Philips DCR2022 Digital Cable Receiver
Contents
1. Menu Favourite lists and channel locking Conditional access User preferences Setup System information Menu Tree More about recording VCR or DVD control Connection for Easy Recording Digital receiver and VCR or DVD settings Recording with the VCR control feature Troubleshooting Technical specifications 4l DCR 2020 indice3 25 09 07 14 17 Page 42 Introduction Welcome to digital television The Philips Digital Cable Receiver allows you to view a wide variety of channels with the best digital picture and sound quality With this product you can enjoy advanced functions and features including Digital picture and sound quality Wide screen format TV SCART and VCR DVD SCART connector Up to 500 presets for TV and Radio channels Easy installation and use through the well tested Euphoria User Interface Personal channel list and favourite lists Electronic Programme Guide This user manual covers the installation of your receiver and the necessary steps to use the various functions so you can optimally enjoy every feature DCR 2020 indice3 25 09 07 14 17 Page Product description Front panel ii fa nen WS LS C N DER 2020 _ DIGITAL CABLE RECEIVER a v ak en do PHILIPS m 1 Smart Card slot see chapter Inserting your Smart Card 2 Din rear channel I AI channel dle mute demute Be Oil ON Standby The front panel button h2. RADIO to toggle between TV and radio modes DCR 2020 indice3 25 09 07 14 17 Page Volume amp Audio Control Volume control and Mute To decrease or increase the volume use IN The volume level can also be controlled from your TV To mute the sound press X A change of volume is signalled on screen using a bar graph while audio mute is signalled with an icon in the top right corner of the screen Audio mode cE gt To access audio settings m Select Setup from the main menu then select TV configuration Scroll to TV audio signal and set the desired value Stereo Mono or Dolby digital Press OK to save your changes and exit the screen PHILIPS Audio language To select your preferred audio language Select User preferences from the main menu then select Languages Scroll to Audio Language and set the desired language Press OK to save your changes and exit the screen If you want to change the audio mode or language for a particular programme press I Il to directly access the audio options available for this programme Available languages depend on the audio content transmitted Recording timers Recording timers are used for VCR or DVD recordings Setting a timer from the Guide Select Guide from the main menu or press GUIDE Move to the desired programme using the arrow keys Press TIMER to set a recording timer on the selected programme Enter your PIN code
3. if necessary and then set the timer as appropriate By default the settings correspond to the selected programme Press OK to confirm 53 DCR 2020 indice3 25 09 07 14 17 Page Setting a timer while watching digital TV or listening to digital radio Press TIMER Set the desired Timer type Recording timers Reminders or Sleep Timer and then press OK Set the values of the recording parameters using the arrow or number keys as appropriate for more details refer to paragraph Recording timers and Reminders Press OK to confirm Setting a timer from the Timers sub menu Select the Recording timers item from the Timer sub menu Select Add timer Set the values of the recording parameters using the arrow or number keys as appropriate for more details refer to paragraph Recording timers and Reminders Press OK to confirm Deleting an active timer A timer is active Recording is signalled by two front LEDs the right hand one lit in red and the left hand one lit in green in TV mode or in orange in Radio mode or both LEDs lit in red if your receiver is in standby To delete the active timer If your receiver is in standby press P P or any number key of the remote control Press the key sequence TIMER then 0 The red light then switches off and you can change channels When a recording timer is active you cannot change digital channels but you can switch to analogue TV u
4. pe Conditional access Conditional access is used to view information on your receiver and smart card including the receiver and smart card version It is also used to change your receiver PIN code N The PIN code default value is 0000 59 DCR 2020 indice3 25 09 07 14 17 Page sep PHILIPS PHILIPS PHILIPS t PHILIPS 60 Changing PIN code Scroll to Changing PIN code and then press OK Enter your current PIN code and press OK Enter your new PIN code and press OK Enter your new PIN code again and press OK Once you have changed your Pin Code keep it secret to prevent others from using it If you forget or lose your Pin Code call your customer service adviser User preferences User preferences is used to e set the language and on screen display options according to your preferences e enable and set up Parental control Languages Set values for the following e Menu Language Audio Language and Subtitles Language e Subtitles Mode Translation Hearing impaired or Off Press OK On screen display Set values for the following Banner timeout banner display duration from 3 to 10 seconds in steps of 1 second e Volume bar display Yes or No Volume bar timeout volume bar display duration from 3 to 10 seconds in steps of 1 second Press OK Access Control Access control is used to enable and set up parental control options To access this screen you must enter you
