Strong SRT 55
Contents
1. Problem Possible cause What to do IR sensor light not lit Mains lead unplugged multipoint Check mains lead switch connector switched off multipoint connector on Mains fuse blown Check fuse Bad connection of IR sensor plug Check connection No signal found Aerial is disconnected Check aerial lead Aerial is damaged misaligned Check aerial Out of digital signal area Check with dealer Active antenna requires to switch ON Switch receiver s Antenna Power antenna power external feed ON connect external feed No picture or sound on Scart AV is not selected on your TV Switch to correct TV input TV VCR TV or VCR are not connected to main Check mains lead www strong tv 15 STRONG PART 1 English DIGITAL TV Problem Possible cause What to do Scrambled channel message Channel is scrambled Select alternative channel No response to remote control Receiver off Handset not aimed correctly IR sensor obstructed Hand set batteries exhausted Plug in and turn on plug Aim handset at IR sensor Check for obstructions Replace handset batteries Forgotten channel lock code Re install channels to cancel channel lock Forgotten menu lock code Contact local Service Hotline or send email to our Support via www strong tv After moving the receiver to another room you are no longer able to receive digital reception The aerial feed former new point may come throug2. Available Timeshift settings 10 20 30 40 50 60 min the maximum time is 1h min 2 GB Card Available Record Type TS PS TS Transport stream which include Teletext Subtitles etc PS Program stream which can be played back by PC or another device WARNING Please consider that Timeshift needs min 20 MB free space on the SD card and an accurate Timeshift function is depending on the speed of the used SD card 5 5 5 Safely Remove Storage Device In Media menu select Safely Remove Storage Device and press OK button to safely remove the USB device Then a message is displayed 5 5 6 Disk Format 1 In Media menu select Disk Format and press OK to enter this menu You will see actual used Device and Partition displayed Furthermore the available Capability in GB is shown 2 Press Y buttons to select File System and use lt P buttons to change between FAT NTFS settings 6 0 OPERATION 6 1 Changing Channels There are 4 ways of channel selection stepping through the channel list selection by number from the on screen channel list and using the electronic programme guide EPG 1 Stepping through the channel list To move through the channel list press the Y buttons on the remote control 14 www strong tv PART 1 English STRONG DIGITAL TV 2 Selected by number Enter the channel number directly by pressing numeric buttons and press the OK button to select desired channel 3 Selected by on sc
3. 1 In Channel submenu select TV Channel List with the Y buttons and press OK to enter 2 Use the lt P buttons to change channel group assumed you have already set up Favourite groups 3 With the Y buttons select the channel you want to watch With OK you can watch the selected channel in full screen mode 5 1 1 1 Edit Use this menu to favour lock skip delete and rename channel list Press numeric button 1 to enter edit menu With the Y buttons highlight a channel and press OK to select or press numeric button 0 to select all channels Selected channels will get marked This way of selection can be executed for each of the edit functions m Favor To add selected channel or all channels to a favourite group press the 1 button Use the Y to select a desired group and press OK With lt gt select Yes in the confirmation window and press OK to save Selected channels will get marked with folder symbol m Lock To Lock channel or all channels press button 2 with lt P select Yes in the confirmation window and press OK to save Selected channel s will get marked with the symbol m Skip To Skip channel or all channels press button 3 with lt P select Yes in the confirmation window and press OK to save Selected channel s will get marked with the and will be skipped during channel zapping in full screen mode m Delete To Delete channel or all channels press button 4 with lt P select Yes in the confirmation wi
4. Connecting to a Hi Fi device Fig 5 3 0 YOUR RECEIVER Fig 6 1 SCART PORT To connect to your TV set 2 SD Cardreader Toinsertyour SD card 3 ANTIN To connect an antenna for reception of broadcasting signal support antenna power 5 V DC 4 IR Sensor slot To connect IR eye plug 5 DC IN To connect the power adapter plug 5 V DC 1 A www strong tv 5 STRONG PART 1 English DIGITAL TV 3 1 Remote Control 1 Turns the receiver On Standby 2 0 9 Channel selection or value input 3 Mutes audio output of the receiver 4 RECALL Back to previous shown channel 5 PAGE PAGE Page up down 6 VOL VOL Menu Off Volume up down Menu On navigation amp change settings 7 CH CH Menu Off Channel up down Menu On navigation 8 OK Menu Off Displays the current channel list Menu On Activates the highlighted menu item 9 MENU Menu Off Opens the main menu Menu On You will get one step back Multimedia Go to upper folder 10 EXIT Exits from the menu or sub menu 11 INFO Shows the actual channel information 12 SUB Shows list of subtitle languages 13 EPG Shows the EPG Electronic Program Guide in TV mode 14 Records the TV program to the SD card 15 TIMESHIFT Activates the timeshift function 16 44 gt gt Fast rewind Fast forward 17 TTX Shows Teletext on OSD On Screen Display 18 TV RADIO Toggles between TV and RADIO mode 19 AUDIO Shows list of the current audio channel language 20 GOTO Only used to g
