ACTi ACM-5711 surveillance camera
Contents
1. IP Box Camera ACM 5711 Ver 080131 Ouick Installation Guide gt ACTi www acti com Getting Started 1 1 PACKAGE CONTENTS ACM 5711 Power Adaptor Option Product CD Terminal Blocks for Power amp DI O Warranty Card Accessory 0 1 1 2 PHYSICAL DESCRIPTION 2 Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector Supporting NWA Y this IP device can auto detect the speed of local network segment 10Base T 100Base TX Ethernet Reset Button Step 1 Switch off IP device by disconnecting the power cable Step 2 Press and continue to hold the Reset Button Reconnect the power cable while continuing to hold the reset button Step 3 Keep holding the reset button depressed around 6 seconds release the reset button The unit will start up with factory default settings Audio Input Output The IP device supports audio input and output with earphone jack Action LED Indicator The LED will light up after IP camera has successfully completed the boot process The I O Terminal Connector Used in applications for e g motion detection event triggering 0 2 time lapse recording alarm notifications etc the I O terminal connector provides the interface to el transistor output For connecting external devices such as relays and LED s Connected devices can be activated by Output buttons on the Live View page or by an Event Type The output will show as2. active in Event Configuration gt Port Status if the alarm device 1s activated e digital input An alarm input for connecting devices that can toggle between an open and closed circuit for example PIRs door window contacts glass break detectors etc When a signal 1s received the state changes and the input becomes active shown under Event Configuration gt Port Status e Auxiliary power and GND GND Auxiliary DC Power input not to power this camera Digital Input Transistor Output Pin 1 Ground Description Pin 2 Electrically connected in parallel with the con Voltage 12V DC nector for the power supply this pin provides an Max 1 2W auxiliary connector for mains power to the unit This pin can also be used to power auxiliary equipment with a maximum current of 100mA Pin 3 Connect to GND to activate or leave floating or Must not be exposed to unconnected to deactivate voltages greater than 30V DC Pin 4 Uses an open collector NPN transistor with the Max load lt 100mA emitter connected to the GND pin If used with an Max voltage 24V DC external relay a diode must be connected in to the transistor parallel with the load for protection against voltage transients The I O terminal pins are numbered left to right as shown below Connect input output devices to the camera as follows 1 Attach the cables for the device securely to the supplied green conn
3. 68 0 100 Please make sure this IP device and your PC are on the same network segment before running the installation Internet Protocol TCP IP Properties General You cen get IP settings asrigned automatically your network supports the capabilty Othenwise pou need to ack your network administrator Fot the appropriate F settings Obtain an IP address automatically fS Une the following IP address IP address Subnet mask Detail gateway Chan DKS z i H Use the following DMS server addresses Prefered DNS server Akemate DNS server Please set the settings as below IP address 192 168 0 xxx Subnet mask 255 255 255 0 NOTE xxx should be a number from 1 to 254 but 100 is excepted A Web Configurator Yideo Manager Yersion ACTi DI v2 0 Microsoft Internet Explorer Sele BRO SHE RAD RDRKU IRO BHO Lo GOH x HAG Pra Was B H LJ 3 BE s sest E eb Configurator Camera 1 Account Password Language English v NOTE If your web browser is earlier than IE6 then download IE6 is recommended NOTE This IP device default IP address is set to 192 168 0 100 Login with default administrator s account amp password Accou nt Admin Password Language English a R Copyright 2003 2004 ACTI Corporation All Rights Reserved NOTE Default administrator account is set to Adm
4. ector 0 3 block 2 Once the cables are connected push the connector block into the terminal connector also green on the camera FUSE 1A DC TO DC CONVERTER ir reg LP O 6 Power Input If your power input is DC12V 7 Analog Video Output The IP Box Camera supports one channel analog video output 0 4 8 9 10 Iris DC Iris Video DC Level Adjustment CCD Functions Auto Electronic Shutter Speed Mode AES On 1 50 60 sec 1 120 000 sec AES Off 1 50 60 sec Automatic Gain Control ON OFF Switchable Auto White Balance AWB Push Lock WB Mode Back Light Compensation ON OFF Switchable Sense UP ON OFF Switchable 0 5 1 3 BASIC CONNECTIONS Follow the procedures below to connect the IP device to the respective apparatuses 1 Connect the power adaptor to IP device 2 Connect IP device s ethernet port to an Ethernet RJ45 connectors If your IP device has PoE built in you can regard it as a PD and connect it directly to a PSE device like PoE switch 3 Connect a PC to the Ethernet hub RJ45 connectors NOTE You may find a support package for help you getting familiar with PoE Please visit our web site and get the support document TS 00040 0 1 Ouick Tour This section guides you with a quick tour on this IP device 2 1 Configure this IP Device 2 1 1 Make sure network environment Default IP of this IP device 1s 192 1
5. in password is set to Login 123456 and click button 1 3 2 1 4 Preview the video gt gt Ouit 2 1 5 W K T Video Display gt Hasi seii gt WAH Seting Date Samiii Video Setting Video Adjust gt User Account System ki o Fit rve Set the new IP address Copyright 2003 2007 ACTi Corporation All Right Reserved Camera 1 oS WAN Setting Dynamic IP Address Static IP Address IP Address 192 168 Subnet Mask 255 255 ISP Gateway 192 166 PPPoE UserName Password AE Apply 0 100 755 lo 0 254 IP Address The default IP address is 192 168 0 100 Subnet Mask The default subnet mask is 255 255 255 0 SENI button Click NOTE In your Client PC please make sure the setting of Network Connections Type is set to Auto Negotation since this IP device follows MII standard Otherwise you might not see the live image IMPORTANT After the IP address is changed please record this IP address There s no way to connect to the IP device if user forgets the new IP address 2 1 6 Check Default Video Setting V4 ACT gt gt Video Display J9 Version V2 0 Video Setting RESTARE I Camera Name Camera 1 gt gt WAN Setting Streaming Method TCP Only v gt gt Date Setting Audio In Disabled v gt gt Video Setting Ana
6. log Video re d Resolution N640x480 w gt gt Video Adjust TS Frame Rate Mode Constant gt gt Camera Setup Frame Rate 30 v gt gt User Account Video Encoder MPEG4 w gt gt System Info Video Bitrate Mode Constant Bit Rate v gt Fine Video Maximum Bitrate UNLIMITED vi Bitrate 3M x gt gt Factory Default Serial Port Baud Rate 9600 x dasa aa Serial Port Control 8 None 1 v gt gt Logout Video Control Port 6001 Video Streaming Port 6002 Apply Copyright 2003 2007 ACTi Corporation All Right Reserved NOTE reguirement and click 2 1 7 for system reboot Please make sure the TV Input NTSC PAL is meet your Apply button Click Save Reboot to restore all settings and please wait about 30 seconds 1 5
Download Pdf Manuals
Related Search