5. socket of your TV using the SCART lead supplied with your digital receiver Connect the WCR SCART socket of your digital receiver to the EXT2 SCART socket of your VCR called IN using a SCART lead Connect the EXT1 SCART socket of your VCR called OUT to the EXT2 SCART socket of your TV using a SCART lead Plug all your equipment excluding your digital receiver into the mains Switch on your TV set and select a channel Plug your receiver into the mains The welcome screen appears then the First installation screen the right hand LED is lit in green Read the Quick installation guide to proceed with the channel scan if not already done With this connection set up e You can watch digital TV while you record analogue TV e You can watch analogue TV while you record digital TV e You can record the digital TV channel you are watching Some VCR or DVD recorders need to be in standby to use the Easy Recording feature Refer to your VCR or DVD User manual Digital receiver and VCR or DVD settings Refer to chapter More about recording VCR or DVD control for information on how to enable the Easy Recording function on your digital receiver Depending on your VCR or DVD brand and type you have to set the VCR recording control option to Prepare Record or Record Link Refer to the VCR or DVD User manual or try the two options to find out which is most suitable Set your VCR or DVD to
6. 8 Page More about recording VCR or DVD control Connection for Easy Recording This connection allows automatic recording without requiring you to program your VCR or DVD recorder You must however set a timer on your receiver as described in paragraph Timers Prior to choosing this connection method Consult the user manual of your VCR or DVD recorder to check if and how this feature is supported Most Philips VCR and DVD recorders support one of the two Easy Recording options e Check that your TV and YCR or DVD are both fitted with two SCART sockets Incorporate your receiver in your existing installation as shown below TV set Faure Cable Wall socket us Za A sta 1 ENTE 2 5 i A to AC outlet VCRIDVD IN FROM ANT OUT TO ANT EXT2 ID For optimum configuration Screw the adapter supplied with your receiver on the RF IN socket of the rear panel Connect the receiver RF IN socket with adapter to the cable wall socket Connect the RF OUT socket of your digital receiver to the aerial input socket of your VCR or DVD using the antenna cord type F IEC Connect the RF OUT socket of your VCR or DVD to the aerial input socket of your TV using a RF coaxial lead 64 DCR 2020 _ indice3 25 09 07 14 18 Page ep Connect the TV SCART socket of your digital receiver to the EXT1 SCART
7. Anali AUDIO Digital nalogue input input 7 R L to AC outlet a Cable Receiver Analogue connection A Connect the L R audio output sockets to the relevant L R audio input sockets of your audio equipment using a double CINCH cable not supplied Consult the user manual of your audio equipment to choose the proper analogue audio inputs Digital connection B Connect the audio SPDIF output socket to the relevant digital audio input socket of your audio equipment using a single CINCH cable not supplied Consult the user manual of your audio equipment to choose the proper digital audio input With this connection set up you can only control the audio volume up down and mute from your audio equipment 48 DCR 2020 indice3 25 09 07 14 17 Page First installation PHILIPS PHILIPS PHILIPS For fast and successful start up check that your receiver is connected to the wall socket TV set and other equipment according to the diagrams in chapter Connecting your receiver Switch on the receiver and TV set The welcome screen appears then the First installation screen First installation settings Set your favourite menu language and press OK Set appropriate values for the following e Network ID applicable network ID as indicated by your operator See operator booklet for the right decimal value to be entered for your region Frequency broadcast frequency predefine
8. Channel current channel Alternatively press the green colour key to display the list of available channels Then scroll to the channel on which the DCR 2020 indice3 25 09 07 14 17 Page programme you want to record is broadcast using the A or W key and press OK to select it Press OK to confirm When a recording timer is active you cannot change digital channels but you can switch to analogue TV using the TV STB key and zap through analogue channels To delete an active timer press the key sequence TIMER 0 Modify an existing timer before its activation Select Modify timer from list from the Recording timers or Reminders sub menu depending on the type of timer you want to modify Select the timer you want to modify from the list Modify the appropriate settings Press OK to confirm PHILIPS Delete an existing timer Select Delete timer from list from the Recording timers or Reminders sub menu depending on the type of timer you want to delete Scroll to the timer you want to delete from the list Press OK to confirm Sleep timer You can set a sleep timer to automatically switch your receiver to Standby mode after a given time lapse PHILIPS Set a sleep timer Select the time lapse after which the receiver should go to Standby up to 3 hours using the or key Press OK to confirm Disable a sleep timer Select OFF instead of a time lapse Press OK to confirm