5. Locks the installation menu You can set menu lock to ON OFF Channel Lock Off Manual Age 4 Age 18 New Password To change the password Confirm Password To confirm the new password 5 4 Tools Press MENU button to enter main menu Select Tools and press OK button to enter tools menu 1 Press Y buttons to highlight the desired menu and press OK button to enter 2 Press EXIT button to exit 5 4 1 Receiver Information This menu displays some Receiver information like Hardware Software Build Date and our Web site www strong tv 1 In Tools menu select Receiver Information and press OK button to open receiver information window 2 Press EXIT button to exit 5 4 2 Games This menu allows you to play games Tetris Snake and Othello on this receiver 1 Select Games in Tools menu and press OK button to enter game menu 2 Press Y buttons to select a desired game and press OK button to enter the game Highlight Start and press OK button to start the game For changing levels highlight Setup and use lt P buttons 3 Press EXIT button to quit the game Note You can also press OK button to pause playing 5 4 3 Load Factory Default This menu allows you to reset the receiver back to factory settings clear all existed channels Note This option will delete all your settings and channel lists and set your receiver to factory default 1 Enter Tools menu select Load Factory D
6. 5 3 Removable Disk Information In this menu you can display information about the storage card 1 In Media menu select Removable Disk Information and press OK button to enter this menu 2 Press EXIT button to exit 5 5 4 Record Settings This menu allows you to set the time for Timeshift define Record Type set Standby Mode and Record Recovery 1 In Media menu select Record Settings and press OK to enter this menu 2 Press Y buttons to select a desired item and use lt P buttons to change settings 3 Press EXIT button to exit Timeshift Time min 10 20 30 40 50 60 Record Type TS PS Standby Mode ON OFF Record Recovery ON OFF 5 5 4 1 Time shift and Recording functions Please connect your SD Card in the correct direction to the foreseen port of your receiver Wait a few seconds after the sign for connected device is shown on screen then you are ready to start Time Shift or Record for the broadcasted programme Time Shift Timeshift function allows you to watch a programme in time shifted mode Press the TIMESHIFT button in viewing mode Then you can use the lt P buttons to move the cursor to the desired time which you want to watch afterwards press OK to confirm In case the info banner is not shown you just need to press the INFO button to call it up show again Time Shift and Record To perform this action you have to press the button after you started the Time Shift Then a confirmation window appears where you ne
7. English STRONG DIGITAL TV Power on with last viewed channel User friendly remote control NTSC PAL converting automatically and manually 3 Games Tetris Snake Othello Support of active antenna by 5 V output Depending on local signal conditions gt Availability depending on broadcaster STRONG cannot guarantee the playback of external video files which have not been recorded by this device Accessories m User Manual 1 Remote control unit with 1 Battery coin cell 3 V 1 Infrared eye 1 Power adapter Note The batteries should not be recharged disassembled electrically short circuited or be mixed or used with other types of batteries If rechargeable accumulators instead of batteries are going to be used we recommend using e g NIMH types with low self discharge to ensure long time operation of remote control 2 0 CONNECTION Connecting to TV Terrestrial Antenna IR Eye and Main Power Fig 1 To receive the broadcast signal the terrestrial antenna cable should be connected to the ANT IN connector at the receiver Then connect the IR connector into the receiver and make sure it is properly connected to the IR sensor input Afterwards you can plug the power adapter to the main power source After all connections are established carefully the IR eye LED must light otherwise the Remote Control will not react Connecting to TV and VCR Fig 2 Connecting to DVD Recorder Fig 3 Connecting to a Projector Fig 4
