pin male con nector at the right hand side of the screen case then plug the four pin female connector at the other side of the connect cable into the four pin male connector of the GX16 Controller Turn the screw clock wise to tighten the connection b Plug the three pin female connector of the power cord into the three pin male connector of the GX16 turn the screw clockwise to tighten the connection c Plug the power cord into the an electric outlet make sure that the electric voltage is correct An indication will show when the power is switched on 3 How to operate the screen a Stretching out projector screen Press the DOWN key of the switch and the screen will automatically stretch down and then stop when it is fully stretched out b Rolling back projector screen Press the UP key of the switch and th2. e screen will automatically roll up into the metal drum and stop automati cally when the screen is fully rolled up c Stopping projector screen Press the STOP key of the switch to stop the screen at the current position d Adjusting the viewing area of the screen use a screw driver to adjust the viewing area of the screen according to the instructions on the case cover at the right hand side of the screen case Notice a The switch should be positioned at STOP when the screen is not in use b Before rolling back the screen please make sure that there is no insect dust or other object on the screen c The screen can be rolled up and down repeatedly but continuous time of rolling up and down should not exceed 5 minutes to prevent overheat of the motor In case continuous use is necessary you should wait until the motor cools down 4 Remote Control 1 Characteristic of the Remote control a Utilize IR technology to control the screen b Each set of transmitter and receiver of the screen is guaranteed to be compatible c The screen can be operated with either line switch or remote controls Remote control d Type I Radio Frequency Remote Infra red remote receiver control Type Il Radio Frequency Remote Receiver control Type Ill Infrared Remote Receiver control 2 Specification a Voltage AC 190V 240V or AC 95V 125V b Currency lt 6A c Output power lt 800W d Working environment te
3. following a Check that the lamp is reacting to clicks on the remote keys If not check that the battery within the remote is not expired b Check that the power supply to control that the electricity cord is plugged in and that the fuse is not blown 5 Suggested installation method Note When installing or adjusting the screen make sure that the ends of the screen are leveled MU L T tI BRA C K E TS Multibrackets Europe AB Box 7320 SE 103 90 Stockholm SWEDEN Tel 46 0 8 615 04 00 Fax 46 0 8 612 31 73 E mail postmaster multibrackets com www multibrackets com
4. mperature 30 C 70 C e Transmitting power lt 30mV f RF remote control distance 200m g IR remote control distance 7m h Overall dimension Remote L 120mm W 45mm H 18mm Receiver L 120mm W 72mm H 36 mm 3 Function of the Remote control A HCT RF RF Control operation a The remote control is labeled with RF b Push the top button to roll up the screen c Push the middle button to stop the screen d Push the lower button to roll down the screen B HTC IR IR Remote operation a The remote control is labeled with IR b Push the top button to roll up the screen c Push the middle button to stop the screen d Push the lower button to roll down the screen Note The remote control runs on a CK23A 12V battery The remote control is delivered with a battery installed as well as one extra battery included in the package Under normal use of the remote control the battery life time is more than one year C Remote control receiver a Manual switch buttons can be found on the side of the receiver b Push the top button to roll up the screen c Push the middle button to stop the screen d Push the lower button to roll down the screen e Manual switch signal will override the remote control signal when used at the same time f Fuse 110V or 220V 3A Replace the fuse as indicated in the picture 4 Troubleshooting and adjustments If the remote control is malfunctioning please check the
Download Pdf Manuals
Related Search