9. DCR 2020 DCR 2022 www philips com support NL Handleiding 2 EN User Manual 36 DE Benutzerhandbuch 70 PHILIPS DCR 2020 indice3 25 09 07 14 17 Page ep 36 Meaning of symbols Important information Must be read and understood 1 Your product has been designed and manufactured with high quality materials and components which can be recycled and reused When this crossed out wheeled bin symbol is attached to a product or his packaging it means the product is covered by European Directive 2002 96 EC Please inform yourself about the local separate collection system for electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste The correct disposal of your old product will help prevent potential negative consequences for the environment and human health a The Material recyclability symbol affixed on package cardboard and user manual means these parts are recyclable So do not dispose of them with your normal household waste The Material recyclability symbol affixed on plastic packaging parts means these parts are recyclable So do not dispose of them with your normal household waste The Green Dot affixed on cardboard means PHILIPS pays a financial duty to the Avoidance and Recovery of Packaging Waste organization DCR 2020 indice3 25 09 07 14 17
10. HILIPS a EXT EXT2 mm E E Cable Receiver A to AC outlet 38 DCR 2020 indice3 25 09 07 14 17 Page la i PHILIPS PHILIPS 4 To avoid incorrect insertion of the smart card in the slot make sure you affix the reminder sticker supplied with your receiver on the smart card so as to cover the following text Deze zijde boven on the side that has no chip Insert your smart card in your receiver with the golden or silver contacts facing up Insert the two batteries supplied in your remote control Batteries are removable from the remote using common household tools like a screwdriver The batteries supplied do not contain hazardous substances such as Mercury Cadmium or Lead However they must not be disposed of with your household waste but to a local separate collection system 7 Reconnect your TV set and recorder to the mains Do not connect your receiver yet 8 Switch on your TV set and select a channel 9 Plug the receiver s power cord to the mains The welcome screen appears then the First installation screen 10 Set your favourite menu language and press OK lI Set appropriate values for the following e Network ID applicable network ID as indicated by your operator Please see operator booklet for the right decimal value to be entered for your region Frequency broadcast frequency predefined or entered manually as indicated by your operat
11. Page ep Safety instructions Your receiver has been manufactured to meet the appropriate safety standards but the instructions below must be followed to operate it safely These instructions must be kept for future reference Before connecting the receiver to the mains check that the mains supply voltage corresponds to the voltage printed on the rear of the receiver If the mains voltage is different consult the dealer The receiver does not contain any user serviceable parts All maintenance work must be carried out by qualified personnel If you disconnect the receiver from the mains make sure to unplug it from the wall socket and not just from the AC socket at the back of the unit Children could seriously injure themselves as the free end of the cable is still alive Unplug the receiver during lightning storms To prevent fire or shock hazard do not expose this equipment to rain or moisture The receiver should be placed on a firm surface and the ventilation openings must not be covered with items such as newspapers table clothes curtains etc Do not install the receiver near any heat sources such as radiators stoves or other apparatus that produce heat Protect it from direct sunlight When installing the receiver ensure there is a gap of approximately 2 5 cm around the receiver to enable air to circulate freely and prevent overheating Leave accessible the mains connector at the back of the uni