8. buttons to select your desired month date and day Time Press OK to input the time with the numeric buttons Duration Press OK to input desired duration with the numeric buttons Auto Record Use the lt P buttons to adjust On or Off depending if you want Timer to activate recording via SD Card Record Duration Only activated for recording Press OK to input desired duration with the numeric buttons When you want to quit programme timer a saving window appears with lt P select Yes in the confirmation window and press OK to save or select No to cancel Sleep Timer You can set the receiver to switch to Standby in 70 min 30 min 60 min 90 min and 120 min automatically Additionally there is shown the value of time Remains HH MM 5 3 5 OSD Setting This menu allows you to change settings for Subtitle Display OSD Transparency and Load Default OSD Setting Subtitle Display To set the subtitle to DVB Teletext or OFF OSD Transparency To set the OSD transparency from Off 50 OSD Timeout To set the wanted duration for banner display from 3 s 10 s Load Default OSD Setting To clear all OSD settings and reset to default value 10 www strong tv PART 1 e English STRONG DIGITAL TV 5 3 6 Parental Lock This menu allows you to protect the installation menu or channels with a password and you can change the Password If you want to enter the menu you will be asked to input the password default 0000 Menu Lock
9. satisfy international safety standards Please read the following recommended safety precautions carefully The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance Read All Instructions Before you use the product read all operation instructions For more information on accessories such as the lithium ion battery refer to the manuals provided with those products Save These Instructions Save all safety and operating instructions for future reference Heat Warnings Read carefully and follow all warning labels on the product and those described in the instructions Follow Instructions Follow all instructions provided with this product Cleaning Always unplug this product from the wall outlet before cleaning Use only a damp cloth for cleaning Never use any type of liquid or aerosol cleaner or any type of organic solvent to clean this product Attachments For your safety and to avoid damaging the product use only accessories recommended by STRONG Water and Moisture Never use this product around water near a bathtub kitchen
10. Digital Terrestrial Receiver STRONG SRT 55 Picture similar User manual Bedienungsanleitung Manuel d Utilisateur Manuale Utente Manual del usuario N vod k obsluze www strong tv Antenna IRIN 5VDCIN Antenna IRIN 5VDCIN Antenna DVD Recorder Power adaptor EN BE SCART Female to RCA cable Fig 4 Kg Antenna IRIN 5VDCIN Power adaptor AV 2 IN AV 1 OUT STANDBY moog Antenna Ba I Tarep BI CU 12 Power 16 adaptor 20 19 PART 1 e English STRONG DIGITAL TV TABLE OF CONTENTS 1 0 INSTRUCTION 2 1 1 Safety Instructions 2 1 2 Storage 3 1 3 Equipment Set up 3 1 4 Features amp Accessories 4 2 0 CONNECTION 5 3 0 YOUR RECEIVER 5 3 1 Remote Control 6 4 0 FIRST TIME INSTALLATION 6 5 0 MAIN MENU 6 5 1 Channel 7 5 2 Installation 8 5 3 Setup 9 5 4 Tools 11 5 5 Mediat 12 6 0 OPERATION 14 6 1 Changing Channels 14 6 2 Accessing the Electronic Program Guide EPG 15 6 3 Accessing the favourite channels 15 A 1 TROUBLESHOOTING 15 A 2 SPECIFICATIONS 16 Lu ES 0180 500 75 43 0 14 Min from German wired line ES 0820 400 150 H 0 12 Min from Austrian wired line O E 0826 029 928 I a 14 Min from French wired line per June 2008 www strong tv STRONG PART 1 o English DIGITAL TV 1 0 INSTRUCTION 1 1 Safety Instructions This SCART Receiver has been manufactured to
11. G declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004 108 EEC and 73 23EEC RoHS 2002 95EEC Subject to alterations In consequence of continuous research and development technical specifications design and appearance of products may change All product names are trademarks or registered trademarks of their respective owners STRONG 2009 All rights reserved 07 2009 16 www strong tv
12. IT button to exit 5 3 1 OSD Language This menu allows you to set OSD Language 5 3 2 TV System This menu allows to setup different settings concerning your TV set Display Mode PAL NTSC AUTO Aspect Ratio Use this menu to configure the screen aspect between 4 3 PS Pan amp Scan 4 3 LB Letter Box and 16 9 Wide Screen and AUTO Video Output Switch the video output mode either to RGB or to CVBS www strong tv 9 STRONG PART 1 English DIGITAL TV 5 3 3 Region and Time Here you can set your region and time zone Region This menu is used for changing the region setting GMT Usage This menu is used for usage of GMT The options are Off User Define By Region GMT Offset This menu is valid only when selected User Define in GMT Usage menu The GMT offset range is 11 30 12 00 increasing by half hours progressively Date Time Date and Time menus are valid only when selected Off in GMT Usage menu Press OK then numeric button to change the date and time Time Display This menu allow to control whether the time is displayed on screen or not The options are Off On 5 3 4 Timer Setting In this menu you can set a programme timer or sleep timer Programme timer Timer Number You can set 8 timers Timer Mode Off Once Daily Weekly Monthly Timer Service TV Service Radio Service Wake up Channel You can select a desired channel as wake up channel Month Date Day Press Y
13. Information Record Settings Safely remove storage device and Disk Format 1 Press MENU button to enter main menu Select Media and press OK button to enter Media menu 2 Press Y buttons to highlight desired menu and press OK button to enter 3 Press EXIT button to exit Use the three button rows in bottom of RCU for Player operation Description for further usage of buttons will be displayed on screen 5 5 1 Media Player This function allows you to play MPEG 2 Audio and Photo files from connected storage device 1 In Media menu select Media Player and press OK button to enter Media Player menu 2 Press Y buttons to select a desired item and press OK or PLAY button to play the desired files 3 Press EXIT button to exit 5 5 2 Record Manager This menu allows you to playback the recorded files 1 In Media menu select Record Manager and press OK button to enter Record Manager menu 2 Press Y buttons to select a desired recording and press OK or BLUE gt button to playback the desired files 3 Press EXIT button to exit 12 www strong tv PART 1 English STRONG DIGITAL TV During the playback it is possible to perform the following actions Press YELLOW II button to pause the playback Press the pp 44 buttons for fast forward or fast rewind during playback Press GREEN Ok button once to perform slow motion every further press will change the slow motion speed 1 2 1 4 1 8 5
14. ct device the disconnect device shall remain readily operable 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 1 3 Equipment Set up We recommend you consult a professional installer to set up your equipment Otherwise please follow these instructions carefully m Refer to the user manual of your TV and your antenna m Make sure that the SCART cable connector and outdoor components www strong tv 3 STRONG PART 1 English DIGITAL TV ofthe antenna are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver The following symbols will serve as follow WARNING Indicates warning information Ei Tips Indicates any other additional important or helpful information MENU Represents a button on the remote control Bold Character Move to Represents a menu item within a window Italic Character 1 4 Features amp Accessories For all digital Free To Air TV and Radio programmes with outdoor o
15. ed to select Yes for buffering Time Shift and record the present program If you select No then it will only record the program Stop Time Shift If you want to stop Time Shift press EXIT or lt P buttons then a confirmation window appears Select Yes to stop Timeshift or select No to continue Timeshift Record There are 3 different ways to record programmes Instant recording recording from EPG and recording via Timer www strong tv 13 STRONG PART 1 English DIGITAL TV Instant record In viewing mode press the button to instantly start a record on the current channel Press the RED IM button to stop recording If you press the button again you can adjust the duration for this record Insert the time with the Numeric buttons and press OK to confirm then press EXIT to remove the message From EPG Press the EPG button to enter the programme guide than select an event and channel with the buttons described on screen Press button on an event to plan a timer on this event An icon is then displayed besides the planned event If you want to remove the planned record you have to press button again Manual scheduling If you want to set a record manually you can set recording through the Timer menu For details refer to chapter 5 3 4 Timer Setting EI Note In case the available free space on the SD Card is not enough recording operation of broadcast will stop Maximum Available Timeshift setting is 1h min 2 GB Card
16. efault and press OK button you are asked to input password 2 Input the correct password using the numeric buttons the default password is 0000 a confirmation window is displayed 3 Select Yes to return back to factory settings and clear all channels Select No to cancel 4 Press EXIT button to exit www strong tv 11 STRONG PART 1 English DIGITAL TV 5 4 4 Software Upgrade 1 Enter Tools menu select Software Upgrade and press OK button Software Upgrade menu is shown 2 Press Y buttons to select Upgrade by Storage item and press OK button you are asked to input password 3 Input the correct password the default password is 0000 Software Upgrade submenu is opened Then select the correct software file and press OK to start Message will be displayed to confirm update process select Yes to confirm or No to cancel 4 Press EXIT button to exit WARNING After an update the receiver restarts automatically During this process NEVER disconnect the receiver from the main or switch power OFF This can damage your receiver and warranty will void EI Note This receiver has foreseen an over the air update function which might not be available at your local broadcast conditions For further details visit our website www strong tv or contact your local Serviceline 5 5 Media The Media menu consists of following submenus Media Player Record Manager Removable Disk