12. a particular channel message asks for your PIN code Enter your PIN code to access the channel or unlock it The default Pin code is 0000 You set a timer but did not The recorder was set record what you wanted incorrectly Make sure that your recorder is set for the same time as your receiver The order of the channels They have been re arranged has changed Refer to paragraph Favourites lists to change the order again You have forgotten your default PIN code The default PIN code is 0000 If you have tried all of the actions suggested above and could not solve the problem contact your customer service adviser 67 DCR 2020 indice3 25 09 07 14 18 Page ec 68 Technical specifications This product is in conformity with European Directives 95 47 EC and 2002 21 EC System Specifications Audio Decoding CPU Video graphics 8 MB SDRAM Flash memory size 2 MB Video decoding MPEG 2 DVB up to MP ML Video bit rate up to 15 Mbit s Video format 4 3 and 16 9 resolution up to 720x576 pix CPU speed 60 MHz Ram size 8 MB SDRAM Tuner Reception Transmission Symbol rate 1 6 9Ms s Convenience Child Protection Child Lock Parental Control Ease of Installation Auto install Events timer reminder 10 Radio favorite list 3 TV favorite list 3 Parental control Lock with PIN code Child timer Programmable Events 1 Recording Re
13. audio receiver system RS232 socket used for serial data transfer The label showing the type and serial number is underneath the receiver 1 SCART is also called Euroconnector or Peritel Safety Extra Low Voltage Hazardous Voltage 44 DCR 2020 indice3 25 09 07 14 17 Page Se Remote control 0 9 number keys In TV radio mode select channels In menu directly select a menu item or set a setting In standby wake up the receiver S INFO Switch between normal viewing Channel Banner and Channel Banner with Extended Info VOLUME 1 Increases Decreases the volume level 4 Imi MUTE IK Mute Demute the sound on DM ls your TV or receiver x 4 CSS ea RED GREEN YELLOW BLUE Contextual keys n TVISTB Toggle between watching digital TV via your receiver and standard analogue TV via your TV set I 11 Open the Audio Languages screen to momentarily change the soundtrack and audio mode 4 S J ACE TETTI MENU Opens Closes the Menu REC Open Close the Timer screen x 4 EXIT Return to normal viewing E 4a N Standby O Switch your receiver into the standby mode EPG Opens Closes the Programme Guide BACK In TV radio mode return to the previously tuned channel In menu mode return to the previous screen CURSOR A V Switch the Channel Banner in the browsing mode Sc
14. ayed in the background Press OK again to close the list 51 DCR 2020 indice3 25 09 07 14 52 icon TI mO DO z description alternate audio language format current favourite list maturity rating locked scrambled channel locked channel subtitles presence teletext presence 17 Page Ep Channel banner Every time you tune to a channel the channel banner appears displaying information on this channel including information on the current programme The channel banner is displayed for 5 seconds as per default This can be adjusted from the Appearance item of the User Preferences sub menu While watching a channel you can display the current channel information at anytime by pressing INFO Press INFO again to get more information about the current programme Press INFO a third time to close the channel banner Channel Lists While watching digital TV or listening to digital radio you can access existing channel lists by pressing FAV Successively press FAV to toggle between the favourite lists you created and the list of all available channels The current channel list is indicated on the left hand side of the banner When one of the favourite lists is activated you zap only through the channels this list contains To create and edit your favourite lists see paragraph Favourites lists TV or Radio mode selection While watching digital TV or listening to digital radio press
15. cord failure alarm Record header message Signal strength indication User Interface Automatic program list update Multiple subtitles supported Now amp Next ESG On Screen Display on TV TV and Radio mode 7 day Electronic programme Guide Compression format MPEG layer I II Video Decoding Frequency range MHz 950 2150 Video bit rate up to 15 Mbit s Conditional access system Irdeto card not supplied subscription needed for pay TV De scrambling Smart Card reader Connectivity Audio Output Analog Volume controlled L R cinch L R cinch Audio Output Digital AC3 over SPDIF Optical Coaxial cinch Plug amp Play TV SCART out Controlled audio L R CVBS RGB S Video for LCD projector VCR SCART in Audio L R CVBS RGB Accessories Batteries 2 x AA Included Accessories Remote Control High quality SCART cable Mains cord Antenna Cord type F IEC Adapter F male IEC female Sticker to be put on your smart card Leaflet explaining what to do with the adapter and sticker mentioned above Warranty booklet User Manual Dimensions Carton dimensions W x H x D 320 x 85 x 295 mm Product dimensions WxHxD 238 x 42 x 145 mm Temperature operation 5 to 40 C Temperature storage 20 to 70 C Weight 0 98 kg Weight incl packaging 1 780 kg Power Power consumption 10 W Power supply 230 V 50 H