17. h a distribution system which may reduce the digital signal now received by the box Try a direct feed from the antenna A 2 SPECIFICATIONS Demodulator Demodulator 16 QAM 64 QAM QPSK Transmission mode 2 K 8 K Video Decoder Profile level MPEG 2 MP ML Video resolution 720 x 576 pixels PAL 720 x 480 NTSC Decoding amp Video Out PAL amp NTSC Aspect ratio 4 3 Letterbox 4 3 Pan amp Scan 16 9 Audio Decoder MPEG MusiCam Layer II Sampling rate 32 44 1 48 KHz Audio mode Stereo Joint Stereo Dual Mono Mono Tuner Front End DVB T UHF amp VHF Tuner Input frequency range 174 230 MHz VHF and 470 862 MHz UHF Loop Wel frequency range 47 862 MHz Input signal level 78 20 dBm Multimedia Video recording and playback MPEG 1 and MPEG 2 encoded mpg Audio playback MP3 and WMA formats Picture view JPEG format STRONG cannot guarantee the playback of external video files which have not been recorded by this device Memory and System Flash memory 1 MByte SDRAM 16 MBytes Connectors ANT IN IEC 169 2 Female TV SCART RGB CVBS SD Card port IR remote port General Data Supply Voltage 5 V DC Power Consumption lt 4 5 W Power consumption in Standby lt 1 W Operating Temperature 0 40 C Storage Temperature 30 80 C Operating Humidity Range 10 85 RH Non condensing Size W x Dx H in mm 69 x 137 5 x 20 5 Weight 102 g STRON
18. isassemble the product could expose you to dangerous high voltage points Damage Requiring Service If you notice any of the conditions described below while using a specified AC adapter unplug it from the wall outlet and refer servicing to qualified service personnel 1 Liquid has been spilled onto the product or some other object has fallen into the product 2 The product has been exposed to water 3 The product does not operate normally despite following operating instructions Adjust only the controls described in the operating instructions as improper adjustment of other controls could damage the product and require extensive repair word by a qualified technician 4 The product has been dropped or damaged in any way 5 The product exhibits distinct change in performance Replacement Parts When replacement parts are required make sure that the authorized service centre uses only parts with the same characteristics as the originals as recommended by the manufacturer Unauthorized substitution of parts could result in fire electrical shock or create other hazards Safety Check Upon completion of servicing or repairs ask the service technician to perform safety checks to determine that the product is in good working order Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on or next to the apparatus Where the mains plug or all pole mains switch is used as the disconne
19. nd By Frequency 4 When By Channel is selected use the cursor buttons to select Scan Band and Channel No When By Frequency is selected use the cursor buttons to select Frequency and Bandwidth Select Network Search to ON or OFF highlight Search and press OK to start scan After Channels are found they will be stored and receiver switches to the first one saved in the list 5 2 3 Antenna Setting Press MENU to enter main menu Use the Y buttons to select Installation press OK to enter the menu With the Y buttons select Antenna setting and press OK to enter Press the lt P buttons to change setting If On is selected the receiver will provide 5 V antenna power for active antennas 5 Press EXIT button to exit i Q 5 2 4 Logical channel numbering If LCN Logical Channel Number is activated and LCN signal is provided by operator then channels will be stored at operator defined order You can activate deactivate the LCN function by setting the LCN Mode to ON OFF 5 3 Setup This menu allows you to set OSD Language TV System Region and Time Timer Setting OSD Setting and Parental Lock 1 Press Y buttons to highlight desired menu and press OK button to enter the setting menus Then press Y buttons to select desired item Settings can be changed by pressing lt P buttons You can get better overview if press OK first Now you can select desired setting by A Y buttons and confirm it with OK 2 Press EX
20. ndow and press OK to save If you have done all modifications concerning channel editing press EXIT to cancel 5 1 1 2 Find Press the 2 button in to enter Find menu Use the Y dk buttons to highlight desired letters or numbers and press OK to insert After each character the channel list will search the channel according your input and list the matched channel Press EXIT to quit Find mode 5 1 1 3 Sort Press the 3 button in to enter Sort menu Use the Y buttons to highlight desired sort way and press OK to confirm Default Sorting by searched Order from lowest to highest frequency www strong tv 7 STRONG PART 1 English DIGITAL TV Name A Z Sorting in Alphabetical Order Name Z A Sorting in Alphabetical Order FTA First in the list will be Free To Air channels Lock First will be listed all unlocked and then the locked channels 5 1 1 4 Move Press the 4 button to activate the Move function The selected channel will be marked ina symbol use the Y buttons to move the selected channel to the desired position With lt P select Yes in the confirmation window and press OK to save 5 1 2 Radio Channel list Basically the operation of Radio Channel List is the same as in TV Channel List only difference is that in Radio Channel List there is no video information so it will always display the radio logo at the right preview screen 5 1 3 Delete Favourites and Groups Use this menu to delete all favo
21. ntained around the Scart Receiver Place the SCART Receiver at least 30 mm from the wall Protecting the Power Cord The power supply cord should be placed so it will not be walked on Never put a heavy object on the power cord or wrap it around the leg of a table or chair Keep the area around the power cord connection points at the power outlet and at the product connection free of all AC adapter or accessory power cords 2 www strong tv PART 1 English STRONG DIGITAL TV GENERAL PRECAUTIONS SAFETY PRECAUTIONS Lightning If a lightning storm occurs while using a specified AC adapter remove it from the wall outlet immediately To avoid damage from unexpected power surges always unplug the AC adapter from the power outlet and disconnect it from the receiver when the receiver is not in use Overloading Never overload wall outlets extension cords power strips or other power connection points with too many plugs Foreign Objects Liquid Spillage To avoid personal injury caused by fire or electrical shock from contact with internal high voltage points never insert a metal object into the product Avoid using the product where there is a danger of spillage Heat Never use or store this product near any heat source such as a radiator heat register stove or any type of equipment or appliance that generates heat including stereo amplifiers Servicing Refer all servicing to qualified personnel Attempting to remove the covers or d
22. o to desired position in Record Playback mode 21 COLOURED BUTTONS For Multimedia and Teletext functions Fig 7 8 The remote control transmits a directional infrared beam Be sure to aim the remote control directly at the infrared sensor of the unit during operation If the sensor has been covered or there is a large object between the remote control and the sensor the sensor will not respond The sensor may not able to receive the remote signal when it is exposed to direct sunlight or a strong artificial light fluorescent or strobe light In this case change the direction of the light or reposition the unit to avoid direct lighting 4 0 FIRST TIME INSTALLATION If you use the receiver for the first time the Easy Install menu appears Use the lt gt buttons to change settings for setup of Region OSD Language and Antenna Power and the Y to select Then use the Y buttons to move focus to Search and press OK to proceed with the automatic channel scan 5 0 MAIN MENU In viewing mode always press MENU to enter the Main Menu It consists of following submenus Channel Installation Setup Tools and Media 6 www strong tv PART 1 English STRONG DIGITAL TV 5 1 Channel 1 Usethe A V buttons to select Channel and press OK to enter 2 Use the Y buttons to highlight the desired item and press OK to select 3 Press EXIT to exit Ki Note You can also press OK in TV mode to enter channel list 5 1 1 TV Channel list
23. r indoor antenna Terrestrial Receiver for direct connection to SCART connector TV VCR DVD Projector HIFI 180 rotatable Remote control operates receiver via Infrared Sensor Eye SD Card reader for watching photo albums recording and playing video or music files Pause live TV with time shifted playback via SD card rewind fast forward slow motion and GOTO function Event recording Daily Weekly Monthly One Touch Recording 1 hour recoding file size approx 2 GB Slide show while MP3 is playing Quick and easy installation and user friendly menu Excellent Audio and Video quality 1 000 channels memory capacity Fast channel zapping sorting by alphabet free encrypted channels Electronic TV Programme Guide EPG for on screen programme information of present following event information up to 7 days 8 wake up Timers with 4 modes once daily weekly monthly Sleep Timer 10 30 60 90 120 min Booking of events directly from EPG Full multi lingual DVB subtitling and audio track support Support Teletext via receiver and TV set 8 Favourite lists for TV and Radio programmes Parental lock function for menu and rating control for channels Multi lingual support on screen menu OSD such as English German French Italian Spanish Czech Automatic and manual channel scan options Many channel handling options locking editing moving sorting skipping deleting and searching www strong tv PART 1 e