16. d or entered manually as indicated by your operator see operator booklet Symbol Rate predefined value which should not be modified unless requested by your operator e Modulation predefined modulation type which should not be modified unless requested by your operator Symbol rate and modulation may be modified A manually upon request by your operator Press OK to start scanning for channels Channel scanning During the scanning process the following information is reported on screen e number of TV and Radio channels detected e name of the network detected e level and quality of reception of the signal When scanning has been successfully completed a completion message is displayed and then the receiver tunes to the first channel in the list 49 DCR 2020 indice3 25 09 07 14 17 Page 50 Scanning failure In case of channel scanning failure a failure message is briefly displayed and then the main menu appears in case of first attempt Select Setup then Channels installation and proceed as described in paragraph Channels installation to launch a new scan If installation fails again the Setup sub menu appears select Channels installation and proceed as described in paragraph Channels installation Before starting a new scan It is recommended to do the following checks connections to your receiver see chapter Connecting your receiver e number of channels available in the region correspon
17. ding to your area network settings provided by your operator see operator booklet If the same failure message appears after a while refer to chapter Troubleshooting Contact your cable operator if the problem remains DCR 2020 indice3 25 09 07 14 17 Page Ep General Viewing Functions This section describes the basic functions available while watching digital TV or listening to digital radio For general menu navigation see Settings Receiver wake up Your receiver is in standby Press P P or any number key of the remote control Alternatively press Y or A on the front panel A Your receiver as any electronic equipment consumes power In order to reduce power consumption please switch your receiver to standby whenever you are not using it For maximum energy saving we recommend you switch off the receiver by unplugging it from the mains if you are not using it for a long time Channel selection Using P P or number keys To change channels use P P or the number keys of the remote control Previous Channel Recall Press BACK to move to the previous channel you watched in the current channel list Using the channel list To view the list of all available channels while watching digital TV or listening to digital radio press OK PHILIPS If you press BACK the channel list disappears To select a channel Scroll up or down to the desired channel Press OK The current programme is displ
18. guration Select appropriate values for the following e TV Format 4 3 or 16 9 e TV aspect ratio full format 16 9 Letter Box 4 3 Center e TV output signal CVBS RGB or S Video e TV audio signal Stereo Mono or Dolby Digital e VCR Video Output CVBS or SVideo VCR Recording control NO PREPARE RECORD or RECORD LINK See chapter More about recording VCR or DVD control Video mode PAL or SECAM Press OK to store the settings 61 DCR 2020 _ indice3 25 09 07 14 18 Page O 62 PHILIPS PHILIPS PHILIPS Software Upgrade Software upgrade is used to check for new software availability If new software is available Press OK to accept the upgrade The receiver restarts Factory Settings Factory settings is used to restore the receiver factory configuration Press OK when prompted to confirm If you reset your receiver to factory settings you lose all data and information previously stored and you have to restart first installation System information System information is used to display the receiver reference software and hardware ID as well as Total running time in hours DCR 2020 indice3 25 09 07 14 18 Page e Menu Tree Graz ey a e ee ME gt REcording timers Add timer Modify timer from list Delete timer from list Remindess gt Add timer Modify timer from list Delete timer from list Se En 2 63 DCR 2020 indice3 25 09 07 14 1
19. ides the remote control receiver window and includes two LEDs indicating the receiver status One of the LEDs blinks at remote control command reception Receiver operating mode LED1 LED2 Standby off red Running in TV mode off green Running in Radio mode off orange TV recording in progress red green Radio recording in progress red orange Recording ongoing during standby red red Download in progress blinking red off If the red LED is blinking continuously it indicates that an upgrade of your terminal software is taking place Do not interrupt this operation Wait for the green LED to light up indicating successful upgrade and then continue as normal 43 9 DCR 2020 indice3 25 09 07 14 17 Page Rear panel 1 230V 50Hz 10W max 2 RFOUT B REN ATN une ie I NCR ee i IR elet T SPDIF i 8 SERIAL SE er el Socket used to connect the power cord RF output used to connect your receiver to a VCR TV set to watch analogue channels only or to connect another receiver using the adapter supplied with your receiver RF input used to connect the cable from the wall socket Refer to chapter Connecting your receiver SCART 1 socket used to connect to your TV set SCART 1 socket used to connect your video recorder or DVD player recorder Left Right analogue audio cinch outputs used to connect your HiFi audio receiver system Digital audio cinch output used to connect your HiFi
20. lue colour button to access the Skip all Add all features then use the green colour button to add all available channels to the current list or the red colour button to remove all channels from this list e Use the yellow colour button to access the Sort Move features then use the red colour button to perform an automatic alphabetical sort or the green colour button to manually move individual channels e Use the red colour button to lock or unlock channels belonging to the list If you lock a channel belonging to several lists it is locked in all the lists Locked channels are marked with a lock icon If you have selected the TV or Radio list only the lock unlock feature is available Press MENU or BACK to exit the screen You are then prompted to confirm your changes To delete a favourite list Select Delete a favourite list from the Favourites lists sub menu Select the list you want to delete When prompted press OK to confirm deletion Press OK to return to the Favourites lists sub menu When you activate one of the favourite lists by pressing FAV while watching digital TV or listening to digital radio the receiver only zaps through your favourite channels Press FAV to again toggle between your favourite lists and the full channel list 57 DCR 2020 indice3 25 09 07 14 17 Page p 58 PHILIPS PHILIPS Timers Timers is used to set and edit recording timers for the p
21. nd make changes using the lt or key to select an option or number keys to enter numerical values To open a locked menu item indicated by a L icon you need to enter your PIN Code Cancelling storing changes Either press EXIT to exit the menu system without storing changes Or press OK to validate changes and exit the screen Favourite lists and channel locking At installation all the channels found are added to the TV or RADIO list From these two lists you may create favourite lists according to your preferences Favourite lists is used to create modify and delete lists of favourite channels A Modification features include channel locking DCR 2020 indice3 25 09 07 14 17 Page E PHILIPS PHILIPS PHILIPS To create a favourite list Select Create a favourite list from the Favourites lists sub menu Set the type of channels you want to list e Channels TV channels or Radio channels e Free2Air scrambled All Scrambled or Free2air Press OK to display the list of channels matching the above criteria Modify your favourite list as described below To modify a favourite list Select Modify a favourite list from the Favourites lists sub menu Select the list you want to modify Modify your favourite list e Use the green colour button to individually select the channels you want to add to the current list Selected channels are marked with a tick e Use the b
22. ng your receiver There are several ways you can connect and incorporate your digital receiver into your existing audio video equipment set up A Before starting to connect Unplug all equipment TV set as well as VCR and or DVD or DVD R if required from the mains Do not connect your digital receiver to mains supply now Check your current wiring you may not need to modify your existing audio video set up connections if they already match the connection diagrams below Depending on your exiting set up choose the best suited connection method for incorporating your digital receiver When adding new equipment be sure to refer to the related installation instructions of the manual of the respective devices Connecting to TV and VCR DVD player using SCART Support TV set e Be Cable Wall socket PHILIPS gt ZE E z to AC outlet Cable Receiver 2 VCR DVD IN FROM ANT OUTTO ANT For optimum configuration Screw the adapter supplied with your receiver on the RF IN connector of the rear panel Use the antenna cord type F IEC supplied to connect your receiver to the VCR DVD Use the SCART cable supplied to connect your receiver to the TV set For best DVD VCR viewing connect the DVD VCR SCART EXT 1 directly to the TV set SCART 47 DCR 2020 indice3 25 09 07 14 17 Page Connecting to your audio equipment Audio equipment
23. or please see operator booklet Symbol Rate predefined value which should not be modified unless requested by your operator e Modulation predefined modulation type which should not be modified unless requested by your operator A Symbol rate and modulation may be modified manually upon request by your operator 12 Press OK to start scanning for channels When scanning has been successfully completed a completion message is displayed and then the receiver tunes to the first channel in the list 39 DCR 2020 indice3 25 09 07 14 17 Page E 40 Contents 36 37 38 38 42 43 43 44 45 46 47 47 48 49 49 49 50 5I 5I 5I 52 52 52 53 53 55 Meaning of symbols Safety instructions Quick installation guide Unpacking the receiver Introduction Product description Front panel Rear panel Remote control Inserting your Smart Card Connecting your receiver Connecting to TV and VCR DVD player using SCART Support Connecting to your audio equipment First installation First installation settings Channel scanning Scanning failure General Viewing Functions Receiver wake up Channel selection Channel banner Channel Lists TV or Radio mode selection Volume amp Audio Control Recording timers Guide Electronic Programme Guide 9 DCR 2020 indice3 25 09 07 14 17 Page E 56 56 56 59 60 61 62 63 64 64 65 65 66 68 Settings