24. reen channels list You can also select the required channel directly from on screen channel list This is displayed using the receiver s main menu See chapter 5 1 1 TV Channel list in this manual for operation detail Alternatively you can call up channel list by pressing OK in viewing mode 4 Selected by EPG You can also select the required channel directly from electronic programme guide EPG This is displayed by pressing EPG button on remote control See in the below chapter for operation detail 6 2 hehe the Electronic Program Guide EPG Press EPG button to enter EPG menu i Press numeric button 2 to switch between channel list events schedule of the selected channel and now next events 3 In the event schedule press OK button to book the selected event press numeric button 3 to open the Detail menu for the selected event 4 Press numeric button 1 to open the Booking list menu 6 3 Accessing the favourite channels 1 Press OK button to enter channel list 2 Press lt or P gt cursor buttons to select the desired favourite group 3 Press Y buttons to select the favourite channel A 1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver Check the receiver according to the procedures shown below If the receiver does not work properly after checking it please contact the dealer Do NOT open the receiver cover It may cause a dangerous situation and the warranty will get void
25. sink laundry tub wet basement swimming pool or in the rain Location To avoid damage to the product and prevent personal injury never place this product on an unstable stand tripod bracket Follow the instructions that describe how to safely mount the product and use only the mounting devices recommended by the manufacturer Power Sources Connect this product only to the power source described on the product label If you are not sure about the type of power supply in your home consult your local power company Refer to instruction pages for information on using the product with a battery Grounding Polarization If this product is used with a specified AC adapter the adapter may be equipped with a polarized alternating current line plug a plug with one blade wider than the other This safety feature allows the plug to fit into the power outlet only one way If you cannot insert the plug into the wall outlet pull it out reverse it and have the receptacle replaced Ventilation Slots and openings In this case are provided for ventilation to ensure reliable operation of the SCART adaptor and to protect it from overheating These openings must not be blocked or covered The openings should never be blocked by placing the SCART adaptor on a bed sofa rug or heat register This Scart adaptor should not be placed in a built in installation such as a book case or rack unless proper ventilation is provided Ensure that free airflow is mai
26. urite channels Select Delete All Favourites with the Y and press OK with lt P select Yes in the confirmation window and press OK to delete or select No to cancel 5 1 4 Delete all Use this menu to delete all channels Select Delete All with the Y and press OK then enter the Password default 0000 In the confirmation window select Yes with lt gt and press OK to delete or select No to cancel 5 1 5 Group Rename In this menu you can change favourite group name Use the Y buttons to select Group Rename and press OK to enter 1 With the Y buttons select a group and press OK 2 At the appearing Keyboard use the Y dk buttons to highlight desired letters or numbers and press OK to insert After you entered desired group name highlight OK at the keyboard to confirm 3 Press EXIT button to cancel the group rename 5 2 Installation 5 2 1 Auto Scan 1 Use the Y buttons to select Installation press OK button to enter menu 2 With the Y buttons select Auto Scan press OK to enter the menu 3 Press the lt P buttons to change Scan mode and use the Y to highlight Search press OK to start auto scan 5 2 2 Channel Scan 1 Use the Y buttons to select Installation press OK to enter the menu 8 www strong tv PART 1 e English STRONG DIGITAL TV 2 With the Y buttons to select Channel Scan and press OK to enter the menu 3 Use the lt P buttons to select one of two Scan Modes By Channel a
Download Pdf Manuals
Related Search