24. r PIN code Set appropriate values for the following e Parental control Enabled or Disabled e Receiver lock Setup menu lock and Channel lock select to Yes to enable PIN code protection in order to prevent undesired use e Maturity level set a level from 1 to 18 to prevent access to programmes which maturity rating is higher Press OK DCR 2020 indice3 25 09 07 14 18 Page ee PHILIPS PHILIPS PHILIPS PHILIPS Setup Setup is used to e install channels e test signal level and quality modify the general settings of your receiver e check for software updates restore the receiver factory settings Access to this menu can be protected by Pin Code Channels installation Select appropriate values for the following e Network ID applicable network ID as indicated by your operator See operator booklet for the right decimal value to be entered for your region Frequency broadcast frequency predefined or entered manually as indicated by your operator see operator booklet Symbol Rate predefined or entered manually as indicated by your operator e Modulation modulation type predefined or entered manually as indicated by your operator A Symbol rate and modulation values should not be modified unless requested by your operator Press OK to start scanning for channels Signal Test Signal Test is used to view the signal level and quality for the frequency defined at installation TV Confi
25. rogrammes you want to record using your VCR or DVD recorder reminders to receive a warning and automatically change channel before the start of programmes you want to see e sleep timers A To be able to record a digital channel using aVCR or DVD recorder you must set both your recorder and receiver You must set a timer on your receiver You must also enable recording on the VCR or DVD recorder either by enabling an Easy Recording option or by programming your recorder refer to chapter More about recording VCR or DVD control and to the VCR or DVD recorder user manual Recording timers and Reminders Add a recording timer or a reminder Select Recording timers or Reminders depending on the type of timer you want to set Select Add timer To add a timer you may also press TIMER while watching digital TV or listening to digital radio or press the appropriate colour key from the Guide Set values for the following Date set the date using the number keys If you added the timer from the Guide or using the TIMER key the date is already set to the current day e Repeat set Once for a single recording Monday Sunday to record on such day every week Week end to record on both Saturday and Sunday every week Weekdays to record from Monday to Friday every week or every day to record once every day e Start time set a start time using the number keys Stop Time set a end time using the number keys e
26. roll up down in a menu or channel list CURSOR lt gt In Channel Banner switch between the current and next programme OK Confirm your choice P P In TV radio mode tune the next previous channel within the current channel list In standby wake up the receiver TEXT In TV radio mode enable disable teletext display SUBTITLE Open the Subtitles Language screen to momentarily change subtitles language FAV Open Close the current channel list RADIO In TV radio mode toggle between TV and Radio J S 45 DCR 2020 indice3 25 09 07 14 17 Page Inserting your Smart Card DCR 202 DIGITAL CABLE RECEIVER A Y 4 PHILIPS men do To be able to receive scrambled digital channels specific to an operator you need a smart card from that operator Your operator may update it from time to time To avoid incorrect insertion of the smart card in the slot make sure you affix the reminder sticker supplied with your receiver on the smart card so as to cover the following text Deze zijde boven on the side that has no chip A Insert the smart card with the chip facing up Push the smart card into the slot as far as it will go The end of the card will be visible outside the slot New and updated information may be downloaded onto the smart card from time to time 46 DCR 2020 indice3 25 09 07 14 17 Page TE Connecti
27. sing the TV STB key and zap through analogue channels 54 DCR 2020 indice3 25 09 07 14 17 Page Guide Electronic Programme Guide The TV Radio Electronic Programme Guide EPG provides an overview of available TV and Radio channels and programmes the broadcasters have scheduled starting with the current programme To view EPG data Press GUIDE when watching a channel or select Guide from the main menu Highlight the name of the programme for which you want more detailed information Press INFO once to get extended information programme description and once again to close it Press OK to view the corresponding channel A No information yet message is displayed if the selected channel does not provide EPG data It may take a few seconds before data can be displayed 55 DCR 2020 indice3 25 09 07 14 17 Page 56 PHILIPS PHILIPS fitte a favourite Bit Settings Menu Basic navigation While watching digital TV or listening to digital radio Press MENU to display the main menu Press A or W to scroll up or down to the menu item you want to select Press OK to display the corresponding sub items Press A or V to move to the desired sub item Press MENU to go back to the main menu or BACK to go back one step in the menu or EXIT to return to normal viewing Changing settings Once you highlighted an adjustable item or sub item you can then access the values a
28. t in case emergency shutdown is required Do not place any combustible objects on the receiver candles etc No objects filled with liquids such as vases shall be placed on the unit The receiver shall not be exposed to dripping or splashing Should this happen disconnect your receiver from the mains and consult your dealer Make sure that children do not place any foreign objects in any of the openings For cleaning use a soft damp not wet cloth Never use any abrasive cloth and aerosol cleaners 37 DCR 2020 indice3 25 09 07 14 17 Page Unpacking the receiver As you unpack your terminal make sure the following accessories are included 1 x Remote Control Unit 2x AA batteries 1 x SCART Cable 1 x Power Cord 1 x Antenna Cord type F IEC 1 x Adapter F male IEC female 1 x Sticker to be put on your smart card 1 x Leaflet explaining what to do with the adapter and sticker mentioned above 1 x User Manual 1 x Worldwide Warranty booklet Plastic bags can be dangerous To avoid suffocation keep the bag away from babies and children Quick installation guide Refer to the safety section before connecting your terminal I Disconnect your TV set and recorder from the mains 2 Screw the adapter supplied with your receiver on the RF IN connector of the rear panel 3 Integrate your terminal in your existing installation as shown on the diagram TV set u a Cable iR P
29. the mode allowing control by your digital receiver Recording with the VCR control feature Your digital receiver TV and VCR or DVD are connected and set according to the diagram You have programmed a timer on your digital receiver as described in paragraph Timers At timer start your VCR or DVD starts recording and at timer end it stops recording under the control of your digital receiver You no longer need VCR or DVD programming to record digital TV channels 65 DCR 2020 indice3 25 09 07 14 18 Page se 66 Troubleshooting Problem The display on the front panel does not light up Possible cause Faulty power supply Action Check that the power cord is correctly connected Disconnect this cord and reconnect it to ensure it is in place Check that the power is available at the wall socket No sound or picture but the front panel red light is on Receiver in standby Press P P or any number key of the remote control If the receiver does not wake up press on the front panel No sound or picture but the front panel green light is on Poor signal Receiver in TV mode Poor SCART connections Check the connections at the wall socket and receiver Press TV STB on the remote control once or twice Check the SCART connections The remote control does not operate your receiver Make sure the receiver is on Make sure you are pointing your remote control at
30. the receiver front panel Check the batteries in your remote control On screen display working but there is no reception Poor reception signal Check the installation Intermittent reception Faulty connections Check all connections and cable The picture is not sharp and on screen text is difficult to read TV SCART output format not set to RGB TV SCART not connected to the RGB capable SCART socket of your TV set Inappropriate TV SCART Change setting of the TV output signal item to RGB from the TV Configuration screen Refer to your TV User Manual Use the SCART cable supplied with your receiver You cannot find all the channels you think should be available The signal may be weak Try retuning your receiver following the relevant steps in paragraph Channels installation If you are still missing channels call your customer service adviser 9 DCR 2020 indice3 25 09 07 14 18 Page Ep Problem Possible cause The picture on some The broadcast is probably in channels seems to have been wide screen and the receiver stretched or squashed settings may not be correct Action Check the receiver TV format setting following the information in paragraph TV Configuration If you have a wide screen TV you may also need to check the settings on your TV Even if you use the number The parental lock has been buttons you cannot access a activated on this channel and
31. z Standby power consumption lt 7W Green Specifications Banned Substance Declaration Yes Packaging Manufacturer Yes ODM Lead free soldered product The product complies with the following European Directives C 73 23 EEC 93 68 EEC 89 336 EEC AC3 and Dolby Digital are registered trademarks of Dolby Laboratories Licensing Corporation Due to continued product improvements this information is subject to change without notice DCR 2020 indice3 25 09 07 14 18 Page 69 DCR 2020 indice3 25 09 07 14 18 Page e PHILIPS Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners 2006 Koninklijke Philips Electronics N V All rights reserved Document order number 3111 176 52563 9
Download Pdf Manuals
Related Search